TRANSCEPTOR Serie NX-5000 Serie NX-3000 Serie NX-1000 GUA DEL USUARIO ADVERTENCIA PRECAUCIN de KENWOOD. atrapar el cable. Para la seguridad de los pasajeros, instale el transceptor de forma segura utilizando el soporte de montaje suministrado u opcional y el juego de tornillos de forma que el transceptor no se suelte en caso de colisin. El transceptor slo funciona en sistemas de 12 V con negativo a tierra! Compruebe la polaridad y el voltaje de la batera del vehculo antes de instalar el transceptor. Utilice nicamente el cable de alimentacin CC suministrado o un cable de alimentacin CC opcional No corte ni extraiga el porta fusible del cable de alimentacin CC. No le el cable del micrfono alrededor del cuello cuando est cerca de mquinas que pudieran Al sustituir el fusible del cable de alimentacin de CC, asegrese de sustituirlo por otro con la misma capacidad. No sustituya nunca un fusible por otro que posea una capacidad superior. No toque la superficie metlica del transceptor mientras est en uso. Tampoco monte el transceptor de manera que el chasis pueda ponerse en contacto con la piel. Las temperaturas altas podran causar quemaduras. MANDATORY SAFETY INSTRUCTIONS TO INSTALLERS AND USERS Use only manufacturer or dealer supplied antenna. Antenna Minimum Safe Distance: Refer to the values in the table below. Antenna Gain: 0 dBd referenced to a dipole. The Federal Communications Commission has adopted a safety standard for human exposure to RF (Radio Frequency) energy which is below the OSHA (Occupational Safety and Health Act) limits. Antenna Mounting: The antenna supplied by the manufacturer or radio dealer must not be mounted at a location such that during radio transmission, any person or persons can come closer than the minimum safe distance indicated in the table below. To comply with current FCC/ ISED RF Exposure limits, the antenna must be installed at or exceeding the minimum safe distance shown above, and in accordance with the requirements of the antenna manufacturer or supplier. Vehicle installation: The antenna can be mounted at the center of a vehicle metal roof or trunk lid, if the minimum safe distance is observed. Base Station Installation: The antenna should be fixed-mounted on an outdoor permanent structure. RF Exposure compliance must be addressed at the time of installation. SUPERFICIE CALIENTE Antenna substitution: Do not substitute any antenna for the one supplied or recommended by the manufacturer or radio dealer. You may be exposing person or persons to excess radio frequency radiation. You may contact your radio dealer or the manufacturer for further instructions. JVCKENWOOD Corporation estar exenta de cualesquiera responsabilidades por las prdidas o daos incidentales como, por ejemplo, falta de comunicaciones u oportunidades de comunicacin causadas por un fallo o error de rendimiento del transceptor. WARNING Este Gua del usuario slo cubre las operaciones bsicas de su radio. Para ver el Manual de instrucciones de detalles, consulte el siguiente URL o cdigo QR. https://manual.kenwood.com/files/B5K-0995-00.pdf La tecnologa de codificacin de voz AMBE+2 integrada en este producto est protegida por derechos de propiedad intelectual incluyendo los derechos de patente, los derechos de autor y secretos comerciales de Digital Voice Systems, Inc. Esta tecnologa de codificacin de voz otorga licencia para su uso nicamente dentro de este equipo de comunicaciones. Est explcitamente prohibido que el usuario de esta tecnologa intente extraer, retirar, descompilar, realizer ingeniera inversa, o desmontar el cdigo objeto, o convertir de cualquier otra manera el cdigo objeto a una forma legible para el ser humano. Los nmeros de patente de los EE.UU. #7,970,606,
#8,359,197, #8,315,860 y #8,595,002. Derechos de autor del firmware El ttulo y la propiedad de los derechos de autor del firmware incorporado en memorias de productos KENWOOD estn reservados para JVCKENWOOD Corporation. AVISOS AL USUARIO ACCESORIOS SUMINISTRADOS Desembale el transceptor con cuidado. Le recomendamos que logre identificar los elementos que se indican a continuacin antes de deshacerse del material de embalaje. Si falta o ha resultado daado algn artculo durante el envo, presente inmediatamente una reclamacin a la empresa de transporte. Artculo Serie NX-5000 NX-5xxx NX-5xxxB NX-5xxxHB Cable de alimentacin CC con fusibles (15 A) Soporte de montaje Micrfono Horquilla del micrfono Tornillo autorroscantes de 4 x 16 mm) Juego de tornillos:
