WARNING:pdfminer.pdfpage:The PDF <_io.BufferedReader name='/Volumes/Scratch/Incoming/eg-scratch/6638907.pdf'> contains a metadata field indicating that it should not allow text extraction. Ignoring this field and proceeding. Use the check_extractable if you want to raise an error in this case ED2840 KAGA FEI Co., Ltd. 06-Jun.2023 Vwe.0.1 User manual
(for ED2840) FCC ID: 2A6NFED2840 IC: 28568-ED2840 KAGA FEI Co., Ltd. 1/6 06-Jun.2023 Vwe.0.1 ED2840 KAGA FEI Co., Ltd. This module should be installed in the host device according to the interface specification. 1) Japan Regulatory Information a) This module is approved with the specic antenna on this module. Please ensure that your product can also bear a label with the following information. If the product is so small that it is not practicable to place the label, you can also place it in the instruction manual and package. The mark diameter shall be easily legible without using a device such as light microscopes. 005-103104 b) It is recommended to include the following sentence in the user manual of your product:
This product installs a radio system which has been approved as a radio station in a low power data communication system based on the Radio Law. ED2840 005-103104 2) Canada Regulatory Information a) This device complies with Innovation, Science and Economic Development Canadas applicable license-exempt RSSs. Operation is subject to the following two conditions:
(1) this device may not cause interference, and
(2) this device must accept any interference, including interference that may cause undesired operation of the device. Le prsent appareil est conforme aux CNR dInnovation, Sciences et Dveloppement conomique Canada applicables aux appareils radio exempts de licence. Lexploitation est autorise aux deux conditions suivantes:
1) lappareil ne doit pas produire de brouillage;
2) lutilisateur de lappareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible den compromettre le fonctionnement. b) This product is certified as type of the portable device with Innovation, Science and Economic Development Canada Rules. To maintain compliance with RF Exposure requirement, please use within specification of this product and have a separation distance of minimum 15 mm between the user and/or bystander and the antenna and /or radiating element. This distance ensures that the output power (e.i.r.p.) of ED2840 is below the SAR evaluation Exemption limits defined in RSS-102 issue 5. Ce produit est certifi comme type de l'appareil portable avec Innovation, Sciences et Dveloppement conomique Canada Rgles. Pour maintenir l'acquiescement avec exigence Exposition de RF, veuillez utiliser dans spcification de ce produit et respecter une distance de sparation d'au moins 15 mm entre l'utilisateur et / ou un tiers et l'antenne et / ou l'lment rayonnant. Cette distance garantit que la puissance de sortie (p.i.r.e.) d ED2840 est infrieure aux limites dexemption de lvaluation SAR dfinies dans le numro 5 de la norme RSS-102. c) Please notify certified ID by either one of the following methods on your product. Specifiez ID certifie dans votre produit par une de mthode suivante.
-Contains Transmitter module IC : 28568-ED2840
-Contains IC : 28568-ED2840 KAGA FEI Co., Ltd. 2/6 06-Jun.2023 Vwe.0.1 ED2840 KAGA FEI Co., Ltd. d) Please indicate your product name at any location on the exterior of the host product or product packaging or product literature, which shall be available with the host product or online. e) Please include the following statements in rectangle on the user manual of the host device of this module;
This device complies with Innovation, Science and Economic Development Canada license-exempt RSS standards. Operation is subject to the following two conditions:
(1) This device may not cause interference.
(2) This device must accept any interference, including interference that may cause undesired operation of the device. Le prsent appareil est conforme aux CNR Innovation, Sciences et Dveloppement conomique Canada applicables auxappareils radio exempts de licence. Lexploitation est autorise aux deux conditions suivantes :
1) lappareil ne doit pas produire de brouillage;
2) lutilisateur de lappareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible den compromettre le fonctionnement. 3) FCC Regulatory Information a) This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired operation. b) Please notify certified ID by either one of the following methods on your product.
-Contains Transmitter Module FCC ID: 2A6NFED2840
-Contains FCC ID: 2A6NFED2840 c) CAUTION: Changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. d) This product is certified as type of the portable device with FCC Rules. To maintain compliance with RF Exposure requirement, please use within specification of this product. e) The antenna used for this transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. f) This module can change the output power depending on the circumstances by the application software which is developed by module installer. Any end user cannot change the output power. g) This device complies with part 15 of the FCC Rules.
