all | frequencies |
|
|
|
|
|
exhibits | applications |
---|---|---|---|---|---|---|---|---|
manual | photos | labels |
app s | submitted / available | |||||||
---|---|---|---|---|---|---|---|---|
1 |
|
User Manual | Users Manual | 1.44 MiB | ||||
1 |
|
Internal photos | Internal Photos | 710.02 KiB | ||||
1 |
|
External Photos | External Photos | 180.22 KiB | ||||
1 |
|
Label | ID Label/Location Info | 302.31 KiB | ||||
1 |
|
Label location | ID Label/Location Info | 71.85 KiB | ||||
1 |
|
Authorization Letter | Cover Letter(s) | 105.55 KiB | ||||
1 |
|
Family Model Letter | Cover Letter(s) | 82.65 KiB | ||||
1 |
|
LTC Letter | Cover Letter(s) | 99.65 KiB | ||||
1 | RF Exposure Info | |||||||
1 | Test Report | |||||||
1 | Test Setup Photos | |||||||
1 |
|
SDoC Declaration Letter | Attestation Statements | 78.73 KiB | ||||
1 |
|
WLAN Channels Declaration Letter | Cover Letter(s) | 99.44 KiB |
1 | User Manual | Users Manual | 1.44 MiB |
User Guide DL-820 Thermal Desktop Label Printer Tally Dascom DL-820 User Guide V1.0 Important Safety Instructions (English) Read the following instructions thoroughly before starting up your printer. Never carry out maintenance or repair work yourself. Always contact a qualified service technician. Keep this Operators Manual in a place which is easily accessible at all times. Place the printer on a solid and even base so that it cannot fall. Never place the printer in the vicinity of inflammable gas or explosive substances. Ensure the printer is connected to a socket with the correct mains voltage. Always disconnect the printer from the mains before opening the device to perform maintenance work or remedy errors. Do not expose the printer to high temperatures, direct sunlight or dust. Keep all liquids away from the printer. Protect the printer from shock, impact and vibration. Make sure that the printer and computer are switched off before connecting the data cable. The print head will become very hot during printing; avoid contact with the print head after printing has finished. Do not perform any operation or action in any way other than those provided in this manual. When in doubt, contact your dealer or your customer support. The device and mains-socket must all times be easily accessible. I Tally Dascom DL-820 User Guide V1.0 Wichtige Sicherheitshinweise (German) Lesen Sie bitte diese Sicherheitshinweise durch, bevor sie den Drucker in Betrieb nehmen. Fhren Sie Wartungsarbeiten und Reparaturen keinesfalls selbst aus, sondern verstndigen Sie immer einen qualifizierten Servicetechniker. Bewahren Sie diese Dokumentation an einem jederzeit zugnglichen Ort auf. Den Drucker auf stabilem und ebenem Untergrund so aufstellen, dass er nicht zu Boden fallen kann. Stellen Sie den Drucker keinesfalls in der Nhe von leicht entzndlichen Gasen oder explosiven Stoffen auf. Den Drucker nur an eine Steckdose mit der richtigen Spannung anschlieen. Wenn Sie den Drucker vom Netz trennen wollen, den Drucker ausschalten und immer den Netzstecker an der Steckdose ziehen. Keine Flssigkeiten mit dem Drucker in Berhrung bringen. Den Drucker weder hohen Temperaturen noch direktem Sonnenlicht und Staub aussetzen. Den Drucker keinen Erschtterungen, Sten oder Vibrationen aussetzen. Sicherstellen, dass der Drucker und der Computer ausgeschaltet sind, bevor das Datenkabel angeschlossen wird. Der Druckkopf wird whrend des Druckens hei. Vor dem Berhren deshalb einige Zeit abkhlen lassen. Weichen Sie bei der Bedienung des Druckers nicht von den Anweisungen in der Dokumentation ab. Bei Unklarheiten wenden Sie sich bitte an Ihren Hndler oder Ihren Kundendienst. Maschinenlrminformations Verordnung 3.GPSGV, der hchste Schalldruckpegel betrgt 70 dB(A) oder weniger gem EN ISO 7779. Das Gert und die Netzsteckdose mssen jeder Zeit leicht zugnglich sein. II Tally Dascom DL-820 User Guide V1.0 Consignes importantes de scurit (French) Lire attentivement les instructions suivantes avant de mettre limprimante en service. Ne jamais effectuer soi-mme les travaux dentretien et de rparations. Contacter toujours un dpanneur qualifi. Placer limprimante sur un support stable de faon ce quelle ne puisse pas tomber. Ne jamais placer limprimante proximit de sources de gaz aisment inflammables ou de substances explosives. Ne connecter limprimante une prise que lorsque la tension est correcte. Pour dconnecter limprimante de lalimentation principale, mettre limprimante hors tension et toujours dbrancher le connecteur secteur de la prise murale. Ne pas exposer limprimante des tempratures leves, la lumire directe du soleil ou la poussire. Ne pas mettre limprimante en contact avec des liquides. Ne pas exposer limprimante des chocs, impacts ou vibrations. Sassurer que limprimante et lordinateur sont hors tension avant de connecter le cble de donnes. La tte dimpression est brlante pendant limpression. Cest pourquoi laissez-la refroidir quelques instants avant dy toucher. N'excutez aucune opration ni action d'une autre manire que celle indique dans ce manuel. En cas de doute, veuillez contacter votre distributeur ou service aprs-vente. Le dispositif et la prise principale doivent toujours tre accessibles facilement. III Tally Dascom DL-820 User Guide V1.0 Indicazioni di sicurezza importanti (Italian) Prima di mettere in funzione la stampante, leggere attentamente le seguenti indicazioni. Non eseguire mai da s gli interventi di manutenzione e riparazione, ma rivolgersi sempre a un tecnico di assistenza qualificato. Conservare le presenti istruzioni per luso in un luogo sempre accessibile. Collocare la stampante su una superficie stabile, per evitare che cada a terra. Non collocare la stampante in prossimit di gas facilmente infiammabili o di sostanze esplosive. Collegare la stampante a una presa di corrente con tensione adeguata. Per scollegare la stampante dalla rete di alimentazione, spegnere la stampante e disinserire sempre il connettore di rete dalla presa. Non esporre la stampante ad elevate temperature n alla luce solare diretta e alla polvere. Evitare il contatto della stampante con liquidi. Non esporre la stampante a colpi, scosse o vibrazioni. Verificare che la stampante e il computer siano spenti prima di collegare il cavo di trasmissione dati. Durante la stampa, la testina si surriscal-da notevolmente. Prima di toccarla, se necessario opportuno quindi lasciarla raffreddare qualche istante. Non eseguire alcuna operazione o azione se non nella maniera descritta nel presente manuale. In caso di dubbio, contattare il rivenditore o dalla societ incaricata dellassistenza. Il dispositivo e la presa di corrente devono essere sempre facilmente accessibili. IV Tally Dascom DL-820 User Guide V1.0 Instrucciones de seguridad importantes (Spanish) Lea las siguientes instrucciones con esmero antes de poner la impresora en servicio. Nunca lleve a cabo trabajos de mantenimiento o reparacin Ud. mismo, sino consulte a un tcnico de servicio calificado. Guarde las presentes instrucciones de servicio en un lugar de fcil acceso en cualquier momento. Ponga la impresora sobre un base estable de manera que no pueda caer al suelo. Nunca coloque la impresora en la vecindad de gases de fcil inflamabilidad o sunstancias explosivas. Asegure conectar la impresora slo a un enchufe con un voltaje correcto. Cuando quiera desconectar la impresora de la red, apague la impresora y siempre tire la clavija de alimentacin del enchufe. No exponga la impresora a temperaturas altas, a la luz solar directa y al polvo. No ponga la impresora en contacto con fluidos. Nunca exponga la impresora a sacudidas, choques o vibraciones. Asegrese de que la impresora y el ordenador estn apagdos antes de conectar el cable de datos. La cabeza de impresin se pone muy caliente durante la impresin. Por lo tanto, deje enfriarlo algn tiempo antes de tocarla. No permita que se realice cualquier operacin o accin de una forma diferente a lo que se seala en el manual. En caso de duda, pngase en contacto con su comerciante o con su servicio post-venta. El dispositivo y la toma de corriente deben estar ubicados de forma que sea fcil acceder a ellos. V Tally Dascom DL-820 User Guide V1.0
. (Russian)
, ,
.
,
.
, .
,
.
, .
, .
, ,
. -
, .
, .
