FCC ID: 2APU5-WMP500 Wireless Mouse Pad

. This charger works with all Qi-compatible devices (please make sure your device is Qi-compatible)

. For normal operation, no weaker than DC 5V, 2A adapter is required. For fast wireless charging mode, use the QC 2.0/QC 3.0 or PD adapter and compatible smartphones. This wireless charger can charge smartphones with non-metal protective case or silicone covers that are no thicker than 6mm. Instructions Connect the USB cable(included) to a power outlet rated at DC 5V/2A or 9V/2A, the Type-C plug to the Type-C input of the wireless charger. Place your Qi compatible phone with inductive (wireless) charge feature onto the charger (back of phone to charger), then wireless charging of the phone will start immediately. Note- only devices which support Qi wireless charge technology can be wirelessly charged from this charger, please check your device specications. some phone cases do not support Wireless Charging due to the thickness and design. If your phone is compatible with Wireless Charging and you are unable to charge it wirelessly, please remove your phone case and retry. Caution: Do not drop, disassemble or modify this product. Do not expose this product to re or excessive heat. Do not expose this product to water or excessive humidity. Do not put any bare metal on the surface area of wireless charger when it is operating. Increase the separation between the equipment and receiver . Connect the equipment into an outlet on a circuit dierent from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. FCC Radiation Exposure Statement:

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. Wireless Mouse Pad Instruction Manual Please read the following carefully before using the device to ensure safe and proper use. Package Content

. Wireless Mouse Pad

. USB -C to USB-C charging cable

. User Manual Specications i

. Input: DC 5V,2A/ DC 9V,2A

. Output: 15W Max

. Charging Distance6mm General information FCC STATEMENT :

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and

(2) This device must accept any interference received, including interference that may cause undesired operation. Warning:Changes or modications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. NOTE:This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.If this equipment does cause harmful interference to radio or television reception,which can be determined by turning the equipment o and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna. 160*90mm 70g WMP500-SMS-JMT001 WMP500 15W 230111 Steven

Wireless Mouse Pad Model No.: WMP500 Input: 5V 2A 9V 2A Wireless Output: 15W Max FCC ID: 2APU5-WMP500 This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1)This device may not cause harmful interference, and

(2)This device must accept any interference received, including interference that may cause undesired operation. WMP500-TZ-JMT001 WMP500 15W 1 230111 Steven Label location

JMTek Industries( Shenzhen) Co.,Ltd Declaration concerning Antenna Specification It is hereby declared that the product Model No.: WMP500 FCC ID : 2APU5-WMP500 fulfills the requirement in FCC test relating to the antenna type. The device specified above confirms to the FCC recommendations for internal antenna type(s) described below:

Model No. of antenna: N/A Type of antenna:

Gain of the antenna:

Frequency range:

Inductive loop coil Antenna 0 dBi 110.1-205KHz The mounting of the antenna is fixed to the radio module and no other antenna should be used. JMTek Industries( Shenzhen) Co.,Ltd 14G, Innovation Tech Building, Quanzhi Science and Technology innovation Park, ShaJing Street, Bao'an District, ShenZhen, China Shenzhen

China Date: 3/8/2023 Company name:

Address:

City:

ZIP / Postal code:

Country:

Place:

Signature:

version01

1.MECHANICAL DIMENSION (UNIT:mm) 2.SCHEMATICS:

A B C D1 D2 E F G H I 500.5 20.50.5 300.2 220.5 200.5 3-4MM 500.2 2.30.5 50.5 3.WINDING STE P START-FINISH WIRE TYPE TURNS TAPE REMAR K N1 S-F 0.08*105mm 2UEW 10TS (Ref) 4.ELECTRICAL SPECIFICATION:

ITEM TES T CON SPEC L S-F 100KHz,0.25V 6.5uH10%

5.BILF OF MATERIAL DCR S-F AT 25 60m Max IDC Q HI-POT NO. ITEM MATERIAL SPECIFICATION MANUFACTURER SGS NO. 1 2 3 4 5 CORE CORE WIRE TUBE EPOXY G45L NANJINGJINNINGCO,LTD L33H PRQ3/2.5/0.9 NANJINGJINNINGCO,LTD 0.08mm*105 2UEW TAIYI CO.,LTD 10mm 9999 LIANCHENG CO.,LTD CUDAK CO.,LTD HRSW ELECTRONICS CO.,LTD PART NO TITLE G50

- JMTek Industries( Shenzhen) Co.,Ltd -

Federal Communications Commission Authorization and Evaluation Division Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MD 21046 U.S. Agent Designation 3/8/23

[JMTek Industries( Shenzhen) Co.,Ltd] acknowledges their consent for the following contact located in the United States to act as their agent for which authorization is sought (FCC ID: [2APU5-WMP500]):

for service of process for the equipment Name and company of U.S. agent: Tacwa LLC Physical U.S. address of agent: 4109 S 220th Pl Kent WA 98032 USA FRN of U.S. agent: 0033491978 Email address of U.S. agent: Tai@jmtek.com

[Tacwa LLC] acknowledges their obligation to accept service of process on behalf of [JMTek Industries( Shenzhen) Co.,Ltd].

[JMTek Industries( Shenzhen) Co.,Ltd] accepts its obligation to maintain an agent for service of process in the United States for no less than one year after either the grantee has permanently terminated all marketing and importation of the applicable equipment within the U.S., or the conclusion of any Commission-related administrative or judicial proceeding involving the equipment, whichever is later. By signing this form, we confirm the above and that we are aware of the application requirements listed under 2.911(d)(7). Sincerely, Signature

[Cici Jiang]

[GM]

JMTek Industries( Shenzhen) Co.,Ltd 3 0 V

, U

) 7

) d

1 1 9 2 _ t n e g A _ S U Signature

[Tai Y Ly]

[Manager]

[Tacwa LLC]

l e d o m

_ 8 4 The information provided in this letter is based on the referenced rule parts of Title 47 of the CFR as well as KDB 986446 D01. An expiration date for this letter does not exist. In case the U.S. agent changes, the grantee is obligated to notify the FCC.

- JMTek Industries( Shenzhen) Co.,Ltd -

Federal Communications Commission Authorization and Evaluation Division Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MD 21046 3/8/23 To whom it may concern:

We, [JMTek Industries( Shenzhen) Co.,Ltd], hereby certify that the equipment for which authorization is sought (FCC ID: [2APU5-WMP500]) is not covered equipment prohibited from receiving an equipment authorization pursuant to 2.903 of the FCC rules. We also certify that, as of the date of the filing of the application, we are not identified on the Covered List (https://www.fcc.gov/supplychain/coveredlist) as an entity producing covered equipment. By signing this form, we confirm the above and that we are aware of the application requirements listed under 2.911(b) and (d)(5) and (6). Sincerely, 2 0 V

, U

) i i

d n a

) i

) 5

) d

1 1 9 2 _ u q E d e r e v o C

l e d o m

_ 2 6 Signature

[Cici Jiang]

[GM]

[JMTek Industries( Shenzhen) Co.,Ltd]

The information provided in this letter is based on the referenced rule parts of Title 47 of the CFR as well as KDB 986446 D01.