all | frequencies |
|
exhibits | applications |
---|---|---|---|---|
manual |
app s | submitted / available | |||||||
---|---|---|---|---|---|---|---|---|
1 |
|
User and Installers manual | Users Manual | 3.21 MiB | April 06 2018 | |||
1 | Cover Letter(s) | April 06 2018 | ||||||
1 | External Photos | April 06 2018 | ||||||
1 | Internal Photos | April 06 2018 | ||||||
1 | ID Label/Location Info | April 06 2018 | ||||||
1 | ID Label/Location Info | April 06 2018 | ||||||
1 | Cover Letter(s) | April 06 2018 | ||||||
1 | Test Report | April 06 2018 | ||||||
1 | Test Report | April 06 2018 | ||||||
1 | Test Report | April 06 2018 | ||||||
1 | Test Report | April 06 2018 | ||||||
1 | Test Setup Photos | April 06 2018 |
1 | User and Installers manual | Users Manual | 3.21 MiB | April 06 2018 |
Technical Manual Roadside ITS Station RIS-9160-xx0x This device provides communication protocols based on IEEE WAVE or ETSI ITS G5 Standards Doc No. 47000001566 Version 02 Order number:
47000001566 Document type THb Document issue 02 Document status released Date of issue 2018-02-01 Valid from Author:
Tugrul Gner, Alfred Brendinger Assessor:
Alfred Brendinger, Peter Ullrich, Heinz Liebhart, Alexander Paier, Herbert Diemling Release:
Tugrul Gner Disclaimer and Limitation of Liability The products described in this manual are provided as is and without any warranties of any kind, either express or implied. Kapsch TrafficCom disclaims all warranties, express or implied, including, but not limited to, warranties of title, legality or non-infringement or misappropriation of any intellectual property rights of third parties or implied warranties of merchantability or fitness for a particular purpose. Under no circumstances will Kapsch TrafficCom (including its affiliates, licensors, contractors, suppliers, assignees, subsidiaries, and the respective officers, directors, employees, shareholders, agents and representatives of each of them) be liable for any expenses, fees, claims, damages or losses in any way relating to or arising out of the products described in this manual. Applicable law may not allow certain warranty exclusions, so one or more of the above disclaimers may not apply to you. Copyright Kapsch TrafficCom AG 2018 Duplication as well as utilization of contents of this documentation are illegal without our explicit consent. 47000001566-THb-02 Table of Contents Page 3 of 36 Page System Overview Associated Documents Information About This Document Warning to Users in the United States Regulatory Information Software Licenses Safety Instructions Maintenance Instructions Inspection Instructions Environmental Information Visual Inspection Installation Instructions General Information 6 6 Text Conventions ............................................................................................ 7 Important Text Elements ................................................................................. 7 Abbreviations ................................................................................................... 8 9 10 11 11 11 11 12 12 12 12 Definitions ...................................................................................................... 12 13 Performance Overview .................................................................................. 13 US Version .................................................................................................... 13 European Version .......................................................................................... 13 System Architecture ...................................................................................... 14 Compact Architecture ........................................................................................14 System Interfaces ..............................................................................................15 19 20 Mounting ........................................................................................................ 20 Device without a mounting plate ........................................................................21 Device with mounting plate M ..........................................................................22 Device with mounting adapter W .....................................................................23 Electrical Installation...................................................................................... 24 Signals at the LAN/PoE System-Connector .......................................................24 System cable connection ...................................................................................25 Product Specifications ................................................................................... 28 Mechanical Dimensions ................................................................................ 31 32 Standards ...................................................................................................... 32 Statement of Conformity ............................................................................... 34 35 Mounting Bracket for RIS-9160 ..................................................................... 35 Protection caps and termination plugs .......................................................... 