NXR-700/ NXR-800 VHF DIGITAL BASE-REPEATER/ UHF DIGITAL BASE-REPEATER INSTRUCTION MANUAL BASE-RELAIS NUMRIQUE VHF/BASE-RELAIS NUMRIQUE UHF MODE D'EMPLOI BASE-REPETIDOR DIGITAL VHF / BASE-REPETIDOR DIGITAL UHF MANUAL DE INSTRUCCTIONES B62-1994-10 (K) 09 08 07 06 05 04 03 02 01 NXR-700 / NXR-800 INSTRUCTION MANUAL VHF DIGITAL BASE-REPEATER / UHF DIGITAL BASE-REPEATER This repeater is intended for use as a fixed base station with the antenna located outdoors on the rooftop or on an antenna tower. This repeater is designed for a 13.8 V DC power source!
Never use a 24 V DC or higher source to power the repeater. Use only the supplied DC cord. Do not remove the ferrite core attached to the DC cord. Doing so may cause interference with radio communications. UNPACKING AND CHECKING EQUIPMENT Note: The following unpacking information is for use by your Kenwood dealer, an authorized Kenwood service center, or the factory. Carefully unpack the repeater. We recommend that you identify the items listed in the following table before discarding the packing material. If any items are missing or have been damaged during shipment, file a claim with the carrier immediately. Item Front glass Dressed screw Bracket Flat head machine screw Handle and screw set DC cord Lead wire with connector (15 pin) Fuse (7.5 A) Instruction Manual Part Number Quantity B10-2781-XX N08-0563-XX J29-0725-XX N32-4008-XX K01-0421-XX E30-3344-XX E37-1381-XX F05-7521-XX B62-1994-XX 1 1 2 4 1 1 1 1 1 INSTALLATION To install the handles onto the front panel of the repeater, align the handles with the holes on the front panel, then secure the handles using the supplied screws. Please consult your dealer for installing the repeater and antenna. MICROPHONE Connect an optional KMC-30, KMC-35, or KMC-9C Kenwood microphone to the MICROPHONE jack on the front panel. OCXO UNIT (KXK-3):Option The OCXO unit (KXK-3) is an Oven Controlled Crystal Oscillator
(OCXO) unit. THANK YOU!
We are grateful you purchased this Kenwood repeater. We believe this easy-to-program repeater will be highly effective in your communications system, and will keep personnel operating at peak efficiency. Kenwood incorporates the latest in advanced technology into all of our products. As a result, we feel strongly that you will be pleased with the quality and features of this product. PRECAUTIONS Do not expose the unit to rain or moisture; to prevent fire or Do not open the unit under any circumstances; to avoid risk electric shock. of electric shock. Do not expose the unit to long periods of direct sunlight, nor place it close to heating appliances. Do not place the unit in excessively dusty and/or humid areas, nor on unstable surfaces. If you detect an abnormal odor or smoke coming from the unit, disconnect the power from the unit immediately. Contact your Kenwood service center or dealer. NOTICES TO THE USER Government law prohibits the operation of unlicensed radio transmitters within the territories under government control. Illegal operation is punishable by fine and/or imprisonment. Refer service to qualified technicians only. FCC WARNING This equipment generates or uses radio frequency energy. Changes or modifications to this equipment may cause harmful interference unless the modifications are expressly approved in the instruction manual. The user could lose the authority to operate this equipment if an unauthorized change or modification is made. INFORMATION TO THE DIGITAL DEVICE USER REQUIRED BY THE FCC This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can generate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that the interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment to an outlet on a circuit different from that to Consult the dealer for technical assistance. which the receiver is connected. The AMBE+2 voice coding Technology embodied in this product is protected by intellectual property rights including patent rights, copyrights and trade secrets of Digital Voice Systems, Inc. This voice coding Technology is licensed solely for use within this Communications Equipment. The user of this Technology is explicitly prohibited from attempting to extract, remove, decompile, reverse engineer, or disassemble the Object Code, or in any other way convert the Object Code into a human-readable form. U.S. Patent Nos. #5,870,405,
#5,826,222, #5,754,974, #5,701,390, #5,715,365, #5,649,050,
#5,630,011, #5,581,656, #5,517,511, #5,491,772, #5,247,579,
#5,226,084 and #5,195,166.
