FCC ID: T62-IPREM Handheld Remote Control for Trolling Motor

Owners Manual TABLE OF CONTENTS Introduction ......................................................................................3 Two-Year Warranty ........................................................................ 4-5 Installation.................................................................................... 6-25 Parts List............................................................................................6-9 Preparing for Installation ....................................................................10 Installation of i-Pilot Controller......................................................11-27 Verifying Installation ..................................................................... 28-29 Getting Started........................................................................... 30-37 Knowing Your Remote ................................................................. 30-32 Knowing Your i-Pilot Controller ................................................... 33-36 System Startup ...................................................................................37 Manual Control........................................................................... 38-41 GPS Motor Control......................................................................42-61 Spot Lock ..................................................................................... 44-47 Cruise Control.............................................................................. 48-49 AutoPilot /Advanced AutoPilot .................................................... 50-55 Track Recording/Playback.............................................................56-61 Frequently Asked Questions........................................................ 62-63 Troubleshooting.......................................................................... 64-67 Glossary ..................................................................................... 68-69 Compliance Statements .............................................................. 70-71 Warranty Card ................................................................................ 72 Accessories...................................................................................... 73 Notes ..........................................................................................74-75 2 minnkotamotors.com 2377150 Revision A INTRODUCTION Overview Thank you for purchasing the Minn Kota i-Pilot. This revolutionary control system uses GPS technology to record and store tracks and locations which are then used to deliver unprecedented levels of boat control. Intuitive features and wireless control help to accurately position your boat and improve your bait presentation. i-Pilot navigates and positions your boat for you, so you can focus on shing. This i-Pilot User Guide is divided into four main sections: Installation, Getting Started, Manual Control, and GPS Motor Control. A waterproof and easy-to-read Quick Reference Guide is also included as a supplement to the User Guide, both of which can be stored in the boat for easy access. A French version of the manual is available on line at minnkotamotors.com Une version franais du manuel est disponible en ligne minnkotamotors.com Safety and Cautions You are responsible for the safe and prudent operation of your vessel. We have designed i-Pilot to be an accurate and reliable tool that will enhance boat operation and improve your ability to catch sh. This product does not relieve you from the responsibility for safe operation of your boat. You must avoid hazards to navigation and always maintain a permanent watch so you can respond to situations as they develop. You must always be prepared to regain manual control of your boat. Learn to operate your i-Pilot in an area free from hazards and obstacles. Warranty and Registration To receive all the benets of your product warranty please ll out and mail the warranty registration card. You may also register your product online at minnkotamotors.com. Correctly installing i-Pilot on a Minn Kota trolling motor will not void the original motor warranty or the warranty of any previously installed accessories. Installing i-Pilot will not extend the warranty of any Minn Kota product it is being installed into or in conjunction with. minnkotamotors.com 3 LIMITED T WO-YEAR WARRANT Y ON ENTIRE PRODUCT:

Johnson Outdoors Inc. warrants to the original purchaser that the purchasers entire i-Pilot System accessory is free from defects in materials and workmanship appearing within two (2) years after the date of purchase. Johnson Outdoors Inc. will, at its option, either repair or replace, free of charge, any parts found to be defective during the term of this warranty. Such repair or replacement shall be the sole and exclusive liability of Johnson Outdoors Inc. and the sole and exclusive remedy of the purchaser for breach of this warranty. These limited warranties do not apply to i-Pilot Systems used commercially, nor do they cover normal wear and tear, blemishes that do not affect the operation, or damage caused by accidents, abuse, alteration, modication, misuse or improper care or maintenance. DAMAGE CAUSED BY THE USE OF OTHER REPLACEMENT PARTS NOT MEETING THE DESIGN SPECIFICATIONS OF THE ORIGINAL PARTS WILL NOT BE COVERED BY THIS LIMITED WARRANTY. The cost of normal maintenance or replacement parts that are not defective are the responsibility of the purchaser. To obtain warranty service in the U.S., the part believed to be defective and proof of original purchase (including the date of purchase) must be presented to a Minn Kota Authorized Service Center or to Minn Kotas factory service center in Mankato, MN. Any charges incurred for service calls, transportation or shipping/freight to/from the Minn Kota Authorized Service Center or factory, labor to haul out, remove, re-install or re-rig products removed for warranty service, or any other similar items are the sole and exclusive responsibility of the purchaser. i-Pilot systems purchased outside of the U.S. (or parts of such systems) must be returned prepaid with proof of purchase (including the date of purchase and serial number) to any Authorized Minn Kota Service Center in the country of purchase. Warranty service can be arranged by contacting a Minn Kota Authorized Service Center listed on the enclosed sheet or by contacting the factory at 4 minnkotamotors.com 1-800-227-6433, 1-507-345-4623 or fax 1-800-527-4464. Note: Do not return your i-Pilot or parts to your retailer. Your retailer is not authorized to repair or replace them. THERE ARE NO EXPRESS WARRANTIES OTHER THAN THESE LIMITED WARRANTIES. IN NO EVENT SHALL ANY IMPLIED WARRANTIES, INCLUDING ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR PARTICULAR PURPOSE, EXTEND BEYOND TWO YEARS FROM THE DATE OF PURCHASE. IN NO EVENT SHALL JOHNSON OUTDOORS MARINE ELECTRONICS L.L.C. BE LIABLE FOR INCIDENTAL, CONSEQUENTIAL OR SPECIAL DAMAGES. Some states do not allow limitations on how long an implied warranty lasts or the exclusion or limitation of incidental or consequential damages, so the above limitations and/or exclusions may not apply to you. This warranty gives you specic legal rights, and you may also have other legal rights which vary from state to state. WARNING: This product contains chemical(s) known to the state of California to cause cancer and/or reproductive toxicity. minnkotamotors.com 5 PARTS LIST VIEW TERROVA 1 2 3 4 ITEM

#

1 2 3 4 5*

6*

PART NUMBER DESCRIPTION 2990255 2994085 2372100 2370817 2377150 MANUAL, I-PILOT 2377151 MANUAL, I-PILOT QUICK REFERENCE GUIDE I-PILOT CONTROLLER, TERROVA REMOTE, ASSEMBLY I-PILOT SCREW, #8-18 X 5/8" SS LANYARD, REMOTE WITH CARABINEER QTY 1 1 4 1 1 1

* Not Shown In Exploded View 6 minnkotamotors.com INSTALLATION PARTS LIST VIEW RIPTIDE ST 1 2 3 ITEM

#

1 2 3 4 5*

6*

PART NUMBER DESCRIPTION 2990256 2994085 2372100 2370817 2377150 MANUAL, I-PILOT 2377151 MANUAL, I-PILOT QUICK REFERENCE GUIDE I-PILOT CONTROLLER, RIPTIDE ST REMOTE, ASSEMBLY I-PILOT SCREW, #8-18 X 5/8" SS LANYARD, REMOTE WITH CARABINEER 4 QTY 1 1 4 1 1 1

* Not Shown In Exploded View minnkotamotors.com 7 PARTS LIST VIEW POWERDRIVE V2 1 2 6 7 5 4 3 ITEM

