a module solution provider WG1400-00 TI CC3100 IEEE 802.11 b/g/n Datasheet Draft 0.5 Nov/25/2015 Prepared By Reviewed By Approved By Copyright JORJIN TECHNOLOGIES INC. 2015 http://WWW.JORJIN.COM.TW CONFIDENTIAL Doc No: WG1400-00-DTS-D05 Index 1. OVERVIEW ............................................................................................................................... 2 General Features ............................................................................................... 2 Applications ....................................................................................................... 3 MODULE BLOCK DIAGRAM ................................................................................................. 4 PRODUCTION SPECIFICATIONS .......................................................................................... 5 Absolute Maximum ratings ............................................................................... 5 Recommended Operating Conditions ........................................................... 5 Electrical characteristics ................................................................................... 5 WLAN RF Specifications .................................................................................... 6 SPI Interface ....................................................................................................... 7 Input Clocks/Oscillators .................................................................................... 8 Current Consumption ....................................................................................... 8 REFERENCE SCHEMATICS ..................................................................................................... 9 PIN OUT (TOP VIEW) ............................................................................................................ 10 Pin Description ................................................................................................. 11 Package Information ...................................................................................... 13 RF Connector ................................................................................................... 14 MODULE MECHANICAL OUTLINE ..................................................................................... 15 SMT AND BAKING RECOMMENDATION ......................................................................... 16 Baking Recommendation .............................................................................. 16 SMT RECOMMENDATION ....................................................................................... 16 HISTORY CHANGE ............................................................................................................... 17 2. 3. 1.1. 1.2. 3.1. 3.2. 3.3. 3.4. 3.5. 3.6. 3.7. 4. 5. 5.1. 5.2. 5.3. 6. 7. 7.1. 7.2. 8. Copyright JORJIN TECHNOLOGIES INC. 2015 Page 1 http://WWW.JORJIN.COM.TW CONFIDENTIAL Doc No: WG1400-00-DTS-D05 1. OVERVIEW 1.1. General Features
WIFI Network Processor Subsystems
Featuring Wi-Fi Internet-On-a-Chip
Wi-Fi Driver and Multiple Internet Protocols in ROM
802.11 b/g/n Radio, Baseband, and MAC, Wi-Fi Driver, and Supplicant Powerful Crypto Engine for Fast, Secure Wi-Fi and Internet Connections with 256-Bit AES Encryption for TLS and SSL Connections
