all | frequencies |
|
exhibits | applications |
---|---|---|---|---|
manual |
app s | submitted / available | |||||||
---|---|---|---|---|---|---|---|---|
1 |
|
UM | Users Manual | 2.93 MiB | ||||
1 | External Photos | |||||||
1 | Cover Letter(s) | |||||||
1 | Cover Letter(s) | |||||||
1 | Attestation Statements | |||||||
1 | Internal Photos | |||||||
1 | RF Exposure Info | |||||||
1 | Test Report | |||||||
1 | Test Setup Photos | |||||||
1 |
|
label | ID Label/Location Info | 374.89 KiB | ||||
1 | ID Label/Location Info |
1 | UM | Users Manual | 2.93 MiB |
User Guide DT-330 Thermal Receipt Printer Tally Dascom DT-330 User Guide V1.0 Important Safety Instructions (English) Read the following instructions thoroughly before starting up your printer. The device and mains-socket must all times be easily accessible. Keep this user guide in a place which is easily accessible at all times. Place the printer on a solid and even base so that it cannot fall. Ensure the printer is connected to a socket with the correct voltage. Always disconnect the printer from the power before opening the device to perform Never carry out maintenance or repair work yourself. Always contact a qualified service technician. Never place the printer in the vicinity of inflammable gas or explosive substances. maintenance work or remedy errors. Make sure that both the printer and the computer are switched off before connecting the data cable. printing has finished. When in doubt, contact your dealer or your customer support. Do not expose the printer to high temperatures, direct sunlight or dust. Keep all liquids away from the printer. Protect the printer from shock, impact and vibration. Do not perform any operation or action in any way other than those provided in this manual. The print head will become very hot during printing; avoid contact with the print head after Tally Dascom DT-330 User Guide V1.0 Wichtige Sicherheitshinweise (German) Lesen Sie bitte diese Sicherheitshinweise durch, bevor Sie den Drucker in Betrieb nehmen. Den Drucker nur an eine Steckdose mit der richtigen Spannung anschlieen. Stellen Sie den Drucker keinesfalls in der Nhe von leicht entzndlichen Gasen oder explosiven Bewahren Sie diese Dokumentation an einem jederzeit zugnglichen Ort auf. Den Drucker auf stabilem und ebenem Untergrund so aufstellen, dass er nicht zu Boden fallen Das Gert und die Netzsteckdose mssen jeder Zeit leicht zugnglich sein. Fhren Sie Wartungsarbeiten und Reparaturen keinesfalls selbst aus, sondern verstndigen Sie immer einen qualifizierten Servicetechniker. kann. Stoffen auf. Wenn Sie den Drucker vom Netz trennen wollen, den Drucker ausschalten und immer den Netzstecker an der Steckdose ziehen. angeschlossen wird. abkhlen lassen. Weichen Sie bei der Bedienung des Druckers nicht von den Anweisungen in der Dokumentation ab. Bei Unklarheiten wenden Sie sich bitte an Ihren Hndler oder Ihren Kundendienst. Den Drucker weder hohen Temperaturen noch direktem Sonnenlicht und Staub aussetzen. Keine Flssigkeiten mit dem Drucker in Berhrung bringen. Den Drucker keinen Erschtterungen, Sten oder Vibrationen aussetzen. Sicherstellen, dass der Drucker und der Computer ausgeschaltet sind, bevor das Datenkabel Der Druckkopf wird whrend des Druckens hei. Vor dem Berhren deshalb einige Zeit Tally Dascom DT-330 User Guide V1.0 Consignes importantes de scurit (French) Lire attentivement les instructions suivantes avant de mettre limprimante en service. Le dispositif et la prise principale doivent toujours tre accessibles facilement. Ne jamais effectuer soi-mme les travaux dentretien et de rparations. Contacter toujours un Ne connecter limprimante une prise que lorsque la tension est correcte. Pour dconnecter limprimante de lalimentation principale, mettre limprimante hors tension Placer limprimante sur un support stable de faon ce quelle ne puisse pas tomber. Ne jamais placer limprimante proximit de sources de gaz aisment inflammables ou de dpanneur qualifi. substances explosives. et toujours dbrancher le connecteur secteur de la prise murale. poussire. donnes. quelques instants avant dy toucher. En cas de doute, veuillez contacter votre distributeur ou service aprs-vente. Ne pas mettre limprimante en contact avec des liquides. Ne pas exposer limprimante des chocs, impacts ou vibrations. Sassurer que limprimante et lordinateur sont hors tension avant de connecter le cble de Ne pas exposer limprimante des tempratures leves, la lumire directe du soleil ou la La tte dimpression est brlante pendant limpression. Cest pourquoi laissez-la refroidir N'excutez aucune opration ni action d'une autre manire que celle indique dans ce manuel. Tally Dascom DT-330 User Guide V1.0 Indicazioni di sicurezza importanti (Italian) Prima di mettere in funzione la stampante, leggere attentamente le seguenti indicazioni. Il dispositivo e la presa di corrente devono essere sempre facilmente accessibili. Non eseguire mai da s gli interventi di manutenzione e riparazione, ma rivolgersi sempre a un Conservare le presenti istruzioni per luso in un luogo sempre accessibile. Collocare la stampante su una superficie stabile, per evitare che cada a terra. Non collocare la stampante in prossimit di gas facilmente infiammabili o di sostanze esplosive. Collegare la stampante a una presa di corrente con tensione adeguata. Per scollegare la stampante dalla rete di alimentazione, spegnere la stampante e disinserire tecnico di assistenza qualificato. sempre il connettore di rete dalla presa. dati. opportuno quindi lasciarla raffreddare qualche istante. In caso di dubbio, contattare il rivenditore o dalla societ incaricata dellassistenza. Non esporre la stampante ad elevate temperature n alla luce solare diretta e alla polvere. Evitare il contatto della stampante con liquidi. Non esporre la stampante a colpi, scosse o vibrazioni. Verificare che la stampante e il computer siano spenti prima di collegare il cavo di trasmissione Non eseguire alcuna operazione o azione se non nella maniera descritta nel presente manuale. Durante la stampa, la testina si surriscal-da notevolmente. Prima di toccarla, se necessario Tally Dascom DT-330 User Guide V1.0 Instrucciones de seguridad importantes (Spanish) Lea las siguientes instrucciones con esmero antes de poner la impresora en servicio. Guarde las presentes instrucciones de servicio en un lugar de fcil acceso en cualquier Nunca lleve a cabo trabajos de mantenimiento o reparacin Ud. mismo, sino consulte a un El dispositivo y la toma de corriente deben estar ubicados de forma que sea fcil acceder a Ponga la impresora sobre un base estable de manera que no pueda caer al suelo. Nunca coloque la impresora en la vecindad de gases de fcil inflamabilidad o sustancias Asegure conectar la impresora slo a un enchufe con un voltaje correcto. Cuando quiera desconectar la impresora de la red, apague la impresora y siempre tire la clavija ellos. tcnico de servicio calificado. momento. explosivas. de alimentacin del enchufe. datos. algn tiempo antes de tocarla. seala en este manual. En caso de duda, pngase en contacto con su comerciante o con su servicio post-venta. No exponga la impresora a temperaturas altas, a la luz solar directa y al polvo. No ponga la impresora en contacto con fluidos. Nunca exponga la impresora a sacudidas, choques o vibraciones. Asegrese de que la impresora y el ordenador estn apagados antes de conectar el cable de La cabeza de impresin se pone muy caliente durante la impresin. Por lo tanto, deje enfriarla No permita que se realice cualquier operacin o accin de una forma diferente a lo que se Tally Dascom DT-330 User Guide V1.0
. (Russian)
, ,
.
