NXR-1700 INSTRUCTION MANUAL MODE DEMPLOI MANUAL DE INSTRUCCIONES MANUALE DI ISTRUZIONI BEDIENUNGSANLEITUNG GEBRUIKSAANWIJZING KULLANIM KILAVUZU
MANUAL DE INSTRUES B5A-3612-00 (E)
product is protected by intellectual property rights including patent rights, copyrights and trade secrets of Digital Voice Systems, Inc. This voice coding Technology is licensed solely
Technology is explicitly prohibited from attempting to extract, remove, decompile, reverse engineer, or disassemble the Object Code, or in any other way convert the Object Code into a human-readable form. U.S. Patent Nos. #7,970,606, #8,359,197,
#8,315,860, and #8,595,002.
Corporation. UNPACKING AND CHECKING EQUIPMENT Note: KENWOOD dealer, an authorized KENWOOD service center, or the factory.
material. If any items are missing or have been damaged during
Item Remarks Quantity
4 m (with fuse box)
Reinforcing hardware
Instruction manual Short type
1 1 1 4 1 8 1 4 1 Note: Use only the supplied screws. INSTALLATION To install the handles onto the repeater, align the handles with the
screws. Consult your dealer for installing the repeater and antenna.
NXR-1700
We are grateful you purchased this KENWOOD repeater. THANK YOU!
PRECAUTIONS
Do not expose the repeater to rain or moisture in order to prevent Do not open the repeater under any circumstances in order to Do not expose the repeater to long periods of direct sunlight, nor Firmware Copyrights
place it close to heating appliances. Do not place the repeater in excessively dusty and/or humid areas, nor on unstable surfaces.
in a place which can be reached by a small child's hands. It will
KENWOOD.
repeater, disconnect the power from the repeater immediately, and contact your KENWOOD service center or dealer.
the front of the main body or the fan at the rear. NOTICES TO THE USER Government law prohibits the operation of unlicensed radio transmitters within the territories under government control.
Do not install the repeater in an explosive atmosphere (of
powders, etc.). WARNING CAUTION
the antenna located outdoors on the rooftop or on an antenna tower. This repeater is designed for a 13.2 V DC power source. Never use a 24 V DC or higher source to power the repeater. Use only the supplied DC cord. Do not remove the ferrite core connected to the DC power cable. Removal may cause harmful interference with radio communications. Do not put anything on top of the repeater. Putting something on top obstructs heat dissipation.
During transmission, do not touch the antenna terminals or the
Do not touch the metal surface of the repeater during use.
Continuous listening to loud sounds can cause hearing
Use only the supplied DC power cable or a KENWOOD optional DC power cable. Do not cut and/or remove the fuse holder on the DC power cable. 1 CONTROLS AND FUNCTIONS Front Rear STATUS indicator
is abnormal. DC jack
TX OUT jack Connect a TX antenna or a duplexer to this N receptacle. CONTROL I/O jack Connect a repeater controller or a remote panel to this
RX IN jack
TX RX REPEATER OPERATION CONTROL I/O Note The RX1/ RX2 indicator lights green while receiving a signal and the TX1/ TX2 indicator lights red while transmitting. TRANSCEIVER OPERATION Note adapter. Receive
may need to readjust the volume if you are having interference while receiving a message from your dispatcher or another
RX1/ RX2 indicator lights green while a signal is being received. Transmit 1 being used. 2 Change the Test PTT Control
TX1/ TX2 indicator lights red while transmitting. 3 Test PTT Control to
Display
repeater. POWER indicator
on.
POWER switch/selector
When DC power is supplied to the repeater, the power is automatically turned on. When power is no longer
LAN jack
USB jack (A-Type)
TX1/ TX2 indicator During DMR transmission, the TX1 indicator lights red when communicating with the radio in Timeslot 1, and the TX2 indicator lights red when communicating with the radio in Timeslot 2.
TX1 and TX2 are lit during transmission.
RX1/ RX2 indicator On the DMR standby channel, the RX1 indicator lights green while receiving a receivable CC matching signal in Timeslot 1. The RX2 indicator lights green while receiving a receivable CC matching signal in Timeslot 2.
RX1 and RX2 are lit while receiving a signal with matching signaling and only RX1 is lit while receiving a signal that does not match signaling.
2 FCC WARNING This equipment generates or uses radio frequency energy. Changes or modifications to this equipment may cause harmful interference unless the modifications are expressly approved by the party responsible/
JVCKENWOOD. The user could lose the authority to operate this equipment if an unauthorized change or modification is made. INFORMATION TO THE DIGITAL DEVICE USER REQUIRED BY THE FCC This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can generate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that the interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna. Connect the equipment to an outlet on a circuit different from that to Increase the separation between the equipment and receiver. which the receiver is connected. Consult the dealer for technical assistance. SUPPLIER'S DECLARATION OF CONFORMITY 47 CFR 2.1077 Compliance Information Trade name: KENWOOD Model(s): NXR-1700 Responsible party: JVCKENWOOD USA Corporation 1440 Corporate Drive, Irving, TX 75038 Telephone number: 972-819-0700 MANDATORY SAFETY INSTRUCTIONS TO INSTALLERS AND USERS Use only manufacturer or dealer supplied antenna. Antenna Minimum Safe Distance: Refer to the values in the table below. Antenna Gain: 0 dBd referenced to a dipole. The Federal Communications Commission has adopted a safety standard for human exposure to RF (Radio Frequency) energy which is below the OSHA (Occupational Safety and Health Act) limits. Antenna Mounting: The antenna supplied by the manufacturer or radio dealer must not be mounted at a location such that during radio transmission, any person or persons can come closer than the minimum safe distance indicated in the table below. To comply with current FCC/ ISED RF Exposure limits, the antenna must be installed at or exceeding the minimum safe distance shown above, and in accordance with the requirements of the antenna manufacturer or supplier. Vehicle installation: The antenna can be mounted at the center of a vehicle metal roof or trunk lid, if the minimum safe distance is observed. Base Station Installation: The antenna should be fixed-mounted on an outdoor permanent structure. RF Exposure compliance must be addressed at the time of installation. Antenna substitution: Do not substitute any antenna for the one supplied or recommended by the manufacturer or radio dealer. You may be exposing person or persons to excess radio frequency radiation. You may contact your radio dealer or the manufacturer for further instructions. WARNING Maintain a separation distance from the antenna to person(s) of at least the distance indicated in the table below. You, as the qualified end-user of this radio device must control the exposure conditions of bystanders to ensure the minimum separation distance (table below) is maintained between the antenna and nearby persons for satisfying RF Exposure compliance. The operation of this transmitter must satisfy the requirements of Occupational/Controlled Exposure Environment, for work-
related use, transmit only when person(s) are at least the minimum distance from the properly installed, externally mounted antenna. Transmit only when people outside the vehicle are at least the recommended minimum lateral distance away from the antenna/vehicle. Antenna Minimum Safe Distance NXR-1700-E 160 cm (5.3 feet) 2022