Station, AP, and Wi-Fi Direct Modes
WPA2 Personal and Enterprise Security
SimpleLink Connection Manager for Autonomous and Fast Wi-Fi Connections Smart Config Technology, AP Mode, and WPS2 for Easy and Flexible Wi-Fi Provisioning
Application Throughput
- UDP : 16 Mbps
- TCP : 12 Mbps
Host Interface
Interfaces with 8-, 16-, and 32-bit MCU or ASICs Over SPI or UART Interface Low External Host Driver Footprint: Less Than 7 KB of Code Memory and 700 B of RAM Memory Required for TCP Client Application
SimpleLink Advanced Features
Embedded Wi-Fi Connection Manager with No Host Processor involvement Smart Config Provisioning Utility to Configure Headless Devices Using a Smart Phone with a Single Click
BSD Socket APIs for Standard and Easy Internet Applications Development
Powerful HW Crypto Engine for Fast State- of-the-Art Wi-Fi and Internet Security
Programmable Packet Filters in MAC and IP Layer to Optimize Power Consumption
Power Management Subsystem
Integrated DC-DC Supports a Wide Range of Supply Voltage:
- VBAT Wide-Voltage Mode : 2.3 to 3.6 V Copyright JORJIN TECHNOLOGIES INC. 2015 Page 2 http://WWW.JORJIN.COM.TW CONFIDENTIAL Doc No: WG1400-00-DTS-D05
Advanced Low-Power Modes
- Hibernate with RTC: 4 A
-
Low-Power Deep Sleep (LPDS): 115 A
- RX Traffic (MCU Active): 53 mA @ 54 OFDM
- TX Traffic (MCU Active): 223 mA @ 54 OFDM, Maximum Power
-
Idle Connected: 690 A @ DTIM = 1
Clock Source
40.0-MHz internal built-in crystal 32.768-kHz external clock source
Package and Operating Temperature
23.5mm*23.5mm*2.4mm
Ambient Temperature Range: -30C to 85C 1.2. Applications For Internet-of-Things applications, such as:
Home Automation and Security
Cloud Connectivity
Smart Energy
Industrial Control
Access Control
Smart Plug and Metering
Wireless Audio
IP Network Sensor Nodes Copyright JORJIN TECHNOLOGIES INC. 2015 Page 3 http://WWW.JORJIN.COM.TW CONFIDENTIAL Doc No: WG1400-00-DTS-D05 2. MODULE BLOCK DIAGRAM Fig 2.1 WG1400-00 module block diagram Copyright JORJIN TECHNOLOGIES INC. 2015 Page 4 http://WWW.JORJIN.COM.TW CONFIDENTIAL Doc No: WG1400-00-DTS-D05 3. PRODUCTION SPECIFICATIONS 3.1. Absolute Maximum ratings
Over operating free-air temperature range PARAMETERS VBAT Digital inputs RF pins Analog pins (Clock input) Operating temperature range (TA) 3.2. Recommended Operating Conditions PINS 3,4,6 MIN MAX UNIT
-0.5
-0.5
-0.5
-0.5
-30 3.8 VBAT+0.5 2.1 2.1
+85 V V V V C
Over operating free-air temperature range (1) PARAMETERS PINS CONDITIONS(2) VBAT 3,4,6 Direct battery connection Ambient thermal slew MIN 2.3
-20 TYP 3.3 MAX UNIT 3.6 20 V C /minute
(1) Operating temperature is limited by crystal frequency variation.
(2) To ensure WLAN performance, ripple on the 2.1- to 3.3-V supply must be less than 300 mV. 3.3. Electrical characteristics
3.3 V, 25C PARAMETER MIN NOM CIN Pin capacitance VIH High-level input voltage VIL Low-level input voltage IIH High-level input current IIL Low-level input current VOH High-level output voltage
(VBAT_IN = 3.0V) VOL Low-level output voltage 0.65 VBAT_IN
-0.5 2.4 4 5 5 MAX 0.4 VBAT_IN + 0.5 V 0.35 VBAT_IN UNIT pF V V nA nA V V Copyright JORJIN TECHNOLOGIES INC. 2015 Page 5 http://WWW.JORJIN.COM.TW CONFIDENTIAL Doc No: WG1400-00-DTS-D05
