all | frequencies |
|
exhibits | applications |
---|---|---|---|---|
manual |
app s | submitted / available | |||||||
---|---|---|---|---|---|---|---|---|
1 2 3 4 5 6 |
|
USERS MANUAL | Users Manual | 911.47 KiB | ||||
1 2 3 4 5 6 | Cover Letter(s) | August 03 2007 | ||||||
1 2 3 4 5 6 | Cover Letter(s) | August 03 2007 | ||||||
1 2 3 4 5 6 | Cover Letter(s) | |||||||
1 2 3 4 5 6 | Internal Photos | |||||||
1 2 3 4 5 6 | Test Setup Photos | |||||||
1 2 3 4 5 6 | Test Report | |||||||
1 2 3 4 5 6 | Cover Letter(s) | |||||||
1 2 3 4 5 6 | Cover Letter(s) | |||||||
1 2 3 4 5 6 | External Photos | August 04 2005 | ||||||
1 2 3 4 5 6 | ID Label/Location Info | |||||||
1 2 3 4 5 6 | Internal Photos | August 04 2005 | ||||||
1 2 3 4 5 6 | Test Report | |||||||
1 2 3 4 5 6 | Test Report | |||||||
1 2 3 4 5 6 | Test Setup Photos | |||||||
1 2 3 4 5 6 | RF Exposure Info | June 04 2005 |
1 2 3 4 5 6 | USERS MANUAL | Users Manual | 911.47 KiB |
Trapeze Mobility Point MP-372 Installation Guide Part Number 730-9502-0052, Revision C Trapeze Networks, Inc. 5753 W. Las Positas Blvd. Pleasanton, CA 94588 Tel: +1 925-474-2200 Fax: +1 925-251-0642 Toll-Free: 877-FLY-TRPZ (877-359-8779) www.trapezenetworks.com 2005 Trapeze Networks, Inc. All rights reserved. Trademarks Trapeze Networks, the Trapeze Networks logo, the Trapeze Networks flyer icon, Mobility System, Mobility Exchange, MX, Mobility Point, MP, Mobility System Software, MSS, RingMaster, AAA Integration and RADIUS Scaling, ActiveScan, AIRS, Bonded Auth, FastRoaming, Granular Transmit Power Setting, GTPS, GuestPass, Layer 3 Path Preservation, Location Policy Rule, LPR, Mobility Domain, Mobility Profile, Passport-Free Roaming, SentryScan, Time-of-Day Access, TDA, TAPA, Trapeze Access Point Access Protocol, Virtual Private Group, VPG, Virtual Service Set, Virtual Site Survey and WebAAA are trademarks of Trapeze Networks, Inc. Trapeze Networks SafetyNet is a service mark of Trapeze Networks, Inc. All other products and services are trademarks, registered trademarks, service marks or registered service marks of their respective owners. Disclaimer All statements, specifications, recommendations, and technical information are current or planned as of the date of the publication of this document. They are reliable as of the time of this writing and are presented without warranty of any kind, expressed or implied. In an effort to continuously improve the product and add features, Trapeze Networks reserves the right to change any specifications contained in this document without prior notice of any kind. Comments and Feedback Your feedback on Trapeze documentation is important to us. Send any comments and suggestions to doc-bugs@trapezenetworks.com. For the most current version of this document, see www.trapezenetworks.com. Note. The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment. Such modifications could void the users authority to operate the equipment. ii Customer Service For general information about Trapeze Networks Mobility System products and services, visit www.trapezenetworks.com. For warranty, license, and support information, visit the following sites:
Warranty and software licenses. Current Trapeze Networks warranty and software licenses are available at www.trapezenetworks.com/services/
warranty.asp. Support services. For information about Trapeze support services, visit www.trapezenetworks.com/services/. Or call 1-866-877-9822 (in the US or Canada) or +1 925-474-2400 and select option 5. Note. TRAPEZE NETWORKS SELLS AND SERVICES ITS PRODUCTS PRIMARILY THROUGH ITS AUTHORIZED RESELLERS AND DISTRIBUTORS. If you purchased your product from an authorized Trapeze reseller or distributor and do not have a service contract with Trapeze Networks, you must contact your local reseller or distributor for technical assistance. Contacting the Technical Assistance Center Contact the Trapeze Networks Technical Assistance Center (TAC) by telephone, email, or fax. If you have a service contract or are a Trapeze Authorized Partner, log in to www.trapezenetworks.com/services/sup_programs.asp for more help. Within the US and Canada, call 1-866-TRPZTAC (1-866-877-9822). Within Europe, call +31 35 64 78 193. From locations outside the US and Canada, call +1 925-474-2400. In non-emergencies, send email to support@trapezenetworks.com. When your case is active, you can fax more information to +1 925-474-2423. iii TAC Response Time TAC responds to service requests as follows:
Contact method Telephone Email Response time One hour Priority Emergency Non-emergency Next business day Non-emergency Next business day Information to Have Available To expedite your service request, have the following information available when you call or write to TAC for technical assistance:
Your company name and address Your name, telephone number, cell phone or pager number, and email address Name, model, and serial number of the product(s) requiring service Software version and release number Output of the show tech-support command Wireless client information License levels for RingMaster and Mobility Exchange (MX) products Description of the problem and status of the troubleshooting effort iv Trapeze Mobility Point Installation Guide Contents Customer Service. iii 1 Introducing the Trapeze Networks Mobility System . 1 Trapeze Networks Mobility System . 1 Documentation . 2 Safety and Advisory Notices . 4 Text and Syntax Conventions . 5 2 MP Overview . 7 External Hardware Features . 8 Cable Ports . 9 External Antenna Connectors . 10 Kensington Security Slot . 12 MP Mounting Options . 12 Status LEDs . 12 Connection Options . 14 3 Installing and Connecting an MP-372 . 15 Unpacking an MP . 16 Installation Requirements and Recommendations . 18 RingMaster Network Plan and Work Orders . 18 MX Switch Recommendation . 18 Wall Installation Recommendations . 19 MP Radio Safety Advisories . 19 Radio Frequency Exposure . 19 Additional Radio Safety Advisories . 19 Cable Requirements . 20 Installing an MP-372 . 22 Installation Hardware and Tools . 22 Suspended Ceiling InstallationFlush Ceiling Tiles . 24 Suspended Ceiling InstallationDrop Ceiling Tiles . 30 Contents v Junction Box Installation . 36 Solid Wall or Ceiling Installation . 40 Tabletop Installation . 45 Connecting an MP to an External Antenna . 49 Connecting an MP to an MX Switch . 50 Verifying MP Health . 52 A MP Troubleshooting. 53 B MP Technical Specifications . 55 C Translated Warning Conventions and Warnings . 61 Index. 69 vi Trapeze Mobility Point Installation Guide 1 Introducing the Trapeze Networks Mobility System Trapeze Networks Mobility System . 1 Documentation . 2 This guide shows you how to install a Trapeze Networks Mobility Point
(MP) access point in a Trapeze Networks Mobility System wireless LAN
(WLAN). Read this guide if you are a network administrator or other person installing MP access points in a network. Trapeze Networks Mobility System The Trapeze Networks Mobility System is an enterprise-class WLAN solution that seamlessly integrates with an existing wired enterprise network. The Trapeze system provides secure connectivity to both wireless and wired users in large environments such as office buildings, hospitals, and university campuses. The Trapeze Mobility System fulfills the three fundamental requirements of an enterprise WLAN: It eliminates the distinction between wired and wireless networks, allows users to work safely from anywhere (secure mobility), and provides a comprehensive suite of intuitive tools for planning and managing the network before and after deployment, greatly easing the operational burden on IT resources. Introducing the Trapeze Networks Mobility System 1 Documentation Chapter 1 The Trapeze Networks Mobility System consists of the following components:
RingMaster tool suiteA full-featured graphical user interface (GUI) client application used to plan, configure, and deploy a WLAN and its users. It also provides a centralized service application for WLAN and user monitoring, reporting, and diagnostics One or more Mobility Exchange (MX) switchesDistributed, intelligent machines for managing user connectivity, connecting and powering Mobility Point (MP) access points, and connecting the WLAN to the wired network backbone Multiple Mobility Point (MP) access pointsWireless access points
(APs) that transmit and receive radio frequency (RF) signals to and from wireless users and connect them to an MX switch Mobility System Software (MSS)The operating system that runs all MX switches and MP access points in a WLAN, and is accessible through a command-line interface (CLI), the Web View interface, or the RingMaster GUI Documentation Consult the following documents to plan, install, configure, and manage a Trapeze Networks Mobility System. Planning, Configuration, and Deployment Trapeze RingMaster Users Guide. Instructions for planning, configuring, deploying, and managing the entire WLAN with the RingMaster tool suite. Read this guide to learn how to plan wireless services, how to configure and deploy Trapeze equipment to provide those services, and how to optimize and manage your WLAN. Trapeze RingMaster Reference Manual. Detailed instructions and information for all RingMaster planning, configuration, and management features. 2 Trapeze Mobility Point Installation Guide Documentation Chapter 1 Installation Trapeze Mobility System Software Quick Start Guide. Instructions for performing basic setup of secure (802.1X) and guest (Web AAA) access, for configuring a Mobility Domain for roaming, and for accessing a sample network plan in RingMaster for advanced configuration and management Trapeze Mobility Exchange Installation and Basic Configuration Guide. Instructions and specifications for installing an MX switch in a Trapeze Mobility System WLAN, and basic instructions for deploying a secure IEEE 802.11 wireless service Trapeze Mobility Point Installation Guide. Instructions and specifications for installing an MP access point and connecting it to an MX switch Trapeze Regulatory Information. Important safety instructions and compliance information that you must read before installing Trapeze Networks products Configuration and Management Trapeze RingMaster Reference Manual. Instructions for planning, configuring, deploying, and managing the entire WLAN with the RingMaster tool suite Trapeze Mobility System Software Configuration Guide. Instructions for configuring and managing the system through the MSS CLI Trapeze Mobility System Software Command Reference. Functional and alphabetic reference to all MSS commands supported on MX switches and MP access points Introducing the Trapeze Networks Mobility System 3 Documentation Chapter 1 Safety and Advisory Notices The following kinds of safety and advisory notices appear in this manual. (For translations of the warning conventions and of all warnings in this manual, see Appendix C, Translated Warning Conventions and Warnings, on page 61.) Caution! This situation or condition can lead to data loss or damage to the product or other property. Warning! This situation or condition can cause injury. Warning! High voltage. This situation or condition can cause injury due to electric shock. Warning! Radiation. This situation or condition can cause injury due to improper handling of fiber-optic equipment. Note. This information is of special interest. 4 Trapeze Mobility Point Installation Guide Documentation Chapter 1 Text and Syntax Conventions Trapeze manuals use the following text and syntax conventions:
Convention Monospace text Bold text Italic text Use Sets off command syntax or sample commands and system responses. Highlights commands that you enter or items you select. Designates command variables that you replace with appropriate values, or highlights publication titles or words requiring special emphasis. Menu Name > Command Indicates a menu item that you select. For example, File > New indicates that you select New from the File menu. Enclose optional parameters in command syntax. Enclose mandatory parameters in command syntax. Separates mutually exclusive options in command syntax.