,
.
,
.
, .
, .
, .
, .
, .
, ,
, . -
Tally Dascom DT-330 User Guide V1.0 Instrues Importantes sobre Segurana (Portuguese) Leia as instrues de segurana antes de usar a impressora. A impressora e a tomada devem ser facilmente em todos os momentos acessveis. Consulte sempre um tcnico qualificado para executar uma reparao . Coloque a impressora sobre uma base slida e nivelada, para que ela no sofra quedas. Jamais instale a impressora nas proximidades de lugares onde haja gs inflamvel ou Assegure-se de conectar a impressora tomada eltrica com a voltagem apro-priada. Quando desligar a impressora da rede, desligue sempre a impressora e retire o cabo da substncias explosivas. tomada. toc-la. contate seu revendedor ou companhia de servio. No exponha a impressora a temperaturas altas ou luz solar direta. No aproxime substncias lquidas da impressora. Proteja a impressora de choques, impactos e vibraes. Desligue a impressora e o computador antes de conectar o cabo da rede. A cabea da impressora pode ficar muito quente . Portanto, espere algum tempo antes de No faa nenhuma operao ou ao alm das recomendadas neste manual. Em caso de dvida, Tally Dascom DT-330 User Guide V1.0 nemli Gvenlik Talimatlar (Turkish) Ltfen, yazcy iletime geirmeden nce bu gvenlik talimatlarn btnyle dikkatle okuyun. Yazcy, zerinden yere dmesi mmkn olmayacak sabit ve dz bir zemine yerletirin. Yazcy kesinlikle ve hibir surette kolayca yanabilecek gaz veya patlayc maddeler ieren Cihaz ve elektrik prizinin her zaman kolayca eriilebilir olmas gerekir. Bakm ve tamir almalarn kesinlikle ve hibir surette kendi banza yapmayn; her zaman Yazc akm kablosunu sadece doru gerilime sahip bir prize takn. Yazcy ebeke andan ayrmak istediinizde, yazcy kapatn ve a-fiini her zaman prizden kalifiye bir uzman servis-teknisyenine haber verin. nesnelerin yaknna koymayn. kartn. bulundurun. olmalsnz. sre soumasn bekleyin. Yazcnn iletimi ve kullanmnda bu dokmantasyondaki talimatlarn hi dna kmayn. Sorunlu grnen hususlarda ltfen imlatnza veya mteri hizmetleri servisinize bavurun. Yazc hibir sv maddeyle temasta olmamaldr. Yazc hibir sarsntya, darbeye veya titreime mruz kalmamaldr. Veri kablosu balanmadan nce hem yazcnn hem de bilgisayarn kapal olduklarndan emin Yazcy ne yksek sl ne de dorudan gne na ve toza mruz kalan meknlarda Yazcnn ba basma esnasnda yksek sya ulayor. Bu yzden ltfen dokunmadan nce ksa Tally Dascom DT-330 User Guide V1.0 TRADEMARK ACKNOWLEDGEMENTS IBM is a trademark of International Business Machines Corporation. EPSON is a trademark of Epson America Incorporated. DEC is a trademark of Digital Equipment Corporation. Centronics is a trademark of Centronics Data Computer Corporation. DOS is a trademark of Microsoft Corporation. SAP is a trademark of SAP AG. Windows, Windows 7,Windows 8,Windows 10, Windows 95, Windows 98, Windows NT, Windows 2000, Windows 2003/2008/2013 Server, Windows XP and Windows Vista are trademarks of Microsoft Corporation. All other product names and company names appearing in this manual are the registered trademarks or trademarks of the individual companies. Tally Dascom DT-330 User Guide V1.0 About This Manual This manual provides information to operators of the DT-330 to describe basic operations to enable safe and correct use of the printer. Symbols Description The symbols in this manual are identified by their level of importance, as defined below. Read the following carefully before handling the product. CAUTION: Provides information that must be observed to prevent damage to the equipment or loss of date. NOTE: Advises you of information that is essential to complete a task. Tally Dascom DT-330 User Guide V1.0 TABLE OF CONTENTS 1 PRODUCT OVERVIEW...................................................................................................................................................1 1.1 Features................................................................................................................................................................. 1 1.2 Printer Specification.............................................................................................................................................. 2 1.3 Paper Specification................................................................................................................................................ 4 1.3.1 Roll Paper........................................................................................................................................................4 1.3.2 Black Mark Paper............................................................................................................................................4 1.3.3 Notes...............................................................................................................................................................4 1.4 Printing and Cutting Positions............................................................................................................................... 5 1.4.1 Printable Area.................................................................................................................................................5 1.4.2 Cutting Positions.............................................................................................................................................6 1.5 External Dimension and Weight............................................................................................................................7 1.6 Unpacking.............................................................................................................................................................. 8 1.7 Product Configurations..........................................................................................................................................9 1.8 Part Names and Functions.................................................................................................................................. 10 1.8.1 Power Switch................................................................................................................................................ 11 1.8.2 Control Panel................................................................................................................................................ 11 1.8.3 LED Indications............................................................................................................................................. 12 2 SETUP..........................................................................................................................................................................13 2.1 Flow of Setup.......................................................................................................................................................13 2.2 Placing the Printer............................................................................................................................................... 13 2.3 Attaching Power...................................................................................................................................................15 2.4 Adjusting the Paper Near-End Sensor.................................................................................................................16 2.5 Loading Paper Roll............................................................................................................................................... 17 2.5.1 Loading 83mm Media...................................................................................................................................17 2.5.2 Loading 80mm/76mm/70mm/58mm Media.............................................................................................. 19 2.6 Connecting to Computer..................................................................................................................................... 21 2.6.1 Connection Cable Requirement................................................................................................................... 21 2.6.2 Connecting USB Interface.............................................................................................................................22 2.6.3 Connecting Cash Drawer Interface (Option)................................................................................................22 2.6.4 Connecting Serial Interface (Option)............................................................................................................23 2.6.5 Connecting Parallel Interface (Option).........................................................................................................23 2.6.6 Connecting Ethernet Interface (Option)...................................................................................................... 24 2.6.7 Connecting Wi-Fi Interface (Option)............................................................................................................ 24 2.7 Installing Kits........................................................................................................................................................25 3 SOFTWARE SETUP...................................................................................................................................................... 