Installation guide Congratulations - you have just purchased a SiriusWeb solution. Once installed, SiriusWeb will allow you to monitor your storage or living areas and consult the measurements from any PC connected to the Internet. G 9 6 8 8 0
:
f r Function diagram Provided material Unpack carefully your parcel and check that you have all the below mentioned items. Then proceed with the installation of the SPY RF and your SiriusBox as described below. 1- The SPY RF recorders Ambient probe model SPY RF T+, Green, Air and TH Remote probe model SPY RF U, N and C 2- The SiriusBox includes a wall mounting bracket and a power supply cord. 3- One wall mounting bracket for each SPY RF recorder
(only supplied with remote probe SPY RF recorders). 4- Double-sided adhesive tape for each SPY RF recorder
(only supplied with remote probe SPY RF recorders). JRI 1 Your step installation guide 12 1 Connect your probes Note: Go straight to Step 2 if you have an orange SPY RF T+, Mini SPY Green or SPY RF TH -type recorder. Connect the probes to the SPY RF only if you have a model with a remote probe (refer to the user manual of the SPY RF recorders). 2 Install your SPY RF recorders Note: JRI advises you to consult your certified SPY RF installer in order to carry out the installation of the recorders properly. Ambient recorders (SPY RF T+, TH, Green, Air) the in an upright position
>
Place the compartment/chamber/area you want to monitor, about two thirds up. recorder(s) inside or Remote recorders (SPY RF U, N or C)
>
Place the recorder(s) outside the compartment/chamber/area in an upright position as high up as possible on the exterior partition (of the compartment/chamber). A wall mounting bracket and double-
sided adhesive tape are provided for this purpose. The probe connected to the recorder must be placed in the centre inside the compartment/chamber/area in order to register a tempe-
rature as uniform as possible. Put the flat cable of the probe through the door seal at the level of the hinges of your compartment/chamber. JRI 2 3 Install your SiriusBox Choose an appropriate place on the wall close to a socket. It is important that you are in a GSM coverage area. The SiriusBox must be placed at a reasonable distance from the SPY RF recorders
(max. 50 m). Fix the wall mounting bracket to the wall in an upright position (at a height of 2 m minimum and 50 cm from the ceiling).The release lever should turn upwards. Depending on the surface of the wall, use two screws or double-sided adhesive tape or Velcro. Fasten the SiriusBox on the wall mounting bracket by sliding it upwards, then downwards until you hear a click.
(note: to unfasten the SiriusBox, push gently on the release lever, push the box upwards and then downwards). 4 Connect your SiriusBox Plug the adapter into the socket. At the bottom of the box, the first green LED lights up indicating that the SiriusBox is powered. JRI 3 The second green LED lights up when the connection to the GSM network is established. It turns on 10-30 seconds after being connected. If it does not, this means that there is an insufficient GSM coverage. In this case, move the device and try again. The yellow LED indicates that data exchanges between the SiriusBox and the SPY RF recorders are taking place. The red LED indicates that an alert is on. 5 Start your recorders If the temperature is not displayed on the SPY RF recorder(s), press the push-button for at least 5 seconds to set it going (refer to the user manual of the recorders...). Your system is now working. JRI 4 6 Log on to the SiriusWeb to Log on and password. Click "CUSTOMER ACCESS" in the upper right corner. A window appears. Enter your login and password, then click "OK . the www.jri-maxant.com website using login your 7 Display General consultation of all your monitored units (M.U.) straight from the home page. Last measurement transferred to SiriusWeb platform State of alarm colour Graph display of the last 24 hours Digital display of the last 24 hours Note : Generally, the locally recorded data is transferred to the SiriusWeb platform every 3 hours to be displayed. JRI 5 8 Manage your profiles (Site manager only) When you click PROFILE , you can set different logins and passwords to access the SiriusWeb website and then manage multiple profiles: user, administrator... 9 Activate your threshold alarms and your time delays