-Part 15 Subpart C KAGA FEI Co., Ltd. 3/6 06-Jun.2023 Vwe.0.1 ED2840 KAGA FEI Co., Ltd. h) The modular transmitter is only FCC authorized for the specific rule parts (Part 15 Subpart C) listed on the grant, and the host product manufacturer is responsible for compliance to any other FCC rules that apply to the host not covered by the modular transmitter grant of certification. The final host product still requires Part 15 Subpart B compliance testing with the modular transmitter installed. i) Co-location of this module with other transmitters that operate simultaneously are required to be evaluated using the FCC multi transmitter procedures. When installing this module to your final devices, please make sure to carry out all the necessary evaluations according to the applicable guidelines like follows:
-for RF exposure: KDB 447498, KDB 996369 and any other relevant guidelines
-for EMC: KDB 996369 D04 and any other relevant guidelines j) When you install this module to your final devices, please ensure that your final composite product complies with the applicable FCC rules in reference to a guidance in KDB 996369. k) Antenna List This module is approved along with the following antenna. You cannot use any antennas other than the listed one because it deviates from the accredited conditions. Manufacturer Part No. KAGA FEI N/A (Printed on PCB) Dimensions 8.6mm x 7.5mm Antenna Type Maximum Antenna Gain Monopole 2.5dBi l) Please include the following statements in rectangle on the user manual of the host device of this module;
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired operation. FCC CAUTION: Changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. The antenna used for this transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. This product is certified as type of the portable device with FCC Rules. To maintain compliance with RF Exposure requirement, please use within specification of this product. 4) CE Regulatory Information a) When your end product installs this module, it is required to proceed additional certification processes before placing on the market in EU member states to make your products fully comply with relative EU standards. b) KAGA FEI can provide you the test reports of conducted measurement portion for the radio module. You can utilize the test reports for the certification processes of your end product as it requires radio testing. KAGA FEI Co., Ltd. 4/6 ED2840 KAGA FEI Co., Ltd. 06-Jun.2023 Vwe.0.1 Control No.
(1/2) Control name Pin Layout Pin Descriptions Pin 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 Pin name GND (Corner pad) VBUS D-
D+
P0.07 P0.08 GND P0.01/XL2 P0.00/XL1 P0.04_AIN2 GND (Corner pad) P0.26 GND OUT_MOD Pin function Ground Power Digital I/O Digital I/O Digital I/O Digital I/O Ground Digital I/O Analog input Digital I/O Analog input Digital I/O Analog input Ground Digital I/O Ground RF In/Out OUT_ANT Antenna In/Out GND (Corner pad) GND (Corner pad) P0.10_NFC2 SWDIO VDD VDDH DECUSB P0.15 P0.05_AIN3 P0.06 P0.30_AIN6 P0.27 P0.28_AIN4 P0.31_AIN7 P0.02_AIN0 P0.03_AIN1 P0.29_AIN5 P0.09_NFC1 Ground Ground Digital I/O NFC input Debug Power Power Power Digital I/O Digital I/O Analog input Digital I/O Digital I/O Analog input Digital I/O Digital I/O Analog input Digital I/O Analog input Digital I/O Analog input Digital I/O Analog input Digital I/O Analog input Digital I/O NFC input Description Ground 0.55mm x 0.8mm 5 V input for USB 3.3 V regulator USB D-
USB D+
General purpose I/O, Trace buffer clock General purpose I/O Ground General purpose I/O Connection for 32.768 kHz crystal General purpose I/O Connection for 32.768 kHz crystal General purpose I/O Analog input Ground 0.55mm x 0.8mm General purpose I/O Ground RF I/O pin. It should be connected to Pin15 OUT_ANT for normal operation. Internal antenna. It should be connected to Pin14 OUT_MOD for normal operation Ground 0.55mm x 0.8mm Ground 0.55mm x 0.8mm General purpose I/O NFC antenna connection Serial wire debug I/O for debug and programming Power supply High voltage power supply USB 3.3V regulator supply decoupling General purpose I/O General purpose I/O Analog input General purpose I/O General purpose I/O Analog input General purpose I/O General purpose I/O Analog input General purpose I/O Analog input General purpose I/O Analog input General purpose I/O Analog input General purpose I/O Analog input General purpose I/O NFC antenna connection KAGA FEI Co., Ltd. 5/6 ED2840 KAGA FEI Co., Ltd. Control No.
(2/2) Control name Pin Layout 06-Jun.2023 Vwe.0.1 Pin Pin name Pin function 34 35 36 37 38 P0.18_RESET Digital I/O SWDCLK GND (Center pad) NC (Corner pad) NC (Corner pad) Debug Ground NC NC Description General purpose I/O Configurable as system RESET
(Factory default : GPIO) Serial wire debug clock input for debug and programming Ground 2.8mm x 1.5 mm NC 0.55mm x 0.8mm NC 0.55mm x 0.8mm KAGA FEI Co., Ltd. 6/6