CONTROLS AND FUNCTIONS Front Panel q w e r t y u STATUS 3 4 5 6 7 8 1 2 CTRL OCXO BUSY TX POWER MON TAKE OVER RPT DISABLE A B C VOLUME COM OFF/
MICROPHONE
!0!1!2 io q Speaker w CH/STATUS Display Two 17-segment digits display the channel number, name, or status. e STATUS indicator Indicates the status of the repeater. (NXDN mode) r Programmable Function keys Press these keys to activate their programmable functions. t COM jack Connect to the PC using a RS-232C standard DB9
(Female) cross cable. y VOLUME control Turn clockwise until a click sounds, to unmute the audio. Rotate to adjust the audio. Turn counterclockwise fully to mute the audio. u MICROPHONE jack Connect a microphone to this 8-pin modular jack. i POWER indicator Lights green when power is supplied to the DC 13.8V jack. Blinks red when an abnormal voltage is present. While blinking, the repeater cannot be used. o TX indicator Lights red while transmitting.
!0 BUSY indicator Lights green while a signal is being received.
!1 OCXO indicator The OCXO indicator shows the state of the reference 10 MHz oscillator :
Lights Green when using a reference signal from an optional OCXO unit (KXK-3). Lights Orange when using a reference signal from another repeater. Lights red when no reference signal is available or when an error occurs. Does not light when the reference signal is an internal VCXO signal.
!2 CTRL indicator The CTRL indicator shows the control channel status while using Digital trunking :
Lights Green when the repeater is used as control channel. Blinks Green when using a non-dedicated control channel. Rear Panel w TEST/SPKR q RX e r t y u CONTROL I/O SYNC 2 1 LAN REF OUT REF IN o DC 13.8V i FUSE 7 5 TX q RX IN jack Connect an RX antenna or a duplexer to this BNC receptacle. w TEST/SPKR jack Test input/output jack. Connect an external speaker to this jack. e CONTROL I/O jack Connect a repeater controller or a remote panel to this DB-25 interface. r SYNC 1 / 2 jack Connect to another repeater to use synchronous frame signaling for digital trunking. t LAN jack Connect to Ethernet. REPEATER OPERATION Note: Please consult your dealer for programming the repeater. Due to the frequency stability on the 6.25 kHz bandwidth channel, when operating the repeater using an optional OCXO unit, allow the unit to warm up for 24 hours after turning the power on. After turning on the power, wait for approximately 10 seconds for the VCXO or 5 minutes for the OCXO (when mounting) to warm up. During this time, the CH/STATUS Display will blink. The keys will function when they are pressed. When power is applied to the unit, the POWER indicator lights green. Turn the VOLUME control clockwise until a click sounds, to unmute the audio. Rotate to adjust the audio. Turn the VOLUME control counterclockwise fully to mute the audio. The BUSY indicator lights green while receiving a signal and the TX indicator lights red while transmitting.
y REF OUT jack Connect to another repeater within the site to supply a reference signal. Connect from another repeater within the site to receive a reference signal. Insert 7.5 A blade fuse into this fuse holder. Connect a 13.8 V DC power supply to this jack. u REF IN jack i FUSE o DC 13.8V jack TX OUT jack Connect a TX antenna or a duplexer to this BNC receptacle. TRANSCEIVER OPERATION Receive Adjust the volume to your desired level. You may need to readjust the volume if you are having interference while receiving a message from your dispatcher or another member in your fleet. The BUSY indicator lights green while a signal is being received. Transmit 1 Listen to the channel before transmitting, to make sure it is not being used. 2 Press the microphone PTT switch, then speak in your normal speaking voice. The TX indicator lights red while transmitting. 3 When you finish speaking, release the PTT switch. MODE DEMPLOI DU NXR-700 / NXR-800 BASE-RELAIS NUMRIQUE VHF / BASE-RELAIS NUMRIQUE UHF MERCI !
Nous sommes trs heureux que vous ayez achet ce rpteur Kenwood. Nous pensons que ce rpteur facile programmer sera extrmement ef cace dans votre systme de communications et restera optimal pour un fonctionnement personnel. Kenwood intgre la dernire technologie avance dans tous nos produits. Par consquent, nous avons la nette impression que vous serez satisfait de la qualit et des caractristiques de ce produit. PRECAUTIONS
Nexposez pas lunit la pluie ou lhumidit pour viter tout risque dincendie ou de choc lectrique.