26 3.1 Installing Windows Driver....................................................................................................................................26 3.2 Installing Config Tool............................................................................................................................................29 3.3 Setting the printer parameters via Config tool................................................................................................... 31 3.4 Upgrading the Firmware via Config tool............................................................................................................. 35 4 SETTING/CHECKING MODES......................................................................................................................................37 4.1 Print a Parameter Setting Page (Self-test Page)..................................................................................................37 5 TROUBLESHOOTING...................................................................................................................................................38 5.1 Error Status.......................................................................................................................................................... 38 5.2 Possible Issues While Printing............................................................................................................................. 39 Tally Dascom DT-330 User Guide V1.0 5.3 Possible Issues While Cutting..............................................................................................................................39 5.4 Removing Jammed Paper....................................................................................................................................40 5.5 Cleaning Thermal Head....................................................................................................................................... 41 5.6 Maintenance........................................................................................................................................................41 6 COMMUNICATION INTERFACES SPECIFICATIONS.....................................................................................................42 6.1 USB Interface....................................................................................................................................................... 42 6.2 Cash Drawer Interface......................................................................................................................................... 42 6.3 Wi-Fi Interface..................................................................................................................................................... 43 6.4 Ethernet Interface................................................................................................................................................43 6.5 Serial Interface.....................................................................................................................................................43 6.6 Parallel Interface..................................................................................................................................................44 6.7 Power Socket....................................................................................................................................................... 45 7 PRINTING CONTROL COMMAND SETS......................................................................................................................46 APPENDIX I WI-FI CONNECTION (OPTION).................................................................................................................. 48 APPENDIX II FCC STATEMENT....................................................................................................................................... 52 APPENDIX III DASCOM EPRESENTATIVES..................................................................................................................... 53 Tally Dascom DT-330 User Guide V1.0 1 PRODUCT OVERVIEW Tally Dascom DT-330 offers high-speed receipt printing for a wide range of terminal equipment including data, POS, and kitchen terminals. With extensive features, it can be used in a wide range of applications such as food service, retail and grocery. DT-330 can be desktop or wall-mounted and comes with USB, RS-232 serial, Centronics parallel, Ethernet, Wi-Fi or Cash drawer interfaces. Printer drivers included are: Windows XP, Windows 7, Windows 8, Windows10 (32 and 64 bit). 1.1 Features High speed printing (300 mm/s maximum). Drop-in paper roll mechanism facilitating easy paper handling and head cleaning. Wide range of connectivity. The USB interface is standard interface. Serial/parallel/Ethernet/
Wi-Fi/cash drawer are optional interfaces. Various interface choices suit all needs. Versatile roll capacity with ability to use 83mm, 80mm, 76mm, 70mm and 58mm wide paper rolls. Command protocol is based on the ESC/POS Proprietary Command System. 1 Tally Dascom DT-330 User Guide V1.0 1.2 Printer Specification Print Parameter Print method Resolution Print width Interface Print density Page Mode Memory Receive Buffer RAM Flash Characters per line Chinese Character 1D 2D Sensors Fonts Barcode Graphics Detect Function Power Consumption Direct thermal line printing 203DPI, 8dots/mm Max. 80mm(640dots) StandardUSB interface OptionalRS232, Parallel, Ethernet, Wi-Fi, Cash drawer interface The density can be adjusted to 4 levels, matching different print speeds. Supported 8Mbytes 16Mbytes 256Kbytes Special Font A53 cpl Special Font B71 cpl GB18030 2424 UPC-A, UPC-E, EAN8, EAN13, CODE39, ITF, CODEBAR, CODE128, CODE32 PDR417, QR code Supports several bitmap densities and download image printing. (Maximum size of each bitmap is 64kB. The total size of memory is 256K.) Paper End, Paper Near End, Paper Jam and Cover Open sensors. 36W (operation) 7W (standby) External power adapter Power Supply Input AC 100V-240V, 1.8A, 50-60Hz Output Emulation DC 24V5%, 3.0A, A-1009-3P interface ESC/POS compatible command set Operating condition 540/1090RH Storage condition
-2060/1095RH Physical Spec. Dimension 142192150 (WDH mm) Colour Weight Black Approx. 1.47kg 2 Tally Dascom DT-330 User Guide V1.0 Optional Kit Standard Kit Reliability Driver Certification Splash cover, Mounting plate Interface cover Print head lifetime 150km MTBF 360, 000 hours Cutter lifetime 2,000,000 times MCBF 52,000,000 lines Windows XP/7/8/10 (32& 64bit) UL, FCC, CE 3 Tally Dascom DT-330 1.3 Paper Specification 1.3.1 Roll Paper User Guide V1.0 Paper type Form Size Roll paper diameter Core diameter Take-up roll paper width 82.50.5mm Paper width Specified thermal paper Roll paper 83mm maximum 13mm minimum 82.5 0.5mm, 800.5 mm, 760.5mm, 69.50.5 mm, 580.5 mm 0.065mm ~ 0.090mm Paper thickness CAUTION The remaining amount of the roll paper when a roll paper near-end is detected differs depending on the spool type. 1.3.2 Black Mark Paper When black mark paper is used, the printing position of the black mark paper must be located on the front surface. The reflectivity of the black mark should be less than 15%, while the reflectivity of the rest of the printing paper should be greater than 85%. The area between 2 black marks should be blank. The size of the black mark shall meet the requirements as shown below. P a p e r E j e c t D i r e c t i o n Print surface 5mm<L1 (the width of the black mark) <10mm L2(the length of the black mark) >12mm 20mm<L3(the distance between 2 black marks) <500mm 1.3.3 Notes Please use the recommended thermal paper or same quality paper, otherwise it will influence the printing quality and decrease the thermal printer head life. Dont stick the paper on the roll paper core. If the thermal paper is polluted by chemical or oil, the thermal paper heat sensibility decreases, which will influence the printing quality. Dont use finger nail or hard articles to touch the surface of thermal paper, otherwise it will cause color fading. When the environment temperature is higher than 70C, the thermal paper color will fade, so pay attention to the influence of temperature, humidity and sunlight. 4 Tally Dascom DT-330 1.4 Printing and Cutting Positions 1.4.1 Printable Area User Guide V1.0 83 mm paper width printing The printable area of a paper with width of 82.5 0.5 mm is 79.5 0.5 mm (640 dots) and the spaces on the right and left sides are approximately 1.2 mm. 82.5 0.5 mm {3.24 0.02"}
0.124 0.05 mm {0.0048 0.0002"}
79.5 0.5 mm {3.12 0.008"}
1.2 mm {0.15}
1.2mm {0.15}
All the numeric values are typical. 58 mm paper width printing The printable area of a paper with width of 57.5 0.5 mm is 50.8 0.2 mm (576 dots) and the spaces on the right and left sides are approximately 3.7 mm. 57.5 0.5 mm {2.26 0.02"}
0.141 0.05 mm {0.056 0.002"}
50.8 0.2 mm {2.00 0.008"}
3.7 0.2 mm {0.15 0.079"}
3.0 0.2 mm {0.12 0.079"}
All the numeric values are typical. 5 Tally Dascom DT-330 1.4.2 Cutting Positions User Guide V1.0 Last line of a previous receipt Manual-cutter position Approx. 29 Auto-cutter blade position Approx. 15 Center of the print dotline Paper feed direction
[Units: mm (All the numeric values are typical.)]
