FCC ID: 2AKE4WPC2 Wireless Pipe Clamp

Quick Start Guide for UEi HUB Tools v2 SETUP:

Download and install the UEi HUB App Open the App and navigate to the appropriate Tools Connection Screen for the tool you wish to connect. Tap the tool box icon on the Ref Side display to connect to WPP1, WPC2 and WOT2 tools. Tap the tool box icon on the Air Side display to connect to WHP1 tools. Tap the tool box icon on the Vac display to connect to WVG2 tools. Power on the HUB Tools and wait until you see the flashing green LED. WOT2, WVG2, WPP1 Press and hold Power button for 1 second. WHP1 Press the probe release and extend the sensing probe 90 or 180 until it locks in place. WPC2 Open the clamp jaw by placing a cylinder with a diameter larger than 9mm in the jaw. In the App you will see the tools appear in the Nearby Tools list. If tools are missing tap the refresh icon and the list will refresh. Touch and Drag a tool from the Nearby Tool list to an appropriate assignment slot

(Match the tool icon to the slot you wish to assign it to. To see tool values and associated calculated values return to the Display Screen by tapping the back button. You can swipe between the Vacuum, Refrigerant and Air side displays. You are now ready to monitor live measurements from your UEi HUB tools. SPECIFICATIONS:

WHP1:

Temperature Operating Range: 32 to 60C (0 to 140F) Resolution: 0.1 Accuracy: 0.3C (0.5F) Drift: <0.03C/yr Relative Humidity Operating Range: 0 to 100%

Resolution: 0.1%

Accuracy: 3%

Drift: <0.25%/yr Operating Conditions Temperature: -41 to 140F (5 to 60C)

%RH: 20 to 80%

Storage Conditions (Batteries removed) Temperature: -40 to 257F (-40 to 125C) Ingress protection IP 52 Power Battery type: 2 AAA Alkaline Batteries Battery Life: 100+ hrs. WPP1:

Pressure Operating Range: 0 to 50 bar (0 to 725 PSI) Resolution: 0.1 PSI Accuracy: 0.5% F.S. (2.5 to 5.0 PSIG) Operating Conditions Temperature: 14 to 158F (-10 to 70C)

%RH: 30 to 85%

Storage Conditions (Batteries removed) Temperature: -13 to 185F (-25 to 85C) Ingress protection IP 52 Power Battery type: 2 AA Alkaline Batteries Battery Life: 100+ hrs. WPC2:

Temperature Operating Range: 0 to 82C (32 to 180F) Otherwise 0.5C (1.0F) Resolution: 0.1 Accuracy: 0.3C (0.6F) For 10C to 80C Operating Conditions Temperature: 32 to 180F (0 to 82C) Storage Conditions (Batteries removed) Temperature: 14 to 104F (-10 to 40C)

< 75% RH Ingress protection IP 52 Power Battery type: 1 AA Alkaline Battery WOT2:

Temperature Operating Range: 0 to 82C (32 to 180F) Resolution: 0.1 Accuracy: 1.0C (2F) Operating Conditions Temperature: 32 to 180F (0 to 82C) Storage Conditions (Batteries removed) Temperature: 14 to 104F (-10 to 40C)

< 75% RH Ingress protection IP 52 Power Battery type: 2 AA Alkaline Battery WVG2:

Vacuum Pressure:

Range: 0-20000 microns Resolution: 1 micron Accuracy: 5% reading 5 microns Max Over Pressure: 700 PSI Temperature Operating Range: -12 to 50C (10 to 122F) Resolution: 0.1 Accuracy: 2.5C (5F) Operating Conditions Temperature: 10 to 122F (-12 to 50C) Power Battery type: 2 AA Alkaline Battery FCC and IC STATEMENT This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna. Connect the equipment into an outlet on a circuit different from that to which the receiver is Increase the separation between the equipment and receiver. connected. Consult the dealer or an experienced radio/TV technician for help. This equipment complies with FCC/IC RSS102 radiation exposure limits set forth for an uncontrolled envi ronment. This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful communication. Conformment la rglementation d'Industrie Canada, le prsent metteur radio peut fonctionner avec une antenne d'un type et d'un gain maximal (ou infrieur) approuv pour l'metteur par Industrie Canada. Dans le but de rduire les risques de brouillage radiolectrique l'intention des autres utilisateurs, il faut choisir le type d'antenne et son gain de sorte que la puissance isotrope rayone quivalente (p.i.r.e.) ne dpasse pas l'intensit ncessaire l'tablissement d'une communication satisfaisante. Le prsent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autoris e aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible d'en compromettre le fonctionnement. FCC AND IC NOTICE This device complies with Part 15 of the FCC rules and Industry Canada license-exempt RSS 247. Operation is subject to the following two conditions: (1) This device may not cause harmful interference;