Nouvrez lunit sous aucun prtexte a n dviter tout risque de choc lectrique.
Nexposez pas lunit aux rayons directs du soleil pendant des priodes prolonges, ne le posez pas non plus proximit dappareils de chauffage.
Ne posez pas lunit dans des endroits extrmement poussireux et/ou humides, ni sur des surfaces instables.
Si vous dtectez une odeur anormale ou une fume provenant de lunit, dbranchez lunit immdiatement. Contactez votre centre de service ou revendeur Kenwood. REMARQUES DESTINEES A L'UTILISATEUR La loi gouvernementale interdit lutilisation dmetteurs-rcepteurs radio non autoriss sur les territoires sous contrle gouvernemental. Une utilisation illgale est punissable dune amende et/ou dune peine demprisonnement. Con ez lentretien uniquement des techniciens quali s. La technologie de codage vocal AMBE+2 contenue dans ce produit est protge par les droits de proprit intellectuelle, qui incluent les droits de brevets, les droits dauteur et secrets industriels de Digital Voice systems, Inc. Cette technologie de codage vocal est une licence accorde uniquement pour une utilisation lintrieur de cet quipement de communications. Lutilisateur de cette technologie linterdiction explicite de tenter dextraire, de supprimer, dcompiler, faire de lingnierie inverse ou dmonter le code objet, ou de quelque manire que ce soit de convertir le code objet en une forme lisible par lhomme. N de brevets amricains. #5,870,405, #5,826,222, #5,754,974, #5,701,390,
#5,715,365, #5,649,050, #5,630,011, #5,581,656, #5,517,511,
#5,491,772, #5,247,579, #5,226,084 et #5,195,166. ATTENTION Ce rpteur est conu pour une utilisation en tant que station de base xe avec lantenne situe lextrieur sur le toit ou un pylne dantenne. Ce rpteur est conu pour une source dalimentation de 13,8 Vcc !
Nutilisez jamais une source dalimentation de 24 Vcc ou suprieure pour alimenter le rpteur. Utilisez uniquement le cble CC fourni. Nenlevez pas le noyau magntique x au cble CC. Dans le cas contraire, cela peut entraner des interfrences avec les communications radio. DEBALLAGE ET VERIFICATION DE LEQUIPEMENT Remarque :
Les informations suivantes relatives au dballage doivent tre utilises par votre revendeur Kenwood, un centre de service agr Kenwood ou lusine. Dballez le rpteur avec soin. Nous vous recommandons didenti er les articles numrs dans le tableau suivant avant de jeter lemballage. Si un article est manquant ou a t endommag pendant le transport, remplissez immdiatement un formulaire de plainte avec le transporteur. Numro de pice Quantit Article Glace avant Vis pare Fixation Vis mtaux tte plate Manche et ensemble de vis Cble CC Fil avec connecteur (15 broches) Fusible (7,5 A) Mode demploi B10-2781-XX N08-0563-XX J29-0725-XX N32-4008-XX K01-0421-XX E30-3344-XX E37-1381-XX F05-7521-XX B62-1994-XX 1 1 2 4 1 1 1 1 1 INSTALLATION Pour installer les poignes sur le panneau avant du rpteur, alignez les poignes aux ori ces sur le panneau avant, ensuite, xez les poignes laide des vis fournies. Veuillez contacter votre revendeur pour linstallation du rpteur et de lantenne. MICROPHONE Connectez un microphone KMC-30, KMC-35 ou KMC-9C Kenwood en option la prise MICROPHONE du panneau avant. UNITE OCXO (KXK-3) : Option Lunit OCXO (KXK-3) est un Oscillateur quartz thermostat (OCXO). F-1 B62-1994-00_NXR-700-800.indd Sec2:1 B62-1994-00_NXR-700-800.indd Sec2:1 2008/02/12 15:20:09 2008/02/12 15:20:09 COMMANDES ET FONCTIONS Panneau avant a b c d e f g STATUS 3 4 5 6 7 8 1 2 VOLUME CTRL OCXO BUSY TX POWER MON TAKE OVER RPT DISABLE A B C COM OFF/