#

1 2 3 4 5 6 7 8*

9*

PART NUMBER DESCRIPTION 2990265 2994085 2372100 2370817 2224704 2376312 2303430 2377150 MANUAL, I-PILOT 2377151 MANUAL, I-PILOT QUICK REFERENCE GUIDE I-PILOT CONTROLLER, POWERDRIVE V2 REMOTE, ASSEMBLY I-PILOT SCREW, #8-18 X 5/8" SS LANYARD, REMOTE WITH CARABINEER INSERT PLUG, BLACK SLOTTED TIE, NYLON SCREW - 1/4 - 20 X 5/8 - SELFTAP ZP QTY 1 1 4 1 1 5 2 1 1

* Not Shown In Exploded View 8 minnkotamotors.com minnkotamotors.com INSTALLATION PARTS LIST VIEW RIPTIDE SP 1 2 3 8 5 7 6 4 ITEM

#

1 2 3 4 5 6 7 8 9*

10*

PART I-PILOT CONTROLLER, RIPTIDE SP REMOTE, ASSEMBLY I-PILOT SCREW, #8-18 X 5/8" SS LANYARD, REMOTE WITH CARABINEER INSERT PLUG, WHITE SLOTTED TIE, NYLON NUMBER DESCRIPTION 2990266 2994085 2372100 2370817 2224705 2376312 2375403 HEAT SHRINK, .375 X 2 ADHESIVE LINED 3:1 2332104 2377150 MANUAL, I-PILOT 2377151 MANUAL, I-PILOT QUICK REFERENCE GUIDE SCREW - 1/4 - 20 X 5/8 SS QTY 1 1 4 1 1 5 10 2 1 1

* Not Shown In Exploded View minnkotamotors.com minnkotamotors.com 9 PREPARING FOR INSTALL ATION Preparing for Installation Tools you will need during installation Terrova and Riptide ST

-Phillips screwdriver PowerDrive V2

-Phillips screwdriver

-Needle-nose pliers

-Utility knife Riptide SP

-Phillips screwdriver

-Needle-nose pliers

-Utility knife

-Heat gun or other heat source for installing heat shrink Before installing i-Pilot on your motor, make sure the trolling motor is properly installed on your boat. Find a clean and dry location for performing the installation. Most importantly, disconnect all power to the trolling motor before installation. Not only will this protect you but also the sensitive electronics you are about to install. Read through the entire installation process before performing the installation. If you need help or need further instruction on installing i-Pilot, please go online at minnkotamotors.com for a full step-by-step, guided installation video. You may also call Minn Kota technical service at 1-800-227-6433 to talk to a customer service representative. 10 minnkotamotors.com minnkotamotors.com INSTALLATION INSTALL ATION OF I-PILOT CONTROLLER For PowerDrive V2 and Riptide SP trolling motors go to page 13. i-Pilot Installation on Terrova and Riptide ST Trolling Motors

*i-Pilot will override all CoPilot functionality. CoPilot remotes will not function with i-Pilot.

*The Terrova foot pedal is fully functional and supported when i-Pilot is installed correctly. 1. Remove all power to the trolling motor. FIGURE 1 2. Remove control box cover screws and cover using Phillips screwdriver. (Figure 1) FIGURE 2 3. If the trolling motor has the AutoPilot feature, unplug the AutoPilot control board and remove it from the control box. (Figures 2 and 3) FIGURE 3 minnkotamotors.com minnkotamotors.com 11 4. Plug the i-Pilot controller connector into the accessory connector as shown.

(Figure 4) Be careful to orient connector properly prior to pushing together. The plug will click twice when pushing it together and the yellow end will be fully covered when installed properly. Make sure connector is aligned properly. (Figure 5) Make sure connector is fully seated as shown. (Figure 5) 5. Place the i-Pilot controller where the control box cover was installed and secure with supplied #8 screws. Do not over tighten screws.

(Figure 6) 6. i-Pilot is now installed. Proceed to page 28 to verify your installation. FIGURE 4 FIGURE 5 12 minnkotamotors.com minnkotamotors.com INSTALLATION i-Pilot Installation on PowerDrive V2 and Riptide SP

*Note: Once i-Pilot is installed the PowerDrive V2 foot pedal cannot be used again unless i-Pilot is fully uninstalled. 1. Remove all power to the trolling motor. 2. If a CoPilot is installed, it must be removed as follows:

a. Disconnect motor connector and foot pedal connector from CoPilot.

(Figure 7) b. Remove the CoPilot receiver from the motor by removing both mounting screws. Do not replace these screws as the side plates will be removed in step 13 of this installation. (Figure 8) FIGURE 6 FIGURE 7 FIGURE 8 minnkotamotors.com minnkotamotors.com 13 3. Remove control box cover screws and cover using Phillips screwdriver. (Figure 9) 4. If the trolling motor has AutoPilot it must be removed as follows:

a. Disconnect all six AutoPilot connectors from AutoPilot controller, using a needle-nose pliers and a utility knife to remove any heat shrink insulation that may exist. (Figure 10) b. Remove the AutoPilot controller from the head of the trolling motor.

(Figure 11) FIGURE 9 FIGURE 10 FIGURE 11 14 minnkotamotors.com minnkotamotors.com INSTALLATION 5. Remove grommet by pulling back on coil cord strain relief and pushing down on grommet until it pops out.

(Figure 12) 6. Review the cables in the head of the trolling motor. a. If a sonar cable is present, it must be routed around the outer perimeter of the control box as shown. The sonar ground wire should also be routed as shown. (Figure 13) b. The motor power wires Grommet FIGURE 12 Sonar Cable (Universal Sonar Motors Only) must be routed as shown.

(Figure 13) Sonar Ground Wire Power Wires AutoPilot Wires

(AutoPilot Motors Only) Sonar Cable FIGURE 13 minnkotamotors.com minnkotamotors.com 15 7. If AutoPilot was removed, insulate the loose AutoPilot connectors as follows:

a. For PowerDrive V2 Motors: Using a needle-nose pliers push all six AutoPilot connectors that were disconnected in step 4 onto terminal holders located on the underside of the i-Pilot Controller. (Figure 14) IMPORTANT: Pull on each wire to make sure it is secured properly. Loose wires can cause damage to i-Pilot Controller and the entire motor. AutoPilot connectors must be placed onto holders exactly as shown.

(Figure 15) FIGURE 14 Insert AutoPilot wires into terminal holders. FIGURE 15 Pinch ends of heat shrink shut using needle-

nose pliers. FIGURE 16 Insulate and seal six AutoPilot wires on Riptide SP motors with supplied heat shrink. 16 minnkotamotors.com minnkotamotors.com INSTALLATION b. For Riptide SP Motors:

Apply heat shrink insulation supplied in bag assembly to the ends of all six loose AutoPilot connectors as shown. (Figure 16) Use a zip tie to bundle connectors together. Trim the zip tie and place connector bundle in the middle of the control box as shown. (Figure 17) 8. Route i-Pilot controller cable through grommet hole and through center of coil cord.

