FCC ID: WQT-KSTB4314 KSTB4314

KSTB4134 The information presented in this document is subject to change. We reserve the right, without prior notice, to make changes in the design of the product or performance due to advances in technology and/or reasons of force majeure, market conditions or contractual aspects. Safety Precaustions This decoder was manufactured in accordance with international safety standards. Please read the following recommended safety precautions carefully. POWER SUPPLY: Alternating Current (AC) 100~240V 50/60Hz LOCATION: Place the decoder indoors. Keep the receiver away from potential hazards such as household plants, lighting, rain and direct exposure to sunlight. OVERLOAD: Do not overload wall outlets, extension cords or adaptors, as they can cause fires or electric shocks. LIQUIDS: Do not expose the unit to drips or splashes of water and make sure no objects containing liquid, such as glasses, are placed on the unit. CLEANING: Before cleaning the decoder, disconnect it from the wall outlet. Use a soft cloth lightly dampened with water (no solvents) to clean the exterior. VENTILATION: Do not cover the ventilation openings of the decoder. Make sure there is free ventilation around the decoder. Never place the decoder on soft accessories or carpets. Do not use or store the receiver in places exposed to sunlight or near heaters. Do not place other electronic equipment on top of the decoder. Place the receiver at least 30mm from the wall. DEVICES: Do not use any other device that is not recommended by the manufacturer, as it may be dangerous or could cause damage to the equipment. MAINTENANCE: Do not attempt to repair the product. Any attempt to repair it will invalidate the warranty. All repairs must be carried out by our qualified customer service staff. INSTALLATION 1. Connect the coaxial cable Connect the coaxial cable to the COAX-IN port located on the rear of your decoder (see rear panel 1). 2. Connect the HDMI cable Connect one end of the HDMI cable to the HDMI port (see rear panel 2). INITIAL CONFIGURATION The equipment has an installation menu which is visible at the time of installation of the decoder or after each use of "Restore factory settings through the menu. This installation menu allows you to configure the following options:

1. Language: Select the language to be used in the user interface. 2. Select your country: The network parameters are automatically configured according to the selected country 3. Channel Scan: The channel scan starts. 4. Update channel list: The channel list will be updated with the scanned channels Menu To view the main menu 1. Press the Home button or 2. Press the left button while watching live channels Basic Functions 1. Program Information: Press the Info button or the Down button to see the information of the channel you are watching 2. Channel List: Press the OK button to see the list of channels, while watching live channels 3. Audio/Subtitle: Press the Audio/Subtitle button or Right button to configure Audio/Subtitle of the channel you are watching. Program Guide 1. Press the Guide button or Select the menu Settings Guide to access the program guide 2. Press the OK button on the program to tune the channel Favorites 1. Press the FAV button to access the favorite channels 2. If there is no favorite channel, you will be redirected to the page to add favorite channels. Parent Control 1. All adult channels are blocked by default 2. Events that are in the adult content category are also blocked by default 3. The default PIN to unblock a channel or an adult event is: 4321 To make changes in the configuration, Select the menu Settings System Parental Control Front Panel 1 2 3 1. INFRARED SENSOR: This element is to receive commands from the Remote Control, do not block it to allow proper interaction with the decoder. 2. POWER: This key is used to turn on and off the decoder (put it in Active or Passive stand by mode). 3. INDICATOR LIGHT: Green light color indicates equipment is on, Red light color indicates Active Stand By, LED off indicates Passive Stand By or disconnected. Rear Panel 1 2 3 4 1. CABLE IN: RF signal input, here connects the coaxial cable that the television operator provides. 2. HDMI: High definition output to connect to the TV on the HDMI input. 3. Ethernet: Port to connect Ethernet cables 4. POWER SUPPLY: Port to connect the decoder power adapter. REMOTE CONTROL 1. PWR: On/Off of the Decoder. 2. TV PWR: On/Off of the Television. 3. AUDIO: Audio management 4. SUB-T: Subtitle management 5. OPT: Shows additional options. 6. GUIDE: Shows the TV channel programming guide. 7. INFO: Shows information about the current channel and program to follow, date and time, when pressed again shows detailed information and, 8. FAV: favorites list 9. Navigation Keys / / /

10. OK: Confirms the selected option, in TV mode shows a mini channel list. 11. Exit: Close the menus and go to the watched channel. 12. BACK: Go back to the previous section 13. Home: Go to the home screen 14. VOL + /VOL -: Increase Volume / Reduce Volume 15. CH / CH : go up channel / go down channel 16. MUTE: silence channel 17. Numeric keys (0 - 9) 18. TV/RADIO: Go to the last tuned TV/Radio channel 19. LAST: return to previous channel FCC Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

-Reorient or relocate the receiving antenna.

-Increase the separation between the equipment and receiver.