MICROPHONE jkl hi a Haut-parleur b Af cheur CH/STATUS Deux chiffres 17 segments af chent le numro du canal, son nom ou son tat. c Indicateur STATUS Indique ltat du rpteur. (mode NXDN) d Touches fonctions programmables Appuyez sur ces touches pour activer leurs fonctions programmables. e Prise COM Connectez au PC laide dun cble crois RS-232C standard DB9 (femelle). f Commande VOLUME Tournez dans le sens des aiguilles dune montre jusqu entendre un clic, pour dsactiver la sourdine du niveau sonore. Tournez pour rgler le niveau sonore. Tournez compltement dans le sens contraire des aiguilles dune montre pour mettre le niveau sonore en sourdine. g Prise MICROPHONE Connectez un microphone cette prise modulaire 8 broches. h Indicateur POWER Le tmoin vert sallume lorsque la prise 13,8 Vcc est alimente. Le tmoin rouge clignote lorsquune tension anormale est prsente. Lorsquil clignote, le rpteur ne peut pas tre utilis. i Indicateur TX Le tmoin rouge sallume lors de la transmission. j Indicateur BUSY Le tmoin vert sallume alors quun signal est reu. k Indicateur OCXO Lindicateur OCXO af che ltat de loscillateur 10 MHz de rfrence :
Le tmoin vert sallume lors de lutilisation dun signal de rfrence dune unit OCXO en option (KXK-3). Le tmoin orange sallume lors de lutilisation dun signal de rfrence dun autre rpteur. Le tmoin rouge sallume lorsquaucun signal de rfrence nest disponible ou lorsquune erreur survient. Ne sallume pas lorsque le signal de rfrence est un signal VCXO interne. l Indicateur CTRL Lindicateur CTRL af che ltat du canal de contrle lors de lutilisation de liaison numrique :
Le tmoin vert sallume lorsque le rpteur est utilis comme canal de contrle. Le tmoin vert clignote lors de lutilisation dun canal de contrle non-spci . Panneau arrire b TEST/SPKR a RX c d e f g h i CONTROL I/O SYNC 2 1 LAN REF OUT REF IN FUSE DC 13.8V 7 5 j TX a Prise RX IN Raccordez une antenne RX ou un duplexeur ce rceptacle BNC. b Prise TEST/SPKR Testez la prise dentre/sortie. Raccordez un haut-parleur externe cette prise. c Prise CONTROL I/O Raccordez un contrleur de rpteur ou un panneau distant cette interface DB-25. d Prise SYNC 1 / 2 Raccordez un autre rpteur pour utiliser une signalisation de cadre synchrone pour une liaison numrique. e Prise LAN Raccordez Ethernet. Veuillez contacter votre revendeur en ce qui concerne la FONCTIONNEMENT DU REPETEUR Remarque :
programmation du rpteur. En raison de la stabilit de frquence sur le canal bande passante 6,25 kHz, lorsque vous utilisez le rpteur laide dune unit OCXO en option, laissez lunit prchauffer pendant 24 heures aprs la mise sous tension. Aprs la mise sous tension, attendez environ 10 secondes pour le VCXO ou 5 minutes pour le OCXO (lors du montage) pour le prchauffage. Pendant ce temps, laf cheur CH/STATUS clignote. Les touches fonctionneront chaque pression. Lorsque lunit est mise sous tension, lindicateur vert POWER sallume. Tournez la commande VOLUME dans le sens des aiguilles dune montre jusqu entendre un clic, pour dsactiver la sourdine du niveau sonore. Tournez pour rgler le niveau sonore. Tournez compltement la commande VOLUME dans le sens contraire des aiguilles dune montre pour mettre le niveau sonore en sourdine. Lindicateur vert BUSY sallume lors de la rception dun signal et lindicateur rouge TX sallume lors de la transmission. f Prise REF OUT Raccordez un autre rpteur sur le site pour fournir un signal de rfrence. g Prise REF IN Raccordez depuis un autre rpteur sur le site pour recevoir un signal de rfrence. h FUSIBLE Insrez un fusible de 7,5 A dans ce porte-fusible. i Prise 13,8Vcc Connectez une alimentation de 13,8 Vcc cette prise. j Prise TX OUT Raccordez une antenne TX ou un duplexeur ce rceptacle BNC. FONCTIONNEMENT DE LEMETTEUR-