(VBAT_IN = 3.0V) IOH High-level source current, VOH = 2.4 IOL Low-level sink current, VOH = 0.4 6 6 mA mA Pin internal Pull up and Pull down (25C)))) PARAMETER MIN NOM MAX UNIT IOH Pull-Up current, VOH = 2.4
(VBAT_IN = 3.0V) IOH Pull-Down current, VOL = 0.4
(VBAT_IN = 3.0V) 3.4. WLAN RF Specifications 5 5 10 A A
WLAN Receiver Characteristics Parameter Condition (Mbps) Min Sensitivity
(8% PER for 11b rates, 10% PER for 11g/11n rates)(10% PER) Maximum input level (10% PER) 1 DSSS 11 CCK 6 OFDM 54 OFDM MCS0 MCS7 802.11b 802.11g Typ
-92.5
-86.3
-86.1
-71.2
-84.1
-67.3
-4.0
-10.0 Max Units dBm
WLAN Transmitter Characteristics Parameter Condition Min Typ Max Units Maximum RMS output power measured at 1 dB from IEEE spectral mask or EVM Output power accuracy Transmit center frequency accuracy 1 DSSS 11 CCK 6 OFDM 54 OFDM MCS0 MCS7
-2
-25 16.0 16.0 15.5 12.5 15.0 11.0 dBm 2 25 dB ppm
(1) Channel-to-channel variation is up to 2dB. The edge channels (2412 and 2472MHz) have reduced TX power to meet FCC emission limits. Copyright JORJIN TECHNOLOGIES INC. 2015 Page 6 http://WWW.JORJIN.COM.TW CONFIDENTIAL Doc No: WG1400-00-DTS-D05 3.5. SPI Interface
Host SPI Interface timing Fig 3.5.1 Host SPI interface timing Table 3.5.1 Host SPI interface timing parameter Parameter Parameter (1) Parameter Name Min Max Unit Number I1 I2 I3 I4 I5 I6 I7 I8 I9 F tdk tLP tHT D tIS tIH tOD tOH Clock frequency @ VBAT = 3.3V Clock period Clock low period Clock high period Duty cycle RX data setup time RX data hold time TX data output delay TX data hold time 50 45 4 4 20 25 25 55 20 24 MHz ns ns ns
%
ns ns ns
(1) The timing parameter has a maximum load of 20 pF at 3.3 V. Copyright JORJIN TECHNOLOGIES INC. 2015 Page 7 http://WWW.JORJIN.COM.TW CONFIDENTIAL Doc No: WG1400-00-DTS-D05 3.6. Input Clocks/Oscillators Table 3.6.1 External RTC Digital Clock Requirements CHARACTERISTICS CONDITION SYM MIN TYP MAX UNIT Frequency Frequency accuracy
(Initial + temp + aging) Input transition time tr/tf (10% to 90%) Frequency input duty cycle Slow clock input voltage limits Square wave, DC coupled Input impedance 3.7. Current Consumption tr/tf Vih Vil 32768 20 50 0.65 VBAT 0 1 150 100 80 VBAT 5 0.35 VBAT Hz ppm ns
%
V Vpeak M pF Mode Condition Typical Current at 3.3V Active Mode 11 Mbps TX at 16dBm 54 Mbps TX at 12.5dBm RX at 54Mbps Low Power Mode LPDS (low-power deep sleep) Hibernate 240mA 185mA 51mA 100A 4A Copyright JORJIN TECHNOLOGIES INC. 2015 Page 8 http://WWW.JORJIN.COM.TW CONFIDENTIAL Doc No: WG1400-00-DTS-D05 4. REFERENCE SCHEMATICS Copyright JORJIN TECHNOLOGIES INC. 2015 Page 9 http://WWW.JORJIN.COM.TW CONFIDENTIAL Doc No: WG1400-00-DTS-D05 5. PIN OUT (TOP VIEW) Page 10 Copyright JORJIN TECHNOLOGIES INC. 2015 http://WWW.JORJIN.COM.TW CONFIDENTIAL Doc No: WG1400-00-DTS-D05 5.1. Pin Description Signal Name State at Type Description Pin No. 1 2 GND nRESET 3 4 5 6 7 8 9 VBAT_IN VBAT_IN GND NC_06 GND EXT_RTC_IN UART_RTS 10 UART_TX 11 UART_RX 12 UART_CTS 13 NC_13 14 NC_14 15 NC_15 16 NC_16 17 NC_17 18 NC_18 19 HIBERNATE Reset GND HI-Z POW POW GND HI-Z GND HI-Z HI-Z HI-Z HI-Z HI-Z HI-Z HI-Z HI-Z HI-Z HI-Z HI-Z HI-Z GND Ground. I RESET input for the device. Active low input. The RC circuit (100K 0.1F) has been