[ ] (square brackets)
{ } (curly brackets)
| (vertical bar) Introducing the Trapeze Networks Mobility System 5 Documentation Chapter 1 6 Trapeze Mobility Point Installation Guide 2 MP Overview External Hardware Features . 8 Connection Options . 14 A Trapeze Networks Mobility Point (MP) access point provides IEEE 802.11 wireless access to the network. MP access points are designed for use with a Trapeze Networks Mobility Exchange (MX) switch. MP access points require hardware installation only. All configuration for an MP access point takes place on the MX switch. This guide describes MP model MP-372. The MP-372 has one 802.11a radio and one 802.11b/g radio. Both radios have internal diversity omnidirectional antennas. In addition, both radios have separate jacks for attachment of optional external sectorized or directional antennas. The antennas must be ordered separately. Warning! Installation must be performed by qualified service personnel only. Read and follow all warning notices and instructions marked on the product or included in the documentation. Before installing the product, read the Trapeze Regulatory Information document. (For translations of this warning, see Qualified Service Personnel Warning on page 63.) Note. The MP radios are disabled by default and can be enabled only by a system administrator using the MX switch. MP Overview 7 External Hardware Features Chapter 2 External Hardware Features Figure 1 and Figure 2 show the external hardware features of the MP-372. Figure 1. MP Access Point Model MP-372Top View Diameter 16.76 cm
(6.6 inches) Height 4.69 cm
(1.85 inches) 0 4 0 0
2 0 5 9
0 4 8 Figure 2. MP Access Point Model MP-372Bottom View Kensington security slot External antenna connectors 802.11a 802.11b/g k c nlo U 7 0 0 0
2 0 5 9
0 4 8 RJ-45 ports Port 2 Port 1 8 Trapeze Mobility Point Installation Guide External Hardware Features Chapter 2 Cable Ports The MP-372 has two RJ-45 ports. (See Figure 2.) Each port provides a 10/100BASE-TX Ethernet connection to an MX switch. The connection can be direct to an MX-switch or indirect through an intermediate Layer 2 or Layer 3 network. The MP receives power and data through the RJ-45 ports. Use a Category 5
(Cat 5) cable with straight-through signaling and standard RJ-45 connectors to connect an MP to an MX switch or other device in the network. The MP-372 supports 802.3af, and also can receive PoE from Trapeze switches and Trapeze-approved power injectors. (See the Release Notes for Trapeze Networks Mobility Point Access Points.) The two RJ-45 ports support dual-homed configurations for redundancy. An MP uses only one link for booting, configuration, and data transfer. If the link becomes unavailable, the MP can reboot using the other link. The ports are identical except for logical numbering (1 or 2). You can use either port to connect an MP access point to an MX switch. However, an MP always attempts to boot on MP port 1 first. Only if the boot attempt on port 1 fails does the MP attempt to boot on port 2. If one port becomes unavailable, the other port can provide full power to the MP. Note. MP access points do not support daisy-chain configurations. Do not connect the MP access point to another MP access point. MP Overview 9 External Hardware Features Chapter 2 External Antenna Connectors The MP-372 has connectors for attaching optional external antennas. (See Figure 2.) Table 1 lists the external antenna models. Table 1. Trapeze External Antenna Models Model Type Gain Beamwidth Horizontal Vertical 60 14 120 802.11a 802.11a 14.5 dBi 12.5 dBi ANT-5060
(ASTN6S)1 ANT-5120
(ASTN6T) ANT-5180
(ASTN6H) ANT-1060 ANT-1120 ANT-1180 1. The numbers in parentheses are the numbers that appear on the back of an 802.11a antennas reflector plate. 802.11b/g 802.11b/g 802.11b/g 10 dBi 7 dBi 6 dBi 60 120 180 65 60 40 10.8 dBi 802.11a 180 To verify an 802.11a external antennas model number, look for the number in parentheses. 14 14 Note. The MP-372 radios are certified for use only with these external antennas. Figure 3 shows the 802.11b/g antennas. 10 Trapeze Mobility Point Installation Guide Figure 3. External 802.11b/g Antennas External Hardware Features Chapter 2 Model ANT-1060 Model ANT-1180 Model ANT-1120 7 7 0 0
2 0 5 9
0 4 8 The 802.11a external antennas look similar to the 802.11b/g model ANT-1180, but each has a reflector plate specific to the model number. You can identify an 802.11a external antennas model by looking on the back of its reflector plate. Do not reverse or remove the reflector plate. It is required for antenna operation. Each antenna comes with a connector cable, mounting hardware, and installation instructions. Caution! The external connectors on the MP are labeled: 11B/G and 11A. Each connector is a standard SMA connector. Make sure you attach the antenna to the correct connector. Note. Operation in the band 5.155.25 Ghz is restricted to indoor use only. MP Overview 11 External Hardware Features Chapter 2 Kensington Security Slot Models MP-372 has a slot for attachment of a Kensington security cable. The cable is not included with the MP but can be ordered separately. MP Mounting Options You can mount an MP access point on any of the following types of surfaces:
Suspended T-bar ceiling Junction box Solid surface wall or ceiling Tabletop Note. The solid surface mounting option requires Cat 5 cable that does not have strain relief. The other mounting options can use Cat 5 cable with or without strain relief. Status LEDs The MP has LEDs that provide status information for the device. Figure 4 shows the locations of the LEDs. Table 2 describes the LEDs. Figure 4. Health and Radio LEDsMP-372 Radio 2 LED Radio 1 LED Health LED 0 1 0 0
2 0 5 9
0 4 8 12 Trapeze Mobility Point Installation Guide External Hardware Features Chapter 2 Table 2. MP Access Point LEDsMP-372 LED Health Appearance Solid green Radio 1 Radio 2 Solid amber Alternating green and amber Solid green Blinking green Blinking amber Alternating green and amber Unlit Meaning All the following are true:
Management link with an MX switch is operational. MP access point has booted. MP access point has received a valid configuration from an MX switch. At least one radio is enabled or is in sentry mode. MP access point is waiting to receive boot instructions and a configuration file from an MX switch. MP access point is booting and receiving its configuration file from an MX switch. A client is associated with the radio. Associated client is sending or receiving traffic. Non-associated client is sending or receiving traffic. Radio is unable to transmit. This state can occur due to any of the following:
Excessive radio interference in the environment is preventing the radio from sending beacons. The radio has failed. Means one of the following:
Radio is disabled. Radio is enabled, but no clients are associated with the radio and there is no traffic activity. MP Overview 13 Connection Options Chapter 2 Connection Options You can connect an MP access port directly to an MX switch port or indirectly to MX switches through an intermediate Layer 2 or Layer 3 network. In either case, use Category 5 (CAT 5) cable with straight-through signaling for each MP connection. You also can provide data link redundancy by connecting both of its ports directly to MX switch ports or indirectly to MX switches through the network. You can provide MX management redundancy even on a single MP Ethernet port by connecting the MP indirectly to multiple MX switches through an intermediate Layer 2 or Layer 3 network. Note. Install the Cat 5 cables for the MP access point at the installation site before installing the access point itself. During installation, you will insert the Cat 5 cable(s) into the MP port(s) before attaching the access point to the bracket. 14 Trapeze Mobility Point Installation Guide 3 Installing and Connecting an MP-372 Unpacking an MP . 16 Installation Requirements and Recommendations . 18 Installing an MP-372 . 22 Connecting an MP to an MX Switch . 50 Verifying MP Health . 52 Note. Before installing an MP access point, you might need to generate a network plan and an MP work order with RingMaster. (See RingMaster Network Plan and Work Orders on page 18.) Installing and Connecting an MP-372 15 Unpacking an MP Chapter 3 Unpacking an MP The shipping carton for an MP access point contains the following items:
One MP access point Mounting kit:
One universal mounting bracket (attached to the MP) One paper mounting template (used for marking cutting areas and screw holes) One two-piece 14.2-mm (9/16-inch) T-bar clamp One two-piece 15.9-mm (5/8-inch) T-bar clamp One two-piece 23.9-mm (15/16-inch) T-bar clamp Two #6 sheet metal screws and two drywall anchors Three adhesive rubber feet One documentation pack that includes quick mounting instructions and a registration card (not shown) 16 Trapeze Mobility Point Installation Guide Figure 5 shows the contents of the shipping carton for model MP-372. Figure 5. MP-372 Shipping Carton Contents Unpacking an MP Chapter 3 Mobility point Mounting template Rubber feet Universal mounting bracket 1 0 0 0
2 0 5 9
0 4 8 T-bar clamps Mounting hardware Before you begin installation:
1 Open the carton and carefully remove the contents, if you have not already done so. 2 Place the packing materials back in the carton and save the carton. 3 Verify that you received each item in the previous list. If any item is missing or damaged, contact Trapeze Networks. Installing and Connecting an MP-372 17 Installation Requirements and Recommendations Chapter 3 Installation Requirements and Recommendations For best results, follow these requirements and recommendations before installing an MP access point. RingMaster Network Plan and Work Orders If you are using RingMaster to plan your Trapeze Networks Mobility System installation, you might want to create and verify a network plan for the entire Trapeze network installation and generate an MP work order, before installing MP access points. A network plan and the MP work orders generated from it provide the following information about MP access point installation and configuration:
Number of MP access points required for adequate WLAN capacity in each coverage area Detailed installation location for each MP access point Settings for all MP access points in the WLAN