6 Tally Dascom DT-330 1.5 External Dimension and Weight Width: Approximately 142 mm Depth: Approximately 192 mm Height: Approximately 150 mm Weight: Approx. 1.47kg (excluding power adapter) User Guide V1.0 7 Tally Dascom DT-330 User Guide V1.0 1.6 Unpacking When you receive the printer, please check for possible shipping damage:
1. Inspect the outside of both the carton box and the printer for possible damage. 2. Open the top cover of the printer to see if the media compartments are in order. If you discover shipping damage upon inspection:
Immediately notify the shipping company and file a damage report. Keep all packaging material for shipping company inspection. Notify your authorized dealer. The package contents vary with different customized order requirements. 8 Tally Dascom DT-330 User Guide V1.0 Shipping List Item Printer Interface Cable Cover Power Adapter Power Cord Roll Paper - Test Graphic Installation Guide CD Spacer QTY. 1 unit 1 piece 1 piece 1 piece 1 piece 1 piece 1 piece 2 piece Remark including User Guide, Graphic Installation Guide and Driver 1.7 Product Configurations Interfaces Cutting Sensor Product USB Serial Parallel Ethernet Wi-Fi Cash drawer T e a r C u t t e r M a r k l B a c k DT-330 O O O O O O Remarks: denotes standard component. O denotes optional component. 9 Tally Dascom DT-330 User Guide V1.0 1.8 Part Names and Functions Printer Cover NOTE:
Please pay attention to the tear bar when you use. Control Panel Cover Open Button Cutter Cover Power Switch Component Function Printer Cover Control Panel Power Switch Cutter Cover Open the cover when loading roll paper. Shows printer status. To power printer ON or OFF. To protect the auto-cutter and to clear paper jam at the cutter. Cover Open Button Press down to open the Printer Cover. 10 Tally Dascom DT-330 User Guide V1.0 1.8.1 Power Switch Turn the printer on or off. The marks on the switch: (O: OFF / | : ON) Before turning on the printer, be sure to check that the AC adapter is connected to the power supply. 1.8.2 Control Panel POWER LED PAPER LED ERROR LED FEED key LED Power LED Lights when the power supply is on. Goes out when the power supply is turned off. Paper LED Off when there is a sufficient amount of roll paper remaining. Lights or Flashes when there is no more roll paper or there is little remaining. Error LED Lights or Flashes when an error occurs. Please power off the printer and refer to Chapter 5.1 Error Status. Feed Key Pressing this key once feeds the roll paper by one line. Holding this button down feeds the roll paper continuously. 11 Tally Dascom DT-330 User Guide V1.0 1.8.3 LED Indications Description Printer Cover is open Roll paper is sufficient Roll paper end Roll paper near end Black mark is not detected Cutter jam Print head overheated POWER On On On On On On Flash PAPER On Off On Flash Off Off Off ERROR BEEPER No beep Off Off No beep No beep Off No beep Off Flash No beep No beep On Flash No beep 12 Tally Dascom DT-330 User Guide V1.0 2.1 Flow of Setup 2 SETUP 1. Placing the Printer 2. Loading Paper Roll 3. Attaching Power 4. Printing Self-test 5. Adjusting the Paper Near-End Sensor 6. Connecting the Printer to the Host Computer 2.2 Placing the Printer You can install this printer horizontally. With an optional mounting plate, you can also attach the printer to a wall. Its recommended that the printer should be installed at a horizontal surface. Horizontal Installation You can install this printer horizontally. Place the printer on a solid, flat, stable surface; ensure the printer is placed in a stable position and there is easy access for users to the control panel and roll paper holder. Also ensure there is enough space for sufficient ventilation and for the printout. Important Notes on Horizontal Installation:
The printer should be installed at a flat and steady place. The angle of inclination should not exceed 10(paper feed direction) if tilt install printer, it does not allow to tilt by other direction. Keep printer far away from water sources. Avoid placing the printer near vibration sources. 13 Tally Dascom DT-330 User Guide V1.0 Ensure the grounding connect of the printer is safe. When the printer is at operation and maintenance, it is recommended to retain the enough space to ensure the printer can work in reliability and ease of operation. Vertical Installation Vertical Installation Steps:
You need to perform the follow tasks to install the printer on a wall. 1. Mount the plate on the lower housing of the printer with screws. 2. Align the positioning holes of the mounting plate and plug into the fixed screws on the wall. Please set Paper Near-End Sensor to 4~6 when the printer is vertically installed. 14 Tally Dascom DT-330 User Guide V1.0 2.3 Attaching Power Checking the voltage of the power adapter Before you connect the power adapter to the power socket, check if the voltage is correct. If you connect the power adapter to power with incorrect voltage this may result in electrical damage to adapter and printer. 1. Make sure the printer and the computer are powered off. 2. Connect the power cord to the power adapter. 3. Connect the power adapter to the power socket at the rear of the printer. 4. Ensure the power cord is securely connected. Connect the power cord plug to a main socket. 1) Please use the recommended power adapter or equivalent products. 2) When disconnecting the AC adapter plug, hand-held plug connector housing, to avoid the pulling on the cable with force. 3) Avoid pulling the power adapter cable, otherwise it will damage the cables, causing fire and shock. 4) Avoid placing the power adapter around a heating device, otherwise the cable may melt, causing fire and shock. 5) supply of the printer power adapter. If you do not use the printer over a long time, disconnect the power 15 Tally Dascom DT-330 User Guide V1.0 2.4 Adjusting the Paper Near-End Sensor Adjust the Paper Near-End Sensor to suit the diameter of the roll paper used and the placing direction the printer is installed. Follow the steps below to adjust the paper roll near-end detector. 1. Open the paper roll cover, and remove the paper roll. 2. You will see a lever inside as shown below. Paper Near-End Lever 3. Adjust the lever according to your need. Adjustments position Remaining amount of paper
(outer diameter: mm) 1 (Minimum) 2 3 4 5 6 (Maximum) Approx. 26 Approx. 27 Approx. 28 Approx. 30 Approx. 32 Approx. 33 16 Tally Dascom DT-330 User Guide V1.0 2.5 Loading Paper Roll Confirm the type of paper used by the printer before printing. The default paper type is specified thermal paper. 2.5.1 Loading 83mm Media 1. Press the cover open button to open the cover. 2. Remove the used roll paper core, if any. 3. Insert the paper roll with its print area facing down as shown below. 17 Tally Dascom DT-330 User Guide V1.0 4. Install the media in the correct direction. 5. Pull out some roll paper, and close the cover. Make sure the paper inside is tight enough, otherwise it will jam the paper. 6. Tear off the paper with the manual cutter. 18 Tally Dascom DT-330 User Guide V1.0 2.5.2 Loading 80mm/76mm/70mm/58mm Media The printer is initially set to print on 83 mm width paper and you can change the printer to print on different width paper (80mm/76mm/70mm/58mm) by installing the roll paper spacer and changing the paper width setting with customized value. Follow the steps below to install the roll paper spacer. 1. Open the paper roll cover. 2. Hold the spacer and carefully insert it into the specified position as shown below. Spacer 19 Tally Dascom DT-330 User Guide V1.0 When loading 80mm/76mm/70mm media, 1 spacer is required. When loading 58mm media, 2 spacers are required. 20 Tally Dascom DT-330 User Guide V1.0 2.6 Connecting to Computer NOTE!