36 Product versions Installation Optional Equipment Conformity 47000001566-THb-02 Page 4 of 36 Technical Manual | Roadside ITS Station RIS-9160-xx0x Table of Figures Page Figure 1 Roadside ITS Station RIS-9160 ..................................................... 13 Figure 2 Functional block diagram ................................................................ 15 Figure 3 System Interfaces ........................................................................... 15 Figure 4 Auxiliary antenna ports RIS-9160 ................................................... 16 Figure 5 Position of the Status LEDs ............................................................ 17 Figure 6 RIS-9160 without a mounting plate ................................................. 21 Figure 7 RIS-9160 with mounting plate M rear view ............................... 22 Figure 8 RIS-9160 with mounting plate M side view ............................... 22 Figure 9 RIS-9160 with Mounting adapter W ............................................. 23 Figure 10 Remove original gasket ................................................................ 26 Figure 11 Position of the sealing ................................................................... 26 Figure 12 Cable Connection Mounting Details ............................................. 26 Figure 13 Direction of the Rubber Gasket..................................................... 27 Figure 14 RIS-9160 with connected system cable ........................................ 27 Figure 15 Dimensions of RIS-9160 without mounting plate .......................... 31 Figure 16 Dimensions of RIS-9160 with mounting plate M ........................ 31 Figure 17 Dimensions of RIS-9160 with mounting adapter W ................... 32 Figure 18 Mounting Bracket with safety wire ................................................ 35 Figure 19 Dimensions and drilling plan of the Mounting Bracket .................. 35 47000001566-THb-02 Technical Manual | Roadside ITS Station RIS-9160-xx0x Page 5 of 36 List of Tables Table 1 Available Device versions of RIS-9160-xx0x ..................................... 6 Table 2 Text Formats and their Meaning ....................................................... 7 Table 3 D1 General Status LED ................................................................ 17 Table 4 D2 Power LED ............................................................................. 18 Table 5 RIS-9160 device versions ................................................................ 19 Table 6 LAN/PoE connector signals ............................................................ 24 Table 7 Connector assembly parts .............................................................. 25 Table 8 Standards ........................................................................................ 32 Table 9 Protection caps and termination plugs ............................................ 36 47000001566-THb-02 Page 6 of 36 Objective Technical Manual | Roadside ITS Station RIS-9160-xx0x Associated Documents none -
Information About This Document This Manual is the common Description, Installation and Service Manual for the device family RIS-9160-xx0x with Kapsch part numbers 34034340xxx. Available device versions are listed in Table 1. Table 1 Available Device versions of RIS-9160-xx0x Part No. Device name Additional device name Description 34034340000 RIS-9160-1A0M K25104P000000000000 34034340001 RIS-9160-1A00 K25104P000000000000 34034340002 RIS-9160-1A0W K25104P000000000000 Roadside unit with mounting plate M. Roadside unit without a mounting plate. Roadside unit with mounting adapter W. Audience This document is addressed to qualified staff only. Qualified staff have the appropriate knowledge in the scope of electrical engineering. Preparations This Technical Manual shall be carefully read before installation. Customer specific installation guidelines are not described within this document. Dimensions All dimensions used in this document are in metric system except otherwise indicated. 47000001566-THb-02 Technical Manual | Roadside ITS Station RIS-9160-xx0x Page 7 of 36 Table 2 Text Formats and their Meaning Attention Caution Warning Text Conventions Visual aids and standard text formats in this manual help the reader to locate and identify information easily. Typographical formats:
Style Used for bold italics Accentuations Labelling and cross-references CAPITAL LETTERS Acronyms Important Text Elements This manual contains specific Caution and Warning statements. These shall be interpreted as follows:
Attention: This warning indicates that the device may be affected by Electrostatic Discharge. Appropriate precautions must be made to avoid damage to the device. Caution: A caution sign indicates concerns about a procedure which may lead to equipment damage or violation of regulatory requirements. Warning: indicates a potential danger that requires correct procedures or practices in order to prevent injury to humans or damage to the equipment. 