RECEPTEUR Rception Rglez le volume au niveau souhait. Il se peut que vous deviez rgler nouveau le volume si des interfrences surviennent lors de la rception dun message de votre rpartiteur ou dun autre membre de votre groupe. Lindicateur vert BUSY sallume lors de la rception dun signal. Transmission 1 Ecoutez le canal avant la transmission a n de vous assurer quil nest pas utilis. 2 Appuyez sur le commutateur PTT du microphone, ensuite parlez sans changer votre voix. Lindicateur rouge TX sallume lors de la transmission. 3 Lorsque vous avez ni de parler, relchez le commutateur PTT. F-2 B62-1994-00_NXR-700-800.indd Sec2:2 B62-1994-00_NXR-700-800.indd Sec2:2 2008/02/12 15:20:10 2008/02/12 15:20:10 MANUAL DE INSTRUCCIONES DEL NXR-700 / NXR-800 BASE-REPETIDOR DIGITAL VHF / BASE-REPETIDOR DIGITAL UHF MUCHAS GRACIAS Gracias por comprar este repetidos de Kenwood. Creemos que este repetidor de fcil programacin ser altamente efectivo en su sistema de comunicaciones para que su personal trabaje con la mayor e cacia posible. Kenwood incorpora lo ltimo en tecnologa avanzada en todos nuestros productos. Estamos seguros de que usted quedar plenamente satisfecho de la calidad y las caractersticas de este producto. PRECAUCIONES
Para evitar incendios o descargas elctricas, no exponga la unidad a la lluvia o a la humedad.
Para evitar riesgos de descarga elctrica, no abra la unidad en ningn momento.
No exponga la unidad a la luz directa del sol, ni la coloque cerca de calefactores.
No coloque la unidad en zonas excesivamente polvorientas o hmedas, ni sobre super cies inestables.
Si detecta un olor o humo anormal proveniente de la unidad, desconecte la alimentacin inmediatamente y pngase en contacto con el servicio tcnico de Kenwood o con su proveedor. AVISOS AL USUARIO La ley gubernamental prohbe el uso de radiotransmisores no autorizados dentro de los territorios que se encuentren bajo el control del gobierno. El uso ilegal se castigar con multa y/o encarcelamiento. Solicite la reparacin solamente a un tcnico cuali cado. La tecnologa de compresin de voz AMBE+2 que se incorpora en este producto est protegida por derechos de propiedad intelectual, que abarcan los derechos de patente, derechos de copyright y secretos comerciales de Digital Voice Systems, Inc. Dicha tecnologa de compresin de voz se ofrece bajo licencia nica y exclusivamente para su uso en este equipo de comunicaciones. Quedando categricamente prohibido cualquier intento de extraccin, descompilacin, ingeniera inversa o desmontaje del cdigo objeto por parte del usuario de esta tecnologa, as como cualquier intento de conversin del Cdigo objeto a formato legible por el hombre. Nmeros de patente EE.UU. N 5,870,405, N 5,826,222, N 5,754,974, N 5,701,390, N 5,715,365, N 5,649,050, N 5,630,011, N 5,581,656, N 5,517,511, N 5,491,772, N 5,247,579, N 5,226,084 y N 5,195,166. PRECAAUCIN Este repetidor est pensado para utilizarse como estacin base ja con la antena situada en exteriores, ya sea en el tejado o en una torreta de antena. El repetidor est diseado para una fuente de alimentacin de 13,8 V CC. No utilice una fuente 24 V CC o mayor para alimentar el repetidor. Utilice nicamente el cable CC suministrado. No extraiga el ncleo de ferrita acoplado al cable de CC. De hacerlo, podra causar interferencias con las comunicaciones por radio. DESEMBALAJE Y COMPROBACIN DEL EQUIPO Nota : La informacin sobre desembalaje que se ofrece a continuacin est destinada a su distribuidor Kenwood, a un servicio tcnico autorizado de Kenwood o a la fbrica. Desembale el repetidor con cuidado. Recomendamos que antes de tirar el material de embalaje, identi que los elementos indicados en la tabla siguiente. Si falta algo o se ha producido algn dao durante el transporte, presente inmediatamente una reclamacin a la empresa de transporte. Artculo Nmero de pieza Cantidad Cristal frontal Tornillo Soporte Tornillo mecnico plano Asa y juego de tornillos