Be sure to install the driver before connecting the printer to the host computer. Before installing, disconnect the power from the printer. Even when the power switch is off, voltage is still present at some points on the circuit board. Changing components while the power is connected can cause damage to the interface board and the printer. Modular Interfaces
(Parallel/Serial/Ethernet/WIFI/Cash drawer Power Socket USB Interface Component Function Modular Interface Connects optional interface (Serial I/F, Parallel I/F,
(optional) Ethernet I/F, Wi-Fi I/F or Cash drawer I/F) to the host. USB Interface (standard) Connects USB interface cable to the host. Power Socket Connects power supply to the printer. 2.6.1 Connection Cable Requirement Connection cable must be shielded and comply with the following requirements:
Connection Type USB Serial Parallel Ethernet Specifications USB 1.1/2.0 compatible RS232 IEEE 1284.4 10 Base-T/100 Base-TX compatible 21 Tally Dascom DT-330 User Guide V1.0 2.6.2 Connecting USB Interface CAUTION!
Be careful not to insert the USB interface cable into the cash drawer kick-out connector. 2.6.3 Connecting Cash Drawer Interface (Option) 1. Confirm that the power switch is OFF. 2. Confirm the top and button of the cash drawer cable connector and insert it into the cash drawer kick-out connector at the back of the printer. 3. Connect the ground wire of the cash drawer to the body of the printer and screw it. CAUTION!
DO NOT connect any other device than the specified cash drawer to the cash drawer kick-out connector. (Do NOT connect a telephone line either.) 22 Tally Dascom DT-330 User Guide V1.0 2.6.4 Connecting Serial Interface (Option) Insert the interface cable connector firmly into the interface connector on the connector 1. panel. 2. When using the connectors equipped with screws, tighten them to secure the connectors firmly. 3. Connect the other end of the interface cable to the host computer. 2.6.5 Connecting Parallel Interface (Option) Insert the interface cable connector firmly into the interface connector on the connector 1. panel. 2. Press down the clips on either side of the connector to lock it in place. 3. Connect the other end of the interface cable to the host computer. 23 Tally Dascom DT-330 User Guide V1.0 2.6.6 Connecting Ethernet Interface (Option) 2.6.7 Connecting Wi-Fi Interface (Option) Please refer to APPENDIX I for more instructions. 24 Tally Dascom DT-330 User Guide V1.0 2.7 Installing Kits Interface Cover (standard Kit) Adjust the relative positions between interface cover and the printer, and push the interface cover as the arrow shows below. Fix it by screwing. Interface Cover Splash Cover (optional kit) Slip the fixed hooks on both sides of splash cover into the mounting hole on the printer, and close the splash cover. Splash Cover Mounting Hole 25 Tally Dascom DT-330 User Guide V1.0 3 SOFTWARE SETUP 3.1 Installing Windows Driver Switch off the printer before running the printer driver setup. Your printer CD-ROM comes with Windows drivers. Go to the related folder and run the driver setup installer. If the Software Pack CD-ROM is not available, you can download the latest driver from the Tally Dascom Web Site: http://www.dascom.com 1. Double click the driver. You will see the screen as below. Click Next to continue. 26 Tally Dascom DT-330 User Guide V1.0 2. Choose the printer model name. Click Next to continue. 3. Choose the desired port (USB001 for USB port, com1 for serial port and LPT1 for parallel port). Click Next to continue. 27 Tally Dascom DT-330 User Guide V1.0 4. Click Finish to finish the installation process successfully. 28 Tally Dascom DT-330 User Guide V1.0 3.2 Installing Config Tool Your printer CD-ROM comes with Tally Dascom Setup Tool. Go to the related folder and run the setup installer. 1. Select whether to create a shortcut. Click Next to continue. 2. Click Install to continue. 29 Tally Dascom DT-330 User Guide V1.0 3. Click Finish to finish the installation process successfully. 30 Tally Dascom DT-330 User Guide V1.0 3.3 Setting the printer parameters via Config tool 1Run Tally Dascom Printer Config Tool. 2Click Connection Config. Select the port at the upper right corner. Please note that only USB Port is available for DT-330. 31 Tally Dascom DT-330 User Guide V1.0 3Click Connect. Printer info will be shown at the upper left corner. 4Click Setting in the Config Tool menu, you can change the parameters as shown below. 32 Tally Dascom DT-330 User Guide V1.0 System Setup Parameter Energy Saving Default 10min Darkness Print Mode Emulation Left Margin 2 Quality Priority ESC/POS 0.0mm Selectable parameters and Annotation the time before entering energy-saving Select mode without any data communication and button action, or directly cancel the energy-saving mode. Off 1 min 2 min 5 min 10 min Selectable range is 1~4. Quality PriorityThe print quality is best, while the print speed will be lowered. Speed PriorityThe print speed is fastest, while the print quality will be decreased. ESC/POS Selectable range is 0 ~ 80mm. Device Configuration Parameter Black mark Option BM To First Line Offset BM To Tear Offset Cutter Option Default Disable
-4.0mm 90.0mm Partial Cut Selectable parameters and Annotation Disable Enable Selectable range is -4 ~ 50mm. Selectable range is -18 ~ 150mm. Disable Full Cut Partial Cut 5 Save the parameters and click at the upper right corner to return to the menu. Click Disconnect, the printer will restart to execute the new parameters. 33 Tally Dascom DT-330 User Guide V1.0 Button ( Save, Reset, Read Settings, Import and Export) function Save Reset Read Settings Import Export This stores the changed parameter values to the printer memory. The printer notifies with a sound. This restores the printer with factory parameter settings. A message box will pop up for re-confirm. The printer notifies with a sound after your confirmation. This retrieves the parameter values from the printer memory. If you have changed some values without saving, a warning message will pop up to notify some values have been changed but not saved. The Confirm (O) button saves the changes. The Cancel (C) button ignores the new changes and proceeds to retrieve parameter values from the printer memory. This imports an external .cfg file to simplify the parameter setting process. 1A click on this Import button pops up the Open dialog box. Browse the folder to locate the desired .cfg file. Click the Open button on the lower right corner to import this .cfg file. 2 The import of parameters fails if Printer mis-match message is displayed. The parameter imported cannot be applied to your printer, because the .cfg file is not applicable to DT-330. This exports all the parameter values on this printer to a .cfg file. Saving this .cfg file to a flash-drive ease the work of setting multiple printers with identical parameter values. A click on this Export button pops up the Save dialog box. Browse to locate the desired folder then input a name with .cfg extension. Click the Save button on the lower right corner to store this .cfg file. When Export successfully! is displayed, click the Confirm(Obutton. 