47000001566-THb-02 Page 8 of 36 Technical Manual | Roadside ITS Station RIS-9160-xx0x Abbreviations ACR Adjacent Channel Rejection BT DL DSRC EIRP GB GNSS GPIO LOS LTE OBU NACR NLOS PoE PPS RSU RIS SSD UL WAVE WLAN WWAN Bluetooth Downlink direction (Information from RIS-9160) Dedicated Short Range Communication Equivalent Isotropic Radiated Power Giga Byte Global Navigation Satellite System General Purpose Input or Output Line of Sight Long Term Evolution, 4th generation cellular communication technology On Board Unit Non Adjacent Channel Rejection Non Line of Sight Power over Ethernet Pulse Per Second Roadside Unit Roadside ITS Station Solid State Disk Uplink direction (Information to RIS-9160) Wireless Access in a Vehicular Environment, a term used by IEEE 1609.x series of standards Wireless Local Area Network Wireless Wide Area Network 47000001566-THb-02 Technical Manual | Roadside ITS Station RIS-9160-xx0x Page 9 of 36 Local Regulations License Required Warning to Users in the United States The hardware referred to in this document allow selection of frequency bands and transmit power levels that may not comply with the regulatory body that governs spectrum policy where the hardware is being used. The operator is required to apply for and obtain a 47 CFR Part 90 geographic area license from the FCC that has specified eligibility requirements to operate this device in the United States (47 CFR Part 90.375). See product label for FCC ID number. Individual devices have to be registered. Such licenses serve as a prerequisite to registering individual devices located within the licensed geographic area. Licensees must register each installation in the Universal Licensing System
(ULS) before operating a 5.9GHz DSRC Roadside Unit (RSU). For further information about DSRC regulations in the US please refer to https://www.fcc.gov/
47000001566-THb-02 Page 10 of 36 Notice Notice Class B Digital Device Technical Manual | Roadside ITS Station RIS-9160-xx0x Regulatory Information The device versions referred to in this document comply with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
1. This device may not cause harmful interference, and 2. this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications made to this equipment not expressly approved by Kapsch may void the FCC authorization to operate this equipment. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Increase the separation between the equipment and receiver. Reorient or relocate the receiving antenna. Connect the equipment into an outlet on a circuit different from Consult the dealer or an experienced radio/TV technician for help. that to which the receiver is connected. Radio Frequency Radiation Exposure Information This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance of 20 cm (8 inches) between the radiator and a human body. Failure to do so could result in bodily injury or death. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. 47000001566-THb-02 Technical Manual | Roadside ITS Station RIS-9160-xx0x Page 11 of 36 Handling of Cables Grounding Note to GPS System Installer Software Licenses This product may contain software portions including technologies used under third party license, and are copyrighted. Notices, Terms and Conditions pertaining to third party software are located at http://www.kapsch.net/us/en/ktc/portfolio/products_and_components/Pages/
default.aspx Safety Instructions Caution: Cables shall not be bent to a smaller radius than specified by the cable manufacturer. For cables listed in this manual the dending radius shall be larger than 2 inches (5cm) Caution: It is necessary to connect the device to ground with a low impedance connection. This reminder is provided to call the systems installer's attention to Section 820.93 of the NFPA 70 National Electrical Code 2008 Edition, which provide guidelines for proper grounding and, in particular, specify that the coaxial cable shield shall be connected to the grounding system of the building, as close to the point of cable entry as practical. Note: This reminder applies when the GPS antenna is installed remote using a coax-cable between the RIS-9160 and the GPS antenna. Maintenance Instructions The Roadside ITS Station RIS-9160 need no regular electrical maintenance. Inspection Instructions Regular Inspection Warning: Regular inspection of installed equipment is mandatory and shall be in accordance with the local safety regulations for equipment installed on the roadside. 47000001566-THb-02 Page 12 of 36 Recycling Environmental Requirements Transport Communication Zone Technical Manual | Roadside ITS Station RIS-9160-xx0x Environmental Information RIS-9160 equipment set consists of material that can be recycled by specialized companies. Please observe the local regulations regarding the disposal of packaging material and waste electronic equipment. The device is protected against environmental influences by NEMA 4X (IP67) enclosure. No additional protection measures are required for outdoor installation. The specified protection class is only provided when each connector is either closed by a mounted accessory (antenna or cable) with the same protection class or when unused, the connector has to be closed with a dedicated plug which is specified within this document. The device is shipped packed and each antenna port of the device is protected against dust with a plastic dust protection which must be removed before installation. Exposure of the device to direct solar radiation may additionally increase the case temperature. If the requirement for acceptable operational temperature range cannot be satisfied an application specific sun cover must be used. Visual Inspection Always check the shipment for completeness and possible damage. If the content is incomplete or damaged, a claim should be filed with the carrier immediately and