(Site manager only) Click on the button to open the monitored unit parameters. Enter the name of your monitored unit and activate the alarm of your recorder. Set also your alarm thresholds and time delays. Once these fields are filled in, click on "FINISH INSTALLATION". CONTINUE If you have more INSTALLATION. After having registered/entered all your devices, click on FINISH INSTALLATION. than one monitored unit to configure, click on Enter the name of your monitored unit Activate the alarm Set your alarm thresolds and time delays Note : JRI advises to have data for each monitored unit for at least a couple of days in order to determine the threshold values and the time delays. JRI 6 10 Activate your alarms (Site manager only) JRI advises to set several different types of alarms. Click on the ALARM MANAGENENT icon A- Remote alerts Configure your alert types (SMS text message, email, phone call) and your remote alarms. The remote alarms planning is used to activate the monitored units alerts during a specific period of time. Once the type of alerts is selected, click on ADD. SMS / Text message Phone call Email 2 phone numbers can be configured 2 phone numbers can be configured Unlimited email addresses One single SMS text message is sent 3 attempts every 15 minutes Every email is sent once Acknowledgment is possible Acknowledgment is possible No acknowledgment Alarm types Remote alarms schedule JRI 7 In case of alert, click on ALARM LIST and indicate the reason of the alarm. Current alarm B- Local alerts If you want to be locally alerted, click on SiriusBox parameters and activate the buzzer of your SiriusBox which beeps in case of alarm. In case of alarm, acknowledgment of the buzzer is achieved in the same way as for remote alarms. Buzzer activation You can shut down the buzzer by pressing on push button However, it is necessary to give the reason of the alarm on the SiriusWeb interface. If necessary (persistent default or problem to connect to SiriusWeb), it is possible to reset the SiriusBox by inserting a metal rod (paperclip) into the hole provided for this purpose (RESET). JRI 8 Note : It is possible to install an additional alarm system allowing to send alarms even if the GPRS signal is down (voice dialer, sound and visual alarm device, transmission to a telemonitoring com-
pany ...). Connection with an additional alarm system Relay output :
Common NC (normally closed) No (normally opened) 11 Review the Audit trail While clicking on , you can review the complete list of operated actions on your installation. You can sort the information per type of events. Filters 12 Configure a weekly report by email You can receive a weekly report (every Tuesday) presenting a sum up of your data. To configure it, access your profile by clicking on the icon In Preferences select the case Activate the remote reading and type the email address of the addresse(s) of the report. JRI 9 Advice to check that your installation is working Before going through the checking steps, please wait for 8 hours while the system is turned on. Unplug the Sirius Box. You should receive an alert depending on the pre-programmed alerts. If you dont receive any alert, follow the steps:
1/ Check your alerts programming (Buzzer and/or text message, email, voice message) on Sirius-
Web. 2/ Check the connection of the power supply of the SiriusBox. 3/ Check the GPRS communication level. Click on SIRIUSBOX PARAMETERS to access the information on the SiriusBox. The minimum level of communication is 2 grades. 4/ Check the connection of the backup battery. Connector Backup battery Open the Sirius Box with the help of a pen placing it inside both holes on the upper and down sides of the SiriusBox. Check that the connector of the backup battery is connected to the electronic board. Your installation should now be working. However if you still dont have any communication, please contact our technical support. JRI 10 Advice to check measurement upload 1/ Check that temperature is displayed on the LCD screen or that the leds are blinking. 2/ Check that the measurements of your monitored units displayed on SiriusWeb are less than 8 hours. In case of failure If the lights are off, check the power of the SiriusBox by checking the plug. If the SiriusBox does not work, perform a soft reset by inserting a metal rod (such as a paper clip) into the hole provided for this purpose (RESET). If there are no longer measurements on SiriusWeb, check that the recorders are on. If they are off, press at least 5 sec their push button to turn them on. If they still do not start, replace the battery and turn on the recorders. Icons glossary Refresh measurements of all monitored units linked to the SiriusBox Display measurements Add a comment list Adapt the display of the curve according to the selected interval JRI Print the page 11 Key features Radio features Emission band Maximum radiated power Range with SpyRF satellites in buildings ISM 868 MHz 10 dBm (10 mW) Up to 50 meters depending on the environment Emission band Maximum radiated power Power supply Power consumption Backup battery Backup battery lifetime GPRS features GSM 900 MHz or DCS 1800 MHz
(depending on the operator of the mobile subscription) 2W in GSM mode 1W in DCS mode Electrical features Adapter plug (European model) with regulated output voltage :