Cable CC Cable conductor con conector (15 patillas) Fusible (7,5 A) Manual de instrucciones B10-2781-XX N08-0563-XX J29-0725-XX N32-4008-XX K01-0421-XX E30-3344-XX E37-1381-XX F05-7521-XX B62-1994-XX 1 1 2 4 1 1 1 1 1 INSTALACIN Para montar las asas en el panel frontal del repetidor, alinelas con los agujeros situados en el panel frontal y, a continuacin, je las asas utilizando los tornillos suministrados. Para obtener informacin sobre la instalacin del repetidor y de la antena, consulte a su distribuidor. MICRFONO Conecte un micrfono Kenwood KMC-30, KMC-35 o KMC-9C opcional al jack MICROPHONE del panel frontal. UNIDAD OCXO (KXK-3): opcional La unidad OCXO (KXK-3) es un oscilador de cristal de cuarzo termostatazo (OCXO Oven Controlled Crystal Oscillator). E-1 B62-1994-00_NXR-700-800.indd Sec3:1 B62-1994-00_NXR-700-800.indd Sec3:1 2008/02/12 15:20:10 2008/02/12 15:20:10 CONTROLES Y FUNCIONES Panel frontal a b c d e f g STATUS 3 4 5 6 7 8 1 2 VOLUME CTRL OCXO BUSY TX POWER MON TAKE OVER RPT DISABLE A B C COM OFF/
MICROPHONE jkl hi a Altavoz b Pantalla CH/STATUS Dos dgitos de 17 segmentos indican el nmero, el nombre o el estado del canal. c Indicador STATUS Indica el estado del repetidor. (Modo NXDN) d Teclas de funcin programables Plselas para activar sus funciones programables. e Jack COM Conexin al PC mediante un cable cruzado DB9 (hembra) estndar RS-232C. f Control VOLUME Grelo hacia la derecha hasta que oiga un chasquido para desactivar el silenciamiento. Grelo para ajustar el nivel de audio. Grelo completamente hacia la izquierda para activar el silenciamiento. g Jack MICROPHONE Conecte un micrfono a este jack modular de 8 patillas. h Indicador POWER Se ilumina de color verde cuando se suministra alimentacin elctrica al jack 13,8 V CC. Parpadea de color rojo cuando el nivel de tensin es anormal. Mientras parpadea, no se puede utilizar el repetidor. i Indicador TX Se ilumina de color rojo durante la transmisin. j Indicador BUSY Se ilumina de color verde mientras se est recibiendo una seal. k Indicador OCXO El indicador OCXO muestra el estado del oscilador de 10 MHz de referencia. Se ilumina de color verde cuando se utiliza una seal de referencia de una unidad OCXO opcional (KXK-3). Se ilumina de color naranja cuando se utiliza una seal de referencia de otro repetidor. Se ilumina de color rojo cuando no hay presencia de ninguna seal de referencia o cuando se produce un error. No se ilumina cuando la seal de referencia es una seal VCXO interna. l Indicador CTRL El indicador CTRL muestra el estado del canal de control cuando se utiliza trunking digital. Se ilumina de color verde cuando el repetidor se utiliza como canal de control. Parpadea de color verde cuando se utiliza un canal de control no dedicado. Panel trasero b TEST/SPKR a RX c d e f g h i CONTROL I/O SYNC 2 1 LAN REF OUT REF IN FUSE DC 13.8V 7 5 j TX a Jack RX IN Conecte una antena RX o un duplexador a esta toma BNC. b Jack TEST/SPKR Compruebe el jack de entrada/salida. Conecte un altavoz externo a este jack. c Jack CONTROL I/O Conecte un controlador de repetidor o un panel remoto a esta interfaz DB-25. d Jack SYNC 1 / 2 Conexin a otro repetidor para utilizar seales de tramas sincrnicas o trunking digital. e Jack LAN Conexin a Ethernet. f Jack REF OUT Conexin a otro repetidor dentro del emplazamiento para proveer una seal de referencia. g Jack REF IN Conexin de otro repetidor dentro del emplazamiento para proveer una seal de referencia. h FUSE Inserte un fusible de pala de 7,5 A en este portafusibles. i Jack 13,8 V CC Conecte una fuente de alimentacin 13,8 V CC a este jack. j Jack TX OUT Conecte una antena TX o un duplexador a esta toma BNC. FUNCIONAMIENTO DEL REPETIDOR Nota : Consulte a su distribuidor para