, . VI Tally Dascom DL-820 User Guide V1.0 Instrues Importantes sobre Segurana (Portuguese) Leia as instrues de segurana antes de usar a impressora. Consulte sempre um tcnico qualificado para executar uma reparao . Coloque a impressora sobre uma base slida e nivelada, para que ela no sofra quedas. Jamais instale a impressora nas proximidades de lugares onde haja gs inflamvel ou substncias explosivas. Assegure-se de conectar a impressora tomada eltrica com a voltagem apro-priada. Quando desligar a impressora da rede, desligue sempre a impressora e retire o cabo da tomada. No exponha a impressora a temperaturas altas ou luz solar direta. No aproxime substncias lquidas da impressora. Proteja a impressora de choques, impactos e vibraes. Desligue a impressora e o computador antes de conectar o cabo da rede. A cabea da impressora pode ficar muito quente . Portanto, espere algum tempo antes de toc-la. No faa nenhuma operao ou ao alm das recomendadas neste manual. Em caso de dvida, contate seu revendedor ou companhia de servio. A impressora e a tomada devem ser facilmente em todos os momentos acessveis. VII Tally Dascom DL-820 User Guide V1.0 nemliGvenlik Talimatlar (Turkish) Ltfen, yazcy iletime geirmeden nce bu gvenlik talimatlarn btnyle dikkatleokuyun. Bakm ve tamir almalarn kesinlikle ve hibir surette kendibanza yapmayn; her zamankalifiyebir uzmanservis-teknisyenine haber verin. Yazcy, zerinden yere dmesimmkn olmayacak sabitve dz birzemineyerletirin. Yazcy kesinlikle ve hibir surette kolayca yanabilecek gaz veyapatlayc maddeler ieren nesnelerin yaknna koymayn. Yazcakmkablosunu sadece doru gerilime sahipbirprizetakn. Yazcy ebeke andan ayrmak istediinizde, yazcy kapatn ve a-fiini her zamanprizden kartn. Yazcy ne yksek sl ne de dorudan gne na ve toza mruz kalanmeknlarda bulundurun. Yazchibir sv maddeyle temastaolmamaldr. Yazc hibir sarsntya, darbeye veyatitreime mruzkalmamaldr. Veri kablosu balanmadan nce hem yazcnn hem de bilgisayarn kapalolduklarndan emin olmalsnz. Yazcnn ba basmaesnasnda yksek sya ulayor. Bu yzdenltfendokunmadan nce ksa sre soumasn bekleyin. Yazcnn iletimi ve kullanmnda bu dokmantasyondaki talimatlarn hi dna kmayn. Sorunlu grnen hususlarda ltfenimlatnza veyamteri hizmetleri servisinize bavurun. Cihaz ve elektrik prizinin her zaman kolayca eriilebilir olmas gerekir. VIII Tally Dascom DL-820 TRADEMARK ACKNOWLEDGEMENTS User Guide V1.0 IBM is a trademark of International Business Machines Corporation. EPSON is a trademark of Epson America Incorporated. DEC is a trademark of Digital Equipment Corporation. Centronics is a trademark of Centronics Data Computer Corporation. DOS is a trademark of Microsoft Corporation. SAP is a trademark of SAP AG. Windows, Windows 7,Windows 8, Windows 10 , Windows 95, Windows 98, Windows NT, Windows 2000, Windows 2003/2008/2013 Server, Windows XP and Windows Vista are trademarks of Microsoft Corporation. All other product names and company names appearing in this manual are the registered trademarks or trademarks of the individual companies. IX Tally Dascom DL-820 User Guide V1.0 Contents 2.5 CHAPTER 1 INTRODUCTION......................................................................................................................... 1 1.1 Features......................................................................................................................................................1 1.2 Specifications.............................................................................................................................................2 1.3 Consumables.............................................................................................................................................3 1.4 Size and Weight........................................................................................................................................ 4 1.5 Unpack and Inspect..................................................................................................................................5 1.6Standard/optional components for the product.....................................................................................7 Key components.......................................................................................................................... 8 1.7 Control Panel........................................................................................................................ 13 1.8 1.8.1 Normal/Setup modes operation................................................................................................ 13 1.8.2 Four major setup menus.............................................................................................................14 1.8.3 Sample for setup steps................................................................................................................14 1.9 Displayed error messages.....................................................................................................................15 CHAPTER 2 INSTALLATION.........................................................................................................................16 2.1 Recommended installation procedures...............................................................................................16 2.2 Suitable installation site........................................................................................................................ 16 2.3 Connect the power..................................................................................................................................17 2.4 Adjust the media sensors...................................................................................................................... 18 2.4.1 Two types of media sensors...................................................................................................... 18 2.4.2 Relocate the Gap Sensor............................................................................................................ 19 2.4.3 Relocate the (Reflective) Black Mark Sensor........................................................................19 Load the media........................................................................................................................ 20 2.5.1 Loading procedures..................................................................................................................... 20 2.5.2 Adjust the media thickness and width.................................................................................... 22 Load the ribbon........................................................................................................................ 24 2.6.1 Loading procedures..................................................................................................................... 24 2.6.2 Resolve the wrinkled ribbon by adjusting the Ribbon Balance Gear............................ 25 2.6.3 Resolve the wrinkled ribbon by adjusting the Ribbon Supply Leveler......................... 26 2.7 Connect the interface............................................................................................................................. 27 CHAPTER 3 SOFTWARE INSTALLATION................................................................................................. 28 3.1 Installing the Driver.................................................................................................................................28 3.2 Installing the Configuration Tool........................................................................................................... 32 3.3 Using the Configuration Tool.................................................................................................................35 3.3.1Setup for the media with black marks......................................................................................35 3.3.2 Setup for the LAN connection................................................................................................... 37 3.4 Upgrading the Firmware........................................................................................................................ 38 CHAPTER 4 SUPPORT UTILITIES...............................................................................................................40 4.1 Configuration list (self-test page)......................................................................................................... 40 Hex-dump........................................................................................................................ 41 4.2 4.3 Auto media registration........................................................................................................................ 41 CHAPTER 5 DIAGNOSTICS AND MAINTENANCE..................................................................................42 5.1 Diagnostics...............................................................................................................................................42 5.2 Restore factory default settings............................................................................................................43 5.3 Clear jammed media.............................................................................................................................. 43 5.4 Clean the print head............................................................................................................................... 43 5.5 Cleaning....................................................................................................................................................44 2.6 User Guide V1.0 Tally Dascom DL-820 CHAPTER 6 INTERFACE SPECIFICATIONS............................................................................................ 45 6.1 USB........................................................................................................................................................... 45 6.2 Ethernet.................................................................................................................................................... 45 6.3 Parallel...................................................................................................................................................... 46 6.4 Serial......................................................................................................................................................... 47 6.5 Wifi.............................................................................................................................................................47 CHAPTER 7 OPTION INTRODUCTION.......................................................................................................49 7.1 Using the cutter.......................................................................................................................................49 7.2 Using the peeler......................................................................................................................................50 CHAPTER 8 CODE PAGES........................................................................................................................... 54 8.1 ASCII character set.................................................................................................................................54 8.2 CP 437 USA.............................................................................................................................................55 8.3 CP 850...................................................................................................................................................... 56 8.4 CP 860 Portuguese................................................................................................................................ 57 8.5 CP 863 French........................................................................................................................................ 58 8.6 CP 865 Nordic......................................................................................................................................... 59 8.7 CP 858 European....................................................................................................................................60 8.8 CP 866 Cyrillic......................................................................................................................................... 61 8.9 CP 852 Latin............................................................................................................................................ 62 CHAPTER 9 COMMAND CODES.................................................................................................................64 9.1 ZPL Command Set................................................................................................................................. 64 9.2 EPL Command Set................................................................................................................................. 68 Tally Dascom DL-820 User Guide V1.0 Chapter 1 Introduction Dascom designs this competitive industrial thermal label printer with the resolution of 203 dpi