and (2) this device must accept any interference received, including interference that may cause undesired operation. Cet appareil est conforme la partie 15 des rgles de la FCC, ainsi qu la norme RSS 247 exempte de licence dIndustrie Canada. Son fonctionnement est soumis aux deux conditions suivantes : (1) Cet appareil ne doit pas provoquer dinterfrences nuisibles; et (2) cet appareil doit accepter toutes les interfrences reues, y compris celles susceptibles dentraner un dysfonctionnement de lappareil. FCC CAUTION The device must not be co-located or operated in conjunction with any other antenna or transmitter. Caution the user that changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. L'appareil ne doit pas tre plac ou utilis conjointement avec une autre antenne ou un autre metteur. Attention l'utilisateur que des changements ou des modifications non expressment approuvs par la partie responsable pour la conformit pourrait annuler l'autorit de l'utilisateur pour faire fonctionner l'quipement. a.The device should be installed and operated with a minimum distance of 20cm between the radiator and your body. L'appareil doit tre install et utilis avec une distance minimale de 20 cm entre le radiateu et votre corps. b.This device complies with RSS247 of Industry Canada. Cet appareil se conforme RSS247 de Canada d'Industrie. This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. appareils radio exempts de licence. Son fonctionnement est sujet aux deux conditions suivantes: (1) le dispositif ne doit pas produire de brouillage prejudiciable, et (2) ce dispositif doit accepter tout brouillage recu, y compris un brouillage susceptible de provoquer un fonctionnement indesirable. This Class B digital apparatus complies with Canadian ICES-003. Cet appareil numrique de la classe B est conforme a la norme NMB-003 du Canada. Exposure of humans to RF fields (RSS-102) The computers employ low gain integral antennas that do not emit RF field in excess of Health Canada limits for the general population; consult Safety Code 6, obtainable from Health Canada's Web site at http://www.hc-sc.gc.ca/

The radiated energy from the antennas connected to the wireless adapters conforms to the IC limit of the RF exposure requirement regarding IC RSS-102, Issue 5 clause 4. SAR tests are conducted using recommended operating positions accepted by the FCC/ RSS with the device transmitting at its highest certified power level in all tested frequency band without distance attaching away from the body. Non-

compliance with the above restrictions may result in violation of FCC RF exposure guidelines. Conformit des appareils de radiocommunication aux limites d'exposition humaine aux radiofrquences

(CNR-102) L'ordinateur utilise des antennes intgrales faible gain qui n'mettent pas un champ lectromagntique suprieur aux normes imposes par Sant Canada pour la population. Consultez le Code de scurit 6 sur le site Internet de Sant Canada l'adresse suivante : http://www.hc-sc.gc.ca/

L'nergie mise par les antennes relies aux cartes sans fil respecte la limite d'exposition aux radiofrquences telle que dfinie par Industrie Canada dans la clause 4.1 du document CNR-102, version 5. Tests DAS sont effectus en utilisant les positions recommandes par la FCC/CNR avec le tlphone met la puissance certifie maximale dans toutes les bandes de frquences testes sans distance attacher loin du corps. Non-respect des restrictions ci-dessus peut entraner une violation des directives de la FCC/CNR.

A? ; oN fas -\

a a 775 Montague Expressway Milpitas, CA 95035 1828 / Tel: 408-526-1188 Ea enc Fax: 408-526-1088 mail: sales.eaw@us.bureauveritas.com Project and Product Certification Representative Authorization Letter CT Revision Histo Reason for Amendment (current / obsolete) From To Approved Date Initial Release (obsolete) 1.0 1.0 Nov-14-2006 Revised wording (obsolete) 1.0 2.0 Sept-25-2007 Updated company template (obsolete) 2.0 3.0 Jan-31-2012 Updated letter information (obsolete) 3.0 4.0 May-23-2014 Added FCC ID field (obsolete) 4.0 5.0 Sep-16-2014 Updated company name & logo (current) 5.0 6.0 Jun-27-2018 SCS-F18: Project and Product Certification Representative Authorization Letter Page 1 of 2 Rev 6.0 Kane USA Inc 2020/01/02 To: BVCPS, INC. 775 Montague Expressway, Milpitas, CA 95035 USA Dear Sir/Madam, Re: Product Certification Representative Authorization Letter We, Kane USA Inc. hereby authorize Bureau Veritas Consumer Product Services, Inc. to act as a Certification Body for certifying for the following project(s):

FCC ID: 2AKE4WPC2 Product Description: Wireless Pipe Clamp Model: WPC2 Sincerely, Client's signature Client's name / title /: oft Schultz/ ProductCoordinator Contact information / address: 7601 E 88th Place, Indianapolis IN 46256, USA SCS-F 18: Project and Product Certification Representative Authorization Letter Page 2 of 2 Rev 6.0

BUREAU 775 Montague Expressway Milpitas, CA 95035 Tel: 408-526-1188 Fax: 408-526-1088 Email: sales.eaw@us.bureauveritas.com Confidentiality Request Letter Revision Histo!

Reason for Amendment (current / obsolete) From To Approved Date Initial Release (obsolete) 1.0 1.0 Nov-14-2006 Adding CFR 2.459 (obsolete) 1.0 2.0 August - 11 - 2008 Updated company template & Added text box 2.0 3.0 Jan-31-2012

(obsolete) Added IC confidentiality letter form (obsolete) 3.0 4.0 March-26-2015 Corrections to STC form. Added reference to KDB 40 5.0 Nov-19-2015

(obsolete) Updated company logo (current) 5.0 6.0 Jun-26-2019 SCS-F19: Confidentiality Request Letter Page | of 2 Rev 6.0 Kane USA Inc. 2020/01/09 To:

Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD Subject: Permanent Confidentiality Request for FCC ID: 2AKE4WPC2 Pursuant to sections 0.457 and 0.459 of CFR 47, we respectfully request permanent confidential treatment of the following Exhibits accompanying this application as:

- e.g. Block Diagram

- e.g. Schematics

- e.g. Operational Description The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these materials may be harmful to the applicant and provide unjustified benefits to its competitors. The applicant understands that disclosure of this application and all accompanying documentation will not be made before the date of the Grant for this application. Sincerely, Client's signature:

Client's name & titl: Jeff Schultz/ Product Coordinator Contact information / address: 7601 E 88th Place, Indianapolis IN 46256, USA SCS-F19: Confidentiality Request Letter Page 2 of 2 Rev 6.0