34 Tally Dascom DT-330 User Guide V1.0 3.4 Upgrading the Firmware via Config tool 1 Run Tally Dascom Printer Config Tool. Below will be shown when the connection is successful. 2Click Upgrade in the Config Tool menu. Locate the Firmware file by clicking Browse. 35 Tally Dascom DT-330 User Guide V1.0 3 Click Start. A message box pops up to ask for confirmation. Click Confirm to start the upgrade process. 4When the progress bar reaches 100%the upgrade process is completed and the printer will be restarted. 36 Tally Dascom DT-330 User Guide V1.0 4 SETTING/CHECKING MODES 4.1 Print a Parameter Setting Page (Self-test Page) Before you connect the printer to the computer, make sure that the printer is in proper working order. Follow the steps below to run Self-test mode. 1. Make sure the media is properly loaded, the top cover of the printer is closed and the printer is power off. 2. Turn on the printer. 3. Keep pressing the FEED button for 4 sec, the printer starts printing a self-test page. 37 Tally Dascom DT-330 User Guide V1.0 5 TROUBLESHOOTING Your printer is extremely reliable, but occasionally problems may occur. This chapter provides information on some of the common problems you may encounter and how you may solve them. If you encounter problems that you cannot resolve, contact your dealer for assistance. Read the following instructions before maintenance and avoid incorrect operation, so as to prevent injury to you and damage to the printer. 5.1 Error Status LED indications Problem Error LED Paper LED Solution Print head is overheated. Print head is lifted. Paper end Paper near end Cutter jam Printer cover is open. Incorrect power connection Power switch is OFF. PCB board is damaged. flash off off off on off off off off Turn the printer off and wait some minutes before you resume. Press the print head down. Reload the paper roll. The roll paper is near end, the printer can work normally, procure new paper and load it when paper is used up. Reload the roll paper. Close the Printer Cover. Check the power supply cable connections and the power outlet, and correct them. Turn on the power switch. Contact your dealer for assistance. off on on flash off on off off off 38 Tally Dascom DT-330 User Guide V1.0 5.2 Possible Issues While Printing Trouble Colored stripe in the paper Blurred or spot printing Paper Jam Vertical dot line missing Potential Problem Paper near end Incorrect roll paper installation Poor paper quality Dirty thermal head or print roller Low Print density Paper stuck Dirty thermal head or print roller Solution Install a new roll of paper. Install the paper roll correctly. Use recommended thermal roll paper. Clean the thermal head or print roller. Increase the print density level. Open the printer cover, check the paper path and remove jammed paper. Clean the thermal head or print roller. Thermal head damaged Contact your dealer for assistance. 5.3 Possible Issues While Cutting Trouble Cutter jam, the movable cutter cannot move back Insufficient cutting Potential Problem Cutter abrasion, insufficient cutting Worn gear and worn wheel abrasion Solution Replace the cutter Replace the worn gear and worn wheel Motor burnt Paper scraps Replace the motor Clean the paper scraps on the transmission system Cutter edge abrasion, paper too thick Thermal printer head over heat Paper Jam Driving too fast Wrong paper feeding position Replace the cutter Reduce the density of printing Reduce the printer speed to the limit of thermal printer head Put the paper parallel with paper mount and insert into the space between the platen roller and the thermal print head 39 Tally Dascom DT-330 User Guide V1.0 5.4 Removing Jammed Paper Print head may be hot, please do not touch!
Turn off the printer. Press the cover open button to open the printer cover. Remove the jammed paper, and close the printer cover. If the paper is jammed at the cutter, please do not open the printer cover. Lift up the cutter cover instead. (As shown in Picture 1) Turn the knob until the cutter blade returns to the normal position. (As shown in Picture 2) Close the cutter cover. Picture 1 Picture 2 40 Tally Dascom DT-330 User Guide V1.0 5.5 Cleaning Thermal Head After printing, the thermal print head becomes very hot. Be careful not to touch it and to let it cool before you clean it. fingers or any hard object. Prevent the damage to the thermal print head by touching it with your Turn off the printer, open the printer cover, and clean the thermal elements of the print head with a cotton swab moistened with an alcohol solvent (ethanol, methanol, or isopropyl alcohol). It is recommended to clean the print head every 3 months to ensure the print quality. 5.6 Maintenance This printer is toughly built to meet heavy load without regular maintenance. However regular cleaning can extend the operating life of the printer. It is recommended to clean the printer every 6 months or 300 operating hours. Turn off the power and unplug the power cord before cleaning. Pick up paper debris by a pair of tweezers. Clean up the dust inside by a brush or compact vacuum cleaner. Clean up the dirt inside with a clean cloth. Clean the platen with a soft cloth. Avoid damages to or loosing the cable winding and components inside. Avoid metallic objects falling into the electric areas to cause short-circuit. 41 Tally Dascom DT-330 User Guide V1.0 6 COMMUNICATION INTERFACES SPECIFICATIONS Power socket and USB interface are standard interfaces for the printer. Serial interface, Parallel interface, Ethernet interface, Wi-Fi interface and Cash drawer interface are optional interfaces for the printer. 6.1 USB Interface USB interface pin assignment PIN No. 1 2 3 4 Description VBUS D-
D+
GND USB interface connector diagram Classic wire color Red White Green Black 6.2 Cash Drawer Interface Cash Drawer interface pin assignment Cash drawer interface supports DC24V, RJ-11 6P type socket. Direction Pin. No. 1 2 3 4 5 6 Description
-
Frame Ground Drawer kick-out drive signal 1 Output Drawer open/close signal
+24V Drawer kick-out drive signal 2 Output GND Input
-
-
Cash Drawer interface connector diagram 1 6 42 Tally Dascom DT-330 User Guide V1.0 6.3 Wi-Fi Interface Wi-Fi interface supports 2.4 GHz, IEEE Std. 802.11b/g standard. 6.4 Ethernet Interface Ethernet interface pin assignment Pin. No. 1 2 3 4 5 6 7 8 Name TX+
TX-
RX+
n/c n/c RX-