(Figure 18) FIGURE 17 Place insulated AutoPilot wires in the bottom center of the control box as shown. FIGURE 18 minnkotamotors.com minnkotamotors.com 17 9. Install new grommet supplied with i-Pilot by snapping it into the hole located in front of the coil cord strain relief. The i-Pilot controller cable must be placed in the pass-through slot of the grommet. (Figure 19) 10. Place the i-Pilot controller where the control box cover was installed. Pull any extra controller cable out of the control box by gently pulling on the cable. (Figure 20) 11. Secure cover with supplied

#8 screws. Do not over tighten screws. (Figure 21) FIGURE 19 FIGURE 20 FIGURE 21 18 minnkotamotors.com minnkotamotors.com INSTALLATION 12. Secure the i-Pilot controller cable to the motor coil cord in all three locations shown using zip ties provided. (Figure 22) Trim zip ties using utility knife. Failure to secure cable will result in possible damage to the cabling during operation. 13. Remove the left and right side plates of trolling motor by loosening all four side plate screws using a Phillips screwdriver. (Figure 23) Zip Tie Location 1 Zip Tie Location 2 Zip Tie Location 3 FIGURE 22 FIGURE 23 minnkotamotors.com minnkotamotors.com 19 14. Remove center housing by pushing in on both sides and lifting up at the same time. This will expose the main control board and wiring. (Figure 24) FIGURE 24 Entrance of steering cable through center housing FIGURE 25 Disconnect both wires by removing heat shrink and pulling them apart. 20 minnkotamotors.com minnkotamotors.com INSTALLATION 15. The steering motor cable passes through the top of the center housing removed in step 14. This cable contains a black and white wire. Disconnect these two wires by pulling each connector apart. (Figure 25) Riptide SP motors will have this connections covered with heat shrink which must be removed with a utility knife. 16. Remove the cable strain relief that is secured to the base of the motor and install the i-Pilot controller steering cable into the open strain relief slot. (Figure 26) FIGURE 26 minnkotamotors.com 21 17. Reinstall the cable strain relief as shown. The i-Pilot controller steering cable should slide freely through the strain relief when installed properly.

(Figures 27 and 28) Foot Pedal Cable Motor Power Cable i-Pilot Controller Steering Cable Reinstall strain relief screw. FIGURE 27 and 28 22 minnkotamotors.com minnkotamotors.com INSTALLATION 18. If the motor is a Riptide SP, slide four pieces of heat shrink insulation over each side of the wires that were disconnected in step 15.

(Figure 29) Riptide SP Motors Only:

Slide heat shrink over steering motor wires. FIGURE 29 minnkotamotors.com minnkotamotors.com 23 19. Connect the black and white wires from the i-Pilot controller cable to the back and white steering motor wires, making sure black is connected to black and white is connected to white. (Figure 30) Connect steering wires:

white to white black to black FIGURE 30 24 minnkotamotors.com minnkotamotors.com INSTALLATION 20. If heat shrink insulation was installed at step 18, complete the installation by positioning the heat shrink over the connections and shrink down, using a heat gun or other heat source, being careful not to overheat any wire or parts. Riptide SP Motors Only:

Seal connections with heat shrink. IMPORTANT: DO NOT OVERHEAT WIRES OR SURROUNDING PARTS WHEN INSTALLING HEAT SHRINK!

21. Reinstall center housing over control board by pushing it down until the side ngers lock into place. The new i-Pilot Controller steering cable should be exiting the cable exit hole at the center and bottom of the center housing.

(Figure 31) FIGURE 31 minnkotamotors.com minnkotamotors.com 25 FIGURE 32 FIGURE 33 26 minnkotamotors.com minnkotamotors.com INSTALLATION 22. Reinstall both side plates using Phillips screwdriver. If a Co-Pilot was uninstalled, use new -20 X 5/8" Phillips screws provided. (Figure 32) 23. If a foot pedal is connected to the trolling motor, it must be disconnected. Once i-Pilot has been installed the foot pedal cannot be used unless i-Pilot is completely uninstalled. 24. Connect i-Pilot controller cable to the foot pedal connector, making sure the connector nut is tight. (Figure 33) IMPORTANT: DO NOT place dielectric grease or any type of lubricant in the connector. 25. i-Pilot is now installed. minnkotamotors.com minnkotamotors.com 27 VERIFYING INSTALL ATION It is important to verify your i-Pilot installation prior to going on the water. If this cannot be done, it is highly recommended that system verication be done in an open area on a calm day with a fully operational outboard motor for a backup means of powering your boat. To verify that i-Pilot is working properly before going on the water, follow the steps below. 1. Trolling motor should be correctly installed and mounted to the bow of a boat. 2. The boat and trolling motor must be located outside and have a direct view of the sky to obtain GPS satellite signals. 3. Verify that all obstructions are away from the prop in all directions in both the stowed and deployed positions. 4. Connect power to the trolling motor. 5. Deploy the motor so the motor shaft is completely vertical. 6. i-Pilot will emit three long audio tones on startup. 7. Press any button on the i-Pilot remote. 8. The i-Pilot remote LCD will come on; prop speed and the GPS antenna icon will be displayed. It should take no longer than two minutes to obtain a GPS signal strength of at least one bar. 28 minnkotamotors.com minnkotamotors.com INSTALLATION 9. When i-Pilot is powered up, it starts to gather satellite information about its location. A minimum satellite signal level must be achieved before all i-Pilot functionality is available. This minimum level is one bar on the GPS signal icon. At initial startup only manual functions will be available. 10. Verify all manual functions by pressing and

. 11. If you experience any problems with any of the steps above, or cannot obtain a GPS satellite signal, refer to the troubleshooting section beginning on page 64. minnkotamotors.com minnkotamotors.com 29 KNOWING YOUR REMOTE Layout The i-Pilot remote is divided into four sections: Manual Control, Tracks, Spot Lock, and Cruise Control/AutoPilot. Buttons in the Manual Control section of the remote do not require a GPS signal to operate and give you full, immediate control over steering, speed and prop functions similar to a CoPilot. All other buttons require a minimum GPS signal strength of one bar in order to operate. Buttons located in the Tracks section are used for track recording and playback. Spot Lock buttons are located in the Spot Lock section. Cruise Control/AutoPilot are located in the Cruise Control/AutoPilot section. Construction The remote is waterproof and oats in water. Range The range of the remote will be greatly reduced if it is used near or mounted to any metal object including aluminum or steel. It is also recommended that the front end of the remote not be obstructed during use. Battery Life Remote battery life is subject to frequency of use and is especially impacted by how often the LCD backlight is used. When the remote battery is low, Backlight button will be disabled when Power When a button is pressed on the remote it will automatically turn on. To turn the remote off press and hold turn itself off thirty minutes after the last button press if a learned i-Pilot controller is powered up and within transmitting range. The remote will turn off after three seconds if the i-Pilot controller is powered down or out of transmitting range. for three seconds. The remote will automatically will appear on the remote LCD. The is displayed to conserve battery power. 30 GETTING STARTED MANUAL CONTROL Steer Left Steer Right Prop On/Off Speed Down Speed Up START END High Speed Bypass Toggles the motor speed between its current setting and speed 10. Backlight Turns the remote LCD backlighting on for six seconds. CRUISE CONTROL/