conocer cmo se programa el repetidor. Debido a la estabilidad de frecuencia en el canal de ancho de banda de 6,25 MHz, cuando utilice el repetidor con una unidad OCXO opcional, deje calentar la unidad durante 24 horas una vez encendida. Cuando conecte la alimentacin, espere unos 10 segundos en el caso del VCXO o 5 minutos en el caso del OCXO (al montarlo) para que se caliente. La indicacin CH/STATUS parpadear durante dicho tiempo. Las teclas funcionarn cuando se pulsen. Cuando se suministra alimentacin elctrica, el indicador POWER se ilumina de color verde. Gire el control VOLUME hacia la derecha hasta que oiga un chasquido para desactivar el silenciamiento. Grelo para ajustar el nivel de audio. Grelo completamente hacia la izquierda para activar el silenciamiento. El indicador BUSY se ilumina de color verde mientras se recibe una seal, y el indicador TX se ilumina de color rojo durante la transmisin. FUNCIONAMIENTO DEL TRANSCEPTOR Recepcin Ajuste el volumen al nivel deseado. Quizs tenga que volver a ajustarlo si se producen interferencias durante la recepcin de un mensaje procedente de su distribuidor de mensajes o de otro miembro de la ota. El indicador BUSY se ilumina de color verde durante la recepcin de una seal. Transmisin 1 Escuche el canal antes de transmitir, para asegurarse de que no est en uso. 2 Presione el conmutador PTT del micrfono y hable con su tono de voz habitual. El indicador TX se ilumina de color rojo durante la transmisin. 3 Cuando termine de hablar, suelte el conmutador PTT. E-2 B62-1994-00_NXR-700-800.indd Sec3:2 B62-1994-00_NXR-700-800.indd Sec3:2 2008/02/12 15:20:10 2008/02/12 15:20:10 TERMINAL MIC(Modular Jack) Pin Number Pin Name 1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8 9 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 NC SB GND PTT MICG MIC HOOK NC CD RD SD DTR SG DSR RTS CTS CI SB SB NC GND GND SPG RD RSSI SPI AO1 AO2 SPO AO3 AO4 AO5 Description Specification I/O notes Power Output GND PTT Signal MIC GND MIC Input Hook Detection 13.8V GND MIC GND 600 Input Impeadance 100k Input Impeadance 100k I I I I/O I I O O I O I I notes COM (D-SUB 9Pin) CONNECTOR Pin Number Pin Name Description Carrier Detect Receive Data Send Data Data Terminal Ready GND Data Set Ready Request to Send Clear to Send Ringer DET Specification Conform to RS-232C standard Conform to RS-232C standard Conform to RS-232C standard Conform to RS-232C standard GND Conform to RS-232C standard Conform to RS-232C standard Conform to RS-232C standard Conform to RS-232C standard TEST/SPEAKER CONNECTOR Pin Number Pin Name Description Power Output Power Output Specification 13.8V 13.8V I/O notes GND GND Speaker GND RX Audio Output RSSI Signal Output Internal Speaker Input Open Collector Terminal Open Collector Terminal External Speaker Output Open Collector Terminal Open Collector Terminal Open Collector Terminal GND GND Speaker GND Short with "SPO"
Load impedance 4.7k Output Level 0 to 5V O O I Allowable current value MAX 200mA O Allowable current value MAX 200mA O O Allowable current value MAX 200mA O Allowable current value MAX 200mA O Allowable current value MAX 200mA O Output Level 3W (5% Distortion) not De-emphasis Control I/O (D-SUB 25Pin) CONNECTOR Pin Number Pin Name Description BER CLK EMON EPTT SC BER DAT NC NC NC AI1 AI2 AI3 DG TD TA RD RA RXG SPM TXG IO1 IO2 IO3 IO4 IO5 IO6 TD+
TD-
RD+
NC NC RD-
