FCC ID: 2AHGJJMSXL0812-27-1 RC PET PLUSH 2 0 (27MHz remote controller)

RC Plush Animal User Manual Battery installation For Animal Car Remove the screw and open the batteries cover. Insert 3*AAA batteries (1.5V) and close the batteries cover. Put the screw back and lock the batteries cover. For Remote Controller:

Remove the screw and open the batteries cover. Insert 2*AAA batteries (1.5V) and close the batteries cover. Put the screw back and lock the batteries cover. Operation procedure Put the Animal car on the floor and make sure the frequency docking successfully when the car and the controller are turned on. Use the remote controller to control the Animal Car. The animal car will move forward when you press the forward button in left side. The animal car will rotate backward when you press the backward button in right side. Notes:

Please make sure the car and remote controller within 5 meter range. Age Recommendation: 10+ years and adult supervision required. If you do not play the car, you must remove the batteries from both of the remote controller and the car. Packaging includes:

Animal car unit 1pc Remote controller unit 1pc Product dimension:

Animal car unit: 4.6W*3D*6H Remote controller unit: 2.55W*2.65D*0.85H Description:

Remote controller batteries: 2*AAA (1.5V) batteries are not included. Animal car batteries: 3*AAA (1.5V) batteries are not included. Range: 5 meters Duration: about 15mins Suitable for children of 10 years old or above User Manual This device complies with Part 15 of FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference.

(2) This device must accept any interference received, including interference that may cause undesired operation. Warning: Changers or modifications to this unit not expressly approved by the party responsible for the compliance could void the users authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part, 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna. Increase the separation between the equipment the receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. RF Warning statement:

The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction. Conforms to ASTM F963-17

EXHIBIT A - FCC ID LABEL AND LOCATION FCC ID Label FCC ID Label Location Information The label shown shall be permanently affixed at a conspicuous location on the device and be readily visible to the user at the time purchase (Labeling requirements per 2.925)

Address: Unit G, 4/F Kaiser Estate, Phase 2, No. 47-53 Man Yue Si dy \ JM Manufacturing (HK) Ltd. Street, Hung Hom, Kowloon, HongKong Tel: (852) 2770 2712 Fax: (852) 2385 8073 Email: samleung@justen-marks.com.hk FCC Authorization 16/12/2019 FEDERAL COMMUNICATIONS COMMISSIONS Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 Subject: Agent Authorization To whom it may concern:

We,_JM Manufacturing (HK) Ltd, the undersigned, hereby authorize Bay Area Compliance Laboratories Corporation to act on its behalf in all matters relating to application for Equipment authorization, including the signing of all documents relating to these matters. All acts carried out by Bay Area Compliance Laboratory Corporation on our behalf shall have the same effect as our own action. We, the undersigned, hereby certify that we are not subject to a denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 862. This authorization is valid until further written notice from the applicant. Printed Name: Sam-Leung Title: Merchandising Manager QA-FR-170-B

Circuit Description When the remote control forward ,backward each function by pressing the corresponding key. And transfer signal to encode chip IC .IC internal to encode their corresponding instructions. And with carrier frequency 27.145 MHz to modulation and amplify. Finally output to antenna. The working frequency is 27.145MHz.