-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

-Consult the dealer or an experienced radio/TV technician for help. To assure continued compliance, any changes or modifications not expressly approved by the party. Responsible for compliance could void the users authority to operate this equipment. (Example- use only shielded interface cables when connecting to computer or peripheral devices). This equipment complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and

(2) This device must accept any interference received, including interference that may cause undesired operation. FCC Radiation Exposure Statement:

The equipment complies with FCC Radiation exposure limits set forth for uncontrolled enviroment. This equipment should be installed and operated with minimum distance 20cm between the radiator and your body.

Appendix Label PRODUCT LABEL ON SET AND GIFTBOX QUANTITY: 2 MATERIALS: 50# GLOSSY WHITE PET SIZE:60*30MM Appendix Label Location FCC ID:WQT-KSTB4314 www.cotecna-toby.com TB-RF-073-3.1

KAON Group Co., Ltd. Add: Kaonmedia Building, 884-3, Seongnam-daero, Bundang-gu, Seongnam-si, Gyeonggi-do, Republic of Korea Date: 2026/8/26 FCC ID: WOT-KSTB4314 Dear Sir/Madam, We, KAON Group Co., Ltd., have a KSTB4314 that assembled a WIFI MODULE (model:

6222B-SRC, FCC ID: 2AATL-6222B-SRC). Hereby we, KAON Group Co., Ltd., declare that this WIFI MODULE is no changed except the BT and 2.4G WLAN are disabled by software. TBR-C-202606-0243-1 test reports quoted the module FCC ID: 2AATL-6222B-SRC (The maximum conducted power is verified to be the same. The conducted signal test data may be re-used, please check Report No.: A2303077-C01-R04). Product name: KSTB4314 Model no.: KSTB4314 Sincerely, Name/Title: Jeong Hyeon Kim/Manager Company: KAON Group Co, Ltd. Address: Kaonmedia Building, 884-3, Seongnam-daero, Bundang-gu, Seongnam-si, Gyeonggi-do, Republic of Korea Phone: 82+10-4724-4580 Fax: +82-31-724-8999 E-Mail: [email protected]

FCC Statement-US_re-use data of modules For Certification Service in the USA Federal Communications Commission Equipment Authorization Division, Application Processing Branch 7435 Oakland Mills Road Columbia, MD 21048 To whom it may concern Statement of re-use of original test results of approved radio modules according to KDB 996369 D02 Module Q and A v1 Q1(a) Reference of new FCC ID application:

FCCID | Model name WOT-KSTB4314 | ksTB4314 We, KAON Group Co., Ltd., the undersigned, hereby declare that our radio device hosts the following approved radio module(s):

Grantee: FN-LINK TECHNOLOGY LIMITED Type of Module: Single Modular Report FCCID: | 2AATL-62228-SRC Reference A2303077-CO1-RO4 The module(s) is/are installed according to the installation instructions of the module manufacturer(s) without modification. The original module test report(s) accurately represent all conducted measured test results under the new conditions. All radiated measurements according to the applicable radio standard(s), the rf-exposure and simultaneous transmission evaluation are performed and reported for the entire host. If you have any questions, please feel free to contact us at the address shown below. Sincerely, Signature Date: 2026/8/26 Printed Name of Signee: Jeong Hyeon Kim/Manager Company: KAON Group Co., Ltd. Address: Kaonmedia Building, 884-3, Seongnam-daero, Bundang-gu, Seongnam-si, Gyeonggi-

do, Republic of Korea Phone:82+10-4724-4580 Fax: +82-31-724-8999 Email: [email protected]

Local Representative Letter For Certification Service in the USA Federal Communications Commission Equipment Authorization Division, Application Processing Branch 7435 Oakland Mills Road Columbia, MD 21048 To whom it may concern Pursuant to Section 2.911(d)(7), of the Commissions Rules (47 C.F.R.) we attest as follows for the product listed below:

Model name KSTB4314 FCC ID WQT-KSTB4314 We hereby acknowledge as follows:

i. both signees confirm that the point of contact accepts responsibility to act as a US-

American Representative on behalf of the applicant ii, the point of contact provides the physical U.S. address and email as listed below iii. | both parties maintain the requirements of this agreement for no less than one year after the grantee has terminated all marketing and importation or the conclusion of any Commission-related proceeding involving the equipment. iv. An expiration date for this letter does not exist. In case the U.S. agent changes, the grantee is obligated to notify the FCC within 30 days via the granting TCB. US-American Point of Contact Applicant/Approval Holder oany Heo Kim) HAIER) 62/2076 Signature Date: 2026-8-2 Signature Date: 2026-8-26 Company Name: ACT Lab LLC KAON Group Co., Ltd. FRN: 0033465568 0018127571 Contact Name: Scott Huber Jeong Hyeon Kim Address: 3280 East 59th Street Long Beach, Kaonmedia Building, 884-3, CA 90805 United States Seongnam-daero, Bundang-gu, Seongnam-si, Gyeonggi-do, Republic of Korea Phone: (562) 470-7215 82+10-4724-4580 Email: [email protected] [email protected]

