ED2833 KAGA FEI Co., Ltd. 23-Jan.2023 Ver.0.1 User manual
(for ED2833) FCC ID: 2A6NFED2833 IC: 28568-ED2833 KAGA FEI Co., Ltd. 1/5 ED2833 KAGA FEI Co., Ltd. 23-Jan.2023 Ver.0.1 This module should be installed in the host device according to the interface specification . 1) Japan Regulatory Information a) This module is approved with the specic antenna on this module. b) Please ensure that your product can bear a label with the following information. If the product is so small that it is not practicable to place the label, please place it in the instruction manual and package. This product installs a radio system which has been approved as a radio station in a low power data communication system based on the Radio Law. ED2833 : 005-103105 2) Canada Regulatory Information The following information must be indicated on the host device of this module;
a) This device complies with Innovation, Science and Economic Development Canadas applicable licence-exempt RSSs. Operation is subject to the following two conditions:
(1) This device may not cause interference; and
(2) This device must accept any interference, including interference that may cause undesired operation of the device. Le prsent appareil est conforme aux CNR d Innovation, Sciences et Dveloppement conomique Canada applicables aux appareils radio exempts de licence. Lexploitation est autorise aux deux conditions suivantes :
1) lappareil ne doit pas produire de brouillage;
2) lutilisateur de lappareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible den compromettre le fonctionnement. b) This product is certified as type of the portable device with Innovation, Science and Economic Development Canada Rules. To maintain compliance with RF Exposure requirement, please use within specification of this product and have a separation distance of minimum 15 mm between the user and/or bystander and the antenna and
/or radiating element. This distance ensures that the output power (e.i.r.p.) of ED2833 is below the SAR evaluation Exemption limits defined in RSS-102 issue 5. Ce produit est certifi comme type de l'appareil portable avec Rgles de Innovation, Sciences et Dveloppement conomique Canada. Pour maintenir l'acquiescement avec exigence Exposition de RF, veuillez utiliser dans spcification de ce produit et respecter une distance de sparation d'au moins 15 mm entre l'utilisateur et / ou un tiers et l'antenne et / ou l'lment rayonnant. Cette distance garantit que la puissance de sortie (p.i.r.e.) dED2833 est infrieure aux limites dexemption de lvaluation SAR dfinies dans le numro 5 de la norme RSS-102.
- IC: 28568-ED2833 KAGA FEI Co., Ltd. 2/5 ED2833 KAGA FEI Co., Ltd. 23-Jan.2023 Ver.0.1 c) Please notify certified ID by either one of the following method on your product.
-Contains IC : 28568-ED2833 Specifiez ID certifie dans votre produit par une de mthode suivante.
-Contains IC : 28568-ED2833 3) FCC Regulatory Information a) This device complies with part 15 of the FCC Rules.
-Part 15 Subpart C b) The following statement shall be indicated on the host device or the user manual of the host device; Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. c) Please notify certified ID by either one of the following method on your product.
-Contains Transmitter Module FCC ID: 2A6NFED2833
-Contains FCC ID: 2A6NFED2833 d) The following statement shall be indicated in the user manual of the host device;
CAUTION: Changes or modifications not expressly approved by the party responsible for compliance could void the uses authority to operate the equipment. e) The modular transmitter is only FCC authorized for the specific rule parts (Part 15 Subpart C) listed on the grant, and the host product manufacturer is responsible for compliance to any other FCC rules that apply to the host not covered by the modular transmitter grant of certification. The final host product still requires Part 15 Subpart B compliance testing with the modular transmitter installed. f) This product is certified as type of the portable device with FCC Rules. To maintain compliance with RF Exposure requirement, please use within specification of this product. g) The following statement shall be indicated in the user manual of the host device; The antenna used for this transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. h) This module can change the output power depending on the circumstances by the application software which is developed by module installer. Any end user cannot change the output power. i) Antenna List No.1 Antenna Category Antenna Type Dimensions Monopole PCB antenna 8.6mm x 7.5mm 4) CE Regulatory Information a) When your end product installs this module, it is required to proceed additional certification processes before placing on the market in EU member states to make your products fully comply with relative EU standards. b) KAGA FEI can provide you the test reports of conducted measurement portion for the radio module. You can utilize the test reports for the certification processes of your end product as it requires radio testing. KAGA FEI Co., Ltd. 3/5 ED2833 KAGA FEI Co., Ltd. 23-Jan.2023 Ver.0.1 Control No.
(1/2) Control name Pin Layout Pin Descriptions Pin 1 Pin name GND (Corner pad) Pin function Power Description Ground 0.55mm x 0.8mm 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 VBUS D-
D+
P0.07 P0.08 GND P0.01/XL2 P0.00/XL1 P0.04_AIN2 Power USB USB Digital I/O Digital I/O Power Digital I/O Analog input Digital I/O Analog input Digital I/O Analog input 5 V input for USB 3.3 V regulator USB D-
USB D+
General purpose I/O, Trace buffer clock General purpose I/O Ground General purpose I/O Connection for 32.768 kHz crystal General purpose I/O Connection for 32.768 kHz crystal General purpose I/O Analog input GND (Corner pad) Power Ground 0.55mm x 0.8mm P0.26 GND OUT_MOD Digital I/O Power RF In/Out OUT_ANT Antenna In/Out GND (Corner pad) GND (Corner pad) P0.10_NFC2 SWDIO VDD VDDH DECUSB Power Power Digital I/O NFC input Debug Power Power Power General purpose I/O Ground RF I/O pin. It should be connected to Pin15 OUT_ANT for normal operation. Internal antenna. It should be connected to Pin14 OUT_MOD for normal operation Ground 0.55mm x 0.8mm Ground 0.55mm x 0.8mm General purpose I/O NFC antenna connection Serial wire debug I/O for debug and programming Power supply High voltage power supply USB 3.3V regulator supply decoupling KAGA FEI Co., Ltd. 4/5 ED2833 KAGA FEI Co., Ltd. 23-Jan.2023 Ver.0.1 Control No.
(2/2) Control name Pin Layout Pin 23 Pin name P0.15 P0.05_AIN3 P0.06 P0.30_AIN6 P0.27 P0.28_AIN4 P0.31_AIN7 P0.02_AIN0 P0.03_AIN1 P0.29_AIN5 P0.09_NFC1 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 Pin function Digital I/O Digital I/O Analog input Digital I/O Digital I/O Analog input Digital I/O Digital I/O Analog input Digital I/O Analog input Digital I/O Analog input Digital I/O Analog input Digital I/O Analog input Digital I/O NFC input Description General purpose I/O General purpose I/O Analog input General purpose I/O General purpose I/O Analog input General purpose I/O General purpose I/O Analog input General purpose I/O Analog input General purpose I/O Analog input General purpose I/O Analog input General purpose I/O Analog input General purpose I/O NFC antenna connection General purpose I/O Configurable as pin RESET Serial wire debug clock input for debug and programming P0.18_RESET Digital I/O SWDCLK Debug GND (Center pad) Power Ground 2.8mm x 1.5 mm NC (Corner pad) NC (Corner pad) NC NC NC 0.55mm x 0.8mm NC 0.55mm x 0.8mm KAGA FEI Co., Ltd. 5/5