(For information about installing RingMaster, creating and verifying a network plan, and generating an MP work order, see the Trapeze RingMaster Users Guide and Trapeze RingMaster Reference Manual.) MX Switch Recommendation Trapeze Networks recommends that you install and configure the MX switch before installing an MP access point. If the switch is already installed and configured for the MP access point(s), you can immediately verify the cable connection(s) when you plug the cable(s) into the MP access point. Caution! MP model MP-372 is designed to receive power only from an 802.3af-compliant source, a Trapeze Networks Mobility Exchange (MX) switch, or a Trapeze-approved power injector. Connecting an MP access point to a Power over Ethernet (PoE) device that is not approved by Trapeze Networks can damage the equipment. 18 Trapeze Mobility Point Installation Guide Installation Requirements and Recommendations Chapter 3
(For information about connecting an MP access point to an MX switch port, see Connecting an MP to an MX Switch on page 50.) Wall Installation Recommendations If you plan to install an MP on a partial wall or other vertical surface, orient the top of the access point (the side with the LEDs) toward the intended coverage area. The radio antennas transmit through the top of the access point but not through the bottom (where the bracket is). This recommendation does not apply if you plan to use external antennas. You can orient the antennas independently of the MP itself. Orient an external antenna to face the intended coverage area. MP Radio Safety Advisories When you enable the MP radio(s) as part of MX switch configuration, the radios are able to receive and transmit radio frequency energy as soon as you connect the MP access point(s) to the MX switch, either directly or through the network. Radio Frequency Exposure Federal Communications Commission (FCC) Docket 96-8 for Spread Spectrum Transmitters specifies a safety standard for human exposure to radio frequency electromagnetic energy emitted by FCC-certified equipment. When used with the proper antennas (shipped in the product), Trapeze Networks MP access point products meet the uncontrolled environmental limits found in OET-65 and ANSI C95.1-1991. Proper installation of the MP access point according to the instructions in this manual will result in user exposure that is below the FCC recommended limits. Additional Radio Safety Advisories
(For translations of warnings, see Radio Safety Warnings on page 64.) Warning! In the U.S., locate the MP access point and any externally attached antennas a minimum of 20 cm (7.9 inches) away from people. This safety warning conforms with FCC radio frequency exposure limits for dipole antennas such as those used in the MP access point. Installing and Connecting an MP-372 19 Installation Requirements and Recommendations Chapter 3 Warning! Do not operate the MP access point near unshielded blasting caps or in an otherwise explosive environment unless the device has been modified for such use by qualified personnel. Warning! Do not touch or move the MP access point when the antennas are transmitting or receiving. Warning! Do not hold any radio device so that the antenna is very close to or touching the face, eyes, or other exposed body part while the device's radio antenna is transmitting. Warning! Before using a wireless device in a hazardous location, consult the local codes, national codes, and safety directors of the location for usage constraints. Cable Requirements Warning! Do not connect or disconnect cables or otherwise work with the MP access point hardware during periods of lightning activity. (For translations of this warning, see Lightning Warning on page 67.) Note. The MP access point is intended for indoor use only. Do not install the device outdoors, unless you install it in a properly installed Trapeze Networks outdoor MP enclosure. Note. To reduce the possibility of connection interference caused by dust, clean the Cat 5 connector pins before inserting a cable into an MP access point. 20 Trapeze Mobility Point Installation Guide Installation Requirements and Recommendations Chapter 3 Cat 5 cable with straight-through signaling must be installed at the site before you install an MP access point. A single connection requires one cable. A dual-homed connection requires two cables. Table 3 lists the pin signals for 10/100 Ethernet straight-through wiring. Pins 4, 5, 7, and 8 are used when Trapeze Power over Ethernet (PoE) is enabled on the port. RD means Receive Data and TD means Transmit Data. Table 3. 10/100 Ethernet Straight-Through Pin Signals MX Switch Other Device Pin 1 2 3 4 5 6 7 8 Function RD+
RD-
TD+
PoE+
PoE+
TD-
PoE-
PoE-
Pin 1 2 3 4 5 6 7 8 Function TD+
TD-
RD+
PoE+
PoE+
RD-
PoE-
PoE-
Mounting an MP access point on a solid surface requires Cat 5 cable that does not have strain relief. For installation on all other surfaces, you can use Cat 5 cable with or without strain relief.
(For more information about cables, see Cable Ports on page 9.) Installing and Connecting an MP-372 21 Installing an MP-372 Chapter 3 Installing an MP-372 To install an MP-372, use one of the procedures in this section. Installation Hardware and Tools Table 4 lists the mounting hardware and tools required for each type of installation. Table 4. Required Mounting Hardware and ToolsModel MP-372 Mounting Option Required Hardware and Tools Suspended ceilingflush ceiling tiles Mounting template Universal mounting bracket T-bar clamp Included with the Product Yes Yes Yes Suspended ceilingdrop ceiling tiles Note: A T-bar clamp is not required for a 23.9-mm (15/16-inch) T-bar ceiling with flush ceiling tiles. Box cutter Small screwdriver (3-mm or 1/8-inch) Mounting template Universal mounting bracket T-bar clamp Box cutter Small screwdriver (3-mm or 1/8-inch) No No Yes Yes Yes No No 22 Trapeze Mobility Point Installation Guide Table 4. Required Mounting Hardware and ToolsModel MP-372 Installing an MP-372 Chapter 3 Mounting Option Junction box Solid wall or ceiling Tabletop Required Hardware and Tools Included with the Product No Junction box Two #6-32 x 1-inch machine screws Yes Yes Universal mounting bracket Small screwdriver (3-mm or No 1/8-inch)
#2 Phillips-head screwdriver Two #6 sheet metal screws and two drywall anchors Universal mounting bracket Hammer Small screwdriver (3-mm or 1/8-inch)
#2 Phillips-head screwdriver Universal mounting bracket Three adhesive rubber feet Small screwdriver (3-mm or 1/8-inch) No Yes Yes No Yes No No No Yes Note. The MP-372 model is UL2043 plenum rated, so it also can be installed in the space above the ceiling if preferred. Figure 6 shows the universal mounting bracket. Installing and Connecting an MP-372 23 Installing an MP-372 Chapter 3 Figure 6. Universal Mounting Bracket Port connector opening Screw holes T-bar flanges 8 1 0 0
2 0 5 9
0 4 8 Suspended Ceiling InstallationFlush Ceiling Tiles
(For required mounting hardware and tools, see Table 4 on page 22.) 1 Select an installation location that is centered over a T-bar in the ceiling. 2 Cut a hole as follows in the ceiling tile for the Cat 5 cable(s):
a Place the mounting template over the area where you plan to install the MP access point. b Use the box cutter to cut along the line marking the opening for the port connectors. c Remove the mounting template and the material you cut from the ceiling panel. 3 Determine whether to install a T-bar clamp onto the ceiling T-bar:
If the T-bar width is 14.2 mm (9/16 inches), you need to install the 14.2-mm (9/16-inch) T-bar clamp. Go to step 4. If the T-bar width is 23.9 mm (15/16 inches), the universal mounting bracket fits directly onto the T-bar. Go to step 5. 24 Trapeze Mobility Point Installation Guide Installing an MP-372 Chapter 3 4 Install the 14.2-mm (9/16-inch) T-bar clamp onto the ceiling T-bar as shown in Figure 7. a Slide each half of the clamp onto the T-bar so that the clamp lip is fully on the T-bar. b Slide the two halves of the clamp toward each other until the tabs are inserted completely into the holes and the clamp fits snugly on the T-bar. Figure 7. Step 4Installing a T-bar Clamp T-bar T-bar clamp halves Slide together 3 0 0 0
2 0 5 9
0 4 8 5 Unlock the universal mounting bracket from the MP access point by inserting the 3-mm or 1/8-inch screwdriver into the Unlock hole on the MP access point as shown in Figure 8. Caution! To avoid damage to the MP access points lock mechanism or electronic components, do not use excessive force when inserting a tool into the Unlock or Lock hole. Installing and Connecting an MP-372 25 Installing an MP-372 Chapter 3 Figure 8. Step 5Unlocking the Bracket 1 1 0 0
2 0 5 9
0 4 8 6 Remove the bracket as shown in Figure 9. Figure 9. Step 6Removing the Bracket 8 0 0 0
2 0 5 9
0 4 8 7 Install the universal mounting bracket as follows onto the T-bar or T-bar clamp:
a As shown in Figure 10, place the universal mounting bracket against the T-bar or clamp so that the two screw holes face downward and the two T-bar flanges face upward and are adjacent to the T-bar edges. 26 Trapeze Mobility Point Installation Guide Installing an MP-372 Chapter 3 Figure 10. Step 7Top View Universal mounting bracket T-bar Port connector opening
(Viewed from above ceiling tiles, looking down.) 5 0 0 0
2 0 5 9
0 4 8 b Properly align the bracket for mounting by placing the bracket so that its port connector opening is to the left of the hole you cut for the cables. c Rotate the universal mounting bracket clockwise until the flanges snap into place on the T-bar or clamp as shown in Figure 11. Figure 11. Step 7Bottom View Port connector opening Universal mounting bracket T-bar 4 0 0 0
2 0 5 9
0 4 8 8 Pull the Cat 5 cable(s) about 15 cm (about 6 inches) out of the hole in the ceiling tile and through the port connector opening to create enough slack to insert the cable(s). Installing and Connecting an MP-372 27 Installing an MP-372 Chapter 3 9 Insert the Cat 5 cable(s) into the connector(s):