Tornillo autorroscante de 5 x 16 mm Tornillo de cabeza hexagonal con arandela de M4 x 6 mm Arandela de resorte Arandela plana Enchufe Funda de moldura Tornillo de cabeza sems de M4 x 10 mm Gua del usuario 1 1 1 1 3 4 4 4 4 1 1 Serie NX-3000 1 1 1 1 3 Serie NX-1000 1 1 1 1 3 4 4 4 4 1 4 4 4 4 1 1 1 2 1 La ley gubernamental prohbe la operacin de radiotransmisores no autorizados dentro de los territorios que se encuentren bajo el control del gobierno. La operacin ilegal se castigar con multa y/o encarcelamiento. Solicite la reparacin solamente a un tcnico cualificado. OPERACIONES BSICAS Serie NX-5000 La ilustracin muestra el modelo con un panel de operacin (Opcin: KCH-19) adjunto. Seguridad: Es importante que el operador conozca y entienda los peligros comunes derivados del uso de cualquier transceptor. Pantalla Maintain a separation distance from the antenna to person(s) of at least the distance indicated in the table below. You, as the qualified end-user of this radio device must control the exposure conditions of bystanders to ensure the minimum separation distance (table below) is maintained between the antenna and nearby persons for satisfying RF Exposure compliance. The operation of this transmitter must satisfy the requirements of Occupational/Controlled Exposure Environment, for work-related use, transmit only when person(s) are at least the minimum distance from the properly installed, externally mounted antenna. Transmit only when people outside the vehicle are at least the recommended minimum lateral distance away from the antenna/vehicle. Antenna Minimum Safe Distance Frequency Range VHF UHF 700/800 MHz 800/900 MHz Rated Power 50 W 110 W 45 W 100 W 30 W 15 W Safe Distance 170 cm (5.6 feet) 240 cm (7.9 feet) 140 cm (4.6 feet) 160 cm (5.3 feet) 100 cm (3.3 feet) 70 cm (2.3 feet) One or more of the following statements may be applicable:
FCC WARNING This equipment generates or uses radio frequency energy. Changes or modifications to this equipment may cause harmful interference unless the modifications are expressly approved by the party responsible/
JVCKENWOOD. The user could lose the authority to operate this equipment if an unauthorized change or modification is made. INFORMATION TO THE DIGITAL DEVICE USER REQUIRED BY THE FCC This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can generate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that the interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment to an outlet on a circuit different from that to which the receiver is connected. Consult the dealer for technical assistance. Le fonctionnement de cet metteur doit satisfaire aux exigences dun environnement exposition contrle/
professionnel pour lutilisation lie au travail, nmettre que lorsquune ou plusieurs personnes se trouvent une distance au moins gale la distance minimum par rapport lantenne correctement installe en extrieur. Nmettez que lorsque les personnes en dehors du vhicule se trouvent une distance au moins gale la distance latrale minimum recommande par rapport lantenne/au vhicule. Distance minimum de scurit par rapport l'antenne Gamme de frquences VHF UHF 700/800 MHz 800/900 MHz Puissance nominale 50 W 110 W 45 W 100 W 30 W 15 W Distance de scurit 170 cm (5,6 pieds) 240 cm (7,9 pieds) 140 cm (4,6 pieds) 160 cm (5,3 pieds) 100 cm (3,3 pieds) 70 cm (2,3 pieds) Ce metteur-transmetteur est autoris pour fonctionner avec un facteur dutilisation maximum de 50%, en mode caractristique Appuyez pour parler, afin de satisfaire les limites dexposition aux radiofrequences FCC/ ISED. Lmetteur/rcepteur exempt de licence contenu dans le prsent appareil est conforme aux CNR dInnovation, Sciences et Dveloppement conomique Canada applicables aux appareils radio exempts de licence. Lexploitation est autorise aux deux conditions suivantes :
1 Lappareil ne doit pas produire de brouillage;
2 Lappareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible den compromettre le fonctionnement.
(Srie NX-5000/ NX-3000)
(NX-5000 series)
(NX-5000/ NX-3000 series) SD and microSD are trademarks of SD-3C, LLC in the United States and/or other countries. SD et microSD sont des marques commerciales de SD-3C, LLC aux tats-Unis et/ou dans dautres pays. SD y microSD son marcas comerciales de SD-3C, LLC en los Estados Unidos y/o en otros pases. The Bluetooth word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and any use of such marks by JVCKENWOOD Corporation is under license. Other trademarks and trade names are those of their respective owners. La marque et le logos Bluetooth sont des marques dposes appartenant Bluetooth SIG, Inc. et toute utilisation de ces marques par JVCKENWOOD Corporation est sous licence. Les autres marques et noms commerciaux sont ceux de leurs propritaires respectifs. La marca denominativa y los logotipos de Bluetooth son marcas registradas propiedad de Bluetooth SIG, Inc. y JVCKENWOOD Corporation utiliza dichas marcas bajo licencia. Otras marcas comerciales y nombres comerciales pertenecen a sus respectivos propietarios. This transceiver uses a software according to the following license agreements.