AUTOPILOT Advanced AutoPilot and AutoPilot Turns Advanced AutoPilot on and off when pressed once. Turns AutoPilot on when held for two seconds. END START TRACKS Track to End Navigates to the nearest location on a previously recorded track and follows it to its end. Track to Start Navigates to the nearest location on a previously recorded track and follows it to its start. Track Record Starts and ends the recording of a track to a selected memory location. Record Pause/Escape Pauses the recording of a track and then resumes the recording when pressed again. SPOT LOCK Spot Lock Turns spot lock on and records it to a memory location. Spot Lock Recall Recalls a spot lock location from memory and turns spot lock on. Cruise Control Turns cruise control on and off using the current GPS speed as the target speed. Motor Speed Track Record On Track to Start On Spot Lock On Track to End On Memory Location GPS Signal Strength Remote Battery Low Cruise Control On Prop On/Off GPS Speed Advanced AutoPilot On AutoPilot On minnkotamotors.com 31 Remote Battery Replacement

*NOTE: Panasonic brand batteries will not work with the i-Pilot remote. 1. Make sure hands are clean, dry and static free. Discharge any static electricity by touching a metal object that is grounded. *Static electricity can damage the circuit board. 2. With the remote upside down remove the six case screws. 3. Remove the bottom cover. 4. While pushing down in the middle of the circuit board lift the old battery out and replace with a new CR2450 coin cell battery. 5. Replace back cover and reinstall case screws. Do not over tighten case screws as it will damage the remote enclosure. Factory torque setting is seven inch pounds. Remove battery and replace. 32 minnkotamotors.com minnkotamotors.com GETTING STARTED KNOWING YOUR I-PILOT CONTROLLER Construction The i-Pilot controller contains a very sensitive digital compass and is where all GPS satellite and i-Pilot remote signals are received. It is very important that the controller have a clear view of the sky in all directions and has a clear line of sight to the remote for optimum performance. All electronics within the controller enclosure are completely sealed. i-Pilot Speaker Remote Learn Button Remote Learning The i-Pilot remote is prelearned to the controller from the factory. The top of the controller has a single learn button to allow additional remotes to be added to the system. To learn additional remotes:

1. Power up the trolling motor. 2. Push and hold the learn button down. A steady audio tone will be heard while holding this button. 3. While holding the learn button down push any button on the remote being programmed. Three short chirps will be heard when the remote is successfully learned. A remote can only be learned to one controller at a time. A controller can have an unlimited number of remotes learned to it. minnkotamotors.com minnkotamotors.com 33 Audio Modes The i-Pilot Controller also contains an internal speaker which can be programmed to work in two different audio modes. The speaker is programmed to operate in audio mode one from the factory. To enable down at the same time for three different audio modes hold seconds. For an explanation of each audio mode and their sounds see the table below. and WHAT CONDITION CAUSES IT Startup Manual prop on Manual prop off Speed + (when less than max speed) Speed - (when greater than speed 0) High Speed Bypass enable High Speed Bypass disable Button press for any of these (enable or disable): REC, Pause, Track to Start, Track to End, AutoPilot, Cruise Control, Spot Lock, Spot Lock Recall Moving more than a quarter mile from the last track point while in Record Pause mode When GPS Signal Strength goes to no bars while in a GPS-based mode AUDIO MODE Modes 1 and 2 Mode 2 Mode 2 Mode 2 Mode 2 Mode 2 Mode 2 Mode 2 Mode 2 Mode 2 AUDIO PATTERN 4 Short beeps Single beep Double beep Single beep Single beep Single beep Double beep Single beep Error Error 34 minnkotamotors.com GETTING STARTED WHAT CONDITION CAUSES IT Attempting to enable a GPS feature when no signal strength bars are shown Attempting to replay a Track or recall a Spot Lock location when the boat is beyond the minimum distance MOM button on the footpedal is pressed and a remote button press attempts to override it End of track attained during track playback (in conjunction with cancelling mode and turning the prop off) Switch to Audio Mode 1 Switch to Audio Mode 2 Learn button is pressed Learn successfully completed AUDIO MODE Mode 2 Mode 2 Mode 2 Mode 2 AUDIO PATTERN Error Error Error High-Low, High-Low, High-Low Modes 1 and 2 Modes 1 and 2 Modes 1 and 2 Modes 1 and 2 Single beep Double beep Steady tone 4 Longer beeps minnkotamotors.com minnkotamotors.com 35 Power The i-Pilot controller will turn on whenever the trolling motor has power. For Terrova and Riptide ST motors this is when the green system ready light is on. For PowerDrive V2 and Riptide SP motors this is whenever the motor is connected to power.

* For this reason it is very important to disconnect a PowerDrive V2 or Riptide SP motor from power when not in use or battery drain will occur. Accuracy The accuracy and responsiveness with which i-Pilot controls your boat is highly dependent upon many variables. Just a few of these variables and their general effects on responsiveness and accuracy are given below so that the behavior of the system can be understood. VARIABLE Ratio of motor thrust to boat weight Wind GPS signal strength Trolling motor battery power level EFFECT Excessive thrust on a smaller boat can cause i-Pilot to overcorrect. Not enough thrust on a large boat can cause i-Pilot to respond slowly. Excessive wind and/or current can reduce i-Pilots positioning accuracy. The greater number of GPS signal bars the greater the accuracy. A fully charged battery will give the best performance. 36 minnkotamotors.com minnkotamotors.com GETTING STARTED System Startup Once you have veried i-Pilots installation its time to start using it on the water. Follow these simple steps each time you power up your trolling motor for successful operation:

1. Connect trolling motor to power. 2. Deploy trolling motor into water. 3 Push any button on your remote. The remote LCD will show prop speed and GPS signal strength. 4. You are now able to use all manual functions:

and

. 5. After i-Pilot has obtained a minimum GPS signal strength of one bar, all remaining functions will become available. minnkotamotors.com minnkotamotors.com 37 MANUAL CONTROL FUNCTIONALIT Y START END This section describes all Manual Control functions of i-Pilot. A manual function is one in which the operator takes full control of the function such as manually steering the motor in a desired direction or manually adjusting the prop speed to the desired setting. Any of these functions do not require a GPS signal. How Do I . Turn the Motor On/Off?

Motor On/Off To turn the motor on or off press

. The prop icon on the LCD will be on if the prop is enabled and off if the prop is disabled. With the prop enabled, the icon will be stationary if the motor speed is zero and the icon will rotate if the motor speed is greater than zero. Prop Enabled Motor Speed Greater Than Zero Pressing the MOM or CON button on the foot pedal will adjust the motor speed setting to the foot pedal speed setting. 38 minnkotamotors.com minnkotamotors.com MANUAL CONTROL How Do I . Control Motor Speed?