n/c n/c Description Tranceive Data+
Data-
Receive Data+
Not connected Not connected Receive Data-
Not connected Not connected Ethernet interface connector diagram 6.5 Serial Interface Serial interface pin assignment Serial interface compatible with RS-232 standard, with 25 pin (D hole type) socket. PIN No. PIN 1 PIN 2 PIN 3 PIN 4 PIN 5 PIN 6 PIN 7 Description Frame Ground TXD RXD RTS Unconnected DSR Signal Ground 43 Tally Dascom DT-330 User Guide V1.0 PIN 8~19 PIN 20 PIN 21~25 Unconnected DTR Unconnected User can view the setting of interface via printing configuration sample. The default setting of serial interface is as follow, 38400 bps (baud rates), 8 bit (data bit), 1 bit (stop bit), no parity, support DTR/DSR handshaking protocol. Serial interface connector diagram 6.6 Parallel Interface Parallel interface pin assignment Parallel interface with 36 pin CENTRONICS socket. Pin No. Signal From 1 2 3 4 5 6 7 8 9 10 11 12 13 14 H H H H H H H H H P P P Description Strobe Signal; Data latch pulse, latch the data to the printer at the rising edge of the negative pulse. Data 0 (The lowest bit) Data 1 Data 2 Data 3 Data 4 Data 5 Data 6 Data 7 (The highest bit) ACK Signal; Printer response signal, indicates that the printer has received a Data byte. Busy Signal; The printer is busy; High level indicates that the printer cant receive data. PE Signal; Paper end signal; High level indicates that the printer is out of paper. Unconnected Unconnected 44 Tally Dascom DT-330 User Guide V1.0 15 16 17 18 Unconnected Logic Ground Frame Ground, separated from logic ground. Unconnected 19~30 Logic Ground 31 32 33 34~35 36 P Unconnected Printer error signal. Low level indicates that an error occurs in the printer. It will come with paper end. Logic Ground Unconnected Unconnected H indicates that signal comes from Host computer; P indicates that signal comes from Printer. Parallel interface connector diagram 6.7 Power Socket External Power Adapter Input AC 100V-240V, 1.8A, 50-60Hz OutputDC 24V5%, 3.0A, A-1009-3P interface Power Socket pin assignment Pin Number Signal Name 1 2 3 SHELL
+24 V GND Not Connected Frame Ground Power Socket connector diagram 45 Tally Dascom DT-330 User Guide V1.0 7 PRINTING CONTROL COMMAND SETS Compatible with ESC/POS command set Support NV image and page mode printing List of Commands Command Function HT LF FF CR ESC FF ESC SP ESC !
ESC $
ESC ESC ESC 2 ESC 3 ESC @
ESC D ESC E ESC G ESC J ESC L ESC M ESC S ESC V ESC W ESC \
ESC a ESC d GS !
GS $
Horizontal tab Print and line feed Print and return to standard mode (in page mode) Print and carriage return Print data in page mode Set right-side character spacing Select print mode(s) Set absolute print position Select bit-image mode Turn underline mode on/off Select default line spacing Set line spacing Initialize printer Set horizontal tab positions Turn emphasized mode on/off Turn double-strike mode on/off Print and feed paper Select page mode Select character font Select standard mode Turn 90 degrees clockwise rotation mode on/off Set print area in page mode Set relative print position Select justification Print and feed n lines Select character size Set absolute vertical print position in page mode 46 Tally Dascom DT-330 User Guide V1.0 Set up and print symbol PDF417: Transmit the size information of the PDF417: Print the symbol data in the symbol PDF417: Store the data in the symbol storage PDF417: Set the number of columns in the data
<Function 065>
region.
<Function 066> PDF417: Set the number of rows.
<Function 067> PDF417: Set the width of the module.
<Function 068> PDF417: Set the row height.
<Function 069> PDF417: Set the error correction level.
<Function 070> PDF417: Select the options.
<Function 080>
area.
<Function 081>
storage area.
<Function 082>
symbol data in the symbol storage area.
<Function 167> QR Code: Set the size of module.
<Function 169> QR Code: Select the error correction level.
<Function 180> QR Code: Store the data in the symbol storage area.
<Function 181> QR Code: Print the symbol data in the symbol storage area.
<Function 182> QR Code: Transmit the size information of the symbol data in the symbol storage area. Define downloaded bit image Turn white/black reverse print mode on/off Select print position of HRI characters Set left margin Set unit for horizontal and vertical movement Set print area width Set relative vertical print position in page mode Select font for HRI characters Set bar code height Print bar code Set bar code width Print raster bit image GS ( k GS GS B GS H GS L GS P x y GS W GS \
GS f GS h GS k GS w GS v 0 47 Tally Dascom DT-330 APPENDIX I Wi-Fi CONNECTION (OPTION) User Guide V1.0 If your printer connected to the computer with Wireless Ethernet, there are two kinds of modes:
AP mode and STA mode. AP mode point to the network. AP means Access Point. When the printer is working under AP mode, it works as an access How to setup before printing:
1The PC should be installed with WiFi adapter. 2Search for WiFiPrinter and connect it. 3Add the new port in the driver. Click Start Devices and Printers, right click on the DT-330 Printer Driver, and then click Printer Properties. You will see the screen as below. Click Ports Add Port. 48 Tally Dascom DT-330 User Guide V1.0 Select Standard TCP/IP Port, and click New Port, then click Next to continue. Enter IP address and port name (Default:192.168.0.7). Then click Next to continue. 49 Tally Dascom DT-330 User Guide V1.0 After adding the new port, apply it for printing and finish the process. STA means Station mode. When the printer is working under STA mode, it works as a STA mode wireless terminal device. How to setup before printing:
1The PC should be installed with WiFi adapter. 2Connect the printer with the router, and obtain the IP address assigned by the router. Run cmd commandenter ipconfig in the Virtual DOS window. IP address will be shown. 50 Tally Dascom DT-330 User Guide V1.0 3Run Tally Dascom Printer Config Tool. Enter the IP address under WiFi setup section. 4After setting, click Disconnect to restart the printer. 5Add the new port in the driver (same process as AP mode, IP address should be the same one obtained in step 2 ). 51 Tally Dascom DT-330 APPENDIX II FCC STATEMENT User Guide V1.0 1. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
1) This device may not cause harmful interference. 2) This device must accept any interference received, including interference that may cause undesired operation. 2. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Re-orientate or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. 3.Radiation Exposure Statement This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. 52 APPENDIX III DASCOM EPRESENTATIVES GERMANY DASCOM Europe GmbH Heuweg 3 D-89079 Ulm Deutschland Phone: +49 (0) 731 2075 0 Fax: +49 (0) 731 2075 100 www.dascom.com AMERICAS DASCOM Americas LLC 34 Lakeview Court, Verona, VA 24482 USA Phone:+1 (877) 434 13 77 Fax: +1 (540) 242 7221 www.dascom.com FRANCE DASCOM Europe GmbH 117 Avenue Victor Hugo 92100 Boulogne-Billancourt France Phone: +33 (1) 73 02 51 98 www.dascom.com SINGAPORE (ASIA PACIFIC) DASCOM AP Pte Ltd 2 Jurong East Street 21
