WARNING:pdfminer.pdfpage:The PDF <_io.BufferedReader name='/Volumes/Scratch/Incoming/eg-scratch/6532189.pdf'> contains a metadata field indicating that it should not allow text extraction. Ignoring this field and proceeding. Use the check_extractable if you want to raise an error in this case NXR-1700 NXR-1800 INSTRUCTION MANUAL MODE DEMPLOI MANUAL DE INSTRUCCIONES MANUALE DI ISTRUZIONI BEDIENUNGSANLEITUNG GEBRUIKSAANWIJZING KULLANIM KILAVUZU
MANUAL DO UTILIZADOR B5A-3612-10
NXR-1700/ NXR-1800
THANK YOU!
We are grateful you purchased this KENWOOD repeater. PRECAUTIONS Do not expose the repeater to rain or moisture in order to prevent
Do not open the repeater under any circumstances in order to
Do not expose the repeater to long periods of direct sunlight, nor place it close to heating appliances. Do not place the repeater in excessively dusty and/or humid areas, nor on unstable surfaces.
in a place which can be reached by a small child's hands. It will
KENWOOD.
repeater, disconnect the power from the repeater immediately, and contact your KENWOOD service center or dealer.
the front of the main body or the fan at the rear. NOTICES TO THE USER
product is protected by intellectual property rights including patent rights, copyrights and trade secrets of Digital Voice Systems, Inc. This voice coding Technology is licensed solely
Technology is explicitly prohibited from attempting to extract, remove, decompile, reverse engineer, or disassemble the Object Code, or in any other way convert the Object Code into a human-readable form. U.S. Patent Nos. #7,970,606, #8,359,197,
#8,315,860, and #8,595,002. Firmware Copyrights
Corporation. UNPACKING AND CHECKING EQUIPMENT Note: KENWOOD dealer, an authorized KENWOOD service center, or the factory.
material. If any items are missing or have been damaged during
Item Remarks Quantity
4 m (with fuse box) Government law prohibits the operation of unlicensed radio transmitters within the territories under government control.
WARNING Do not install the repeater in an explosive atmosphere (of
powders, etc.).
Reinforcing hardware
Instruction manual Short type
1 1 1 4 1 8 1 4 1 CAUTION
the antenna located outdoors on the rooftop or on an antenna tower. This repeater is designed for a 13.2 V DC power source. Never use a 24 V DC or higher source to power the repeater. Use only the supplied DC power cable. Do not remove the ferrite core connected to the DC power cable. Removal may cause harmful interference with radio communications. Do not put anything on top of the repeater. Putting something on top obstructs heat dissipation.
During transmission, do not touch the antenna terminals or the
Do not touch the metal surface of the repeater during use.
Continuous listening to loud sounds can cause hearing
Use only the supplied DC power cable or a KENWOOD optional DC power cable. Do not cut and/or remove the fuse holder on the DC power cable. Note: Use only the supplied screws. INSTALLATION Refer to the diagrams below when mounting the repeater on the
jointly mounted by using the attached reinforcing hardware.
Consult your dealer for further detail of installing the repeater and antenna. Bracket : Short type Reinforcing hardware
(Used when installing two repeaters.) 1 Bracket : Long type
(Used when installing one repeater.) CONTROLS AND FUNCTIONS Front Rear TX CONTROL I/O RX Display
repeater. POWER indicator
on.
RX1 and RX2 are lit while receiving a signal with matching signaling and only RX1 is lit while receiving a signal that does not match signaling. STATUS indicator
is abnormal. Ventilation slots Fan DC jack
Note:
TX OUT jack Connect a TX antenna or a duplexer to this N receptacle. CONTROL I/O jack Connect a repeater controller or a remote panel to this
RX IN jack
REPEATER OPERATION Note: Please consult your dealer for programming the repeater. The RX1/ RX2 indicator lights green while receiving a signal and the TX1/ TX2 indicator lights red while transmitting. POWER switch/selector TRANSCEIVER OPERATION Note: your dealer for other methods for transmission and reception by
Receive
may need to readjust the volume if you are having interference while receiving a message from your dispatcher or another
RX1/ RX2 indicator lights green while a signal is being received. Transmit 1 being used. 2 Change the Test PTT Control
TX1/ TX2 indicator lights red while transmitting. 3 Test PTT Control to
The following two methods using the KPG-D7 settings turn the
When DC power is supplied to the repeater, the power is automatically turned on. When power is no longer
LAN jack
USB port (Type-A)
audio driver. TX1/ TX2 indicator During DMR transmission, the TX1 indicator lights red when communicating with the radio in Timeslot 1, and the TX2 indicator lights red when communicating with the radio in Timeslot 2.
TX1 and TX2 are lit during transmission.
RX1/ RX2 indicator On the DMR standby channel, the RX1 indicator lights green while receiving a receivable CC matching signal in Timeslot 1. The RX2 indicator lights green while receiving a receivable CC matching signal in Timeslot 2. 2 CONSIGNES DE SCURIT OBLIGATOIRES DESTINES AUX INSTALLATEURS ET AUX UTILISATEURS
Reportez-
vous aux valeurs indiques dans le tableau ci-dessous.
0
AVERTISSEMENT
Distance minimum de scurit par rapport l'antenne Gamme de frquences NXR-1700-E Puissance nominale Distance de scurit
NXR-1800-E2
FCC WARNING This equipment generates or uses radio frequency energy. Changes or
INFORMATION TO THE DIGITAL DEVICE USER REQUIRED BY THE FCC
SUPPLIER'S DECLARATION OF CONFORMITY
MANDATORY SAFETY INSTRUCTIONS TO INSTALLERS AND USERS
Refer to the values in the table below.
0
instructions. WARNING
Antenna Minimum Safe Distance Frequency Range Rated Power Safe Distance NXR-1700-E NXR-1800-E2
2023