FCC ID: 2AWSB-MGENET MG Flasher Enet Wifi

MHD OBD2 Flasher Wifi Enet Module User Manual Overview MHD OBD2 Wifi Flasher was specially developed and designed to operate the Ethernet OBD2 diagnostic and coding features via wired J2534 port and wireless via an embedded module based on the universal serial interface network standard,built-in TCP / IP protocol stack, enabling the user serial port, Ethernet, interface wireless between the traditional serial devices do not demand to change any configuration, data can be transmitted Internet conversions. network through

(wifi) the the network. Provide a quick solution for the users serial devices to transfer data via Ethernet Features 2.4GHz 802.11b/g/n,compatible Support IEEE 802.3IEEE 802.3u WiFi Client/AP/Router Mode Support wps/wds The range of baudrate: 1200~500000bps Support transparent transmission mode Support multiple security authenti-cation mechanisms:

WEP64/WEP128/ TKIP/ AES WEP/WPA-PSK/WPA2-PSK Support wireless roam Support multiple network protocols:

PPPOE/TCP/UDP/DDDNS /DHCP/DNS/HTTP/Firewre Support AT+ instruction set Support two config methods:Serial/WEB Device Dimensions 87*47*26mm 1 MHD OBD2 Flasher Wifi Enet Module User Manual Applications Ethernet OBDII WiFi Diagnose Specifications The parameters are defined here. 2 MHD OBD2 Flasher Wifi Enet Module User Manual Wi-Fi Module Pin Assignment Electrical Characteristics 3 MHD OBD2 Flasher Wifi Enet Module User Manual Operation Guidelines to work with car OBDII Step 1: Ignition ON, plug the MHD OBDII wifi flasher to the OBD2 diagnostic port Step 2: Search the Wifi ISID started with MHD_XXXX from laptop wifi and access with the password which sated at the back side of the module. Step 3: Successfully connected and operated as user demanded via OBD2 diagnostic port. Step 4: Administration panel setup for administrators only. 4 MHD OBD2 Flasher Wifi Enet Module User Manual Appendix Disclaimers The contents of this document are subject to change without notice. Autosvs Technology reserves the right to make changes, without notice, in the products, including circuits and/or software, described or contained therein. Information contained in this document regarding device applications and the like is intended through suggestion only and may be superseded by updates. It is your responsibility to ensure that your application meets with your specifications. Autosvs Technology warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with Autosvs Technologys standard warranty. Testing and other quality control techniques are used to the extent Autosvs Technology deems necessary to support this warranty. Except where mandatory by government requirements, testing of all parameters of each product is not necessarily performed. Autosvs Technology assumes no responsibility or liability for the use of any of these products, conveys no license or title under any patent, copyright, or mask work right to these products, and makes no representations or warranties that these products are free from patent, copyright, or mask work infringement, unless otherwise specified. Autosvs Technology products are not intended for use in life support systems, appliances or systems where malfunction of these products can reasonably be expected to result in personal injury, death or severe property or environmental damage. Autosvs Technology customers using or selling these products for use in such applications do so at their own risk and agree to fully indemnify Autosvs Technology for any damages resulting from such use. All products are sold subject to Autosvs Technology 's terms and conditions of sale supplied at the time of order acknowledgment. All trademarks are the property of their respective owners. NB Warning:

Manufacturer's Name: JR Auto Performance Inc. Sample Description: MG Flasher Enet Wifi Trade Mark: /

Model number: MG Flasher Enet Wifi Operating Temperature: -10 C to 40 C Wireless specification:

2.4G WIFI: Max power 14.38dbm in frequency band 2412-2462MHz This product is a fixed location. To comply with RF exposure requirements, a minimum separation distance of 20cm must be maintained between the users body and the device, including the antenna. The device complies with RF specifications when the device used at 20cm from your body. Use only the supplied or an approved antenna. This device in compliance with the essential requirements and other relevant provisions of Directive 2014/53/EU. All essential radio test suites have been carried out. 5 MHD OBD2 Flasher Wifi Enet Module User Manual FCC Warning:

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

-- Reorient or relocate the receiving antenna.

-- Increase the separation between the equipment and receiver.

-- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

-- Consult the dealer or an experienced radio/TV technician for help. To maintain compliance with FCCs RF Exposure guidelines, This equipment should be installed and operated with minimum distance between 20cm the radiator your body: Use only the supplied antenna. FCC ID: 2AWSB-MGENET 6

C5266091_X10_Ed.2

< JR Auto Performance Inc. >

Office of Engineering Technology Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 Date: 7/9/20 Subject: Request for Confidentiality FCC ID: 2AWSB-MGENET To Whom It May Concern, Pursuant to the provisions of Sections 0.457 and 0.459 of Commission's rules

(47CFR0.457, 0.459), we are requesting the Commission to withhold the following attachment(s) as confidential document from public disclosure. Long-Term Confidentiality Short-Term Confidentiality NOTE 2 Exhibits ID Label/Location Attestation Statement External Photos Block Diagram Schematics Test Report Test Setup Photos Users Manual Internal Photos Parts List / Tune Up RF Exposure Info Operational Description Cover Letter(s) SDR Software / Security Info No No No No No No No NOTE 1 NOTE 1 No No No No No No NOTE1:LongTermConfidentialitymaybepermittedunderspecialconditions(SeeII.LONGTERMCONFIDENTIALITY,Section3of KDB726920,uselastinforce) NOTE2:ShortTermConfidentialitycanberequestedforamaximumof180daysfromthedateofthegrant. Above mentioned document contains detailed system and equipment description are considered as proprietary information in operation of the equipment. The public disclosure of above documents might be harmful to our company and would give competitor an unfair advantage in the market. In case of short-term Confidentiality, the applicant requests the exhibits selected above are withheld from public view for a period of ______ days from the date of the Grant of Equipment Authorization and prior to marketing. It is our understanding that all measurement test reports, FCC ID label format and correspondent during certification review process cannot be granted as confidential documents and those information will be available for public review once the grant of equipment authorization is issued. 1/1 C5266091_X10_Ed.2 Sincerely, Signature:

Name: Jaroslaw Paradny Title: Manager 1/1

C5266091_X8_Ed.1 Letter of Authorization

< JR Auto Performance Inc.>

JR Auto Performance Inc. 1428 Speers Rd Unit#3 Oakville, Ontario L6L 5M1 Company:

Address:

Canada Product Name: MG Flasher Enet Wifi Model Number: MG Flasher Enet Wifi FCC Identifier: 2AWSB-MGENET We authorize LGAI Technological Center S.A., Ronda de la Font del Carme, s/n, 08193 Bellaterra, Spain, to act on our behalf on all matters concerning the above named equipment. Any individual within LGAI Technological Center S.A. is authorized to act on our behalf and take action on the application. We declare that authorize LGAI Technological Center S.A., Ronda de la Font del Carme, s/n, 08193 Bellaterra, Spain, is allowed to forward all information related to the approval project to the Federal Communication Commission and to discuss any issues concerning the approval application. Any and all acts carried out by LGAI Technological Center S.A. on our behalf shall have the same effect as acts of our own. Name:

Title:

Signature of applicant:

Jaroslaw Paradny Date: 2020-07-09 Manager 1/1