input: 230 V CA output: 9 V CC - 650 mA cord fixed: 1,80 m Average consumption : 0,5 W Peak consumption : 5 W NiMH capacity 650mAh Fully operational autonomy : 12h rs Loading time : 100hrs Mechanical and environmental features Dimensions Weight Protection index Conditions of use Pollution / altitude (IEC 61010-1) 154x84x37 mm 270g (without adapter) IP20 - to be used indoors only 0C to 50C - 0 to 90% RH Degree of pollution : 2 Operating altitude: 0 to 2000m Installation Precautions SiriusBox hub must be fixed in a vertical position (such as that SpyRF satellites). A wall mounting bracket is provided. This support can be fixed to the wall with two screws, or with a double-sided adhesive (also provided). The SiriusBox should not be fixed on a metal surface and in a place with insufficient GSM network coverage. A socket should be available nearby (within a maximum of 3m) to allow plugging in the AC adapter. It serves as the disconnecting device. WARNING This unit contains a rechargeable NiMH battery. Never attempt to disassemble, to charge and to short circuit. Always use the battery correctly, do not expose to temperatures above 100 C, do not wet and respect the polarities. Keep the battery out of templates provided by JRI. They have a undeceived connector to prevent polarity reversal. JRI disclaims all liability for use of a different battery. In case of non-compliance with these instructions, alcalins hydroxides may leak from the valve safety. reach of children. Always the battery with replace the the JRI 12 Symbols RECYCLING: Do not dispose in a landfill or in a container collection waste. Comply with the legislation for the disposal. ELECTRICAL POWER: This unit is DC powered from a 230 V AC adapter. Comply with the safety rules in the use of electric power. Use an electrical installation complies with the legislation. CE MARKING: This device flamability, radiation emission disturbing and immunity to electrical interference nearby. the European is certified regulations to for electrical safety, ELECTRICAL INSULATION: This device is protected by a double electrical insulation or electrical insulation rein-
forced. Maintenance No maintenance is necessary. For cleaning, do not use water but a dry cloth. Safety / Certifications CE radio compliant : EN 301 489 / EN 300 220 / EN 61010 / EN 301 511 Warranty JRI products carry a one year warranty and guarantee against defects in their components or workmanship. During this period if any product supplied by the Company proves on inspection to be defective, the Company will at its own option replace the same or refund to the Buyer the price of the product. In no circumstances will JRI' liability exceed the price of the product paid by the buyer or the cost of replacement. JRI shall not in any event be liable to the Buyer for any indirect or consequential loss or damage costs or expenses what-
soever which might arise out of or in connection with the supply of the product or its consequent use. Consequently, the products warrantee and guarantee specified above, does not cover damage caused by fair wear and tear, abnormal storage conditions, incorrect use, accidental misuse, abuse, neglect, misapplication or modification, or use with non-JRI' hardware/software. No warranty of fitness for a particular purpose is offered and the user assumes the entire risk of using the product. In line with our policy of continuous development, we reserve the right to amend our product specification without prior notice. Recycling If it must be discarded, this equipment must be in compliance with the legislation on electronic equipment. It should never be disposed in the landfill or never be treated by the services of the road. For more information, call the JRI cus-
tomer service. Important note FCC ID Box=W4510620-03 FCC ID GPRS=N7NWISMO228 FREQUENCY This device is designed to operate in the band [902.22 904.149] MHz. FCC COMPLIANCE STATEMENT This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: This device may not cause harmful interference, and must accept any interference received, including interference that may cause undesired operation. INFORMATION TO THE USER The users manual or instruction manual for an intentional or unintentional radiator shall caution the user that changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to ope-
rate the equipment. FCC RADIATION EXPOSURE STATEMENT The antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons. JRI 13 Minimal configuration Internet Browser :
Internet Explorer 7 +, FireFox 1.0 + and Chrome 1.0 + and Safari 2.0 +. Screen resolution: 1280px * 680px at least Javascript must be enabled. SiriusWeb iPhone App You can now have SiriusWeb on your the App and enter your login and password. iPhone. Go on AppStore, download The iPhone SiriusWeb App offers the following functions:
- Display all your monitored units : temperature values, thresholds, measurement graph
- Management of alarms and history
- Send email to our technical support It is also available in German, Spanish, Italian, Portuguese and Dutch. JRI 14 Technical assistance Our technical support is at your disposal on
+33 3 63 15 80 07 Indicate your SiriusWeb login click in the upper right corner of the siriusweb.fr site in order to forward us your question. or click In the upper right corner of the SiriusWeb.fr website to access the FAQ