For a single connection, use the connector for port 1. For redundancy, insert one cable into each connector. 10 Install the Kensington lock, if you plan to used one. a Loop the Kensington locks cable around an object that cannot be moved or damaged by a person pulling on the cable. b Insert the key into the Kensington lock. Insert the Kensington lock into the security slot on the MP. c d Rotate the key right or left to secure the lock to the MP. e Pull on the lock to verify that it is secured to the MP. f Remove the key. 11 Lift the MP access point into place on the universal mounting bracket as shown in Figure 12. Make sure the cable feeds properly into the ceiling as you lift the device, and does not become trapped between the access point and the bracket. Figure 12. Step 10Placing the MP Access Point on the Bracket 2 0 0 0
2 0 5 9
0 4 8 28 Trapeze Mobility Point Installation Guide Installing an MP-372 Chapter 3 12 Lock the MP access point onto the bracket by inserting the 3-mm or 1/8-inch screwdriver into the Lock hole on the access point as shown in Figure 13. Caution! To prevent possible damage to the MP access point, make sure the device is fully locked onto the bracket before letting go of it. Figure 13. Step 11Locking the Bracket Lock T-bar 6 0 0 0
2 0 5 9
0 4 8 13 To ensure that the MP access point is fully locked onto the bracket, gently pull down on the access point and attempt to rotate it from side to side. 14 If the access point comes off the bracket, relock the device onto the bracket as described in step 12 on page 29. 15 If the MP requires an external antenna, install and connect the antenna. (See Connecting an MP to an External Antenna on page 49.) 16 If the other ends of the Cat 5 cable(s) are not already connected and the link activated, go to Connecting an MP to an MX Switch on page 50. Otherwise, go to Verifying MP Health on page 52. Installing and Connecting an MP-372 29 Installing an MP-372 Chapter 3 Suspended Ceiling InstallationDrop Ceiling Tiles
(For required mounting hardware and tools, see Table 4 on page 22.) 1 Select an installation location that is centered over a T-bar in the ceiling. 2 Cut a hole as follows in the ceiling tile for the Cat 5 cable(s):
a Place the mounting template over the area where you plan to install the MP access point. b Use the box cutter to cut along the line marking the opening for the port connectors. c Remove the mounting template and the material you cut from the ceiling panel. 3 Install the T-bar clamp that fits the T-bar:
a Slide each half of the clamp onto the T-bar so that the clamp lip is fully on the T-bar. b Slide the two halves of the clamp toward each other until the tabs are inserted completely into the holes and the clamp fits snugly on the T-bar. Figure 14 shows an example for a 23.9-mm (15/16-inch) T-bar. Figure 15 shows an example for a 15.9-mm (5/8-inch) T-bar. Figure 14. Step 3Installing the T-bar Clamp for a 23.9-mm
(15/16-inch) T-bar T-bar T-bar clamp halves Slide together 3 0 0 0
2 0 5 9
0 4 8 30 Trapeze Mobility Point Installation Guide Installing an MP-372 Chapter 3 Figure 15. Step 3Installing the T-bar Clamp for a 15.9-mm
(5/8-inch) T-bar T-bar T-bar clamp halves Slide together 6 6 0 0
2 0 5 9
0 4 8 4 Unlock the universal mounting bracket from the MP access point by inserting the 3-mm or 1/8-inch screwdriver into the Unlock hole on the MP access point as shown in Figure 16. Caution! To avoid damage to the MP access points lock mechanism or electronic components, do not use excessive force when inserting a tool into the Unlock or Lock hole. Figure 16. Step 4Unlocking the Bracket 1 1 0 0
2 0 5 9
0 4 8 Installing and Connecting an MP-372 31 Installing an MP-372 Chapter 3 5 Remove the bracket as shown in Figure 17. Figure 17. Step 5Removing the Bracket 8 0 0 0
2 0 5 9
0 4 8 6 Install the universal mounting bracket as follows onto the T-bar clamp:
a As shown in Figure 18, place the universal mounting bracket against the T-bar clamp so that the two screw holes face downward and the two T-bar flanges face upward and are adjacent to the T-bar edges. b Properly align the bracket for mounting by placing the bracket so that its port connector opening is to the left of the hole you cut for the cables. c Rotate the universal mounting bracket clockwise until the flanges snap into place on the T-bar clamp as shown in Figure 19. 32 Trapeze Mobility Point Installation Guide Installing an MP-372 Chapter 3 Figure 18. Step 6Top View Universal mounting bracket T- bar T-bar clamps
(attached to T-bar) Port connector opening
(Viewed from above ceiling tiles, looking down.) Figure 19. Step 6Bottom View Port connector opening Universal mounting bracket T-bar 2 1 0 0
2 0 5 9
0 4 8 4 0 0 0
2 0 5 9
0 4 8 7 Pull the Cat 5 cable(s) about 15 cm (about 6 inches) out of the hole in the ceiling tile and through the port connector opening to create enough slack to insert the cable(s). 8 Insert the Cat 5 cable(s) into the connector(s):
For a single connection, use the connector for port 1. For redundancy, insert one cable into each connector. Installing and Connecting an MP-372 33 Installing an MP-372 Chapter 3 9 Install the Kensington lock, if you plan to used one. a Loop the Kensington locks cable around an object that cannot be moved or damaged by a person pulling on the cable. b Insert the key into the Kensington lock. Insert the Kensington lock into the security slot on the MP. c d Rotate the key right or left to secure the lock to the MP. e Pull on the lock to verify that it is secured to the MP. f Remove the key. 10 Lift the MP access point into place on the universal mounting bracket as shown in Figure 20. Make sure the cable feeds properly into the ceiling as you lift the device, and does not become trapped between the access point and the bracket. Figure 20. Step 9Placing the MP Access Point on the Bracket 2 0 0 0
2 0 5 9
0 4 8 11 Lock the MP access point onto the bracket by inserting the 3-mm or 1/8-inch screwdriver into the Lock hole on the access point as shown in Figure 21. Caution! To prevent possible damage to the MP access point, make sure the device is fully locked onto the bracket before letting go of it. 34 Trapeze Mobility Point Installation Guide Installing an MP-372 Chapter 3 Figure 21. Step 10Locking the Bracket Lock T-bar 6 0 0 0
2 0 5 9
0 4 8 12 To ensure that the MP access point is fully locked onto the bracket, gently pull down on the access point and attempt to rotate it from side to side. If the access point comes off the bracket, relock the device onto the bracket as described in step 11 on page 34. 13 If the MP requires an external antenna, install and connect the antenna. (See Connecting an MP to an External Antenna on page 49.) 14 If the other ends of the Cat 5 cable(s) are not already connected and the link activated, go to Connecting an MP to an MX Switch on page 50. Otherwise, go to Verifying MP Health on page 52. Installing and Connecting an MP-372 35 Installing an MP-372 Chapter 3 Junction Box Installation
(For required mounting hardware and tools, see Table 4 on page 22.) 1 Unlock the universal mounting bracket from the MP access point by inserting the 3-mm or 1/8-inch screwdriver into the Unlock hole on the MP access point as shown in Figure 22. Caution! To avoid damage to the MP access points lock mechanism or electronic components, do not use excessive force when inserting a tool into the Unlock or Lock hole. Figure 22. Step 1Unlocking the Bracket 2 Remove the bracket as shown in Figure 23. 1 1 0 0
2 0 5 9
0 4 8 36 Trapeze Mobility Point Installation Guide Figure 23. Step 2Removing the Bracket Installing an MP-372 Chapter 3 8 0 0 0
2 0 5 9
0 4 8 3 Attach the universal mounting bracket to the junction box as shown in Figure 24:
a Place the universal mounting bracket against the junction box so that the two screw holes face the junction box and align over the screw holes in the box. b Insert the #6-32 x 1-inch machine screws in the universal mounting brackets screw holes, and use a #2 Phillips-head screwdriver to tighten them. Installing and Connecting an MP-372 37 Installing an MP-372 Chapter 3 Figure 24. Step 3Placing the Bracket on the Junction Box Junction box Port connector opening 7 1 0 0
2 0 5 9
0 4 8 4 Pull the Cat 5 cable(s) about 15 cm (about 6 inches) out of the junction box and through the port connector opening to create enough slack to insert the cable(s) into the port connectors. 5 Insert the Cat 5 cable(s) into the connector(s):
For a single connection, use the connector for port 1. For redundancy, insert one cable into each connector. 6 Install the Kensington lock, if you plan to used one. a Loop the Kensington locks cable around an object that cannot be moved or damaged by a person pulling on the cable. b Insert the key into the Kensington lock. Insert the Kensington lock into the security slot on the MP. c d Rotate the key right or left to secure the lock to the MP. e Pull on the lock to verify that it is secured to the MP. f Remove the key. 38 Trapeze Mobility Point Installation Guide Installing an MP-372 Chapter 3 7 Lift the MP access point into place on the universal mounting bracket. Make sure the cable feeds properly into the junction box as you lift the device, and does not become trapped between the access point and the bracket. 8 Lock the MP access point onto the bracket by inserting the 3-mm or 1/8-inch screwdriver into the Lock hole on the access point as shown in Figure 25. Caution! To prevent possible damage to the MP access point, make sure the device is fully locked onto the bracket before letting go of it. Figure 25. Step 7Locking the Bracket Lock 2 6 0 0
2 0 5 9
0 4 8 9 To ensure that the MP access point is fully locked onto the bracket, gently pull down on the access point and attempt to rotate it from side to side. If the access point comes off the bracket, relock the device onto the bracket as described in step 8 on page 39. 10 If the MP requires an external antenna, install and connect the antenna. (See Connecting an MP to an External Antenna on page 49.) 11 If the other ends of the Cat 5 cable(s) are not already connected and the link activated, go to Connecting an MP to an MX Switch on page 50. Otherwise, go to Verifying MP Health on page 52. Installing and Connecting an MP-372 39 Installing an MP-372 Chapter 3 Solid Wall or Ceiling Installation Note. The solid surface mounting option requires Cat 5 cable that does not have strain relief, unless you plan to route the cable through a hole in the wall or ceiling. The other options can use Cat 5 cable with or without strain relief.