*zlib LICENSE (NX-5000/ NX-3000 series) Copyright (C) 1995-2013 Jean-loup Gailly and Mark Adler This software is provided 'as-is', without any express or implied warranty. In no event will the authors be held liable for any damages arising from the use of this software. Permission is granted to anyone to use this software for any purpose, including commercial applications, and to alter it and redistribute it freely, subject to the following restrictions:
1. The origin of this software must not be misrepresented; you must not claim that you wrote the original software. If you use this software in a product, an acknowledgment in the product documentation would be appreciated but is not required. 2. Altered source versions must be plainly marked as such, and must not be misrepresented as being the original software. 3. This notice may not be removed or altered from any source distribution. Jean-loup Gailly (jloup@gzip.org) Mark Adler (madler@alumni.caltech.edu)
*libpng LICENSE (NX-5000/ NX-3000 series) This copy of the libpng notices is provided for your convenience. In case of any discrepancy between this copy and the notices in the file png.h that is included in the libpng distribution, the latter shall prevail. COPYRIGHT NOTICE, DISCLAIMER, and LICENSE:
If you modify libpng you may insert additional notices immediately following this sentence. This code is released under the libpng license. libpng versions 1.2.6, August 15, 2004, through 1.6.8, December 19, 2013, are Copyright (c) 2004, 2006-2013 Glenn Randers-Pehrson, and are distributed according to the same disclaimer and license as libpng-1.2.5 with the following individual added to the list of Contributing Authors Cosmin Truta libpng versions 1.0.7, July 1, 2000, through 1.2.5 - October 3, 2002, are Copyright (c) 2000-2002 Glenn Randers-Pehrson, and are distributed according to the same disclaimer and license as libpng-1.0.6 with the following individuals added to the list of Contributing Authors This transmitter is authorized to operate with a maximum duty factor of 50%, in typical push-to-talk mode, for satisfying FCC/ ISED RF exposure compliance requirements. INFORMATION ON SOFTWARE LICENSE ADVERTENCIA AMBIENTES EXPLOSIVOS (GASES, POLVO, HUMOS, etc.) Desconecte el transceptor mientras abastece combustible, o cuando haya estacionado en una gasolinera. No transporte recipientes conteniendo combustible de recambio en el portaequipajes de su vehculo si ha instalado su transceptor en el rea del portaequipajes. LESIONES OCASIONADAS POR TRANSMISIONES DE RADIOFRECUENCIA No opere su transceptor cuando haya alguna persona cerca o en contacto con la antena para evitar la posibilidad de que se produzcan quemaduras por alta frecuencia o lesiones fsicas relacionadas. DETONADORES DE DINAMITA La operacin del transceptor dentro de un radio de 150 metros de los detonadores de dinamita podra producir una explosin. Desconecte la alimentacin de su transceptor en un sitio donde se estn haciendo voladuras o donde haya carteles con la indicacin APAGAR LOS APARATOS DE RADIOCOMUNICACION BILATERAL. Si est transportando detonadores en su vehculo, asegrese de hacerlo en cajas metlicas blindadas con almohadillado interior. No transmita mientras se estn poniendo o sacando los detonadores de sus cajas. PRECAUCIONES Observe las siguientes precauciones para evitar incendios, lesiones personales y daos al transceptor. No intente configurar el transceptor mientras conduce, ya que resulta demasiado peligroso. No desmonte ni modifique el transceptor bajo ningn concepto. No exponga el transceptor a la luz directa del sol durante periodos de tiempo prolongados, ni lo coloque cerca de calefactores. Si detecta un olor anormal o humo procedente del transceptor, desconecte inmediatamente la alimentacin y pngase en contacto con su proveedor KENWOOD. El uso del transceptor mientras conduce puede infringir las leyes de trfico. Consulte y respete el reglamento de trfico de su pas. No utilice opciones no especificadas por KENWOOD. No coloque la bolsa de plstico utilizada para el embalaje de este equipo en lugares al alcance de los nios. Si se coloca sobre la cabeza puede causar asfix. No coloque el transceptor sobre superficies inestables. Mantenga el volumen lo ms bajo posible para proteger sus odos. Apague el transceptor antes de instalar los accesorios opcionales. A la hora de desechar la batera incorporada, asegrese de cumplir con las normas y regulaciones de JVCKENWOOD Corporation estar exenta de cualesquiera responsabilidades por las prdidas o daos incidentales como, por ejemplo, falta de comunicaciones u oportunidades de comunicacin causadas por un fallo o error de rendimiento del transceptor. A la hora de desechar la batera incorporada, asegrese de cumplir con las normas y regulaciones de su pas o regin. su pas o regin. Si se forma condensacin, deje que se seque al aire o djela en el mismo entorno durante un periodo prolongado de tiempo para eliminar la condensacin antes de usarla. Para usar un altavoz externo, seleccione un altavoz con la siguiente impedancia y potencia de entrada mxima:
Serie NX-5000/ Serie NX-3000 :
Serie NX-1000 :
4 / 4 W 4 / 6 W No utilice KES-3 para el transceptor de la serie NX-1000. 2022 Indicador de estado Botones operacin Altavoz Sensor de iluminacin Serie NX-3000 Pantalla Micrfono Conmutador PTT Indicador de estado Botones operacin Altavoz Serie NX-1000 Pantalla Indicador de estado Botones operacin Altavoz
] para activar el transceptor.
] para apagar el transceptor. ENCENDIDO Y APAGADO Pulse [
Vuelva a pulsar [
AJUSTE DEL VOLUMEN Pulse el botn programado como [Subir volumen] para aumentar el volumen. Pulse el botn programado como [Bajar volumen] para reducir el volumen. SELECCIN DE UNA ZONA Y UN CANAL Seleccione la zona deseada utilizando las botones programadas con la funcin [Zona arriba]/ [Zona abajo]
y [Canal arriba]/ [Canal abajo]. TRANSMISIN 1 Seleccione la zona y el canal deseados. 2 Pulse la botn programada con la funcin [Monitor] o [Desactivar silenciamiento] para comprobar si el canal est libre. Si el canal est ocupado, espere hasta que quede libre. 3 Presione el conmutador PTT y hable al micrfono. Suelte el conmutador PTT para recibir. Para obtener una calidad de sonido optima, sujete el micrfono a 3 4 cm (1,5 pulgadas) de la boca. RECEPCIN Seleccione la zona y el canal deseados. Si se ha programado la funcin de sealizacin en el canal seleccionado, slo oir las llamadas en las que la seal recibida coincida con la configuracin del transceptor. This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canadas licence-exempt RSS(s). Operation is subject to the following two conditions:
1 This device may not cause interference. 2 This device must accept any interference, including interference that may cause undesired operation Simon-Pierre Cadieux Gilles Vollant Eric S. Raymond and with the following additions to the disclaimer:
of the device.
(NX-5000/ NX-3000 series) SUPPLIER'S DECLARATION OF CONFORMITY 47 CFR 2.1077 Compliance Information Trade name: KENWOOD Model(s): NX-5000 series, NX-3000 series, NX-1000 series Responsible party: JVCKENWOOD USA Corporation 1440 Corporate Drive, Irving, TX 75038 Telephone number: 972-819-0700 This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Tom Lane Willem van Schaik Glenn Randers-Pehrson John Bowler Sam Bushell Greg Roelofs Kevin Bracey Magnus Holmgren Tom Tanner There is no warranty against interference with your enjoyment of the library or against infringement. There is no warranty that our efforts or the library will fulfill any of your particular purposes or needs. This library is provided with all faults, and the entire risk of satisfactory quality, performance, accuracy, and effort is with the user. libpng versions 0.97, January 1998, through 1.0.6, March 20, 2000, are Copyright (c) 1998, 1999 Glenn Randers-Pehrson, and are distributed according to the same disclaimer and license as libpng-0.96, with the following individuals added to the list of Contributing Authors:
libpng versions 0.89, June 1996, through 0.96, May 1997, are Copyright (c) 1996, 1997 Andreas Dilger Distributed according to the same disclaimer and license as libpng-0.88, with the following individuals added to the list of Contributing Authors:
libpng versions 0.5, May 1995, through 0.88, January 1996, are Copyright (c) 1995, 1996 Guy Eric Schalnat, Group 42, Inc. For the purposes of this copyright and license, Contributing Authors is defined as the following set of individuals:
CONSIGNES DE SCURIT OBLIGATOIRES DESTINES AUX INSTALLATEURS ET AUX UTILISATEURS Andreas Dilger Guy Eric Schalnat Tim Wegner Dave Martindale Paul Schmidt Nutilisez que des antennes fournies par le fabricant ou le revendeur. Distance minimum de scurit par rapport lantenne : Reportez-vous aux valeurs indiques dans le tableau ci-dessous. Gain dantenne : 0 dBd par rapport un diple. La Federal Communications Commission a dict une norme de scurit pour lexposition humaine lnergie des RF (radiofrquences) qui se situe en de des seuils fixs par lOSHA (Occupational Safety and Health Act). Installation de lantenne: lantenne fournie par le fabricant ou le revendeur radio ne doit pas tre monte dans un endroit tel que pendant que la transmission par hyperfrquences, des personnes peuvent se rapprocher de la distance de scurit minimale indique dans le tableau ci-dessous. Afin de respecter les seuils actuels dexposition aux RF fixs par la FCC/ ISED, lantenne doit tre installe une distance suprieure ou gale la distance minimum de scurit indique ci-dessus et en accord avec les exigences du fabricant ou du fournisseur de lantenne. Installation du vhicule : lantenne peut tre place au centre du toit mtallique ou du capot du coffre dun vhicule si la distance minimum de scurit est respecte. Installation de la station de base : lantenne doit tre installe sur une structure permanente extrieure. Les seuils dexposition la RF doivent tre respects lors de linstallation. Remplacement de lantenne : ne remplacez pas lantenne par celle fournie ou recommande par le fabricant ou le revendeur de la radio. Vous risquez dexposer une ou plusieurs personnes un niveau de radiofrquence excessif. Vous pouvez vous adresser votre revendeur ou au fabricant pour plus dinformations. AVERTISSEMENT Maintenir une distance de sparation de lantenne aux personnes dau minimum la distance indique dans le tableau ci-dessous. The PNG Reference Library is supplied AS IS. The Contributing Authors and Group 42, Inc. disclaim all warranties, expressed or implied, including, without limitation, the warranties of merchantability and of fitness for any purpose. The Contributing Authors and Group 42, Inc. assume no liability for direct, indirect, incidental, special, exemplary, or consequential damages, which may result from the use of the PNG Reference Library, even if advised of the possibility of such damage. Permission is hereby granted to use, copy, modify, and distribute this source code, or portions hereof, for any purpose, without fee, subject to the following restrictions:
1. The origin of this source code must not be misrepresented. 2. Altered versions must be plainly marked as such and must not be misrepresented as being the original source. 3. This Copyright notice may not be removed or altered from any source or altered source distribution. The Contributing Authors and Group 42, Inc. specifically permit, without fee, and encourage the use of this source code as a component to supporting the PNG file format in commercial products. If you use this source code in a product, acknowledgment is not required but would be appreciated. A png_get_copyright function is available, for convenient use in about boxes and the like:
printf("%s",png_get_copyright(NULL));
Also, the PNG logo (in PNG format, of course) is supplied in the files pngbar.png and pngbar.jpg (88x31) and pngnow.png (98x31). Libpng is OSI Certified Open Source Software. OSI Certified Open Source is a certification mark of the Open Source Initiative. Glenn Randers-Pehrson glennrp at users.sourceforge.net December 19, 2013
*Md5 (NX-5000/ NX-3000/ NX-1000 series) Copyright (C) 1999, 2000, 2002 Aladdin Enterprises. All rights reserved. This software is provided 'as-is', without any express or implied warranty. In no event will the authors be held liable for any damages arising from the use of this software. Permission is granted to anyone to use this software for any purpose, including commercial applications, and to alter it and redistribute it freely, subject to the following restrictions:
1. The origin of this software must not be misrepresented; you must not claim that you wrote the original software. If you use this software in a product, an acknowledgment in the product documentation would be appreciated but is not required. 2. Altered source versions must be plainly marked as such, and must not be misrepresented as being the original software. 3. This notice may not be removed or altered from any source distribution. Vous devez, en votre qualit dutilisateur final qualifi de cet appareil radio, contrler les conditions dexposition des passants afin de vous assurer que la distance minimum de sparation (tableau ci-dessous) est maintenue entre lantenne et les personnes alentour afin de satisfaire aux normes dexposition la RF. L. Peter Deutsch ghost@aladdin.com