(dots per inch) printing at 8 ips (inches per second). Generous media storage and multiple emulations supporting ZPL, EPL, TSPL best fit for medical, manufacturing, logistics, retail & service, postal and education applications. 1.1 Features Nearly 90 cap opening for effortless media and ribbon replacement. Pull down to tear for easy cutting of short-width labels. Generous storage for 360-meter ribbon and 203 mm diameter media to reduce frequent replacement. Movable media sensor for precise positioning of media with off-center registration maker. Multiple interfaces: USB and LAN built-in, parallel option. Other optional parts:
Cutter, label peeler 1 Tally Dascom DL-820 1.2 Specifications User Guide V1.0 Print Parameter Fonts Graphics Barcodes Ribbon Media Handling Control Panel Detect Function Emulation Print method Print width Print speed Print head Resolution Chinese Alphanumeric User-defined Code Pages Scalable
/Rotation Graphics processing 1D 2D OD ID Length Width Media Spec. Media cut Media type Key LED indicator Screen Standard sensors Optional sensor Zebra Direct thermal/Thermal transfer printing Max. 108mm Max. 8 ips (203dpi) Dot pitch: 0.125mm 203DPIx203DPI GB18030 2424 (Simplified/Traditional Chinese) Resident single byte (ZPL): Font A, Font B, Font D, Font E, Font F, Font G, Font H, Font V0, Font GS, Font P, Font Q, Font R, Font S, Font T, Font U, Font V User-defined fonts can be downloaded into FLASH, SDRAM. EPL:
PC437;PC850;PC852;PC860;PC863;PC865;PC857;PC861;PC862;PC85 5;PC866; PC737;PC851;PC869;Windows 1252;Windows 1250;Windows 1251; Windows 1253;Windows 1254;Windows 1255 ZPL:
PC850, windows 1250, windows 1252, windows 1251, windows 1253, windows 1254, windows 1256 Zoom in 1~8 times in vertical or horizontal, rotate by 00, 900, 1800, 2700. Graphics (Monochrome PCX, BMP) can be downloaded into SDRAM. 2 of Code;
5;Code 49;Planet ZPL:
Code11;Interleaved 39;Code EAN-8;EAN-13;UPC-E;UPC-A;Code 93;Code 128;
Industrial 2 of 5;Standard 2 of 5;Codabar;MSI;Plessey EPL:
EAN-8;EAN-13;UPC-E;UPC-A;Code 39;Code 93;Code 128; Interleaved 2 of 5 ZPL:
PDF417;CODABLOCK;Maxicode;Aztec;QR Code; Data Matrix;
EPL:
PDF417;Maxicode;QR Code; Data Matrix;
Max. 70mm (2.7 in) 25 mm (1 in) Max. 360 m 25.4~114mm Thickness 0.06~0.25mm Width 19.6mm~120mm Length 8.9~400mm Max. OD 203mm (8 in) ID 25.4 mm~76.2 mm (1 inch~3 inch) Tear bar, auto-cutter, peeler Roll paper, fanfold paper
(continuous, non-continuous, continuous tag, wrist-band, normal media and all sorts of receipts ) Four keys: Feed, Return, Pause, Cancel One LED: Power LCD Black mark sensor, Media sensor, Ribbon sensor, Machinery sensor kit Label peel-off sensor ZPL, EPL, TSPL 2 Tally Dascom DL-820 User Guide V1.0 External power adapter AC 100V-240V, 50-60Hz DC 24V1.5A 32MB 8 MB USB (2.0 Full-Speed) Ethernet: 10M/100M Parallel Centronics (IEEE-1284) Driver (Windows 32bit/64bit), Bartender, SDK system 240(W)440(D)255(H)mm Black 9.8kg 0~45 20%~95%RH (non-condensing)
-20~60/95%RH (non-condensing) CE, FCC Cutter, Peeler 150km
(Condition: use specific thermal roll paper and the print rate is 12%) Power Supply Memory Interface Software Physical Spec. Certification Optional kit Reliability Input Output SDRAM FLASH Standard Optional Dimensions Casing Color Weight Operating condition Storage condition TPH lifetime 1.3 Consumables Important: Use genuine media to ensure the best print quality. The special designed paper, polyethylene and polyester media improve the performance and the print head life. This printer supports three classes of print media:
Adhesive Labels - individual label or continuous roll, with adhesive material on its back, laying over a backing tape (liner). Receipt - generally thermal sensitive paper in a roll. Ticket & Tag - generally made of thick paper (max. 0.25 mm); with perforation between label. The print media can be in a roll or fanfold. Thermal sensitive media (direct thermal) must be used without ribbon. Choose correct type of media for your application. 3 Tally Dascom DL-820 1.4 Size and Weight Width: ~240 mm Length: ~ 440 mm Height: ~255 mm Weight: ~9.8kg User Guide V1.0 Front View Rear View Side View 4 Tally Dascom DL-820 1.5 Unpack and Inspect User Guide V1.0 Unpack and inspect if any shipping damage or missing parts compared with the packing list:
Save all packing materials. Check if any exterior damages. Open the printer and inspect if any damages in the media compartment. If you find shipping damage, keep the packing materials and notify the re-seller. Contents in the packing list may vary according to your order. 5 Tally Dascom DL-820 Packing List for Standard Order User Guide V1.0 Parts Printer Ribbon Ribbon Rewinding Core Media Holder Thermal Paper Ribbon Spindles Media Width Adjuster Power Cord USB Cable GIG CD Quantity 1 set 1 roll 1 piece 1 piece 1 roll 2 pieces 1 piece 1 piece 1 piece 1 copy 1 piece Remark Wax base Contents: User Guide, GIG, Driver, Configuration Tool 6 Tally Dascom DL-820 1.6 Standard/optional components for the product User Guide V1.0 Parallel (optional) USB LAN Interfaces Cutting Sensor Product USB LAN Serial Parallel WLAN Blue tooth T e a r C u t t e r P e e e r l L a b e l M a r k l B a c k DL-820 X O X X O O Remarks: denotes standard component. O denotes optional component. X denotes unavailable component. 7 Tally Dascom DL-820 1.7 Key components 1 User Guide V1.0 2 3 4 6 5 9 7 8 No. Part Names 1 2 3 4 5 6 7 Transparent Window Top Cover Control Panel Rear Slot Power Socket Power Switch USB Interface 8 9 LAN Interface Optional interface:
parallel Descriptions Observe quantity of remained media. Open to replace media or ribbon. Configure the parameters and check the settings. An opening to load fanfold media Socket for detachable power cord. Turn on and off the printer USB connection to PC (ex-factory standard interface) LAN connection to the server (ex-factory standard interface) Optional interface to the PC. (Ordered separately) 8 Tally Dascom DL-820 User Guide V1.0 1 4 5 2 3 6 7 No. Part Names 1 Media Holder 2 3 4 5 6 7 Media Width Adjuster Media Compartment Ribbon Spindles Ribbon Drive Module Engage Handle Front Cover Descriptions With the Media Width Adjuster, they hold the media roll in position. Adjust it along the shaft of the Media Holder to match the width of the media. Generous space for media roll. One to supply and the other to rewind the ribbon. The mechanism to supply and rewind the ribbon. Press it to latch the print head/ribbon module in place. To be removed if optional cutter or label peeler is installed. 9 Tally Dascom DL-820 User Guide V1.0 1 2 3 4 No. 1 2 3 4 Part Names Media Thickness Dial Media Width Slider Release Lever Ribbon Balance Gear Descriptions Turn it to match with the media thickness Slide it to match with the media width. Push it to release the print head/ribbon module. Turn it to balance the ribbon tensions to correct wrinkled ribbon on the winding side. 10 Tally Dascom DL-820 User Guide V1.0 1 2 3 5 7 No. Part Names Print head Sensor Arm Gap Sensor
(Reflective) Black Mark Sensor Left Media Guide, fixed Right Media Guide, movable Feeding Roller 1 2 3 4 5 6 7 8 8 4 6 touch the head surface with fingers which Descriptions Never contaminate the head with grease or dirt. In normal position, it guides the media feeding. Lift it up to load media. Media registration by identifying the notch or gap separating adjacent tags or labels. Media registration by identifying the black mark pre-printed on the backside of the media. Guard the left edge of the media. Free to move guide guarding the right edge of the media. The friction between it and the print head drives printed media out of the printer. Damper It prevents media getting curved in high speed printing. 11 Tally Dascom DL-820 User Guide V1.0 1 2 3 4 No. Part Names 1 2 3 4 Ribbon Supply Leveler Ribbon Guide Shaft Ribbon Knobs Option Cover Descriptions It corrects ribbon wrinkle on the supply side by changing the tilted angle of the ribbon guide to balance the ribbon left/right tension. A routing pole for ribbon winding. Turn the knobs to tighten up the ribbon on loading or wrinkled. Open this cover to plug in the connectors for optional cutter or label peeler. Keep it closed if no options installed. 12 Tally Dascom DL-820 1.8 Control Panel 1.8.1 Normal/Setup modes operation User Guide V1.0 Normal Mode
(Ready to print operation) Setup Mode The 1st line constantly shows the model name. When the 2nd line shows one of the five major configuration menus, the 3rd line shows Setup. When the 2nd line shows a sub-menu the 3rd shows the valid configuration, setting value. Lights up to indicate the printer is turned on. Press twice to terminate the given item/value Scroll backward Scroll forward Accept the given item/value. LCD The 1st and 3rd lines constantly shows Setup, name and the model respectively. The 2nd line shows the current status, or the error message if a fault occurs. Power LED Lights up to indicate the printer is turned on. Enter Setup mode. button button button button job;
then Pause the print job. Complete the current print suspend the printer. For non-continuous media, advance to next label or top-of-form position. For continuous media, a press feeds the media 1 line; holding this button feeds multiple lines until the button is released. This action varies if options are enabled:
Label peeler: the label is fed to the peel off position. Further pressing the button has no effect until the label is removed. Auto-cutter: Printed label is fed to cut position directly. 13 User Guide V1.0 Tally Dascom DL-820 1.8.2 Four major setup menus Machine Information System Setup Net Config Test Mode 1.8.3 Sample for setup steps Below describes how to change the Print Density setting from 2 to 3 by panel operation. 1. The printer originally works in Normal mode with the follow display. 2. Press button once to enter Setup mode. Press button once to scroll forward getting the System Setup menu. 3. Press button once to accept entering the System Setup menu. Keep pressing button to scroll to Print density sub-menu. 4. Press button once to accept entering the Print density setting. Press button once to scroll the value from 2 to 3. 5. Press button to accept saving the value of 3 for Print density. 6. Press button twice to terminate Setup mode and return to Normal mode. 14 Tally Dascom DL-820 1.9 Displayed error messages User Guide V1.0 Besides showing the Normal status, the LCD displays error messages when faults occur:
LCD Message Print Ready Setup Pause Setup Head hot Setup Head Up Setup Paper Out Setup Calibrate Error Calibrate Error Setup Setup Ribbon Out Setup Ribbon Out Setup Cutter Error Setup The printer is in good operating condition and ready to print. Causes The or button on the Control Panel is press. This warns abnormal print head temperature. The print head is lifted up. This warns out of media. This warns not able to detect media present. This warns jammed media. This warns ribbon ended. This warns slipping ribbon winding.
*This warns cutting action is interfered by foreign objects.