Motor Speed Control Increase Motor Speed To increase the motor speed push of on the remote. Each push will increment the motor speed by to a maximum of 10. Decrease Motor Speed To decrease the motor speed push of will decrement the motor speed by to a minimum of 0. on the remote. Each push The remote LCD will display the current motor speed setting. This is not to be confused with the GPS speed which is also displayed on the remote LCD. Motor Speed GPS Speed While the MOM button is pressed on the foot pedal, all speed and prop changes from the i-Pilot remote are ignored. minnkotamotors.com minnkotamotors.com 39 How Do I . Steer the Motor?

Motor Steering Control Steer Left To steer the motor to the left press Steer right To steer the motor to the right press

. If a steering button is held down for more than six to eight seconds, the steering will stop to prevent the coil cord from wrapping on the motor. 40 minnkotamotors.com minnkotamotors.com

MANUAL CONTROL How Do I . Engage High Speed Bypass?

High Speed Bypass Operation Engage Pressing maximum immediately. will set the motor speed to Disengage Pressing at previously. again will set the motor speed to the value it was

*Note: High Speed Bypass does not enable or disable the prop. How Do I . Turn LCD Backlighting On?

LCD Backlight Button To turn on LCD backlighting press

. The backlight will turn off eight seconds after the last button press to conserve battery power. minnkotamotors.com 41 UNDERSTANDING HOW THE I-PILOT SYSTEM WORKS Navigation i-Pilot uses GPS satellite signals as well as digital compass data to know where it is, where it is heading and the direction the motor is pointing. Since i-Pilot depends on GPS satellite signals for navigation, a minimum GPS signal level of one bar is required in order for GPS navigation controls to be enabled. Best results are achieved when a GPS signal level of four bars can be obtained. In simple terms, i-Pilot remembers and creates points to navigate your boat automatically. i-Pilot also uses a method of GPS navigation called arrival circles. These imaginary circles allow i-Pilot to understand when it has drifted away from a point and when it has arrived at a point. The size of the arrival circles vary depending on GPS signal strength, thus the greater the signal strength the smaller the arrival circles. Tracks Tracks are made of many points that i-Pilot records when recording a track. The distance between these points varies based on GPS signal strength and the speed at which you record the track. When a track is played back, i-Pilot uses the track points and arrival circles to navigate the track. 42 minnkotamotors.com minnkotamotors.com GPS MOTOR CONTROL Memory i-Pilot has the capability of storing up to three individual tracks (each two miles in length) and three individual Spot Lock locations. These locations are stored in memory even when power is removed from the system. Spot Lock and Track memory locations are separate from each other and they cannot over write each other. Memory locations are identied on the remote LCD with an icon shown as A, B or C. When the memory icon is ashing, a different location can be selected by pressing or

. minnkotamotors.com minnkotamotors.com 43 HOW SPOT LOCK WORKS Spot Lock Spot Lock uses a single point as a reference for the spot you want to stay on. This point is recorded and stored into one of the three memory locations when the Spot Lock button is pushed. Around the Spot Lock location i-Pilot uses an arrival circle to determine prop speed and direction. If i-Pilot sees it is within the circle, it will adjust the motor speed to zero. If i-Pilot sees it is outside of the circle, it will control motor speed in an attempt to get the boat back into the circle. START END 44 minnkotamotors.com minnkotamotors.com SPOT LOCK E N T R R U C W I N D /

minnkotamotors.com minnkotamotors.com 45 ENGAGING SPOT LOCK on the remote. 1. Press 2. The Memory Location icon will ash on the remote LCD for three seconds, allowing you to choose a memory location by pressing again or waiting for or three seconds accepts the memory location. Pressing DISENGAGING SPOT LOCK 1. To disengage Spot Lock press any of these buttons:

or

. Pressing any foot pedal button will disengage Spot Lock. 46 minnkotamotors.com minnkotamotors.com SPOT LOCK RE-ENGAGE A SAVED SPOT LOCK LOCATION 1. Manually navigate the boat to within a quarter mile of the saved Spot Lock location. Due to safety reasons, i-Pilot will not re-engage a saved Spot Lock location greater than a quarter mile away. 2 Press 3. The Memory Location icon will ash on on the remote. the remote LCD for three seconds allowing you to choose a memory location by pressing again or waiting for three seconds accepts the memory location. Pressing or SPOT LOCK ESCAPE 1. If the Spot Lock button is accidentally hit, press or any manual navigation button within three seconds to cancel the command. Using Spot Lock with Other i-Pilot Functions Since Spot Lock takes over full control of the motor, it cannot be used in combination with other i-Pilot functions. The momentary button on the foot pedal will not function when Spot Lock or Spot Lock Recall is engaged. minnkotamotors.com minnkotamotors.com 47 HOW CRUISE CONTROL WORKS Cruise Control

(Advanced Functionality) i-Pilot automatically controls the motor speed to maintain a constant GPS speed. START END Adjusting the motor speed or pressing the CON button from the foot pedal will disengage Cruise Control. 48 minnkotamotors.com minnkotamotors.com CRUISE CONTROL ENGAGING CRUISE CONTROL on the remote. 1. Press 2. The current GPS speed will ash, displaying your current speed as the target GPS speed on the remote LCD for three seconds. 3. Press or to increase or decrease the target speed or press Control immediately. again to engage Cruise DISENGAGE CRUISE CONTROL 1. Pressing will disengage Cruise Control. ADJUSTING TARGET SPEED WITH CRUISE CONTROL ENGAGED 1. With Cruise Control engaged press target speed by 0.1 MPH increments. or to adjust the Using Cruise Control with Other i-Pilot Functions Cruise Control can be used in combination with Advanced AutoPilot, AutoPilot, Track Recording, and Track Playback. minnkotamotors.com minnkotamotors.com 49 HOW AUTOPILOT WORKS Two different versions of AutoPilot are available Advanced AutoPilot and AutoPilot. There are distinct differences between the two AutoPilots and how they control your boat. AutoPilot AutoPilot uses an internal compass to provide heading lock. When AutoPilot is on, it keeps the motor pointed in the same compass direction. If a manual steering correction is made, AutoPilot locks onto the new compass heading to which the boat was steered. This method of heading tracking does not take into account external forces such as a side wind or currents, which can allow side drift. START END 50 minnkotamotors.com minnkotamotors.com AUTOPILOT AUTOPILOT HEADING POSSIBLE DEVIATION DUE TO WIND/CURRENT minnkotamotors.com minnkotamotors.com 51 HOW ADVANCED AUTOPILOT WORKS Advanced AutoPilot Advanced AutoPilot not only uses compass heading but also GPS signal data to correct for cross winds, current and other external forces to keep the boat on a straight line. When Advanced AutoPilot is turned on, it generates a set of GPS points in a straight track line in the heading direction. i-Pilot now navigates to each individual point on this track line. When the user steers to a new heading, a new track line of GPS points are laid down in the new heading direction. START END 52 minnkotamotors.com minnkotamotors.com ADVANCED AUTOPILOT ADVANCED AUTOPILOT HEADING POSSIBLE DEVIATION DUE TO WIND/CURRENT GPS POINT GPS POINT GPS POINT minnkotamotors.com minnkotamotors.com 53 ENGAGING ADVANCED AUTOPILOT AND AUTOPILOT 1. To engage Advanced AutoPilot, press once. To engage AutoPilot, press and hold for two seconds. 2. The Advanced AutoPilot or AutoPilot icon will be displayed on the remote LCD. 3. To adjust desired heading, manually steer motor to new heading. i-Pilot will lock onto new heading. Advanced AutoPilot Using Advanced AutoPilot and AutoPilot with Other i-Pilot Functions Advanced AutoPilot and AutoPilot can be used in combination with Cruise Control and while recording a track. AutoPilot Advanced AutoPilot can be turned on by pressing the AP button on the foot pedal. 54 minnkotamotors.com minnkotamotors.com ADVANCED AUTOPILOT/AUTOPILOT Which AutoPilot Do I Use and When?

