FCC ID: 2ATRP-SWITCH SWITCH

Racing Electronics SWITCH DESCRIPTION Always hear the Race Officials over your Team Radio conversations. This is what the SWITCH does. The Racing Electronics SWITCH And SWITCH RACER combine a 2 Channels Radio Receiver with an Audio Input Port and an Audio Output Port. The Audio Input Port is connected to the output of your 2 way radio. It is internally looped to the Output Port where your headsets are connected so that you normally hear the conversation with your Team. Messages from Officials are detected by the built in Receiver and immediately routed to your headsets. When this happens, your 2 way Radio Audio is attenuated. The frequencies of the 2 channels are Preset but programmable. The Switch is however fully versatile to be used different ways as follow:

1. The Audio from the Audio Input Port is not mandatory. If used, it will always be attenuated when activity is detected on a Preset Channel. You can connect any audio source to that port. 2. The Preset Channels can be used as follow:

a. Hold on Preset Channel 1 (Always the default at power ON. Fully programmable) b. Hold on Preset Channel 2 (Fully programmable) c. SCAN Preset Channel 1 or 2. (activity must finish on an active channel before switching to other channel. Not available in SWITCH RACER) d. SCAN with Priority on Preset Channel 1. (Channel 1 interrupts channel 2. Not available on SWITCH RACER) e. SCAN with Priority on Preset Channel 2. (Channel 2 interrupts channel 1. Not Available on SWITCH RACER) The SWITCH is shipped with Preset Channel 1 programmed at 454.0000 MHz, the frequency for the NASCAR Officials. You can however reprogram the frequency to any of the available 12.5 Khz bandwidth channels in the 450-470 MHz range. It is fully compliant with todays Motor Racing sanctioning body. The SWITCH takes advantage of the Analog and Digital Squelch technology (DTCSS/CDCSS, PL/DPL from Motorola TM). Using that sub Channel technology insures that if a frequency is used by more than one team, you can select to listen only to the one you want from its sub Channel number. The SWITCH generates distortion free audio, loud enough for the race environment. The Audio Input Port accepts 1/8 jack, mono or stereo. Headsets with 1/8 mono or stereo jack can be connected to the Audio Output Port. The Switch Operates from 2 AAA batteries. Normal Alcaline batteries provide 7 hours of continuous operation. A Battery Low indicator turns ON when you still have only 30 minutes of full Racing Electronics SWITCH Manual Version 2.0 11/05/2017 operation. After that, the Radio receiver is turned OFF. In that mode, you still have 5 hours of operation but from the Audio Input Port only. The SWITCH comes with 2x AAA batteries, a lanyard & instruction manual. SPECIFICATIONS Features Audio In:

Yes, cabled Always muted when one RF Channel is active. RF Channels:

2, from built in Radio receiver Preset but programmable by user Automatic scan:

Functionality:

Between preset channels 1 and 2 only. (Not available on SWITCH RACER) Hold on Channel Ch1 or Ch2, Operation:

Scan, Scan Priority Ch1, SCAN Priority Ch2 (Not available on SWITCH RACER) Normal (Audio In, Ch1 or Ch2) Battery Low (Audio In, CH1 or Ch2) Bypass mode (Audio In only, RF receiver is OFF when battery too low) Battery Low Indicator:

Built In memory:

Yes Yes, (last preset saved, even when changing batteries) Compliance:

Compliant with official Motor Racing sanctioning body. RF Radio Receiver Frequency Range:

Channels Bandwidth:

Sub Channel Technology: Analog CTCSS or PL (Motorola TM) 450 MHz to 470 MHz 12.5 KHz, for a total of 1600 channels Digital CDCSS or DPL (Motorola TM) Mechanical:

Dimensions:

Weight:

3.00"W x 1.75"H x .80"D 0,2 g (without batteries) Electrical:

Audio Input:

Audio Output:

1/8 (3.5mm) Stereo socket, accepts mono and Stereo jack 1/8 (3.5mm) for Stereo earbuds/Headsets, 8 to 32 Ohms Audio Output Level:

User adjustable for internal RF receiver. Power:

Audio from Audio In adjusted from connected device only. Batteries:

Battery life:

2x AAA (included) 7 Hours (continuous) + 5 Hours in bypass mode Accessories:

Included:

Lanyard with safety clip and quick detach User manual Optionnal accessories:

Belt-clip Earbuds Racing Electronics SWITCH Manual Version 2.0 11/05/2017 Racing Electronics Switch Operation OPERATION MODE (Default mode when you power ON) Audio In Audio In. Used to connect a Radio device, Cell phone or Music player. The volume level for that input is controlled by the connected device only. This audio input is always attenuated whenever a signal is present on Preset Channel 1 or 2. Accepts mono or stereo 1/8 jack. Audio Out Audio Out. Used to connect headphones or earbuds. Accepts 1/8 mono or stereo jack. Power ON-OFF. Hold for 2 Seconds to power ON-OFF. to select Preset Channel 1. This Channel is always the default at power ON. Preset Channel 1. Press Its as shipped value is NASCAR Officials frequency of 454.0000 Mhz. Preset Channel 2. Press SCAN, Press must terminate before the scanning process resumes. (Not Available on SWITCH RACER) SCAN Priority 1, Hold active, it will interrupt Preset 2. (Not Available on SWITCH RACER) to select Preset 2. and press to SCAN between Preset 1 and 2. Once a conversation on one of the Preset is active, it to start SCAN with Priority on Preset 1. If Preset 1 becomes SCAN Priority 2, Hold active, it will interrupt Preset 1. (Not Available on SWITCH RACER) and press to start SCAN with Priority on Preset 2. If Preset 2 becomes Volume UP. Press to increase volume of Preset 1 or 2. Volume Down. Press to decrease volume of Preset 1 or 2. Long Press Long Press Long Press Long Press Long Press PROGRAMMING. Hold Programming Sections. Hold for 2 seconds to display Preset 1 sub channel information. for 2 seconds to enter programming mode. Details are provided below, in the Hold for 2 seconds to display Preset 2 sub channel information. PROGRAMMING (Basic) 1. Press or hold 2. Press 3. Press PROGRAMMING Mode access. Hold or for 2 seconds to enter programming mode. key to select the desired channel or frequency. twice to exit programming mode and monitor the new channel. or to exit Programming mode without storing the new frequency and return to selected Preset. or 4. Long Press store the new frequency as Preset 1 or 2. PROGRAMMING (Advanced) PROGRAMMING MODE access. Hold or for 2 seconds to enter programming mode. to select the desired channel or frequency. to access sub Channel programming. or key to select the desired sub channel number. to exit programming mode and monitor the new channel. 1. Press or hold 2. Press 3. Press or hold 4. Press 5. Press or to selected Preset. to exit Programming mode without storing the new frequency and return 6. Long Press or to store the frequency and its sub channel as Preset 1 or 2 and exit programming mode. Racing Electronics SWITCH Manual Version 2.0 11/05/2017 Avoid Hearing Damage !

To prevent possible hearing damage, do not use the SWITCH at high volume for a long period of time and always lower the volume level of the device you connect to the SWITCH Audio Input port before connecting. ID : _To be provided Model: SWITCH and SWITCH RACER This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference.

(2) this device must accept any interference received, including interference that may cause undesired operation. WARNING:

Modification of this device to receive cellular radio telephone service signals is prohibited under FCC rules and Federal Laws. The complete declaration is available online at: www.racingelectronics.com Racing Electronics SWITCH Manual Version 1.0 11/05/2017 Version 2.0 11/05/2017

EXHIBIT A - FCC ID LABEL AND LOCATION FCC ID Label FCC ID Label Location Information The label shown shall be permanently affixed at a conspicuous location on the device and be readily visible to the user at the time purchase (Labeling requirements per 2.925)