* Valid if auto-cutter option is installed. 15 Tally Dascom DL-820 User Guide V1.0 Chapter 2 Installation 2.1 Recommended installation procedures 1. Installation location 2. Adjust the sensors 3. Load the media 4. Load the ribbon 5. Connect the interface 2.2 Suitable installation site Consider the following factors to choose the site to install the printer:
1. Install the printer on a solid, level and stable workbench surface. 2. Sufficient space around the printer to provide good ventilation, stack the printout, access the control panel, replace the ribbon/media, and carry the maintenance. 3. Avoid heat and damp sources. 4. Avoid an environment close to vibration and shock. 5. Ensure the power source is securely grounded. 16 Tally Dascom DL-820 2.3 Connect the power User Guide V1.0 Important: Check the voltage rating of the power source complies with that of the printer; incorrect voltage of the power source may cause hazard and damage the printer. 1. Switch off both the PC and the printer. 2. Connect the connector of the detachable cable to the printer power socket. 3. Connect the power plug to the wall socket. 4. If media and ribbon are installed, toggle the power switch to ON position to turn on the printer and the power LED will light up. Important:
1. Hold the power plug to unplug the power. 2. Pulling the power cord by force to unplug the power may break the power cord causing fire and electric shock. 3. Turn off the power if the printer is not in use for long period. 17 Tally Dascom DL-820 2.4 Adjust the media sensors 2.4.1 Two types of media sensors User Guide V1.0 The printer makes use of the media sensors to register the media to a precise position relative to the print head. You should activate the correct sensor for your media in use:
1. Gap sensor: for labels or tickets & tags - with a gap or notch separating consecutive media. 2. Black mark sensor: for receipts/tickets - with pre-printed black stripes on the back. label fanfold Gap sensor
(Reflective) Black Mark sensor Paper feed direction Only one media sensor can be active at anytime. According to the media in use, activate the appropriate sensor under the System Setup menu from the Control Panel or the Config Tool. Read Sections 2.4.2 and 2.4.3 to relocate the sensors according to the media width in use. 18 Tally Dascom DL-820 2.4.2 Relocate the Gap Sensor User Guide V1.0 When printing labels or ticket & tag media, activate Gap Sensor in the System Setup menu from the Configuration Tool or Control Panel. Additionally, relocate the sensor position to match the media width in use:
1. Open the top cover and unlock the print head. 2. 3. For labels with liner, move the Black Mark Sensor to a position within the physical label. If Load new media. (Read Section 2.5.) use media with notches, move the Black Mark Sensor underneath a notch. 4. See below photo. Align the two triangular markers on the Gap Sensor and Black Mark Sensor. 2.4.3 Relocate the (Reflective) Black Mark Sensor When printing media with black marks or black lines on the back, activate the Black Mark Sensor in the System Setup menu. Additionally, relocate the sensor position to match the media width in use:
1. Open the top cover and unlock the print head. 2. 3. See below photo. Move the Black Mark Sensor directly underneath the black mark of the Load new media. (Read Section 2.5.) 4. Move the Gap Sensor beyond the Black Mark Sensor; otherwise, the printer fails to detect media. out of media. 19 Tally Dascom DL-820 2.5 Load the media 2.5.1 Loading procedures User Guide V1.0 Please identify if the media requires a ribbon. Only temperature sensitive media do not require ribbons. Caution: To prevent media jam, always align the media to the left side of the printer. If dark tracks do not come out by scratches on the media surface, the media is not temperature sensitive and a ribbon is required. 1. Open the top cover. Push the blue Release Lever to release the head module. Lift the Sensor Arm. With the printing surface facing up, clam the media roll between the Media Holder and the Media Width Adjuster. Load the clammed roll into the media compartment. 2. Route the media underneath the Damper. Move the Right Media Guide to fit the media width. Return the Sensor Arm to its original position. Important: The printing surface faces upward. 20 Tally Dascom DL-820 User Guide V1.0 3. If new media, read Section 2.4.2 or 2.4.3 to relocate the media sensors. Push the blue Engage Handle to lock up the print head module. 4. Making a media calibration ensures the printing starts with the correct position on the fresh media. Hold the button and then turn on the power. After the beeper sounds twice, release the button to complete the media calibration process. Make media calibrations for the following situations:
A fresh media. A media with different size from the last print task. Blank printout from in-used media. Offset printout without changing the settings. 21 Tally Dascom DL-820 User Guide V1.0 2.5.2 Adjust the media thickness and width It is important to set correct thickness and width for media to improve the print quality. When every printout is poor in quality, the thickness is incorrect. When the printout is poor only on one side, the width is incorrect. When printing on thick media like tags, test the print quality with incremental thickness After replacing different size media or direct thermal media, test print quality with values. incremental width values. 1Adjust the media thickness Recommended Dial Positions Media 1-2 3-5 6-9 Direct thermal rolls, general labels Labels with thick liner Thick media like tags or tickets Above are just recommended settings for different media. Verify the setting with your test results. The ex-factory setting is 1-2. (The default thickness for general labels.) Please note that the combination of media thickness and hardness of the media may cause slight variation. Adjusting the thickness may resolve the problem of wrinkled ribbon. 22 Tally Dascom DL-820 2Adjust the media width Adjusting the position of the Media Width Slider applies an even pressure on the print head across the media width. When the printout is lighter on one side or crook print media, adjust the Slider with different positions. User Guide V1.0 CautionMust adjust the slider position to avoid jammed media causing head damage when narrow width media is used. Recommended Slider Positions Media width mm (inches) Head Pressure 1 2 3 4 5 6 7 8 9 19.5 ~ 30.0mm(0.77 ~ 1.18) 30.0 ~ 39.0mm(1.18 ~ 1.53) 39.0 ~ 49.0mm(1.53 ~ 1.92) 49.0 ~ 62.0mm (1.92 ~ 2.44) 62.0 ~ 76.0mm (2.44 ~ 2.99) 76.0 ~ 88.0mm(2.99 ~ 3.46) 88.0 ~ 99.0mm(3.46 ~ 3.89) 99.0 ~ 108mm(3.89 ~ 4.25) 108 ~ 118mm(4.25 ~ 4.65)
(default setting) Low High The above table states the standard setting for general situation. Adjust the Slider and make test prints when thick media are used or wrinkled ribbon occurs. 23 Tally Dascom DL-820 2.6 Load the ribbon 2.6.1 Loading procedures User Guide V1.0 If dark tracks do not come out by scratches on the media surface, the media is not temperature sensitive and a ribbon is required. Note Ribbons are required to print on non-thermal-sensitive media. Using ribbon to print on thermal media produces poor quality graphics and bar-codes. 1. 1 Insert the two Ribbon Spindles into the Ribbon Core and new ribbon roll. 2 Plug the Spindle loaded with ribbon onto the rear driving shaft of the Ribbon Drive module. 2. 1 Push the blue Release Lever to release the head module. 2 Pull the ribbon and fix the end to the Ribbon Core. Spread the middle portion of the ribbon evenly over the print head. Plug the Spindle, loaded with the Ribbon Core, onto the front driving shaft of the Ribbon Drive module. 3. 1 Turn the Spindles to wind up excess ribbon. Push the blue Engage Handle to lock up the Print head module. 2 Close the Top Cover. 24 Tally Dascom DL-820 2.6.2 Resolve the wrinkled ribbon by adjusting the Ribbon Balance Gear User Guide V1.0 When you observe loose ribbon on one side from the front or wrinkled ribbon, adjust the Ribbon Balance Gear resulted in even ribbon tensions on both ends. 1. Unfasten the shaft screw. 2. Turn the Ribbon Balance Gear to shift the shaft slightly forward or backward. 3. After the adjustment, tight up the shaft screw. 25 Tally Dascom DL-820 2.6.3 Resolve the wrinkled ribbon by adjusting the Ribbon Supply Leveler User Guide V1.0 When you observe loose ribbon on one side from the supply side or wrinkled ribbon, adjust the Ribbon Supply Leveler resulted in even ribbon tensions on both ends of the supply side. 1Unfasten the two screws fixing the metal plate. 2Unfasten the screw fixing the Leveler. 3Turn the Leveler to change the tilt angle of the metal plate and its shaft, which is in contact with the supply ribbon.. Clockwise to tilt the shaft upward. Anticlockwise to tilt the shaft downward. 4When you observe balance tensions on both ends of the supply ribbon, fix all 3 screws. 5Repeat the adjustment if you find wrinkle ribbon after fixing the screws. NOTE: Incorrect media thickness and width settings may cause wrinkle ribbon as well. If several attempts on Leveler adjustment fail to correct wrinkle ribbon, you should check the media thickness and width settings. 26 Tally Dascom DL-820 2.7 Connect the interface User Guide V1.0 This printer provides USB and LAN interfaces for standard shipment. Parallel option is available. You may decide to install additional interface to the backside of the printer. The procedures to connect the standard interface:
1. Disconnect or switch off the power supplied to the printer. 2. Plug in one end of the interface cable to the corresponding interface port. 3. Plug the other end of the cable to the PC port. Optional interface USB interface Power switch Power socket LAN interface Parts Power socket Power switch USB interface LAN interface Descriptions Connect to the connector on the power cord. Toggle it to turn the printer on or off. Communicate with the PC via USB connection. (standard interface) Communication with the LAN server. (standard interface) Optional Interface Reserve for the installation of option: parallel Requirements for interface cables:
To prevent radio emission and interference, completely shielded cable with conductive connector housing should be used. Consider the following factors to reduce emission/interference levels:
Use short interface cables. (Less than 1.5 m in length is recommended.) Separate the interface cable from the power cord. Avoid routing the interface cable within the power duct. 27 Tally Dascom DL-820 User Guide V1.0 Chapter 3 Software Installation 3.1 Installing the Driver Caution: Switch off the printer before installing the Windows printer driver. Run the Windows installation package in the CD came with the printer. 1 Carefully read the license agreement before checking the Accept tab and clicking the Next button. 28 Tally Dascom DL-820 2 Specify the installation folder (C:\\TallyDascom is the default). Then click Next. User Guide V1.0 3 Click Finish to proceed with the installation wizard. 29 Tally Dascom DL-820 4 Check the Install printer drivers tab and click Next. User Guide V1.0 5 Select the connection port. Then click Next. 30 Tally Dascom DL-820 User Guide V1.0 6 Confirm the installation information. Then click Finish. 7 Then the printer driver is successfully installed. Click Close. 31 Tally Dascom DL-820 User Guide V1.0 3.2 Installing the Configuration Tool Before this installation, turn on the computer and the printer. Click Cancel if the PC pops up the new device installation wizard. Run the Configuration Tool package in the CD that came with this printer. 1 Specify the installation folder. Then click Next. 32 Tally Dascom DL-820 2 Decide if you want to create a Start Menu folder. Then click Next. User Guide V1.0 3 Decide if you want to create a desktop shortcut for this Configuration Tool. 4 Confirm the installation information. Click Install to proceed. 33 Tally Dascom DL-820 User Guide V1.0 5 The Configuration Tool is successfully installed. Click Finish. 34 Tally Dascom DL-820 3.3 Using the Configuration Tool User Guide V1.0 You can conveniently setup the printer for your application or upgrade the firmware with this Configuration Tool. 3.3.1Setup for the media with black marks In Config Tool, click Connect; then click Setting. Select Reflective for Paper Sensor to support media with black marks. 35 Tally Dascom DL-820 User Guide V1.0 When you use the media with notches between labels, select the Gap Sensor. 36 Tally Dascom DL-820 User Guide V1.0 3.3.2 Setup for the LAN connection In Config Tool, click Connect; then click Setting. Select Net Config. Fill in the LAN information and then click Write. 37 Tally Dascom DL-820 3.4 Upgrading the Firmware User Guide V1.0 1Connect the printer to the PC with an USB cable. Click Upgrade in the Config Tool menu. 2 Locate the firmware file by clicking Browse. Then click Start. A message box pops up to ask for confirmation; click Confirm. 38 Tally Dascom DL-820 User Guide V1.0 3 When the progress bar reaches 100%the upgrade process is completed and the printer will be restarted. 39 Tally Dascom DL-820 User Guide V1.0 Chapter 4 Support Utilities 4.1 Configuration list (self-test page) Listing the configurations helps to confirm the printer is properly setup. The procedures to print out this configuration list:
1. Properly load the media. Close the top cover. Turn off the power. 2. Hold the button when turn on the printer. 3. Release the button after the power LED flashes once and the buzzer beeps once. The printer then prints out the configuration list. 40 Tally Dascom DL-820 4.2 Hex-dump User Guide V1.0 If the printer fails to print online but can print the configuration list offline, you may set the printer to operate in hex-dump mode to check the communication between the PC and the printer. Feedback any problem to our customer support with this hex-dump list. The procedures to set the printer operating in hex-dump mode:
Hold the button when turn on the printer. Release this key after the power LED flashes 3 times and the buzzer beeps 3 time. 4.3 Auto media registration If the media sensors are properly setup, the printer can detect and automatically register the media to proper position. 1. Ensure the media is loaded correctly. 2. After turn on the printer or lock the print head, the printer automatically carries the media registration processes. 41 Tally Dascom DL-820 User Guide V1.0 Chapter 5 Diagnostics and Maintenance This printer is highly reliable. For precaution, this chapter recommends solutions to problems. In the meantime, we describe some guidelines to maintain the printer in good conditions. Follow the safety guideline to prevent harms to the operators and the printer. 5.1 Diagnostics This list provides recommended solutions to the problems. Consult the re-sellers customer support if faults persists. Faults No power light Probable Causes Poor power connections Broken power cord Broken fuse Dirty print head Media fall on the head No printout but normal media feeding Improper ink ribbon Unclear printout Mismatch media and ribbon parameters Incorrect darkness Dirty or deformed rollers Media fall on the head Improper ink ribbon Improper media thickness Unbalance head pressure across the media width ribbon parameters Dirty or deformed rollers Incorrect codes and commands fro the PC Incorrect menu settings Improper sensitivity for the media sensor Recommended Solutions Ensure secure connections from the printer socket to the wall socket. Ensure to use power cord dedicated for this printer. the head. Check the switch box if the fuse is intact. Use supplied print head cleaning kit to clean Remove the blocking media from the head and clean the adhesive left on the head with a cloth soaked with alcohol
. (Using metallic tools to clear blocking media may damage the head.) Install genuine and correct type of ribbon for your media. combinations. driver settings. deformed. parts.) Adjust different media/ribbon setting Choose the proper density in the menu or Clean the rollers with alcohol. Replace them if to order the re-seller
(Consult Remove the blocking media from the head and clean the adhesive left on the head with a cloth soaked with alcohol
. (Using metallic tools to clear blocking media may damage the head.) Install genuine and correct type of ribbon for your media. Turn the Media Thickness Dial for proper clearance between the head and the media. Slide the Media Width Slider for proper head pressure. combinations.. deformed. parts.) Clean the rollers with alcohol. Replace them if to order the re-seller
(Consult If error message is displayed, check the communication contents, the software settings in the PC. Use the operation panel or Config Tool to correct the settings. 42 Print position shifted Mismatch media and Adjust different media/ribbon setting Tally Dascom DL-820 Faults Probable Causes Winkled ribbon Improper ribbon tension Left/right tension of the ribbon not balanced Incorrect darkness User Guide V1.0 Recommended Solutions Choose proper media sensor sensitivity. If the sensor problem persists, sensitivity level in System Setup. change Turn the Ribbon Winding Knob to adjust the the tension. Turn the Ribbon Balance Dial. Choose the proper density in the menu or driver settings. Improper media and ink Use genuine and correct type of supplies. ribbon
(Consult the re-seller for supplies.) Improper ribbon tension Turn the Ribbon Winding Knob to adjust the Slipping ribbon
(dirts accumulate) Jammed ribbon Incorrect ribbon winding Reversed ribbon tension. Reload the ribbon correctly Install the ribbon in the correct winding direction. 5.2 Restore factory default settings Sometimes restoring factory default settings helps to resolve the problems. There are three ways to do it:
When turn on the power, hold the key until the power LED flashes 4 times and the buzzer beeps 4 times. Use the Configuration Tool to restore factory defaults. Use control panel to restore factory defaults. 5.3 Clear jammed media Caution Beware of high temperature near the print head. Turn off the power. Open the top cover. Unlock and lift the print head. Remove the media attached to the ribbon. Remove the ribbon. Use a cotton swab, soaked with alcohol to clean up the print head. Reload the media. Reload the ribbon. Turn the winding knob to get the affected portion of ribbon out of the way. 5.4 Clean the print head Let the head cool down before cleaning. Avoid damage to the head with finger nails or solid objects. Turn off the power. Open the top cover and unload the ribbon. Clean the head with a cotton swab soaked with alcohol (alcohol, methanol, or isopropyl alcohol). 43 Tally Dascom DL-820 User Guide V1.0 To get good print quality, clean the head once every 3 months. 5.5 Cleaning This printer is toughly built to meet heavy load without regular maintenance. However regular cleaning can extend the operating life of the printer. It is recommended to clean the printer every 6 months or 300 operating hours. Turn off the power and unplug the power cord before cleaning. Pick up paper debris by a pair of tweezers. Clean up the dust inside by a brush or compact vacuum cleaner. Clean up the dirt inside with a clean cloth. Clean the platen with a soft cloth. Avoid damages to or loosing the cable winding and components inside. Avoid metallic objects falling into the electric areas to cause short-circuit. 44 Tally Dascom DL-820 User Guide V1.0 Chapter 6 Interface Specifications 6.1USB USB Pin Assignment Pin 1 2 3 4 Signal Name VBUS D-
D+
GND Color Red White Green Black USB B Female Connector:
6.2 Ethernet Pin Assignment Pin 1 2 3 4 5 6 7 8 Signal Name TX+
TX-
RX+
n/c n/c RX-
n/c n/c Description Transmit Data+
Transmit Data-
Receive Data+
Not connected Not connected Receive Data-
Not connected Not connected RJ-45 Connector:
45 Tally Dascom DL-820 6.3 Parallel User Guide V1.0 Pin Source Signal Name 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19~30 31 32 33 34~35 36 H H H H H H H H H P P P STROBE*
Data0 (LSB) Data1 Data2 Data3 Data4 Data5 Data6 Data7 (MSB) ACK*
BUSY PError Not Connected Not Connected Not Connected Logic Ground Chassis Ground Logic Ground INIT*
5V/500mA driver P FAULT*
Logic Ground Not Connected Not Connected Remarks: H - signal source from host; P - signal source from printer. 1284-B Connector:
46 Tally Dascom DL-820 6.4 Serial User Guide V1.0 The serial interface of this printer is compatible with RS-232, using DB25 hole type socket. Pin PIN1 PIN2 PIN 3 PIN 4 PIN 5 PIN 6 PIN 7 Signal Name GROUND TXD RXD RTS EMPTY DSR SIGNAL GROUND PIN 8~19 PIN 20 PIN 21~25 EMPTY DTR EMPTY The settings of serial interface can be checked by printing self-test page. The default baud rate is 38400bps, 8 data bit, no parity, and 1 stop bit. Handshaking protocol is DTR/DSR. Serial interface connector 6.5 Wifi Function description:
Network type User to select. STA- IP address will be obtained from the terminal network. AP- IP address will be obtained from the printer, which is acted as WIFI access point. Channel number User defined. It can be selected according to the channel number of the router. DHCP User defined. IP address can be obtained dynamically. Security mode User defined. User can select the security mode according to WIFI mode and router encryption type. Network name User defined. IP Address User defined. If Static Address Method is selected, type in the address the printer will use on the network. SubNetMask User defined. If Static Address Method is selected, type in the subnet mark of the network. 47 Tally Dascom DL-820 User Guide V1.0 GateWay User defined. If Static Address Method is selected, type in the gateway address of the network. WiFi Port Default value = 9100 Specification:
W l i r e e s s Item Wireless Standard Frequency Range Parameters IEEE802.11b/g/n 2.412~2.484 GHz Receiver Sensitivity Data Rate Modulation Transmit Power Antenna Interface 802.11b: -82 dBm @ 11Mbps typical 802.11g: -68 dBm @ 54Mbpstypical 802.11b: 1,2,5.5,11 Mbps 802.11g: 6,9,12,18,24,36,48,54 Mbps DSSS, OFDM, DBPSK, DQPSK, CCK, QAM16/64 802.11b: 162 dBmtypical 802.11g: 132 dBmtypical IPX/microstrip antenna 48 Tally Dascom DL-820 User Guide V1.0 Chapter 7 Option introduction 7.1 Using the cutter Cutter is the factory option of the printer. Below is the front view of the printer configured with cutter. cutter Enable the cutter in the setup menu 1. The printer originally works in Normal mode. Press button once to enter Setup mode. Press button once to scroll forward getting the System Setup menu. 2. Press button once to accept entering the System Setup menu. Keep pressing button to scroll to Cutter sub-menu. Press button once to accept entering Cutter setting. Press button once to scroll the value from Off to On. 3. Press button to accept saving the value of On for Cutter. Press button twice to terminate Setup mode and return to Normal mode. 49 Tally Dascom DL-820 7.2 Using the peeler User Guide V1.0 Peeler is the factory option of the printer. Below is the front view of the printer configured with peeler. peeler Load continuous tag 1. Load the continuous tag and press the switch on the swinging arm of the peeler to open it. the switch 50 Tally Dascom DL-820 User Guide V1.0 2. Pull out a piece of label paper and tear off the sticker, leaving the base paper. 3. Clamping the base paper without sticker with swinging arm. The base paper should be as straightening as possible to avoid paper jam. 51 Tally Dascom DL-820 User Guide V1.0 4. Close the swinging arm and press down the release lever to lock the print head. 52 Tally Dascom DL-820 Enable the peeler in the setup menu User Guide V1.0 1. The printer originally works in Normal mode. Press button once to enter Setup mode. Press button once to scroll forward getting the System Setup menu. 2. Press button once to accept entering the System Setup menu. Keep pressing button to scroll to Peeler sub-menu. Press button once to accept entering Peeler setting. Press button once to scroll the value from Off to On. 3. Press button to accept saving the value of On for Peeler. Press button twice to terminate Setup mode and return to Normal mode. 53 Tally Dascom DL-820 User Guide V1.0 Chapter 8 Code Pages 8.1 ASCII character set HEX 0 1 2 3 4 5 6 7 8 9 A B C D E F 0 NUL EOT ENQ ACK HT LF FF CR 00 01 02 03 04 05 06 07 08 09 10 11 12 13 14 15 1 DLE XON XOFF DC4 NAK CAN ESC FS GS RS 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 2 SP
!
#
$
%
&
(
)
*
+
,
-
.
/
32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 0 1 2 3 4 5 6 7 8 9
:
;
<
=
>
?
5 6 7 P Q R S T U V W X Y Z
[
\
]
^
_
`
a b c d e f g h i j k l m n o 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 p q R s t u V w x y Z
{
|
}
~
SP 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 3 4
@
A B C D E F G H I J K L M N O 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 54 Tally Dascom DL-820 8.2 CP 437 USA User Guide V1.0 HEX 8 9 A B C D E F 0 1 2 3 4 5 6 7 8 9 A B C D E F Pt a o 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 218 219 220 221 222 223 n SP 224 225 226 227 228 229 230 231 232 233 234 235 236 237 238 239 240 241 242 243 244 245 246 247 248 249 250 251 252 253 254 255 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 55 Tally Dascom DL-820 8.3 CP 850 User Guide V1.0 HEX 8 9 A B C D E F 0 1 2 3 4 5 6 7 8 9 A B C D E F a o 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 218 219 220 221 222 223
-
SP 224 225 226 227 228 229 230 231 232 233 234 235 236 237 238 239 240 241 242 243 244 245 246 247 248 249 250 251 252 253 254 255 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 56 Tally Dascom DL-820 8.4 CP 860 Portuguese User Guide V1.0 HEX 8 9 A B C D E F 0 1 2 3 4 5 6 7 8 9 A B C D E F Pt a o 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 218 219 220 221 222 223 n SP 224 225 226 227 228 229 230 231 232 233 234 235 236 237 238 239 240 241 242 243 244 245 246 247 248 249 250 251 252 253 254 255 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 57 Tally Dascom DL-820 8.5 CP 863 French User Guide V1.0 HEX 8 9 A B C D E F 0 1 2 3 4 5 6 7 8 9 A B C D E F 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 218 219 220 221 222 223 n SP 224 225 226 227 228 229 230 231 232 233 234 235 236 237 238 239 240 241 242 243 244 245 246 247 248 249 250 251 252 253 254 255 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 58 User Guide V1.0 E F 208 209 210 211 212 213 214 215 216 217 218 219 220 221 222 223 n SP 224 225 226 227 228 229 230 231 232 233 234 235 236 237 238 239 240 241 242 243 244 245 246 247 248 249 250 251 252 253 254 255 D 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 Tally Dascom DL-820 8.6 CP 865 Nordic HEX 8 9 A B C 0 1 2 3 4 5 6 7 8 9 A B C D E F Pt a o 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 59 Tally Dascom DL-820 8.7 CP 858 European User Guide V1.0 HEX 8 9 A B C D E F 0 1 2 3 4 5 6 7 8 9 A B C D E F a o 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 218 219 220 221 222 223
-
SP 224 225 226 227 228 229 230 231 232 233 234 235 236 237 238 239 240 241 242 243 244 245 246 247 248 249 250 251 252 253 254 255 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 60 Tally Dascom DL-820 8.8 CP 866 Cyrillic User Guide V1.0 HEX 8 9 A B C D E F 0 1 2 3 4 5 6 7 8 9 A B C D E F 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 218 219 220 221 222 223 SP 224 225 226 227 228 229 230 231 232 233 234 235 236 237 238 239 240 241 242 243 244 245 246 247 248 249 250 251 252 253 254 255 61 Tally Dascom DL-820 8.9 CP 852 Latin User Guide V1.0 HEX 8 9 A B C D E F 0 1 2 3 4 5 6 7 8 9 A B C D E F L l t 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 SP 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 d 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 218 219 220 221 222 223 224 225 226 227
-