# 05-42, IMM Building Singapore 609601 Phone: +65 6760 8833 Fax: +65 6760 1066 www.dascom.com UNITED KINGDOM DASCOM GB Ltd Hart House, Priestley Road Basingstoke, Hampshire RG24 9PU, England Phone: +44 (0) 1256 355130 Fax: +44 (0) 1256 481400 www.dascom.com CHINA Jiangmen Dascom Computer Peripherals Co.,Ltd. No.399, Jinxing Road, Jianghai District, Jiangmen City, Guangdong Province, P.R.China www.dascom.com All rights reserved. Translations, reprinting or copying by any means of this manual complete or in part or in any different form requires our explicit approval. We reserve the right to make changes to this manual without notice. All care has been taken to ensure accuracy of information contained in this manual. However, we cannot accept responsibility for any errors or damages resulting from errors or inaccuracies of information herein. 2019 DASCOM 53
1 | label | ID Label/Location Info | 374.89 KiB |
<q 84.00 mm __ |}
Tally Authorized EU representative:
SSS] SS DASCOM Europe GmbH, Heuweg 3, DASCOM 89079 Ulm, Germany Model : DT-330 This device complies with Part 15 of the FCC Rules. Input: DC 24V2221.5A Operation is subject to the following two conditions:
ID Number : 28.XXX.XXXX (1) This device may not cause harmful interference,and
. (2) This device must accept any interference received, Ne ee OX including interference that may cause undesired UCL No.:00 operation. FCC ID : Z7ODT3300 FE CE Le LISTED Manufacturer: Jiangmen Dascom Computer Peripherals Co., Ltd. Product Identity: NVGQ Address: No.399 Jin Xing Road, Jiang Hai District, Control Number: 4WZ6 Jiangmen City,Guang Dong Province, P.R.China WwW OO LY 84.00 mm Authorized EU representative:
DASCOM DASCOM Europe GmbH, Heuweg 3, 89079 Ulm, Germany Model : DT-330 This device complies with Part 15 of the FCC Rules. &
Input: DC 24V2221.5A Operation is subject to the following two conditions: N ID Number : 28.XXX.XXXX (1) This device may not cause harmful interference,and oO 2) This device must accept any interference received, Ser. Number : XXXXXXXXXXXX faa interference eae cue undesired UCL No.:00 operation. FCC ID : Z7ODT3300 3 Fe ce K We 3 LISTED Manufacturer: Jiangmen Dascom Computer Peripherals Co., Ltd. Product Identity: NWGQ Address: No.399 Jin Xing Road, Jiang Hai District, Control Number: 4WZ6 Jiangmen City,Guang Dong Province, P.R.China V
frequency | equipment class | purpose | ||
---|---|---|---|---|
1 | 2019-05-13 | 2412 ~ 2462 | DTS - Digital Transmission System | Original Equipment |
app s | Applicant Information | |||||
---|---|---|---|---|---|---|
1 | Effective |
2019-05-13
|
||||
1 | Applicant's complete, legal business name |
Jiangmen Dascom Computer Peripherals Co.,Ltd.
|
||||
1 | FCC Registration Number (FRN) |
0021247903
|
||||
1 | Physical Address |
No 399,Jin Xing Road,Jiang Hai District
|
||||
1 |
Jiangmen City Guang Dong Province, N/A
|
|||||
1 |
China
|
|||||
app s | TCB Information | |||||
1 | TCB Application Email Address |
a******@compliancetesting.com
|
||||
1 | TCB Scope |
A4: UNII devices & low power transmitters using spread spectrum techniques
|
||||
app s | FCC ID | |||||
1 | Grantee Code |
Z7O
|
||||
1 | Equipment Product Code |
DT3300
|
||||
app s | Person at the applicant's address to receive grant or for contact | |||||
1 | Name |
Y**** H****
|
||||
1 | Title |
Manager
|
||||
1 | Telephone Number |
0750-********
|
||||
1 | Fax Number |
0750-********
|
||||
1 |
1******@qq.com
|
|||||
app s | Technical Contact | |||||
n/a | ||||||
app s | Non Technical Contact | |||||
n/a | ||||||
app s | Confidentiality (long or short term) | |||||
1 | Does this application include a request for confidentiality for any portion(s) of the data contained in this application pursuant to 47 CFR § 0.459 of the Commission Rules?: | Yes | ||||
1 | Long-Term Confidentiality Does this application include a request for confidentiality for any portion(s) of the data contained in this application pursuant to 47 CFR § 0.459 of the Commission Rules?: | No | ||||
if no date is supplied, the release date will be set to 45 calendar days past the date of grant. | ||||||
app s | Cognitive Radio & Software Defined Radio, Class, etc | |||||
1 | Is this application for software defined/cognitive radio authorization? | No | ||||
1 | Equipment Class | DTS - Digital Transmission System | ||||
1 | Description of product as it is marketed: (NOTE: This text will appear below the equipment class on the grant) | Thermal Receipt printer | ||||
1 | Related OET KnowledgeDataBase Inquiry: Is there a KDB inquiry associated with this application? | No | ||||
1 | Modular Equipment Type | Does not apply | ||||
1 | Purpose / Application is for | Original Equipment | ||||
1 | Composite Equipment: Is the equipment in this application a composite device subject to an additional equipment authorization? | No | ||||
1 | Related Equipment: Is the equipment in this application part of a system that operates with, or is marketed with, another device that requires an equipment authorization? | No | ||||
1 | Grant Comments | Power output listed is conducted. The antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other transmitter. End-users and installers must be provided with antenna installation instructions and transmitter operating conditions for satisfying RF exposure compliance. | ||||
1 | Is there an equipment authorization waiver associated with this application? | No | ||||
1 | If there is an equipment authorization waiver associated with this application, has the associated waiver been approved and all information uploaded? | No | ||||
app s | Test Firm Name and Contact Information | |||||
1 | Firm Name |
EST Technology Co., Ltd.
|
||||
1 | Name |
I****** H********
|
||||
1 | Telephone Number |
+86 0******** Extension:
|
||||
1 |
i******@gdest.cn
|
|||||
Equipment Specifications | |||||||||||||||||||||||||||||||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
Line | Rule Parts | Grant Notes | Lower Frequency | Upper Frequency | Power Output | Tolerance | Emission Designator | Microprocessor Number | |||||||||||||||||||||||||||||||||
1 | 1 | 15C | 2412.00000000 | 2462.00000000 | 0.0118000 |
some individual PII (Personally Identifiable Information) available on the public forms may be redacted, original source may include additional details
This product uses the FCC Data API but is not endorsed or certified by the FCC