(For required mounting hardware and tools, see Table 4 on page 22.) 1 Prepare holes in the wall or ceiling for the universal mounting bracket, using the following steps:
a Place the paper mounting template over the location where you want to install the MP access point. b Mark the screw hole location(s). If you plan to route the Cat 5 cable externally along the wall or ceiling, mark the locations of both the center screw hole and the screw hole by the port connector opening. If you plan to route the Cat 5 cable through a hole in the wall or ceiling, mark the location of the center screw hole only. You cannot use the screw hole by the port connector opening if you cut a hole for the opening. Note. Do not mark the four holes on the edges of the bracket. (These are the holes indicated by the dashed lines in Figure 28.) The MP access point fits into these holes. They are not screw holes. c Remove the template. 2 Install the drywall anchor(s):
a Hammer a drywall anchor into each hole, up to the beginning of the threads on the anchor. b Screw each anchor the rest of the way into its hole using a
#2 Phillips-head screwdriver. c Remove the screw from each anchor and save the screw(s) for step 6 on page 42. 40 Trapeze Mobility Point Installation Guide Installing an MP-372 Chapter 3 3 Unlock the universal mounting bracket from the MP access point by inserting the 3-mm or 1/8-inch screwdriver into the Unlock hole on the MP access point as shown in Figure 26. Caution! To avoid damage to the MP access points lock mechanism or electronic components, do not use excessive force when inserting a tool into the Unlock or Lock hole. Figure 26. Step 3Unlocking the Bracket 1 1 0 0
2 0 5 9
0 4 8 4 Remove the bracket as shown in Figure 27. Figure 27. Step 4Removing the Bracket 8 0 0 0
2 0 5 9
0 4 8 Installing and Connecting an MP-372 41 Installing an MP-372 Chapter 3 5 As shown in Figure 28, feed the Cat 5 cable(s) through the port connector opening and align the universal mounting bracket over the drywall anchors so that the two screw holes in the bracket face the drywall anchors. 6 Insert the #6 sheet metal screws into the screw holes, and tighten them to secure the universal mounting bracket to the wall or ceiling.
(If you routed the Cat 5 cable through a hole in the wall or ceiling, insert the screw into the center screw hole only.) Note. Do not insert screws in the four holes on the edges of the bracket. (These are the holes indicated by the dashed lines in Figure 28.) The MP access point fits into these holes. They are not screw holes. Figure 28. Steps 5 and 6Bracket Placement on Solid Wall or Ceiling 5 1 0 0
2 0 5 9
0 4 8 42 Trapeze Mobility Point Installation Guide Installing an MP-372 Chapter 3 7 Insert the Cat 5 cable(s) into the connector(s):
For a single connection, use the connector for port 1. For redundancy, insert one cable into each connector. 8 Install the Kensington lock, if you plan to used one. a Loop the Kensington locks cable around an object that cannot be moved or damaged by a person pulling on the cable. b Insert the key into the Kensington lock. Insert the Kensington lock into the security slot on the MP. c d Rotate the key right or left to secure the lock to the MP. e Pull on the lock to verify that it is secured to the MP. f Remove the key. 9 As shown in Figure 29, place the MP access point on the bracket, making sure to remove any slack that occurs in the cable between the bracket and the MP access point. Figure 29. Step 8Cable Placement Cable Universal mounting bracket 6 1 0 0
2 0 5 9
0 4 8 Installing and Connecting an MP-372 43 Installing an MP-372 Chapter 3 10 Lock the MP access point onto the bracket by inserting the 3-mm or 1/8-inch screwdriver into the Lock hole on the access point as shown in Figure 30. Caution! To prevent possible damage to the MP access point, make sure the device is fully locked onto the bracket before letting go of it. Figure 30. Step 9Locking the Bracket Lock 2 6 0 0
2 0 5 9
0 4 8 11 To ensure that the MP access point is fully locked onto the bracket, gently pull on the access point and attempt to rotate it from side to side. If the access point comes off the bracket, relock the device onto the bracket as described in step 10 on page 44. 12 If the MP requires an external antenna, install and connect the antenna. (See Connecting an MP to an External Antenna on page 49.) 13 If the other ends of the Cat 5 cable(s) are not already connected and the link activated, go to Connecting an MP to an MX Switch on page 50. Otherwise, go to Verifying MP Health on page 52. 44 Trapeze Mobility Point Installation Guide Installing an MP-372 Chapter 3 Tabletop Installation
(For required mounting hardware and tools, see Table 4 on page 22.) 1 Reverse the universal mounting bracket:
a Unlock the universal mounting bracket from the MP access point by inserting the 3-mm or 1/8-inch screwdriver into the Unlock hole on the MP access point as shown in Figure 31. Caution! To avoid damage to the MP access points lock mechanism or electronic components, do not use excessive force when inserting a tool into the Unlock or Lock hole. Figure 31. Step 1aUnlocking the Bracket 1 1 0 0
2 0 5 9
0 4 8 Installing and Connecting an MP-372 45 Installing an MP-372 Chapter 3 b Remove the bracket as shown in Figure 32. Figure 32. Step 1bRemoving the Bracket 8 0 0 0
2 0 5 9
0 4 8 c Turn over the universal mounting bracket, then align the bracket over the cable ports and the four mounting posts as shown in Figure 33. Figure 33. Step 1cTurning Over the Bracket 1 6 0 0
2 0 5 9
0 4 8 d Once the bracket is fully seated, lock the bracket onto the MP access point by inserting the 3-mm or 1/8-inch screwdriver into the Lock hole on the access point as shown in Figure 34. 46 Trapeze Mobility Point Installation Guide Figure 34. Step 1dLocking the Bracket Installing an MP-372 Chapter 3 Lock 2 6 0 0
2 0 5 9
0 4 8 2 Attach the three rubber adhesive feet onto the universal mounting bracket, in the three location circles, as shown in Figure 35. Figure 35. Step 2Installing the Rubber Feet 3 1 0 0
2 0 5 9
0 4 8 3 Insert the Cat 5 cable(s) into the connector(s):
For a single connection, use the connector for port 1. For redundancy, insert one cable into each connector. Installing and Connecting an MP-372 47 Installing an MP-372 Chapter 3 4 Install the Kensington lock, if you plan to used one. a Loop the Kensington locks cable around an object that cannot be moved or damaged by a person pulling on the cable. b Insert the key into the Kensington lock. Insert the Kensington lock into the security slot on the MP. c d Rotate the key right or left to secure the lock to the MP. e Pull on the lock to verify that it is secured to the MP. f Remove the key. 5 Place the MP access point in the desired location on the table. 6 If the MP requires an external antenna, install and connect the antenna. (See Connecting an MP to an External Antenna on page 49.) 7 If the other ends of the Cat 5 cable(s) are not already connected and the link activated, go to Connecting an MP to an MX Switch on page 50. Otherwise, go to Verifying MP Health on page 52. 48 Trapeze Mobility Point Installation Guide Installing an MP-372 Chapter 3 Connecting an MP to an External Antenna Each radio in an MP-372 can use an optional Trapeze external antenna. To mount the antenna, see the instructions that come with the antenna. Caution! The external antenna must be installed at least 20 cm from the MP access point. To connect a mounted external antenna to an MP-372:
1 Attach the exterior antenna cable that is shipped with the antenna to the MP external antenna connector. Both connectors are labeled to indicate the radio type. The MP has standard SMA connectors for attachment to the 802.11b/g antenna and to the 802.11a antenna.
(For the location of the external antenna connectors, see Figure 2 on page 8.) Caution! The external connectors on the MP are labeled: 11B/G and 11A. Each connector is a standard SMA connector. Make sure you attach the antenna to the correct connector. Note. If the MP is installed in a Trapeze Networks outdoor MP enclosure, attach the antenna cable to the lightning surge arrestor (if installed) or the enclosures SMA bulkhead connector. 2 Attach the other end of the antenna cable to the antenna. 3 If the other ends of the Cat 5 cable(s) are not already connected and the link activated, go to Connecting an MP to an MX Switch on page 50. Otherwise, go to Verifying MP Health on page 52. Installing and Connecting an MP-372 49 Connecting an MP to an MX Switch Chapter 3 Connecting an MP to an MX Switch You can connect an MP access point directly to an MX switch or indirectly to the switch through an intermediate Layer 2 or Layer 3 network. To connect the MP directly to an MX switch, configure the MX switch port as an MP access port and use the following procedure to insert the cable into the MX switch and verify the link. To connect the MP indirectly to an MX switch though the network, configure a Distributed MP connection on the MX switch. You can use the CLI or RingMaster to configure an MP access port or Distributed MP connection. (See the Trapeze Mobility System Software Configuration Guide or the Trapeze RingMaster Users Guide.) Figure 36 shows how to insert a Cat 5 cable into 10/100 Ethernet port on an MX switch. Refer to this figure as you perform the procedure. Figure 36. 10/100 Cat 5 Cable Installation Ethernet port Mobility Exchange MX-20 Ethernet cable
(Cat 5 cable) MP, switch, server or other device 8 5 0 0
2 0 5 9
0 4 8 1 Insert a Cat 5 cable with a standard RJ-45 connector as shown in Figure 36. For connection to an MP access point, use a straight-through cable. 50 Trapeze Mobility Point Installation Guide Connecting an MP to an MX Switch Chapter 3 2 When the link is activated, observe the MP LED for the port on the MX switch:
MP LED Appearance Solid green Alternating green and amber Solid amber Blinking amber Unlit Meaning For an MP access points active link, all the following are true:
MP access point has booted. MP access point has received a valid configuration from the MX switch. Management link with an MP access point is At least one radio is enabled or is in sentry operational. mode. For an MP access points secondary link, the link is present. MP access point is booting with an image received from the MX switch. After the access point boots and receives its configuration, this LED appearance persists until a radio is enabled or is placed in sentry mode. PoE is on. MP is unresponsive or there is a PoE problem. PoE is off. Note. An MX switchs 10/100 Ethernet ports are configured as wired network ports by default. You or the system administrator must change the port type for an MX port directly connected to an MP to activate the link. (See the Trapeze Mobility Exchange Installation and Basic Configuration Guide.) Installing and Connecting an MP-372 51 Verifying MP Health Chapter 3 Verifying MP Health After you install the MP access point and enable PoE on the Ethernet cable connected to the MP, you can easily verify the MPs status by observing the LEDs, particularly the health LED. (See Figure 4 on page 12.) The health or LINK LED indicates whether the MP access point is ready for operation. If the LED is green and glowing steadily, the MP has been booted successfully by the MX switch and is ready for operation. If the LED is not steadily glowing green, contact the system administrator for the MX switch or, if you are the system administrator, see Appendix A, MP Troubleshooting, on page 53. 52 Trapeze Mobility Point Installation Guide A MP Troubleshooting After you insert a Cat 5 cable into an MP access points port connector and enable PoE on the cable, observe the devices health or LINK LED to determine the status of the connection with the MX switch. If the LED is green and is glowing steadily, the MP has been booted successfully by the MX switch and is ready for operation. If the LED is not steadily glowing green, see Table 5.