240 241 242 243 228 244 SP 229 230 231 232 233 234 235 236 237 238 239 245 246 247 248 249 250 251 252 253 254 255 62 User Guide V1.0 E F 208 209 210 211 212 213 214 215 216 217 218 219 220 221 222 223 224 225 226 227 228 229 230 231 232 233 234 235 236 237 238 239 2 SP 240 241 242 243 244 245 246 247 248 249 250 251 252 253 254 255 Tally Dascom DL-820 8.10 CP 720 Arabic 9 HEX 8 A B C D 0 1 2 3 4 5 6 7 8 9 A B C D E F SP SP a SP SP SP SP SP SP
-
128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 SP 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 63 Tally Dascom DL-820 User Guide V1.0 Chapter 9 Command Codes 9.1 ZPL Command Set Code
^A
^A@
^B0
^B1
^B2
^B3
^B4
^B5
^B7
^B8
^B9
^BA
^BB
^BC
^BD
^BE
^BF
^BI
^BJ
^BK
^BL
^BM
^BO
^BP
^BQ
^BR
^BS
^BT
^BU
^BX
^BY Description Scalable/Bitmapped Font Use Font Name to Call Font Aztec Bar Code Parameters Code 11 Bar Code Interleaved 2 of 5 Bar Code Code 39 Bar Code Code 49 Bar Code Planet Code bar code PDF417 Bar Code EAN-8 Bar Code UPC-E Bar Code Code 93 Bar Code CODABLOCK Bar Code Code 128 Bar Code (Subsets A, B, and C) UPS MaxiCode Bar Code EAN-13 Bar Code MicroPDF417 Bar Code Industrial 2 of 5 Bar Codes Standard 2 of 5 Bar Code ANSI Codabar Bar Code LOGMARS Bar Code MSI Bar Code Aztec Bar Code Parameters Plessey Bar Code QR Code Bar Code GS1 Databar (formerly Reduced Space Symbology) UPC/EAN Extensions TLC39 Bar Code UPC-A Bar Code Data Matrix Bar Code Bar Code Field Default 64 Tally Dascom DL-820 User Guide V1.0 Code
^CC ~CC
^BZ
^CD
^CF
^CI
^CM
^CO
^CP
^CV
^CW
~DB
~DE
^DF
~DG
~DN
~DS
~DT
~DU
~DY
~EG
^FB
^FC
^FD
^FH
^FL
^FM
^FN
^FO
^FP
^FR
^FS
^FT
^FV
^FW Description Change Caret POSTAL Bar Code
~CD Change Delimiter Change Alphanumeric Default Font Change International Font/Encoding Change Memory Letter Designation Cache On Remove Label Code Validation Font Identifier Download Bitmap Font Download Encoding Download Format Download Graphics Abort Download Graphic Download Intellifont (Scalable Font) Download Bounded TrueType Font Download Unbounded TrueType Font Download Objects Erase Download Graphics Field Block Field Clock Field Data Field Hexadecimal Indicator Font Linking Multiple Field Origin Locations Field Number Field Origin Field Parameter Field Reverse Print Field Separator Field Typeset Field Variable Field Orientation 65 Tally Dascom DL-820 User Guide V1.0 Code
^MD
^MF
^ML
^MM
^MN
^MP
^MT
^MU
^MW
^NC
~NC
^ND
^NI
~NR
^NS
~NT
^PA
^PF
^PH ~PH
~PL
^PM
^PN
^PO
^PP ~PP
^PQ
^PR
~PR
~PS
^PW
~RO
^SC
~SD
^SE
^SF Description Media Darkness Media Feed Maximum Label Length Print Mode Media Tracking Mode Protection Media Type Set Units of Measurement Modify Head Cold Warning Select the Primary Network Device Network Connect Change Network Settings Network ID Number Set All Network Printers Transparent Change Wired Networking Settings Set Currently Connected Printer Transparent Advanced Text Properties Slew Given Number of Dot Rows Slew to Home Position Present Length Addition Printing Mirror Image of Label Present Now Print Orientation Programmable Pause Print Quantity Print Rate Applicator Reprint Print Start Print Width Reset Advanced Counters Set Serial Communications Set Darkness Select Encoding Table Serialization Field (with a Standard ^FD String) 66 Tally Dascom DL-820 User Guide V1.0 Code
^SI
^SN
^SP
^SQ
^SR
^SS
^SZ
^TB
^TO
~WC
^WD
~WQ
~WQ
^XA
^XB
^XF
^XG
^XS
^XZ
^ZZ Description Set Sensor Intensity Serialization Data Start Print Halt ZebraNet Alert Set Printhead Resistance Set Media Sensors Set ZPL Text Blocks Transfer Object Print Configuration Label Print Directory Label Write Query Examples Start Format Suppress Backfeed Recall Format Recall Graphic Set Dynamic Media Calibration End Format Printer Sleep 67 Tally Dascom DL-820 9.2 EPL Command Set User Guide V1.0 Code A B b C D EI EK ES f GG GI GK GM I JF LO LS N O P q Q R S X Z
^@
^default Description ASCII text 1D (EAN-8 / EAN-13 / UPC-A / Interleaved 25 / Codabar
/ UPC-E / Code39 / Code 128) 2D (Data Matrix / PDF417 / QR Code) Cut immediate Density Print soft font information Delete soft font Store soft font Cut position Print graphics Print graphics information Delete graphics Store graphics Select character set Enable top of form backup Line draw black Line Draw diagonal Clear image buffer Hardware options Print Set label width Set form length Set reference point Select speed Draw box Print direction Code comment line Reset Restore factory default 68 Tally Dascom DL-820 User Guide V1.0 This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause undesired operation. FCC Radiation Exposure Statement This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. FCC STATEMENT Changes or modifications not expressly approved by the responsible for compliance could void the users authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. 69 DASCOM REPRESENTATIVES GERMANY DASCOM EuropeGmbH Heuweg 3 D-89079 Ulm Deutschland Tel.: +49 (0) 731 2075 0 Fax: +49 (0) 731 2075 100 www.dascom.com SINGAPORE (ASIA PACIFIC) DASCOMAP Pte Ltd 2 Jurong East Street 21
# 05-42, IMM Building Singapore 609601 Phone:+65 6760 8833 Fax: +65 6760 1066 www.dascom.com FRANCE DASCOM EuropeGmbH 117 Avenue VictorHugo 92100 Boulogne-Billancourt France Phone:+33 (1) 73 02 51 98 www.dascom.com UNITED KINGDOM DASCOM GB Ltd Hart House,Priestley Road, Basingstoke, Hampshire RG24 9PU, England Phone:+44 (0) 1256 355130 Fax: +44 (0) 1256 481400 www.dascom.com AMERICAS Dascom Americas Corporation 34 Lakeview Court Verona, VA 24482 USA Phone:+1 (877) 434 1377 Fax: +1 (540) 242 7221 www.dascom.com CHINA JIANGMEN DASCOM COMPUTER PERIPHERALS CO., LTD No.399, jinxing Road, Jianghai District Jiangmen, P.R. China www.dascom.com All rights reserved. Translations, reprinting or copying by anymeansof this manual completeor in part or in any different form requires our explicit approval. We reserve the right to make changes to this manual without notice. All care has been taken to ensure accuracy of information contained in this manual. However, we cannot accept responsibility for any errors or damages resulting from errors or inaccuracies of information herein. 2018 DASCOM 70
1 | Label | ID Label/Location Info | 302.31 KiB |
72.00 mm Tally Authorized EU representative:
eS eo DASCOM Europe GmbH, Heuweg 3, DASCOM 89079 Ulm, Germany Model : DL-820 hate device complies with Eee 15 of the FCC Rules. B 2 jperation is subject to the following two conditions:
ooo tatoie a (1) This device may not cause harmful interference.and
(2) This device must accept any interference received, ID Number : 28.XXX.XXXX including interference that may cause undesired Ser. Number : XXXXXXXXXXXX operation. UCL No.:00 C a FCC ID: Z70DL8200 Fe MAC Address : XX-XX-XX-XX-XX-XX Manufacturer: Jiangmen Dascom Computer Peripherals Co., Ltd. Address: No.399 Jinxing Road,Jianghai District, Jiangmen City,Guangdong Province, P.R.China WW QO0'Or 72.00 mm Authorized EU representative: A DASCOM DASCOM Europe GmbH, Heuweg 3, 89079 Ulm, Germany Model : DL-820 This device complies with Part 15 of the FCC Rules. e R Operation is subject to the following two conditions:
Input: ee an (1) This device may not cause harmful interference.and
(2) This device must accept any interference received, ID Number : 28.XXX.XXXX including interference that may cause undesired Ser. Number : XXXXXXXXXXXX_ operation. UCL No.:00 a FCC ID:Z70DL8200 Fe C MAC Address : XX-XX-XX-XX-XX-XX Manufacturer: Jiangmen Dascom Computer Peripherals Co., Ltd. Address: No.399 Jinxing Road,Jianghai District, Jiangmen City,Guangdong Province, P.R.China v WwW QO0'Or
1 | Authorization Letter | Cover Letter(s) | 105.55 KiB |
775 Montague Expressway Milpitas, CA 95035 Tel: 408-526-1188 Fax: 408-526-1088 Email: TCB@siemic.com Project and Product Certification Representative Authorization Letter Reason for Amendment (current / obsolete) Initial Release (obsolete) Revised wording (obsolete) Updated company template (obsolete) Updated letter information (obsolete) Added FCC ID field (current) Revision History From 1.0 1.0 2.0 3.0 4.0 To 1.0 2.0 3.0 4.0 5.0 Approved Date Nov-14-2006 Sept25-2007 Jan-31-2012 May-23-2014 Sept 16 2014 SCS-F18: Project and Product Certification Representative Authorization Letter Page 1 of 2 Rev 5.0 Jiangmen Dascom Computer Peripherals Co.,Ltd. 2018.11.13 To: SIEMIC, INC. 775 Montague Expressway, Milpitas, CA 95035 USA Dear Sir/Madam, Re: Product Certification Representative Authorization Letter Jiangmen Dascom Computer Peripherals Co.,Ltd. hereby authorize SIEMIC, Inc. to act as a We, Certification Body for certifying for the following project(s):
Product description: Thermal desktop label printer Model name: DL-820, DL-820a, DL-820b FCC ID: Z7ODL8200 Sincerely,
Clients signature Clients name / title : Yingsheng Huang / Manager Contact information / address : No 399,Jin Xing Road,Jiang Hai District,Jiangmen City,Guang Dong Province,China Telephone: 0750-3867631 Fax No.: 0750-3867631 SCS-F18: Project and Product Certification Representative Authorization Letter Page 2 of 2 Rev 5.0
1 | Family Model Letter | Cover Letter(s) | 82.65 KiB |
Jiangmen Dascom Computer Peripherals Co.,Ltd. I, the undersigned, Yingsheng Huang:
The three models have the same technical construction including circuit diagram, PCB Layout, components and component layout, all electrical construction and mechanical construction, except the different model number. 1) Model No.: DL-820 2) Model No.: DL-820a 3) Model No.: DL-820b FCC ID: Z7ODL8200 Sincerely, Clients signature :
