Wi-Fi Conguration Option I /Via Browser 1. Power Wi-Fi inverter (or Ezlogger Pro WiFi) on;
2. If you are conguring Wi-Fi inverter, make sure the yellow led on front cover is blining;
Preparation 3. Power Wi-Fi router on;
4. Switch on the Wi-Fi of laptop. 5. Fill in the password for your WiFi network. 6. Click "Complete" and the conguration process completes. Add wireless network manually Save success!
Network name (SSID) WiFi-Test Encryption method Encryption algorithm WPA/WPA2-PSK AES Please enter the wireless network password Password (8-63 bytes) hellogoodwe show psk Click "Complete", the current conguration will take eect after restart. If you still need to congure the other pages of infrmation, please go to complete your required conguration. Conguration is completed, you can log on the Management page to restart device by Click on OK button. Note: Case sensitive for SSID and password Please make sure all parameters of wireless network are matched with router, including password. Back Next Conrm to complete?
Back Complete Congure Wireless Network Please make sure all parameters of wireless network are matched with the router, including password. 1. Connect Wi-Fi to "Solar-WiFi" or "Solar-WiFi*"
2. Enter User name: "admin". Password: "admin"
Password: 12345678
(*means the last 8 characters of the inverter serial number) Admin(U):
admin In the following sections, we will use Solar-WiFi instead "Solar-WiFi" and "Solar-WiFi*"
Brwose website: http//10.10.100.253 Password:
Remember the password(R) Access point setting OK CANCEL Friendly Tips Wizard Advanced Management 3. Click "Start Setup"
4. Select Wi-Fi router's SSID and click "Next"
DHCP setting for STA http//10.10.100.253 Note: If Unauthorization Login apperas, please refresh the web browser. Device information Firmware verison MAC address Wireless AP mode SSID IP address Wireless STA mode Router SSID Encryption method Encryption algorithm Router Password 1.6.9.38.2.1.38 60:C5:A8:60:33:E1 Enable Solar-WiFi 10.10.100.253 Disable WiFi_Burn-in WAP / WAP2-PSK AES WiFi_Burn-in Cannot join the network, may be caused by:
router doesnt exist, or signal is too week, or password is incorrect Help: Wizard will help you to complete setting within one mimute. Start Setup Please select your current wireless network:
SSID WIFI Test Sec mode Enc type Channel WAP2-PSK AES 6 RSSI 54%
Note: When RSSI of the selected WiFi Network is lower than 50%, the connection may be unstable, please select other available network or shorten the distance between the device and the router. If your wireless router does not broadcast SSID, please click Next and add a wireless network manually. Back Next Network name (SSID) Encryption mod Encryption algorithm Password (8 to 63 characters) WiFi-Test WPA/WPA2-PSK TKIP/AES 1245678 You can modify the Wi-Fi modules SSID or/and password in the "Advanced" interface. SKIP THIS STEP UNLESS IT IS NECESSARY!
Note: cong the devices parameter under the access point mode. DHCP 192.168.78.2 255.255.255.0 192.168.78.1 0.0.0.0 Save Save Note: After changing the settings, the device must be restarted. Note: The AP "Solar-WiFi" might disappera after inverter connects to WiFi router. Turn o router or do "WiFi Reload" operation via button on inverter if you need connect to Solar-WiFi once again. The Wi-Fi module parameters please refer to The Wi-Fi module parameters please refer to Device information column above. Device information column above. Go to SEMS Portal (www.semsportal.com) or SEMS Portal APP, register and create your Power Station. 01 02 340-00072-06 9. Read the hint before click 10. If it fails, you can "Recong-
11. Follow up the instructions
"OK"
ure" or view "Conguration and try again help"
Option /Via APP (Smart Phone/Pad) Preparation 1. Power Wi-Fi inverter (or Ezlogger Pro WiFi) on;
2. If you are conguring Wi-Fi inverter, make sure the yellow led on front cover is blining;
3. Power Wi-Fi router on;
4. Search for the keyword "SEMS Portal" from Google Play Store or Apple App Store, download and install the latest version of the monitoring software for free. 5. As app keeps updating always, please visit latest version guide doc by http://en.goodwe.com/Public/Home/Wi-Fi Connection Guide.pdf Note: If any problem during conguration, Please refer to the relevant content in the FAQ. Congure Wireless Network 1. Click "Wi-Fi Conguration" in 3. Power on inverter, then click 4. Click "Go into WLAN setting login page
"Next"
interface"
5. Connect to Solar-WiFi
(Password:12345678) back to App 7. Select your Wi-Fi network 8. Enter password, and click
"Set"
2. Or click the third one in tab bar 6. Click "Next"
FAQ (Frequently Asked Questions) Cannot nd Wi-Fi signal of solar-WiFi 1. Make sure inverter is power on and antenna is installed;
2. Move colser to inverter;
3. Restart inverter;
4. Do "WiFi Reload" operation via button on the front cover of inverter. Cannot connect to Solar-WiFi 1. Try password "12345678";
2. Restart inverter;
3. Do "WiFi Reload" operation, and try password "12345678" again. Cannot login webpage of Solar-WiFi 1. Try admin as username and password;
2. Do "WiFi Reload" operation, and try admin/admin again;
3. Repeat step2 again. 4. Conrm the website is http://10.10.100.253 unable to nd the SSID of router on search page 1. Place the wireless router closer to inverter or add a wireless signal simplier. Then restart Wi-Fi at "Management" page. 2. Connect to the network of Wi-Fi and then go to the "Router Conguration"
page. Check the communication channel. If the value is higher than 13, please change it into a value lower than 13. After conguration, the yellow led blinks twice regularly within 1.6 sec. 1. Restart inverter;
2. Connect to Solar-WiFi and login again, check the "SSID", "Security Mode",
"Encryption Type" and "Pass Phrase" is matching with that of Wi-Fi router or not;
3. Connect to Wi-Fi router and login to check if the connection reaches the maximum amount or not, and to check the channel of it uses. 4. Restart Wi-Fi router;
5. Move Wi-Fi router closer to inverter or use a Wi-Fi repeater device. Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment o and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit diferent from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. This device complies with part 15 of the FCC Rules. Operation is subject to the following conditions:
This device may not cause harmful interference. This device must accept any interference received, including interference that may cause undesiredoperation. WARNING 1. This equipment complies with radio frequency (RF) exposure limits adopted by the Federal Communications Commission for an uncontrolled environment. This equipment should be installedand operated with a minimum distance of 20 cm between the radiator and your body. After conguration, the yellow led blinks four times regularly within 2. Changes or modications not expressly approved by the party responsible for compliance could void the authority of the user to operate the 1. Connect to the Wi-Fi router and visit the portal. Check the portal is available or 1.6 sec. not;
2. Restart Wi-Fi router and inverter;
After conguration, the yellow led is steady all the time, but the status of PV station on portal is still oine. Please wait 10 minutes and check the status on the portal again. This module is an accessory of the inverter and only used with the inverter. Do not install the module into other consumer device. The module can work by install the module into the inverter communication port and powering it equipment. Note:
on. 04 Set If you want to set a specic IP to the inverter, switch o DHCP and manually input the IP address, etc. 03 340-00072-06