Kangaroo Media Inc Address: 20865 Ch de la Cote nord, suite 101 Boisbriand, Quebec, J7E 4H5 Canada Tel.: 450-595-2023 Fax: 450-595-2023 E-mail: ptremblay@fanvision.com 2020-01-21 Federal Communications Commission Authorization and Evaluation Division, 7435 Oakland Mills Road Columbia, MD 21046 USA Re: SWITCH (FCC ID: 2ATRP-SWITCH) Gentlemen:

The scanner receiver equipment meets the requirements of the FCC Rules, 15.121 (a). Compliance is achieved through the following methods:

The scanner receiver in this equipment is incapable of tuning, or readily being altered, by the User to operate within the frequency bands allocated to the Domestic Public Cellular Telecommunications Service in Part 22. Blocking of the cellular frequencies is implemented in the firmware of the units main control central processing unit (CPU). Coverage of 824

-849 MHz and 869 - 894 MHz is completely blocked, since it is done in the microprocessor,and cannot be re-enabled by any user-accessible procedure, including diode, resistor, or jumper changes, nor by connection of any external device such as a personal computer, nor by installation of any special enabling semiconductor device. The scanning receiver is designed so that the tuning, control and filtering circuitry is inaccessible. Sincerely, Kangaroo Media Inc Pascal M. Tremblay Project Manager

Kangaroo Media Inc Address: 20865 Ch de la Cote nord, suite 101 Boisbriand, Quebec, J7E 4H5 Canada Tel.: 450-595-2023 Fax: 450-595-2023 E-mail: ptremblay@fanvision.com FCC Confidential Authorization Date: 2019-12-02 FEDERAL COMMUNICATIONS COMMISSIONS Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 Subject: Confidentiality Request regarding application for certification of FCC ID: 2ATRP-SWITCH In accordance with Sections 0.457 and 0.459 of the Commissions Rules, Kangaroo Media Inc hereby requests long-term confidential treatment of information accompanying this application as outlined below:

Block Diagram Schematics Operation Description Internal photos The above materials contain proprietary and confidential information not customarily released to the public. The public disclosure of these materials provides unjustified benefits to its competitors in the market. Sincerely Yours, Pascal M. Tremblay Project Manager

Authorization Date: 2019-12-02 FEDERAL COMMUNICATIONS COMMISSIONS Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 Subject: Agent Authorization To whom it may concern:

We, Kangaroo Media Inc hereby authorizes Bay Area Compliance Laboratories Corporation to act on its behalf in all matters relating to application for Equipment FUiNeer Zee MURS ta Nema: Reuotlese eB OCU oem RTE emPaN ECan) CeCe MBNA Ree ee lee RO meci mums latest Mihm tC same effect as our own action. We, the undersigned, hereby certify that we are not subject to a denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988 21 U.S.C. 862. This authorization is valid until further written notice from the applicant. Sincerely Yours, Surely Pascal M. Tremblay eee) umyenitctoy QA-FR-170-B Kangaroo Media Inc Address: 20865 Ch de la Cote nord, suite 101 Boisbriand, Quebec, J7E 4H5 Canada Tel.: 450-595-2023 Fax: 450-595-2023 E-mail: ptremblay@fanvision.com

KangarooMediaInc Address:20865ChdelaCotenord,suite101Boisbriand,Quebec,J7E4H5Canada Tel.:4505952023 Fax:4505952023 Email:ptremblay@fanvision.com Product Similarity Declaration 2019-12-02 To:

FEDERAL COMMUNICATIONS COMMISSIONS Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 Dear Sir/Madam, We, Kangaroo Media Inc hereby declare that we have a product named as SWITCH

(Model: SWITCH, FCC ID: 2ATRP-SWITCH) was tested by BACL, Meanwhile, for our marketing purpose, we would like to list a series model (SWITCH RACER) on reports and certificate. The two models have the same circuit. The differences are as follows:

1. The model name is different. 2. SWITCH RACER does not have the SCAN button. It has no SCAN function. We confirm that all information above is true, and well be responsible for all the consequences. Please contact me if you have any question. Sincerely Yours, PascalM.Tremblay ProjectManager