With all the external variables, this question can be difcult to answer. Both AutoPilots have their benets based on the type of shing and bait presentation desired. Advanced AutoPilot will keep the boat on a true straight path in most conditions. When very extreme conditions exists such as very strong winds or current, the trolling motor may not have enough power to control the boat smoothly. In these extreme cases it may be best to use AutoPilot and let the boat move with the wind or current if the motor is not powerful enough to overcome it. AutoPilot helps you maintain a constant heading but does not compensate for wind or currents. Both Advanced AutoPilot and AutoPilot are valuable tools the sherman can use for accurate and precise bait presentation. We highly recommend getting on the water and trying both Advanced AutoPilot and AutoPilot in various shing situations and applications. With experimentation and time you will nd which AutoPilot works best for you in a given situation. AutoPilot cannot be turned on by using the AP button on the foot pedal. minnkotamotors.com minnkotamotors.com 55 HOW TRACK RECORDING AND PL AYBACK WORK Track Recording and Playback When the Track Record button is pressed, i-Pilot starts to record GPS position data in the form of track points. The distance between these points varies based on the speed of the boat and the GPS signal strength. The very rst track point recorded is called the start. The last point recorded is called the end. i-Pilot sees a recorded track as a series of these track points. When a Track to Start or Track to End button is pushed, i-Pilot will navigate to the nearest track point. Once this nearest track point is reached, it will then follow the track points in sequence back to either the start or end based on which button was pressed. Once the end or start track point is reached, i-Pilot automatically exits from the Track to Start or Track to End function. During track playback, i-Pilot takes control over all steering functions;

speed can be manually controlled or the Cruise Control function can also 56 minnkotamotors.com TRACK RECORDING / PLAYBACK START RECORDED TRACK END be used. The motor speed must be set high enough in order to stay on the track given wind, current and other external forces. i-Pilot can also pause the recording of a track. When the recording is paused, i-Pilot temporarily stops recording any new track points. When track recording is resumed, i-Pilot records new track points. Due to the nature of pausing a recording, there may be a large separation distance between two track points or two track points lying on top of one another where the pause occurred. This can cause erratic motor steering therefore it is very important to know where the pause button was pressed and to resume the recording just ahead of that location. If while paused, the separation distance exceeds a quarter mile, the recording will automatically stop. minnkotamotors.com minnkotamotors.com 57 RECORDING A TRACK 1. Press 2. The Memory Location icon will ash on the remote LCD for three on the remote. seconds, allowing you to choose a memory location by pressing or Pressing again or waiting for three seconds accepts the memory location. 3. The REC icon will be displayed on the remote LCD. Remember this will be the start point on the track. 4. Navigate the boat along the desired path or course. AutoPilot and/or Cruise Control can be used while recording a track. 5. Press on the remote again to stop the recording. The recording will end automatically if the two-mile distance limit is reached for the track or if one of the following buttons are pressed:

or

. 58 minnkotamotors.com minnkotamotors.com TRACK RECORDING / PLAYBACK PAUSE AND RESUME A RECORDING 1. While recording a track press 2. The record icon will ash on the

. remote LCD. 3. i-Pilot has now paused the recording of the track. 4. If the boat moves farther than a quarter mile from where was pressed, the recorded track will be ended and saved to the memory location previously selected. 5. When ready to resume recording, navigate the boat just was pushed. Failure to do this may ahead of where cause erratic play back of a track. 6. Push 7. The record icon will stop ashing on the

. remote LCD. 8. i-Pilot is now recording again and adding to the track that was paused. minnkotamotors.com minnkotamotors.com 59 START RECORDED TRACK ENGAGE TRACK TO START ENGAGE TRACK TO END END i-PilotTIPS You can switch directly between Track to Start and Track to End. This allows you to concentrate on productive sections of a track. 60 minnkotamotors.com minnkotamotors.com TRACK RECORDING / PLAYBACK REPLAYING A TRACK

(TRACK TO START / TRACK TO END) 1. Manually navigate the boat to within a quarter mile of the saved track. Due to safety reasons, i-Pilot will not re-engage a saved track greater than a quarter mile away. 2. Press 3. The Memory Location icon will ash on on the remote. or the remote LCD for three seconds, allowing you to choose a memory location by pressing button pressed in step 2 again or waiting for three seconds accepts the memory location. Pressing the or 4. Adjust motor speed to desired setting to engage and navigate track automatically. RECORD, TRACK TO END AND TRACK TO START ESCAPE 1. If is accidentally hit, press onds on the remote to cancel the command. or within three sec-

Steering left or right and turning Advanced AutoPilot on with the foot pedal will disengage Track to Start or Track to End. minnkotamotors.com minnkotamotors.com 61 FREQUENTLY ASKED QUESTIONS Q. Does i-Pilot record the speed I am traveling when recording a track?

A. No. i-Pilot only records its location during track record. It is up to the user to set the desired speed manually or with Cruise Control. Q. Why doesnt my GPS Signal Strength icon always show all four bars?

A. GPS signal strength is impacted by many inuences including:

i-Pilot controller having a clear view of the sky (especially to the southern sky), boat being located alongside a high bank and your geographic location. Is i-Pilot compatible with CoPilot?

Q. A. No. None of the components between the two systems are compatible with each other. Q. Does the remote oat?

A. Yes. Q. When I turn on the remote, the Low Battery Indicator comes on along with all the other icons, is my battery low?

A. Not necessarily. When the remote rst powers up, all of the icons come on automatically for a short period of time. This gives the user the opportunity to view all of the icons. Q. How long of a track can I record?

A. Each individual track location (A, B or C) can be up to two miles in length. 62 minnkotamotors.com minnkotamotors.com Q. Can I use multiple remotes with my i-Pilot?

A. Yes, you can use an unlimited number of remotes simultaneously. Remember to learn each new remote to the i-Pilot controller. Q. Why does the LCD screen of the remote have dark blotches on it when I wear my sunglasses?

A. Polarized sunglasses can dramatically affect the way an LCD looks to the human eye. Q. Can I control how fast i-Pilot takes me back to a Spot Lock location when using Spot Lock Recall?

A. No, Spot Lock and Spot Lock Recall are fully automatic functions that take full control of motor steering and speed. Q. Where can I purchase additional remotes?

A. Your local Minn Kota retailer should carry additional remotes. If I turn off the remote, will i-Pilot continue to operate?