built in internal for power reset. Ground. Ground. POW POW GND NA GND Power supply input, 2.1 to 3.6V. Power supply input, 2.1 to 3.6V. Unused. Leave unconnected. Analog 32.768-KHz / External clock input. O O I I NA NA NA NA NA NA I UART host interface. Connect to test point on prototype for flash programming. UART host interface. Connect to test point on prototype for flash programming. UART host interface. Connect to test point on prototype for flash programming. UART host interface. Connect to test point on prototype for flash programming. Unused. Leave unconnected. Unused. Leave unconnected. Unused. Leave unconnected. Unused. Leave unconnected. Unused. Leave unconnected. Unused. Leave unconnected. Hibernate signal input to the NWP
(active low). If the Hibernate function Page 11 Copyright JORJIN TECHNOLOGIES INC. 2015 http://WWW.JORJIN.COM.TW CONFIDENTIAL Doc No: WG1400-00-DTS-D05 20 NC_20 21 FORCE_AP HI-Z HI-Z NA I is not used, connect to VBAT using 100K for pulling-up. Unused. Leave unconnected. For forced AP mode, pull high on the board using 100K resistor. Otherwise, pull down to ground using 100K resistor. 22 GND GND GND Ground. 23 HOST_SPI_CLK 24 HOST_SPI DIN 25 HOST_SPI_DOUT 26 HOST_SPI_CS 27 HOST_IRQ 28 ANT_SEL_1 29 ANT_SEL_2 30 TCXO_EN/SOP2 31 NC_31 32 NC_32 33 GND 34 GND 35 GND HI-Z HI-Z HI-Z HI-Z HI-Z HI-Z HI-Z HI-Z HI-Z HI-Z GND GND GND O I O I O O O O NA NA GND GND GND Host interface SPI clock. Host interface SPI data input. Host interface SPI data output. Host interface SPI chip select. Interrupt output. Antenna selection control. For future use only. Antenna selection control. For future use only. Pull down to ground using 100K resistor Unused. Leave unconnected. Unused. Leave unconnected. Ground. Ground. Ground. Page 12 Copyright JORJIN TECHNOLOGIES INC. 2015 http://WWW.JORJIN.COM.TW CONFIDENTIAL Doc No: WG1400-00-DTS-D05 5.2. Package Information
Top view (Unit: mm)
Bottom view (Unit: mm) Page 13 Copyright JORJIN TECHNOLOGIES INC. 2015 http://WWW.JORJIN.COM.TW CONFIDENTIAL Doc No: WG1400-00-DTS-D05 5.3. RF Connector
P/N : U.FL-R-SMT-1 (U.FL Series) from HIROSE. Fig 5.3.1 RF connector drawing
Table for Filed Antenna Page 14 Copyright JORJIN TECHNOLOGIES INC. 2015 http://WWW.JORJIN.COM.TW CONFIDENTIAL Doc No: WG1400-00-DTS-D05 6. MODULE MECHANICAL OUTLINE Page 15 Copyright JORJIN TECHNOLOGIES INC. 2015 http://WWW.JORJIN.COM.TW CONFIDENTIAL Doc No: WG1400-00-DTS-D05 7. SMT AND BAKING RECOMMENDATION 7.1. Baking Recommendation
Baking condition
- Follow MSL Level 4 to do baking process.
- After bag is opened, devices that will be subjected to reflow solder or other high temperature process must be a) Mounted within 72 hours of factory conditions <30C/60% RH, or b) Stored at <10% RH.
- Devices require bake, before mounting, if Humidity Indicator Card reads >10%
If baking is required, Devices may be baked for 8 hrs. at 125 C. 7.2. SMT Recommendation
Recommended Reflow profile Page 16 Copyright JORJIN TECHNOLOGIES INC. 2015 http://WWW.JORJIN.COM.TW CONFIDENTIAL Doc No: WG1400-00-DTS-D05 No. Item Temperature (C) Time (sec) Pre-heat Soldering Peak-Temp. D1: 140 ~ D2: 200 T1: 80 ~ 120 D2: = 220 T2: 60 +/- 10 D3: 250 C max 1 2 3 Note: (1) Reflow soldering is recommended two times maximum.