(For descriptions of all the LEDs, see Status LEDs on page 12.) MP Troubleshooting 53 Appendix A Table 5. Health LED States Health or LINK LED Appearance Not solid green Diagnosis Remedy MP radio needs to be enabled. Unlit MP access point is not receiving power. Enable at least one of the radios. If the LED is still not solid green, try the remedy listed in this table based on the LEDs appearance. Check the Cat 5 cable connection(s). For a direct connection to an MX switch:
Set the port type on the MX switch to an MP port. Verify that Power over Ethernet
(PoE) is enabled on the MX switch port connected to the MP access point. For an indirect connection through the network:
Configure a Distributed MP connection on an MX switch. Verify that a Trapeze-approved PoE source is supplying power to the MP. Slowly alternating green and amber MP access point is booting with an image received from an MX switch. Solid amber MP access point is waiting to receive boot instructions and a configuration file from an MX switch. Wait a few seconds for the boot process to complete. If this LED appearance persists, enable a radio or place a radio in sentry mode. Wait a few seconds for the boot process to begin. If the LED remains amber, try the remedies for the other health LED appearances. If the LED still remains amber, make sure the MP access point is securely connected to its PoE source and to the network or MX switch. 54 Trapeze Mobility Point Installation Guide B MP Technical Specifications This appendix lists the technical specifications for the Trapeze Networks MP-372 access point. Table 6 lists the mechanical and compliance specifications. (For detailed compliance information, see the Trapeze Regulatory Information document.) Table 7, Table 8, and Table 9 list the radio specifications. Table 10 lists the MAC address allocation scheme.
(For specifications for the MX switch, see the Trapeze Mobility Exchange Installation and Basic Configuration Guide.) Note. This Listed Accessory is designed and approved to be used only with Trapeze Networks Mobility Exchange (MX) models MX-20, MX-8, and MXR-2.
(The MX-400 switch does not directly connect to the MP.) Note. The MP radios are disabled by default and can be enabled only by the system administrator using the RingMaster management application or the MX switchs command-line interface (CLI). Note. The radio frequency band, operating channels, and transmit power depend on the country of operation specified by the system administrator using RingMaster or the MX switchs CLI. MP Technical Specifications 55 Appendix B Table 6. MP Mechanical and Compliance Specifications Specification Size Weight Operating Temperature Storage Temperature Humidity Power over Ethernet
(PoE) Status indicators Wired network ports Standards compliance Safety and electromagnetic compliance Description Diameter: 16.76 cm (6.6 inches) Height: 4.69 cm (1.85 inches) Without mounting bracket: 0.35 kg (12.5 ounces) With mounting bracket: 0.40 kg (14 ounces) 0 C to +50 C (32 F to 122 F)
-20 C to +70 C (-4 F to +158 F) 10% to 95% noncondensing 42 VDC to 57 VDC (46 VDC nominal) IEEE 802.3af (MP-341, MP-352, and MP-52) Health/MX and radio LEDs
(For descriptions of the LEDs, see Status LEDs on page 12.) Two RJ-45 ports for 10/100BASE-T Ethernet and Power over Ethernet (PoE) IEEE 802.11 IEEE 802.11a IEEE 802.11b IEEE 802.11g IEEE 802.3af FCC Part 15, UL 60950 IC Part 15, CSA 22.2 N0-950, RSS-139-1 and RSS-210 ETS 300 328 (2.4 GHz) and 301 893 (5 GHz), EN 301 489-17 R&TTE Directive 1999/5/EC TELEC, ARIB T66 GBT-15941-1995, GBT-16841-1997 LP0002 56 Trapeze Mobility Point Installation Guide Appendix B Table 6. MP Mechanical and Compliance Specifications (continued) Specification Encryption General Description Wi-Fi Protected Access (WPA) Advanced Encryption Standard (AES) 40-bit/104-bit Wired-Equivalent Privacy (WEP) Power-save mode supported Transmit power control in 1 dBm increments Supports up to 250 clients per radio Table 7. 802.11a Radio Specifications Specification Antenna type Antenna gain Frequency band Operating channels Association rates Modulation Transmit power Description Integrated diversity omnidirectional External sectorized or directional (optional) Internal: 2 dBi External:
ANT-506014.5 dBi ANT-512012.5 dBi ANT-518010.8 dBi 5.15 GHz to 5.85 GHz based on country regulations Based on the country of operation specified by the system administrator 54 Mbps, 48 Mbps, 36 Mbps, 24 Mbps, 18 Mbps, 12 Mbps, 9 Mbps, and 6 Mbps, with automatic fallback Orthogonal frequency division multiplexing (OFDM) Based on the country of operation specified by the system administrator MP Technical Specifications 57 Appendix B Table 8. 802.11b Radio Specifications Specification Antenna type Antenna gain Frequency band Operating channels Association rates Modulation Transmit power Description Integrated diversity omnidirectional External sectorized or directional (optional) Internal: 2 dBi External:
ANT-1060greater than 10 dBi ANT-11207 dBi or more ANT-11806 dBi or more 2.4 GHz to 2.4835 GHz based on country regulations Based on the country of operation specified by the system administrator 11 Mbps, 5.5 Mbps, 2 Mbps, and 1 Mbps, with automatic fallback Direct-sequence spread-spectrum (DSSS) Based on the country of operation specified by the system administrator Table 9. 802.11g Radio Specifications Specification Antenna type Antenna gain Frequency band Operating channels Description Integrated diversity omnidirectional External sectorized or directional (optional) Internal: 2 dBi External:
ANT-1060greater than 10 dBi ANT-11207 dBi or more ANT-11806 dBi or more 2.4 GHz to 2.4835 GHz based on country regulations Based on the country of operation specified by the system administrator 58 Trapeze Mobility Point Installation Guide Appendix B Table 9. 802.11g Radio Specifications (continued) Specification Association rates Modulation Transmit power Description 54 Mbps, 48 Mbps, 36 Mbps, 24 Mbps, 18 Mbps, 12 Mbps, 9 Mbps, and 6 Mbps, with automatic fallback Orthogonal frequency division multiplexing (OFDM) Based on the country of operation specified by the system administrator MAC Addresses Each MP-372 is assigned a unique block of 64 MAC addresses. Each radio has 32 MAC addresses and can therefore support up to 32 SSIDs, with one MAC address assigned to each SSID as its BSSID. An MPs MAC address block is listed on a label on the back of the MP. If the MP is already deployed and running on the network, you can display the MAC address assignments by using the show {ap | dap} status command. All MAC addresses on an MP are assigned based on the MPs base MAC address, as described in Table 10. Table 10. MAC Address Allocations on MP-372 MP base MAC Address Ethernet Port MAC Addresses 802.11a Radio and SSID MAC Addresses 802.11b/g Radio and SSID MAC Addresses The MP has a base MAC address. All the other addresses are assigned based on this address. Ethernet port 1 equals the MP base MAC address. Ethernet port 2 equals the MP base MAC address + 1. The 802.11a radio equals the MP base MAC address + 1. The BSSIDs for the SSIDs configured on the 802.11a radio end in odd numbers. The first BSSID is equal to the MPs base MAC address + 1. The next BSSID is equal to the MPs base MAC address + 3, and so on. The 802.11b/g radio equals the MP base MAC address. The BSSIDs for the SSIDs configured on the 802.11b/g radio end in even numbers. The first BSSID is equal to the MPs base MAC address. The next BSSID is equal to the MPs base MAC address + 2, and so on. MP Technical Specifications 59 Appendix B 60 Trapeze Mobility Point Installation Guide C Translated Warning Conventions and Warnings The following warning conventions and warnings apply to this manual. Warning Conventions Warning! This situation or condition can cause injury. Waarschuwing! Deze situatie of omstandigheid kan letsel veroorzaken. Warnung! Diese Situation oder dieser Zustand kann zu Verletzungen fhren. Avertissement ! Cette situation ou cette condition peuvent provoquer des blessures. Aviso Esta situacin o condicin puede causar lesiones. Translated Warning Conventions and Warnings 61 Appendix C Warning! High voltage. This situation or condition can cause injury due to electric shock. Waarschuwing! Hoog voltage. Deze situatie of omstandigheid kan letsel veroorzaken door elektrische schokken. Warnung! Hochspannung. Diese Situation oder dieser Zustand kann einen Elektroschock verursachen. Avertissement ! Haute tension. Cette situation ou cette condition peuvent provoquer des blessures dues des dcharges lectriques. Aviso Alta tensin. Esta situacin o condicin puede causar lesiones por descarga elctrica. Warning! Radiation. This situation or condition can cause injury due to improper handling of fiber-optic equipment. Waarschuwing! Straling. Deze situatie of omstandigheid kan letsel veroorzaken door onjuist gebruik van glasvezelapparatuur. Warnung! Strahlung. Diese Situation oder dieser Zustand kann durch falschen Umgang mit glasfaserbasierten Gerten zu Verletzungen fhren. Avertissement ! Radiation. Cette situation ou cette condition peuvent provoquer des blessures dues une manipulation inapproprie dappareils quips de fibres optiques. Aviso Radiacin. Esta situacin o condicin puede causar lesiones debido a un manejo inadecuado del equipamiento de fibra ptica. 