Q. A. Yes. The i-Pilot Controller will continue in its current state of operation until the user makes a change either with the remote or foot pedal (Terrova only). Q. Where are the three tracks and Spot Lock locations stored?

A. In the i-Pilot Controller. minnkotamotors.com minnkotamotors.com 63 TROUBLESHOOTING General Troubleshooting Problem: The motor is making erratic steering corrections while in AutoPilot, Spot Lock or Track to Start/End. Solution: Be sure to keep all ferrous metallic objects away from the i-Pilot controller as they will have an impact on the built-in compass. Such objects include: anchors, metal framework, etc. Problem: When a button on the remote is pressed the motor doesnt always respond. Solutions: Check if the low battery indicator is on. If so, replace the remotes battery. Check for large obstructions between the remote and the motor. Problem:

Solution:

I press a button on the remote and nothing happens. Could be a dead battery in the remote. If the battery was just replaced, open the remote case and verify that all the internal components were properly reinstalled. Problem:

I press a button on the remote and all the icons come on for a few seconds then it shuts off. Solutions: Verify that the motor is powered up (for Terrova and Riptide ST, it must also have its system ready light on). Go through the learn process for the remote (see page 33 for the procedure). Problem:

Solution:

i-Pilot wont let me turn on certain features like: Advanced AutoPilot, Record, Track to Start/End or Spot Lock. Verify that the GPS Signal Strength icon on the LCD shows at least one bar. If there are no bars, i-Pilot will not allow these GPS-based features to be enabled. 64 minnkotamotors.com minnkotamotors.com Problem: The remote LCD backlighting will not come on. Solution:

Check if the low battery indicator icon is on. Backlighting is disabled when a low battery level is detected. Replace the battery. The Backlight will not come on if the remote is not currently communicating with the i-Pilot Controller. Solution:

Spot Lock Problem: The boat doesnt seem to keep close enough to the recorded Solution:

Solution:

Solution:

Spot Lock location. Verify the trolling motor batteries are sufciently charged Check for weeds on the prop. In more extreme wind and current conditions, the boat will tend to stabilize a little ways down wind from the intended location. Relock the location the same distance upwind and expect that the boat will drift some in the downwind direction. Cruise Control Problem: The GPS speed displayed on the remote is different than Solution:

what my other GPS system shows. If you are using Cruise Control with Advanced AutoPilot or Track to Start/End, i-Pilot calculates the actual speed in the intended direction of travel which may differ from your GPS reported speed. Problem: Cruise Control isnt holding the target speed close enough. Solution:

Verify the trolling motor batteries are sufciently charged. minnkotamotors.com minnkotamotors.com 65 AutoPilot Problem: When in Advanced AutoPilot in strong winds, there is quite a bit of back and forth movement in the boat. Solution: While Advanced AutoPilot will keep your boat on a true heading, it may be at the expense of the boat having to continuously move to get back on the correct course. In these extreme conditions you may be better off using AutoPilot and correcting for the wind manually. Problem:

Solution:

I press and release the Advanced AutoPilot button and the system goes into AutoPilot instead of Advanced AutoPilot. If the GPS Signal Strength indicator shows no bars, then pressing and releasing the AutoPilot button will enable AutoPilot automatically instead of requiring that the button be held for two to three seconds like when GPS is present. Track Record and Playback Problem: While in Track to Start/End the propeller suddenly stopped. Verify you did not accidentally enable another automatic feature Solution:

such as AutoPilot or Spot Lock. Solution: When the end (or start) of the track is achieved during playback, i-Pilot will automatically turn off the motor along with canceling Track to Start/End. Problem: While in Record mode, the recording suddenly stopped. Solution:

You may have reached the two mile limit for recording a track. 66 minnkotamotors.com minnkotamotors.com Terrova/Riptide ST:

Problem: Pressing a button on the remote causes all the icons to come on for a few seconds then they all go off. Solution:

Ensure the motor is deployed and that the System Ready light Solution:

Solution:

Solution:

on the motor is illuminated. Verify that the i-Pilot controller is properly plugged in. Try to relearn the remote to the controller. Cycle power to the motor by stowing and deploying the motor verifying that the System Ready light comes back on when the motor is deployed PowerDrive V2 /Riptide SP:

Problem: Pressing a button on the remote causes all the icons to come Solution:

Solution:

Solution:

on for a few seconds then they all go off. Verify that the i-Pilot controller is properly plugged into the footpedal connector on the motor. Try to relearn the remote to the controller. Cycle power to the motor. Problem: Steering does not work properly or at all. Solution:

Verify that the steering wires from the i-Pilot cable are properly connected directly to the two-wire cable coming from the steering housing. minnkotamotors.com minnkotamotors.com 67 p p p p g djustable in increments. errova: The Terrova is the latest family of bow-mount, electric-steer trolling motors from Minn Kot GLOSSARY Accessory Connector: The accessory connector is a small sealed connector used on the Terrova and Riptide ST family of motors. This connector allows for easy waterproof installation of any Minn Kota Terrova and Riptide ST accessories. Center Housing: A plastic center housing exists in the center of the trolling motor mount. This center housing covers and protects mechanical and electrical components from the environment. The center housing is temporarily removed from PowerDrive V2 and Riptide SP motors during i-Pilot installation. CoPilot: Co-Pilot a wireless motor control accessory from Minn Kota available for all Terrova, PowerDrive V2, Riptide ST and Riptide SP lines of motors. The accessory allows for wireless adjustment of all basic motor control functions. The Co-Pilot accessory must be removed from a PowerDrive V2 and Riptide SP motor upon i-Pilot installation. Any Co-Pilot accessory installed on a Terrova or Riptide ST motor is electrically disabled once i-Pilot is installed. Control Box Cover: The control box cover is a plastic cover installed on the top head of the motor. The cover protects the inner wiring and electronics from the environment. This part is replaced by the i-Pilot controller. GPS: GPS is an acronym for Global Positioning System. GPS provides accurate position (latitude, longitude, altitude) information virtually anywhere on the earth through satellite technology and personal receivers on the ground. A series of geosynchronous satellites broadcast a unique signal toward the earth once per second. A GPS receiver, which is used in i-Pilot, receives the signals from these satellites and is able to determine position based on very slight differences in the time each signal is received and the receivers knowledge of the location of each of the satellites. GPS Speed: The speed calculated by measuring the boats change in geographical location over a given time using GPS data. i-Pilot Controller: The i-Pilot controller is part of the i-Pilot system. The controller contains a GPS receiver, compass and electronics to automatically navigate the trolling motor. The controller resembles a motor control box 68 minnkotamotors.com ta. The motor can be identied by the Terrova name on the side of the trolling motor mount. cover and is completely sealed and waterproof. The controller replaces the existing control box cover and AutoPilot controller if one is present. i-Pilot Controller Cable: On PowerDrive V2 and Riptide SP versions of i-Pilot, a cable exists on the bottom side of the i-Pilot controller. This cable is designed to connect to the foot pedal input cable at the base of the motor for a waterproof connection. i-Pilot Controller Connector: On the Terrova and Riptide ST versions of i-Pilot, a connector exists on the bottom side of the i-Pilot controller. This connecter is designed to connect to the accessories connector for an easy waterproof connection. Motor Speed: The speed that the prop is rotating from 0 to 10, which is adjustable in increments. PowerDrive V2: The PowerDrive V2 is in the latest family of bow-mount, electric-steer trolling motors from Minn Kota. The motor can be identied by the PowerDrive V2 name on the side of the trolling motor mount. Riptide SP: The Riptide SP is in the latest family of saltwater bow-mount, electric-steer trolling motors from Minn Kota. The motor can be identied by the Riptide SP name on the side of the trolling motor mount. Riptide ST: The Riptide ST is in the latest family of saltwater bow-mount, electric-steer trolling motors from Minn Kota. The motor can be identied by the Riptide ST name on the side of the trolling motor mount. Side Plates: Side plates exists on each side of the trolling motor mount. These side plates cover and protect mechanical and electrical components from the environment. The side plates are temporarily removed from PowerDrive V2 and Riptide SP motors during i-Pilot installation. Terrova: The Terrova is in the latest family of bow-mount, electric-steer trolling motors from Minn Kota. The motor can be identied by the Terrova name on the side of the trolling motor mount. Track End: The last point on a recorded track, which is made when Track Recording was ended. Track Start: The rst point on a recorded track, which is made when the Track Record button is pressed to start a recording. minnkotamotors.com 69 COMPLIANCE STATEMENTS ENVIRONMENTAL COMPLIANCE STATEMENT:

It is the intention of Johnson Outdoors Inc. to be a responsible corporate citizen, operating in compliance with known and applicable environmental regulations and a good neighbor in the communities where we make or sell our products. WEEE Directive:

EU Directive 2002/96/EC Waste of Electrical and Electronic Equipment Directive (WEEE) impacts most distributors, sellers and manufacturers of consumer electronics in the European Union. The WEEE Directive requires the producer of consumer electronics to take responsibility for the management of waste from their products to achieve environmentally responsible disposal during the product life cycle. WEEE compliance may not be required in your location for electrical and electronic equipment (EEE), nor may it be required for EEE designed and intended as xed or temporary installation in transportation vehicles such as automobiles, aircraft and boats. In some European Union member states, these vehicles are considered outside of the scope of the Directive, and EEE for those applications can be considered excluded from the WEEE Directive requirement. This symbol (WEEE wheelie bin) on product indicates the product must not be disposed of with other household refuse. It must be disposed of and collected for recycling and recovery of waste EEE. Johnson Outdoors Inc. will mark all EEE products in accordance with the WEEE Directive. It is our goal to comply in the collection, treatment, recovery and environmentally sound disposal of those products; however, these requirement do vary within European Union member states. For more information about where you should dispose of your waste equipment for recycling and recovery and/or your European Union member state requirements, please contact your dealer or distributor from which your product was purchased. FEATURES CAR ACTRISTIQUES DCLARATION DE CONFORMIT ENVIRONNEMENTALE :

Johnson Outdoors Inc. a lintention dtre une corporation responsable, fonctionnant en conformit avec les rglements environnementaux connus et applicables, et dagir en tant que bon voisin dans les communauts o nous fabriquons ou vendons nos produits. Directive WEEE :

La Directive 2002/96/EC de lUnion europenne traitant des dchets dquipement lectriques et lectroniques, soit Waste of Electrical and Electronic Equipment (WEEE), affecte la plupart des distributeurs, vendeurs et fabriquants de produits lectroniques dans lUnion europenne. La directive WEEE demande que le fabriquant de produits lectroniques se charge de la grance des dchets provenant de leurs produits an de sen dbarrasser dune manire responsable par rapport lenvironnement au cours du cycle de vie du produit. Respecter la directive WEEE peut ne pas tre exig o vous vous trouvez en ce qui concerne lquipement lectrique et lectronique (EEE), comme ne pas tre exig pour lquipement lectrique et lectronique conu et destin des installations temporaires ou permanentes dans les vhicules de transport comme les automobiles, avions et bateaux. Dans quelques pays membres de lUnion 70 minnkotamotors.com Applicant: Johnson Outdoors, Inc. Model Number Description 2994085 1866200 1866205 1866210 1866215 I PILOT REMOTE I PILOT SYSTEM, TERROVA I PILOT SYSTEM, ST I PILOT SYSTEM, PD V2 I PILOT SYSTEM, SP FCC ID:

Remote T62-IPREM Controller T62-IPCON Industry Canada ID:

Remote 4397A-IPREM Controller 4397A-IPCON FCC Compliance Statement:

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. minnkotamotors.com 71 72 minnkotamotors.com HALF THE CHARGE TIME AT HALF THE WEIGHT. When batteries fail, most anglers blame overuse. But improper charging causes battery failure more than any other factor. Our all-new high-frequency, digital microprocessor design is more compact, up to 50% lighter, and engineered to extend battery life and deliver up to 50% faster charging time. You invest a lot in your batteries: time, money and the opportunity to catch more sh. Protect that investment with our all-new line of Precision Chargers. NEW MK 110PC NEW MK 220PC NEW MK 330PC NEW PRECISION CHARGE ON-BOARD CHARGERS. All Minn Kota Precision Chargers feature:

High-frequency, digital microprocessor design charges up to 50% faster than other chargers

Low-line voltage compensation, automatic temperature compensation and multi-stage charging

On demand battery equalization to prevent sulfation build up on plates and extend battery life to deliver the perfect charge NEW MK 440PC NOT SHOWN MKA-23 RTA-19 MKA-21 MKA-32 RTA-17 Cover included with quick release bracket. COMPOSITE QUICK RELEASE BRACKETS (MKA-21, MKA-23, RTA-17, RTA-19) Allows for easy removal of any Terrova, PowerDrive V2, PowerDrive or Pontoon HC (MKA-21); Maxxum, Maxxum Pro, All Terrain or Edge (MKA-23); Riptide ST or Riptide SP (RTA-17); or Riptide SM or Riptide SE (RTA-19) bow-mount motor. High-yield composite construction is super strong and impervious to corrosion. Low-profile design leaves deck clear when motor is removed. Locking handle with stainless steel pins can be secured with padlock (not included). ELECTRIC STEER QUICK RELEASE BRACKET WITH COVER (MKA-32) Designed for fast removal of any Terrova, PowerDrive V2 or PowerDrive bow-mount trolling motor. New cam-lock design features ultra-tight tolerances that eliminate bracket movement and noise. Locking lever includes pin and lanyard. Upper and lower plates include slot for securing with padlock (not included). Includes composite cover that attaches to lower half of bracket when motor is removed, keeping the deck profile clean. minnkotamotors.com 73 NOTES 74 minnkotamotors.com NOTES minnkotamotors.com 75 minnkotamotors.com MINN KOTA CONSUMER

& TECHNICAL SERVICE P.O. Box 8129 Mankato, MN 56002 121 Power Drive Mankato, MN 56001 Phone (800) 227-6433 Fax (800) 527-4464