(2) Add Nitrogen while Reflow process SMT solder ability will be better.
Stencil thickness 0.1~ 0.13 mm (Recommended)
Soldering paste (without Pb) Recommended SENJU N705-GRN3360-K2-V can get better soldering effects. 8. HISTORY CHANGE Revision Date Description 2014/10/14 Initial Released 2015/03/13 1. Revise RF Specifications. 2. Redraw reference schematic. 3. Add Recommended Operating Conditions. 4. Add SMT AND BAKING RECOMMENDATION 2015/04/24 Revise the Ambient Temperature Range 2015/05/06 1. Add RF connector. 2. Revise the Recommended Operating Conditions. 2015/11/25 1. Add FCC statement. 0.1 0.2 0.3 0.4 0.5 Page 17 Copyright JORJIN TECHNOLOGIES INC. 2015 http://WWW.JORJIN.COM.TW CONFIDENTIAL Doc No: WG1400-00-DTS-D05 FCC Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. FCC Radiation Exposure Statement This device complies with FCC radiation exposure limits set forth for an uncontrolled environment and it also complies with Part 15 of the FCC RF Rules. This equipment must be installed and operated in accordance with provided instructions and the antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter. End-users and installers must be provided with antenna installation instructions and consider removing the no-collocation statement. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired operation. This device is intended only for OEM integrators under the following conditions:
1) The antenna must be installed such that 20cm is maintained between the antenna and users, and 2) The transmitter module may not be co-located with any other transmitter or antenna, 3) For all products market in US, OEM has to limit the operation channels in CH1 to CH11 for 2.4Gband by supplied firmware programming tool. OEM shall not supply any tool or info to the end-user regarding to Regulatory Domain change. Page 18 Copyright JORJIN TECHNOLOGIES INC. 2015 http://WWW.JORJIN.COM.TW CONFIDENTIAL Doc No: WG1400-00-DTS-D05 As long as 3 conditions above are met, further transmitter test will not be required. However, the OEM integrator is still responsible for testing their end-product for any additional compliance requirements required with this module installed. IMPORTANT NOTE:
In the event that these conditions can not be met (for example certain laptop configurations or co-location with another transmitter), then the FCC authorization is no longer considered valid and the FCC ID can not be used on the final product. In these circumstances, the OEM integrator will be responsible for re-evaluating the end product (including the transmitter) and obtaining a separate FCC authorization. End Product Labelling The final end product must be labelled in a visible area with the following:
Contains FCC ID:WS2-WG1400-00. Manual Information to the End User The OEM integrator has to be aware not to provide information to the end user regarding how to install or remove this RF module in the users manual of the end product which integrates this module. Caution!
Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. Page 19 Copyright JORJIN TECHNOLOGIES INC. 2015 http://WWW.JORJIN.COM.TW CONFIDENTIAL Doc No: WG1400-00-DTS-D05 Canada Statement This device complies with Industry Canadas licence-exempt RSSs. Operation is subject to the following two conditions:
(1) This device may not cause interference; and
(2) This device must accept any interference, including interference that may cause undesired operation of the device. Le prsent appareil est conforme aux CNR dIndustrie Canada applicables aux appareils radio exempts de licence. Lexploitation est autorise aux deux conditions suivantes :
(1) lappareil ne doit pas produire de brouillage;
(2) lutilisateur de lappareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible den compromettre le fonctionnement. The device meets the exemption from the routine evaluation limits in section 2.5 of RSS 102 and compliance with RSS-102 RF exposure, users can obtain Canadian information on RF exposure and compliance. Le dispositif rencontre l'exemption des limites courantes d'valuation dans la section 2.5 de RSS 102 et la conformit l'exposition de RSS-102 rf, utilisateurs peut obtenir l'information canadienne sur l'exposition et la conformit de rf. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. This equipment should be installed and operated with a minimum distance of 20 centimeters between the radiator and your body. Cet metteur ne doit pas tre Co-plac ou ne fonctionnant en mme temps qu'aucune autre antenne ou metteur. Cet quipement devrait tre install et actionn avec une distance minimum de 20 centimtres entre le radiateur et votre corps. This device is intended only for OEM integrators under the following conditions:
1) The antenna must be installed such that 20cm is maintained between the antenna and users, and 2) The transmitter module may not be co-located with any other transmitter or antenna, 3) For all products market in Industry Canada, OEM has to limit the operation channels in CH1 to CH11 for 2.4Gband by supplied firmware programming tool. OEM shall not supply any tool or info to the end-user regarding to Regulatory Domain change. Page 20 Copyright JORJIN TECHNOLOGIES INC. 2015 http://WWW.JORJIN.COM.TW CONFIDENTIAL Doc No: WG1400-00-DTS-D05 As long as 3 conditions above are met, further transmitter test will not be required. However, the OEM integrator is still responsible for testing their end-product for any additional compliance requirements required with this module installed. Cet appareil est conu uniquement pour les intgrateurs OEM dans les conditions suivantes:
1) L'antenne doit tre install de telle sorte que 20 cm est maintenue entre l'antenne et les utilisateurs, et 2) Le module metteur peut pas tre co-localis avec un autre metteur ou antenne, 3) Pour tout march des produits d'Industrie Canada, OEM doit limiter les canaux de coopration dans CH1 CH11 pour 2.4Gband par l'outil de programmation du firmware fourni. OEM ne doit pas fournir un outil ou d'information l'utilisateur final en ce qui concerne le changement de domaine rglementaire. Tant que 3 conditions ci-dessus sont remplies, autre test de l'metteur ne sera pas ncessaire. Cependant, l'intgrateur OEM est toujours responsable de tester leur produit final pour toutes les exigences de conformit supplmentaires ncessaires avec ce module install. IMPORTANT NOTE:
In the event that these conditions can not be met (for example certain laptop configurations or co-location with another transmitter), then the IC authorization is no longer considered valid and the IC ID can not be used on the final product. In these circumstances, the OEM integrator will be responsible for re-evaluating the end product (including the transmitter) and obtaining a separate IC authorization. Dans le cas o ces conditions ne peuvent tre remplies (par exemple certaines configurations d'ordinateurs portables ou de co-localisation avec un autre metteur), puis l'autorisation IC est plus considr comme valide et l'ID IC ne peut pas tre utilis sur le produit final. Dans ces circonstances, l'intgrateur OEM sera charg de rvaluer le produit final (y compris l'metteur) et l'obtention d'une autorisation IC spare. End Product Labelling This transmitter module is authorized only for use in device where the antenna may be installed such that 20cm may be maintained between the antenna and users. The final end product must be labelled in a visible area with the following:
Contains IC: 10462A-WG140000"
Ce module metteur est autoris uniquement pour une utilisation dans le dispositif o l'antenne peut tre install de telle sorte que 20cm peut tre maintenue entre l'antenne et les utilisateurs. Le Page 21 Copyright JORJIN TECHNOLOGIES INC. 2015 http://WWW.JORJIN.COM.TW CONFIDENTIAL Doc No: WG1400-00-DTS-D05 produit final doit tre tiquet dans un endroit visible par le texte suivant:
"Contient IC: 10462A-WG140000"
Manual Information to the End User The OEM integrator has to be aware not to provide information to the end user regarding how to install or remove this RF module in the users manual of the end product which integrates this module. L'intgrateur OEM doit tre conscient de ne pas fournir des informations l'utilisateur final sur la faon d'installer ou de supprimer ce module RF dans le manuel de l'utilisateur du produit final qui intgre ce module. Page 22 Copyright JORJIN TECHNOLOGIES INC. 2015 http://WWW.JORJIN.COM.TW CONFIDENTIAL