62 Trapeze Mobility Point Installation Guide Qualified Service Personnel Warning Appendix C Warning! Installation must be performed by qualified service personnel only. Read and follow all warning notices and instructions marked on the product or included in the documentation. Before installing the product, read the Trapeze Regulatory Information document. Waarschuwing! De installatie mag alleen worden uitgevoerd door bevoegd onderhoudspersoneel. Het is essentieel dat u kennis neemt van alle waarschuwingen en instructies aangebracht op het product zelf en/of opgenomen in de documentatie. Voordat u het product installeert, dient u Trapeze Regulatory Information in zijn geheel te hebben gelezen. Warnung! Die Installation darf nur von einem qualifizierten Kundendienstmitarbeiter vorgenommen werden. Lesen Sie alle Warnhinweise und Anweisungen auf dem Produkt oder in der Dokumentation und befolgen Sie sie. Bevor Sie das Produkt installieren, sollten Sie Trapeze Regulatory Information vollstndig lesen. Avertissement ! Linstallation doit tre effectue uniquement par des techniciens qualifis. Lisez et suivez toutes les notices davertissement et les instructions figurant sur le produit ou comprises dans la documentation. Lisez l Trapeze Regulatory Information avant dinstaller ce produit. Aviso Slo puede realizar la instalacin personal cualificado de asistencia tcnica. Lea y siga todas las notas de advertencia e instrucciones indicadas en el producto o incluidas en la documentacin. Antes de instalar el producto, lea Trapeze Regulatory Information. Translated Warning Conventions and Warnings 63 Appendix C Radio Safety Warnings Warning! Do not operate the MP access point near unshielded blasting caps or in an otherwise explosive environment unless the device has been modified for such use by qualified personnel. Waarschuwing! Het MP-toegangspunt mag niet worden gebruikt in de nabijheid van onafgeschermde slaghoedjes of in een andere explosieve omgeving tenzij het apparaat voor een dergelijk gebruik is aangepast door bevoegd personeel. Warnung! Die MP-Zugriffspunkte sollten nicht neben ungeschirmten Sprengkapseln betrieben oder in einer explosiven Umgebung eingesetzt werden. Fr einen solchen Einsatz muss das Gert von einem qualifizierten Kundendienstmitarbeiter entsprechend angepasst werden. Avertissement ! Le point daccs MP ne doit pas fonctionner prs de dtonateurs non blinds ou dans un autre environnement qui prsent un risque dexplosion, moins que cet appareil nait t adapt en vue dune telle utilisation par du personnel qualifi. Aviso No utilice el punto de acceso de MP cerca de detonadores no blindados ni en un entorno explosivo, a menos que haya sido modificado el dispositivo con ese fin por personal cualificado. 64 Trapeze Mobility Point Installation Guide Appendix C Warning! Do not touch or move the MP access point when the antennas are transmitting or receiving. Waarschuwing! Het MP-toegangspunt mag niet worden aangeraakt of verplaatst terwijl de antennes uitzenden of ontvangen. Warnung! Berhren oder bewegen Sie den MP-Zugriffspunkt nicht, whrend die Antennen senden oder empfangen. Avertissement ! Ne touchez ni ne dplacez le point daccs MP lorsque les antennes sont en cours de transmission ou de rception. Aviso No toque ni mueva el punto de acceso de MP cuando las antenas estn transmitiendo o recibiendo seales. Warning! Do not hold any radio device so that the antenna is very close to or touching the face, eyes, or other exposed body part while the device's radio antenna is transmitting. Waarschuwing! De antenne van een apparaat dat radiogolven aan het uitzenden is, mag nooit vlakbij of tegen het gezicht, de ogen of een andere onbedekt deel van het lichaam worden gehouden. Warnung! Halten Sie die drahtlosen Gerte whrend der bertragung mit der Antenne nicht nahe ans Gesicht, an die Augen oder an andere ungeschtzte Krperteile und berhren Sie die Antenne nicht. Avertissement ! Ne maintenez pas lantenne dun appareil radio prs du visage, des yeux ou dune autre partie du corps expose ou en contact avec ces parties du corps, lorsquelle est en cours de transmission. Aviso No coloque ningn dispositivo de radio demasiado cerca de la antena ni en contacto con la cara, los ojos u otras partes del cuerpo que estn al descubierto mientras la antena de radio del dispositivo est transmitiendo seales. Translated Warning Conventions and Warnings 65 Appendix C Warning! Before using a wireless device in a hazardous location, consult the local codes, national codes, and safety directors of the location for usage constraints. Waarschuwing! Voordat u een draadloos apparaat gebruikt op een gevaarlijke locatie, dient u de plaatselijke en landelijke voorschriften, en de veiligheidsvoorschriften voor de locatie te raadplegen over eventuele gebruiksbeperkingen. Warnung! Bevor Sie drahtlose Gerte an einem gefhrlichen Standort einsetzen, sollten Sie die lokalen und nationalen Regelungen und Sicherheitsbestimmungen des Standorts auf Nutzungsbeschrnkungen berprfen. Avertissement ! Avant dutiliser un appareil sans fil dans un endroit dangereux, consultez la rglementation locale et nationale ainsi que les responsables de la scurit de lendroit concern pour obtenir des informations relatives aux conditions et aux limites dutilisation de cet appareil. Aviso Antes de utilizar un dispositivo inalmbrico en una ubicacin peligrosa, consulte los cdigos locales y nacionales y a los responsables de seguridad de la ubicacin para conocer las restricciones de uso. 66 Trapeze Mobility Point Installation Guide Lightning Warning Appendix C Warning! Do not connect or disconnect cables or otherwise work with the MP access point hardware during periods of lightning activity. Waarschuwing! Tijdens onweer met bliksem mogen kabels nooit worden aangekoppeld aan of losgekoppeld van het MP-toegangspunt of andere werkzaamheden aan het MP-toegangspunt worden verricht. Warnung! Verbinden und trennen Sie whrend eines Gewitters keine Kabel zum MP-Zugriffspunkt und arbeiten Sie nicht damit. Avertissement ! Ne connectez pas et ne dconnectez pas de cbles et, de manire gnrale, ne travaillez pas sur le matriel du point daccs MP lorsquil y a un risque de foudre. Aviso No conecte ni desconecte cables, ni tampoco trabaje con el hardware del punto de acceso de MP durante una tormenta elctrica. Translated Warning Conventions and Warnings 67 Appendix C 68 Trapeze Mobility Point Installation Guide Index A access point. See MP (Mobility Point) activating an MP 50 advisory notices, explanations of 4 ANT-1060 10 ANT-1120 10 ANT-1180 10 ANT-5060 10 ANT-5120 10 ANT-5180 10 antennas, external 10 B bracket 12 C cable ports 9 cable requirements 20 solid surface 40 Category 5 cables 9 strain relief 40 ceiling installation drop tiles 30 solid 40 suspended, flush tiles 24 connections dual-homed 9 external antenna 49 LEDs 51 MX (Mobility Exchange) 50 troubleshooting 53 conventions, text and syntax 5 customer service iii D documentation conventions 5 documentation, product 2 drop ceiling installation 30 dual-homed connections 9 E Ethernet cable requirements 20 connections to an MX switch, instructions connections to an MX switch, MP port 50 locations 9 LEDs 51 ports 9 external antenna connections to an MP, instructions 49 external antennas 10 F flush ceiling installation 24 H hardware bottom view 8 features 8 inventory 16 mounting bracket 12 required, list of 22 top view 8 Index 69 health LED description 13 troubleshooting with 53 verifying MP health with 52 I installation junction box 36 MP 15, 22 requirements 18 requirements, tools 22 solid surface 40 suspended ceilings 30 suspended ceilings, flush tiles 24 tabletop 45 T-bar ceilings. See suspended ceilings warnings, cables 20 warnings, radio 19 warnings, service 7 warnings, translations 61 IP addresses 59 J junction box installation 36 K Kensington security slot 12 L LEDs 12 health 13, 52, 53 MP (on MX) 51 radio 13 links dual-homed 9 LEDs 51 MP 51 troubleshooting 53 M MAC addresses 59 manuals, product 2 Mobility Exchange. See MX Mobility Point. See MP model numbers external antennas 10 mounting bracket 12 mounting options 12 MP (Mobility Point) description of 7 installation 15, 22 specifications 55 troubleshooting 53 warnings 61 MX (Mobility Exchange) connections 14, 50 MP LEDs 51 recommendation 18 N network plan, RingMaster 18 P PoE (Power over Ethernet) dual-homed connections 9 pin signals 21 specifications 56 use with Trapeze devices only 18 ports 9 product documentation 2 R radio LEDs 13 radios default state 7 health 53 radio LEDs 13 specifications 55 status 13 70 Trapeze Mobility Point Installation Guide troubleshooting 53 warnings 19 redundancy 9 requirements 18 cables 20 hardware 22 RingMaster wall installation recommendations 19 work order 18 RJ-45s 9 S safety notices, explanations of 4 solid surface installation 40 specifications 55 status LEDs. See LEDs status lights. See LEDs suspended ceilings, installation drop tiles 30 flush tiles 24 switch. See MX (Mobility Exchange) syntax conventions 5 T tabletop installation 45 TAC (Technical Assistance Center) iii T-bar ceilings. See suspended ceilings Technical Assistance Center iii technical specifications 55 technical support iii tools 22 translated warnings 61 Trapeze customer service iii Trapeze Networks Mobility System 1 troubleshooting 53 U universal mounting bracket 12 unpacking an MP 16 W wall installation junction box 36 recommendations 19 solid 40 warnings cable 20 installation 7 radio 19 translations 61 work order, RingMaster 18 Index 71 72 Trapeze Mobility Point Installation Guide
frequency | equipment class | purpose | ||
---|---|---|---|---|
1 | 2007-03-08 | 5180 ~ 5240 | NII - Unlicensed National Information Infrastructure TX | Class II permissive change or modification of presently authorized equipment |
2 | 5745 ~ 5825 | DTS - Digital Transmission System | ||
3 | 2005-05-21 | 5260 ~ 5320 | NII - Unlicensed National Information Infrastructure TX | |
4 | 5745 ~ 5825 | DTS - Digital Transmission System | ||
5 | 2005-03-28 | 5260 ~ 5320 | NII - Unlicensed National Information Infrastructure TX | Original Equipment |
6 | 5745 ~ 5825 | DTS - Digital Transmission System |
app s | Applicant Information | |||||
---|---|---|---|---|---|---|
1 2 3 4 5 6 | Effective |
2007-03-08
|
||||
1 2 3 4 5 6 |
2005-05-21
|
|||||
1 2 3 4 5 6 |
2005-03-28
|
|||||
1 2 3 4 5 6 | Applicant's complete, legal business name |
Juniper Networks, Inc.