Clients name / title : Yingsheng Huang / Manager Contact information / address : No 399,Jin Xing Road,Jiang Hai District,Jiangmen City,Guang Dong Province,China Telephone: 0750-3867631 Fax No.: 0750-3867631
1 | LTC Letter | Cover Letter(s) | 99.65 KiB |
775 Montague Expressway Milpitas, CA 95035 Tel: 408-526-1188 Fax: 408-526-1088 Email: TCB@siemic.com Confidentiality Request Letter Revision History Reason for Amendment (current / obsolete) Initial Release (obsolete) Adding CFR 2.459 (obsolete) Updated company template & Added text box Added IC confidentiality letter form (obsolete) Corrections to STC form. Added reference to KDB
(obsolete)
(current) From 1.0 1.0 2.0 3.0 4.0 To 1.0 2.0 3.0 4.0 5.0 Approved Date Nov-14-2006 August 11 - 2008 Jan-31-2012 March-26-2015 Nov 19 2015 SCS-F19: Confidentiality Request Letter Page 1 of 2 Rev 5.0 Jiangmen Dascom Computer Peripherals Co.,Ltd. 2018/11/13 To:
Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD
Block Diagram Schematics
- Operational Description Subject: Permanent Confidentiality Request for FCC ID: Z7ODL8200 Pursuant to sections 0.457 and 0.459 of CFR 47, we respectfully request permanent confidential treatment of the following Exhibits accompanying this application as:
The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these materials may be harmful to the applicant and provide unjustified benefits to its competitors. The applicant understands that disclosure of this application and all accompanying documentation will not be made before the date of the Grant for this application. Sincerely,
Clients signature Clients name / title : Yingsheng Huang / Manager Contact information / address : No 399,Jin Xing Road,Jiang Hai District,Jiangmen City, Guang Dong Province,China Telephone: 0750-3867631 Fax No.: 0750-3867631 SCS-F19: Confidentiality Request Letter Page 2 of 2 Rev 5.0
1 | SDoC Declaration Letter | Attestation Statements | 78.73 KiB |
Jiangmen Dascom Computer Peripherals Co.,Ltd. Date:2018-11-13 To: Federal Communications Commission 7435 Oakland Mills Road Columbia, MD FCC ID: Z7ODL8200 To Whom It May Concern:
This letter is to ascertain that [Jiangmen Dascom Computer Peripherals Co.,Ltd.] Product
[Thermal desktop label printer] has been the unit(s) used for conducting FCC compliance testing. The SDoC portion has been conducted in accordance with FCC SDoC requirement as per Section 2.1077 compliance information. Supplier's Declaration of Conformity 47 CFR 2.1077 Compliance Information Unique Identifier: (DL-820, DL-820a, DL-820b) Responsible Party U.S. Contact Information ABC Corporation :
Street Address :
City, State :
Zip Code :
Telephone number or internet contact information:
DASCOM Americas 34 Lakeview Court Verona, Virginia 24482
(877) 434-1377 FCC Compliance Statement (e.g., products subject to Part 15) This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Sincerely, Signature:
Contact Name/Title: Yingsheng Huang / Manager Contact Information (Email/Tel): huangys@dascom.cn /0750-3867631
1 | WLAN Channels Declaration Letter | Cover Letter(s) | 99.44 KiB |
WIFI Channel 12 and 13 Declaration Letter Reason for Amendment Initial Release (current) Modify the select options Revision History From 0.0 1.0 To 1.0 2.0 Approved Date December 22, 2015 Sep-23-2016 SCS-F190 WiFi Channel 12&13 Declaration Letter Page 1 of 2 Rev.1.0 Created by William Graff Approved by Bao-Thuong Nguyen Jiangmen Dascom Computer Peripherals Co.,Ltd. No 399,Jin Xing Road,Jiang Hai District,Jiangmen City,Guang Dong Province,China WIFI Channel 12 and 13 Declaration Letter We declare the equipment identified below with regards to Channel 12 and 13 capabilities for FCC ID: Z7ODL8200 Declaration Product hardware does not have the capability to operate on Channel 12 and 13. Product hardware has the capability to operate on Channel 12 and 13. However, these two channels will be disabled via software and will not be accessible to user. Product hardware has the capability to operate on Channel 12 and 13. However, all the operated channels cant be changed in the RF parameter via software. All channels have complied with all of the requirements sets out in FCC Part 15.247. Product hardware has the capability to operate on WiFi Channel 12 and 13, and meets the requirements of KDB 594280 D01 v02r01. Please note:
1.) By default, this device operates in a mode that is compliant with the U.S. requirements. 2.) This device will also use supplemental information such as geo-location data to determine that it is operating outside the U.S., if necessary, to change its power. Such supplemental data will be derived from the following:
Global Navigation Satellite System (GNSS)7 sensors in the device Mobile Country Code (MCC),8 or MCC with a Mobile Network code (MNC), received from a CMRS9 carrier and received directly by a receiver on the device Country information derived from multiple adjacent access points (for example using IEEE Std 802.11d provisions) may be permitted on case-by-case basis Other suitable geo-location data based on IP addresses or other reliable source. Name / Title: Yingsheng Huang / Manager Signature:
Telephone: 0750-3867631 Fax No.: 0750-3867631 Date: 2018-11-13 SCS-F190 WiFi Channel 12&13 Declaration Letter Page 2 of 2 Rev.1.0 Created by William Graff Approved by Bao-Thuong Nguyen
frequency | equipment class | purpose | ||
---|---|---|---|---|
1 | 2018-11-27 | 2412 ~ 2462 | DTS - Digital Transmission System | Original Equipment |
app s | Applicant Information | |||||
---|---|---|---|---|---|---|
1 | Effective |
2018-11-27
|
||||
1 | Applicant's complete, legal business name |
Jiangmen Dascom Computer Peripherals Co.,Ltd.
|
||||
1 | FCC Registration Number (FRN) |
0021247903
|
||||
1 | Physical Address |
No 399,Jin Xing Road,Jiang Hai District
|
||||
1 |
Jiangmen City Guang Dong Province
|
|||||
1 |
China
|
|||||
app s | TCB Information | |||||
1 | TCB Application Email Address |
t******@siemic.com
|
||||
1 | TCB Scope |
A4: UNII devices & low power transmitters using spread spectrum techniques
|
||||
app s | FCC ID | |||||
1 | Grantee Code |
Z7O
|
||||
1 | Equipment Product Code |
DL8200
|
||||
app s | Person at the applicant's address to receive grant or for contact | |||||
1 | Name |
Y****** H********
|
||||
1 | Title |
Manager
|
||||
1 | Telephone Number |
0750-********
|
||||
1 | Fax Number |
0750-********
|
||||
1 |
1******@qq.com
|
|||||
app s | Technical Contact | |||||
n/a | ||||||
app s | Non Technical Contact | |||||
n/a | ||||||
app s | Confidentiality (long or short term) | |||||
1 | Does this application include a request for confidentiality for any portion(s) of the data contained in this application pursuant to 47 CFR § 0.459 of the Commission Rules?: | Yes | ||||
1 | Long-Term Confidentiality Does this application include a request for confidentiality for any portion(s) of the data contained in this application pursuant to 47 CFR § 0.459 of the Commission Rules?: | No | ||||
if no date is supplied, the release date will be set to 45 calendar days past the date of grant. | ||||||
app s | Cognitive Radio & Software Defined Radio, Class, etc | |||||
1 | Is this application for software defined/cognitive radio authorization? | No | ||||
1 | Equipment Class | DTS - Digital Transmission System | ||||
1 | Description of product as it is marketed: (NOTE: This text will appear below the equipment class on the grant) | Thermal desktop label printer | ||||
1 | Related OET KnowledgeDataBase Inquiry: Is there a KDB inquiry associated with this application? | No | ||||
1 | Modular Equipment Type | Does not apply | ||||
1 | Purpose / Application is for | Original Equipment | ||||
1 | Composite Equipment: Is the equipment in this application a composite device subject to an additional equipment authorization? | No | ||||
1 | Related Equipment: Is the equipment in this application part of a system that operates with, or is marketed with, another device that requires an equipment authorization? | No | ||||
1 | Grant Comments | Power listed is the maximum conducted output power. The antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter, except in accordance with FCC multi- transmitter product procedures. End-Users must be provided with transmitter operation conditions for satisfying RF exposure compliance. | ||||
1 | Is there an equipment authorization waiver associated with this application? | No | ||||
1 | If there is an equipment authorization waiver associated with this application, has the associated waiver been approved and all information uploaded? | No | ||||
app s | Test Firm Name and Contact Information | |||||
1 | Firm Name |
EST Technology Co., Ltd.
|
||||
1 | Name |
I**** H******
|
||||
1 | Telephone Number |
+86 0******** Extension:
|
||||
1 |
i******@gdest.cn
|
|||||
Equipment Specifications | |||||||||||||||||||||||||||||||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
Line | Rule Parts | Grant Notes | Lower Frequency | Upper Frequency | Power Output | Tolerance | Emission Designator | Microprocessor Number | |||||||||||||||||||||||||||||||||
1 | 1 | 15C | 2412.00000000 | 2462.00000000 | 0.0136000 |
some individual PII (Personally Identifiable Information) available on the public forms may be redacted, original source may include additional details
This product uses the FCC Data API but is not endorsed or certified by the FCC