Lae, Confidentiality Request Letter For Certification Service in the USA Federal Communications Commission Equipment Authorization Division, Application Processing Branch 7435 Oakland Mills Road Columbia, MD 21048 To whom it may concern Pursuant to Paragraphs 0.457 and 0.459 of the Commissions Rules (47 C.F.R.) and Section 552(b)(4) of the Freedom of Information Act, we request confidentiality for the documentation of the following products:

FCC ID Model name WQT-KSTB4314 KSTB4314 For the products listed above, we request permanent confidentiality for all applicable exhibits as there are:

e the Operational Description e the Block Diagram e the Schematics The above listed exhibits contain trade secrets and proprietary information that could be of benefit to our competitors. If you have any questions, please feel free to contact us at the address shown below. Si ly, \, sie Jeon Hyeow KM

{eH HBAS 4}

Signature Date: 2026-8-26 Printed Name of Signee: Jeong Hyeon Kim/ Manager Company: KAON Group Co., Ltd. Address: Kaonmedia Building, 884-3, Seongnam-daero, Bundang-gu, Seongnam-si, Gyeonggi-

do, Republic of Korea Phone: 82+10-4724-4580 Fax: +82-31-724-8999 Email: [email protected]

Covered Equipment Attestation Letter For Certification Service in the USA Federal Communications Commission Equipment Authorization Division, Application Processing Branch 7435 Oakland Mills Road Columbia, MD 21048 To whom it may concern Pursuant to Section 2.911(d)(5)(i)-(ii) of the Commissions Rules (47 C.F.R.) we attest as follows for the product listed below:

FCC ID Model name WAQT-KSTB4314 KSTB4314 We, Applicant Company Name: KAON Group Co., Ltd. Address: Kaonmedia Building, 884-3, Seongnam-

daero, Bundang-gu, Seongnam-si, Gyeonggi-

do, Republic of Korea Phone: 82+10-4724-4580 certify that the equipment for which authorization is sought is not covered equipment prohibited from receiving an equipment authorization pursuant to section 2.903 of the FCC rules. This includes the cybersecurity and anti-virus software produced or provided by Kaspersky Lab, Inc. or any of its successors and assignees. We certify that, as of the date of the filing of the application, the applicant is not identified on the Covered List as an entity producing covered equipment. If you have any questions, please feel free to contact us at the address shown below. Sincerely, y. J aon 4 Hyeoh Kim

(Hr Pi AE 4S}

Signature Date: 2026-8-26 Printed Name of Signee: Jeong Hyeon Kim/ Manager Company: KAON Group Co., Ltd. Address: Kaonmedia Building, 884-3, Seongnam-daero, Bundang-gu, Seongnam-si, Gyeonggi-

do, Republic of Korea Phone: 82+10-4724-4580 Fax: +82-31-724-8999 Email: [email protected]

Nil Declaration Letter For Certification Service in the USA Federal Communications Commission Equipment Authorization Division, Application Processing Branch 7435 Oakland Mills Road Columbia, MD 21048 To whom it may concern MODELNUMBER: KSTB4314

(MODEL NUMBER OF UNIT TESTED) FCC ID: WQT-KSTB4314 Product description: KSTB4314 The following features and technical capabilities are declared for the product shown above:

(1) DFS Device: [|] Master [_] Client with Radar detection Xx] Client without radar detection,

(2) Service capability listing Frequency Active Scanning | passive scanning Ad Hoc Mode Access point Band (MHz) (the device can (where the capability capability transmit a probe device is can

(beacon)) listen only with no probes) 5180-5240 Xl Yes | [_]No | [_]Yes 5190-5230 x] Yes | [_]No | [_]Yes 5210-5210 Xx]yes | |] No | [_] Yes

[ ]Yes | Xx] No

| |Yes | X]No

[ ]Yes | X]No no Chver Se No Yes No erect Cine CDs Tans no | L]yes | KX] No |

Ddno | Llyes | DI No |

Do | L]yes | Xx]No |

Dx] No DJno | [J] ves | Bd No |

[x] No | | Yes XX] No bs Ud bie

(3) Meet 15.202 requirement XX] Yes [_]No A master device is defined as a device operating in a mode in which it has the capability to transmit without receiving an enabling signal. In this mode it is able to select a channel and initiate a network by sending enabling signals to other devices A client device is defined as a device operating in a mode in which the transmissions of the device are under control of the master. A device in client mode is not able to initiate a network.

(4) Statement of Conformity for the Client in Non-Associated mode The client software and associated drivers will not initiate any transmission on DFS frequencies without initiation by a master. This includes restriction on transmissions for beacons and support for ad-hoc peer-to- peer modes.

[-] Apply [X] Does not apply

(If apply, pls help to provide explanation on it was implement, and how software was controlled) Sincerely,

(HEE) Jeong eon, Xi Signature Date 2026-8-26 Printed Name Jeong Hyeon Kim Job Title Manager Company KAON Group Co., Ltd. Address Kaonmedia Building, 884-3, Seongnam-daero, Bundang-gu, Seongnam-si, Gyeonggi-do, Republic of Korea Phone 82+10-4724-4580 Email [email protected]