|
||||
1 2 3 4 5 6 | FCC Registration Number (FRN) |
0004536603
|
||||
1 2 3 4 5 6 | Physical Address |
1133 Innovation Way
|
||||
1 2 3 4 5 6 |
Sunnyvale, California 94089
|
|||||
1 2 3 4 5 6 |
United States
|
|||||
app s | TCB Information | |||||
1 2 3 4 5 6 | TCB Application Email Address |
b******@phoenix-testlab.de
|
||||
1 2 3 4 5 6 |
T******@TIMCOENGR.COM
|
|||||
1 2 3 4 5 6 | TCB Scope |
A4: UNII devices & low power transmitters using spread spectrum techniques
|
||||
app s | FCC ID | |||||
1 2 3 4 5 6 | Grantee Code |
QZE
|
||||
1 2 3 4 5 6 | Equipment Product Code |
200
|
||||
app s | Person at the applicant's address to receive grant or for contact | |||||
1 2 3 4 5 6 | Name |
M******** G********
|
||||
1 2 3 4 5 6 | Title |
Sr. Manager Compliance Engineering
|
||||
1 2 3 4 5 6 | Telephone Number |
(408)********
|
||||
1 2 3 4 5 6 | Fax Number |
(408)********
|
||||
1 2 3 4 5 6 |
m******@juniper.net
|
|||||
app s | Technical Contact | |||||
1 2 3 4 5 6 | Firm Name |
Sporton International Inc.
|
||||
1 2 3 4 5 6 |
Sporton International Inc
|
|||||
1 2 3 4 5 6 | Name |
W****** H********
|
||||
1 2 3 4 5 6 | Physical Address |
No. 52. Hwa Ya 1st Rd., Hwa Ya Technology Park
|
||||
1 2 3 4 5 6 |
No. 52, Hwa Ya 1st Rd., Kwei Shan
|
|||||
1 2 3 4 5 6 |
No. 52, Hwa Ya 1st. Rd., Kwei Shan
|
|||||
1 2 3 4 5 6 |
Tao Yaun, 333
|
|||||
1 2 3 4 5 6 |
Tao Yuan, 333
|
|||||
1 2 3 4 5 6 |
Tao Yuan
|
|||||
1 2 3 4 5 6 |
Taiwan
|
|||||
1 2 3 4 5 6 | Telephone Number |
+886 ******** Extension:
|
||||
1 2 3 4 5 6 | Fax Number |
+886 ********
|
||||
1 2 3 4 5 6 |
w******@sporton.com.tw
|
|||||
app s | Non Technical Contact | |||||
n/a | ||||||
app s | Confidentiality (long or short term) | |||||
1 2 3 4 5 6 | Does this application include a request for confidentiality for any portion(s) of the data contained in this application pursuant to 47 CFR § 0.459 of the Commission Rules?: | No | ||||
1 2 3 4 5 6 | Yes | |||||
1 2 3 4 5 6 | Long-Term Confidentiality Does this application include a request for confidentiality for any portion(s) of the data contained in this application pursuant to 47 CFR § 0.459 of the Commission Rules?: | No | ||||
if no date is supplied, the release date will be set to 45 calendar days past the date of grant. | ||||||
app s | Cognitive Radio & Software Defined Radio, Class, etc | |||||
1 2 3 4 5 6 | Is this application for software defined/cognitive radio authorization? | No | ||||
1 2 3 4 5 6 | Equipment Class | NII - Unlicensed National Information Infrastructure TX | ||||
1 2 3 4 5 6 | DTS - Digital Transmission System | |||||
1 2 3 4 5 6 | Description of product as it is marketed: (NOTE: This text will appear below the equipment class on the grant) | Dual mode 2.4GHz/5GHz Access Point | ||||
1 2 3 4 5 6 | Dual Mode 2.4GHz / 5GHz Access Point | |||||
1 2 3 4 5 6 | Dual Mode 2.4GHz/5GHz Access Point | |||||
1 2 3 4 5 6 | DUAL MODE 2.4GHz / 5GHz ACCESS POINT | |||||
1 2 3 4 5 6 | Related OET KnowledgeDataBase Inquiry: Is there a KDB inquiry associated with this application? | No | ||||
1 2 3 4 5 6 | Modular Equipment Type | Does not apply | ||||
1 2 3 4 5 6 | Purpose / Application is for | Class II permissive change or modification of presently authorized equipment | ||||
1 2 3 4 5 6 | Original Equipment | |||||
1 2 3 4 5 6 | Composite Equipment: Is the equipment in this application a composite device subject to an additional equipment authorization? | No | ||||
1 2 3 4 5 6 | Yes | |||||
1 2 3 4 5 6 | Related Equipment: Is the equipment in this application part of a system that operates with, or is marketed with, another device that requires an equipment authorization? | No | ||||
1 2 3 4 5 6 | Grant Comments | This is a Class II permissive change filing. Power listed is conducted. This device requires professional installations. Operation in the band 5.15~5.25GHz is restricted to indoor use only. The antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter. End-users and installers must be provided with antenna installation and transmitter operating conditions for satisfying RF exposure compliance. | ||||
1 2 3 4 5 6 | This is a Class II permissive change filing. Power listed is conducted. This device requires professional installations. The antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter. End-users and installers must be provided with antenna installation and transmitter operating conditions for satisfying RF exposure compliance. | |||||
1 2 3 4 5 6 | Power listed is conducted. This device requires professional installations. Operation in the band 5.15-5.25GHz is restricted to indoor use only. The antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter. End-users and installers must be provided with antenna installation and transmitter operating conditions for satisfying RF exposure compliance. | |||||
1 2 3 4 5 6 | Power listed is conducted. This device requires professional installations. The antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter. End-users and installers must be provided with antenna installation and transmitter operating conditions for satisfying RF exposure compliance. | |||||
1 2 3 4 5 6 | Is there an equipment authorization waiver associated with this application? | No | ||||
1 2 3 4 5 6 | If there is an equipment authorization waiver associated with this application, has the associated waiver been approved and all information uploaded? | No | ||||
app s | Test Firm Name and Contact Information | |||||
1 2 3 4 5 6 | Firm Name |
Sporton International Inc.
|
||||
1 2 3 4 5 6 |
SPORTON International Inc
|
|||||
1 2 3 4 5 6 | Name |
W****** H********
|
||||
1 2 3 4 5 6 |
K**** L****
|
|||||
1 2 3 4 5 6 | Telephone Number |
886-2******** Extension:
|
||||
1 2 3 4 5 6 | Fax Number |
886-2********
|
||||
1 2 3 4 5 6 |
k******@sporton.com.tw
|
|||||
1 2 3 4 5 6 |
k******@sporton.com.tw
|
|||||
Equipment Specifications | |||||||||||||||||||||||||||||||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
Line | Rule Parts | Grant Notes | Lower Frequency | Upper Frequency | Power Output | Tolerance | Emission Designator | Microprocessor Number | |||||||||||||||||||||||||||||||||
1 | 1 | 15E | CC | 5180.00000000 | 5240.00000000 | 0.0484170 | |||||||||||||||||||||||||||||||||||
Line | Rule Parts | Grant Notes | Lower Frequency | Upper Frequency | Power Output | Tolerance | Emission Designator | Microprocessor Number | |||||||||||||||||||||||||||||||||
2 | 1 | 15C | CC | 2412 | 2462 | 0.128825 | |||||||||||||||||||||||||||||||||||
2 | 2 | 15C | CC | 5745 | 5825 | 0.1 | |||||||||||||||||||||||||||||||||||
Line | Rule Parts | Grant Notes | Lower Frequency | Upper Frequency | Power Output | Tolerance | Emission Designator | Microprocessor Number | |||||||||||||||||||||||||||||||||
3 | 1 | 15E | CC | 5180 | 5240 | 0.048417 | |||||||||||||||||||||||||||||||||||
3 | 2 | 15E | CC | 5260 | 5320 | 0.144877 | |||||||||||||||||||||||||||||||||||
Line | Rule Parts | Grant Notes | Lower Frequency | Upper Frequency | Power Output | Tolerance | Emission Designator | Microprocessor Number | |||||||||||||||||||||||||||||||||
4 | 1 | 15C | CC | 2412 | 2462 | 0.128825 | |||||||||||||||||||||||||||||||||||
4 | 2 | 15C | CC | 5745 | 5825 | 0.1 | |||||||||||||||||||||||||||||||||||
Line | Rule Parts | Grant Notes | Lower Frequency | Upper Frequency | Power Output | Tolerance | Emission Designator | Microprocessor Number | |||||||||||||||||||||||||||||||||
5 | 1 | 15E | CC | 5180 | 5240 | 0.048417 | |||||||||||||||||||||||||||||||||||
5 | 2 | 15E | CC | 5260 | 5320 | 0.144877 | |||||||||||||||||||||||||||||||||||
Line | Rule Parts | Grant Notes | Lower Frequency | Upper Frequency | Power Output | Tolerance | Emission Designator | Microprocessor Number | |||||||||||||||||||||||||||||||||
6 | 1 | 15C | CC | 2412 | 2462 | 0.128825 | |||||||||||||||||||||||||||||||||||
6 | 2 | 15C | CC | 5745 | 5825 | 0.1 |
some individual PII (Personally Identifiable Information) available on the public forms may be redacted, original source may include additional details
This product uses the FCC Data API but is not endorsed or certified by the FCC