NC NC NC NC 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 1 2 3 4 5 6 7 8 1 2 3 4 LAN(Modular Jack) Pin Number Pin Name Programmable Function Input 1 Programmable Function Input 2 Programmable Function Input 3 Digital GND TX Audio Input TX Audio Input RX Audio Output RX Audio Output RX Signal GND Speaker Mute For Bit Error Rate Clock External Monitor Switch External PTT Switch Squelch Control For Bit Error Rate Data TX Signal GND Programmable Function I/O 1 Programmable Function I/O 2 Programmable Function I/O 3 Programmable Function I/O 4 Programmable Function I/O 5 Programmable Function I/O 6 Specification I/O notes Input Impeadance 47k Input Impeadance 47k Input Impeadance 47k Input Impeadance 600 Input Impeadance 600 Load impedance 4.7k Load impedance 4.7k Input Impeadance 47k CMOS Input Impeadance 47k Input Impeadance 47k Output Level 0 or 3.3V CMOS not Pre-emphasis Pre-emphasis not De-emphasis De-emphasis I I I I I O O I O I I O O Input Impeadance 47k Input Impeadance 47k Input Impeadance 47k Input Impeadance 47k Input Impeadance 47k Input Impeadance 47k I/O Output Level 0 to 5V I/O Output Level 0 to 5V I/O Output Level 0 to 5V I/O Output Level 0 to 5V I/O Output Level 0 to 5V I/O Output Level 0 to 5V Description TX Signal+
TX Signal-
RX Signal+
Specification Conform to IEEE802.3 standard Conform to IEEE802.3 standard Use Designated Transformer RX Signal-
Use Designated Transformer notes 100Mbps 100Mbps 100Mbps 100Mbps notes I/O O O I I I/O I/O I/O SYNC1, 2 Connector (There are two connectors) Pin Number Pin Name Description FRMA RS-458 Diffrential Signal A Specification Conform to RS485 FRMB RS-458 Diffrential Signal B Conform to RS485 RX ANT TX ANT REF IN REF OUT Impeadance 50 Impeadance 50 External Reference Signal Input(10MHz). Impedance : more than 1kohm Reference Signal Distribution(10MHz). Load impedance more than 20ohm. MANDATORY SAFETY INSTRUCTIONS TO INSTALLERS AND USERS Use only manufacturer or dealer supplied antenna. Antenna Minimum Safe Distance: 60 cm (2 feet), 50% duty Cycle. Antenna Gain: 0 dBd referenced to a dipole. The Federal Communications Commission has adopted a safety standard for human exposure to RF (Radio Frequency) energy which is below the OSHA (Occupational Safety and Health Act) limits. Antenna Mounting: The antenna supplied by the manufacturer or radio dealer must not be mounted at a location such that during radio transmission, any person or persons can come closer than the above indicated minimum safe distance to the antenna, i.e. 60 cm (2 feet) , 50% duty Cycle. To comply with current FCC RF Exposure limits, the antenna must be installed at or exceeding the minimum safe distance shown above, and in accordance with the requirements of the antenna manufacturer or supplier. Vehicle installation: The antenna can be mounted at the center of a vehicle metal roof or trunk lid, if the minimum safe distance is observed. Base Station Installation: The antenna should be fixed-mounted on an outdoor permanent structure. RF Exposure compliance must be addressed at the time of installation. Antenna substitution: Do not substitute any antenna for the one supplied or recommended by the manufacturer or radio dealer. You may be exposing person or persons to excess radio frequency radiation. You may contact your radio dealer or the manufacturer for further instructions. Maintain a separation distance from the antenna to person(s) of at least 60 cm (2 feet) , 50% duty Cycle. You, as the qualified end-user of this radio device must control the exposure conditions of bystanders to ensure the minimum separation distance (above) is maintained between the antenna and nearby persons for satisfying RF Exposure compliance. The operation of this transmitter must satisfy the requirements of Occupational/Controlled Exposure Environment, for work-related use, transmit only when person(s) are at least the minimum distance from the properly installed, externally mounted antenna. Transmit only when people outside the vehicle are at least the recommended minimum lateral distance away from the antenna/vehicle