contact your local Kapsch office. Installation Instructions For information regarding applications for and installation of the products described in this manual, please see the application notes. General Information Definitions The size of the communication zone is defined by the area where communication with another device (e.g., OBU) is reliable. The size of the communication zone is mostly influenced by the mounting height and mounting angle of the antennas, the antenna utilized, the transmit power level used and environmental effects e.g. buildings, traffic signs, trees and receiving vehicles communication characteristics (receiver sensitivity, antenna, ) etc.. 47000001566-THb-02 Technical Manual | Roadside ITS Station RIS-9160-xx0x Page 13 of 36 System Overview The RIS-9160 implemented in roadside systems supports reliable data exchange with standard (IEEE WAVE or ETSI ITS G5) compliant Onboard Units (OBUs). Figure 1 Roadside ITS Station RIS-9160 Product operates in outdoor and roadside environments Performance Overview Weather proof, robust and compact housing US Version IEEE WAVE/802.11p compliant DSRC transceiver RIS-9160 Compatible with IEEE WAVE/802.11p compliant OBUs European Version ETSI ITS G5 compliant roadside transceiver RIS-9160 Compatible with ETSI ITS G5 compliant OBUs 47000001566-THb-02 Page 14 of 36 Technical Manual | Roadside ITS Station RIS-9160-xx0x System Architecture The Roadside ITS Station RIS-9160 architecture is optimized for easy and fast installation and commissioning. The applied architecture is used for setups with a minimum of auxiliary equipment needed on the roadside. The device includes all functionality to run IEEE WAVE or ETSI ITS G5 functionality. Compact Architecture Scope The applied architecture has the highest flexibility for different system setups. It can be scaled for different needs of the customer. System Structure Common system features:
PoE power supply of the device GB Ethernet based system interface Device is internally protected against surges on data and power lines GPS antenna interface for positioning and time synchronization Two 5.9 antenna interfaces LED status indication Preconfigured optional features:
Internal mSATA SSD for memory extension Internal SD memory card for memory extension Application specific mounting plates Optional features but not available in the described device family in this document:
External 24-48V DC supply in addition to or instead of the PoE+ supply. GPIO interface (3x in, 3x out) WWAN interface WLAN interface BT interface Note: All options need to be installed in the production before delivery. The availability of the options is depending on the product roadmap and customer demand. 47000001566-THb-02 Technical Manual | Roadside ITS Station RIS-9160-xx0x Page 15 of 36 5.9GHz 5.9GHz GNSS WLAN*
BT*
WWAN*
IEEE 802.11p radio (x2*) GNSS WLAN*
BT*
WWAN*
WAVE 1609 ETSI ITS G5 External radio interface extensions 5.9 application layer 5.9 API 5.9GHz radio communication Computer HW platform Linux OS TCP/IP Services Watchdog Unique Serial No Security Services Real Time Clock Temp Sensor Administration Services Platform & Resources & Protocols External Interfaces SSD*
Modular HW & extentions SD*
USB*
mPCIe*
Modular internal extentions Device parameter setting & provisioning Firmware provisioning Self-test / Supervision Web server*
Logging*
Monitoring*
Operation & Maintenance Figure 2 Functional block diagram ETH (PoE) LEDs Ext.Power*
GPIO*
* Option System Interfaces 5.9GHz Antenna port 2 Figure 3 System Interfaces 47000001566-THb-02 PoE / Data Frame Ground Status LEDs 5.9GHz Antenna port 1 Page 16 of 36 Technical Manual | Roadside ITS Station RIS-9160-xx0x Figure 4 Auxiliary antenna ports RIS-9160 Auxiliary Antenna Port 1 GNSS PoE / Data interface PoE/LAN data cable GB Ethernet data interface and also PoE+ power supply input, the external power supply (PoE) is the responsibility of the system integrator and must comply with IEEE 802.3at requirements. A shielded Cat-5e cable or better must be used. Max. Length < 300feet
(<100m) cable must be qualified for PoE+ usage. Also the local environmental conditions ( e.g. UV stability, temperature range) must be considered when choosing the cable. Note: Cat-5e network cable with a conductor cross-section of AWG 24 (0.22 mm2) get fast to physical limits, they might get warm - especially when the heat from big cable bundles can dissipate. Cat-6 or Cat-7A cables with cross sections of AWG 23 (0.26 mm2) or AWG 22 (0.33 mm2) are due to their lower resistance advantageous. Status LEDs Four status LEDs are provided on the bottom side of the device which indicate status information of the RIS-9160. The Led D2 Power provides off/green, each other Led provides the three colors green, amber, red. 47000001566-THb-02 Technical Manual | Roadside ITS Station RIS-9160-xx0x Page 17 of 36 D1 General Status D2 Power D3 Application specific indication D4 Application specific indication Color Status Description Off No operation Power off Green Operation ok Device is fully operational. Green blinking Start Device is doing a start, full operation is not established yet in this state. Amber SW install Software installation is in progress. Full operation not established. Red Fault Device is in a faulty state, operation is limited or not provided depending on the kind of fault. Figure 5 Position of the Status LEDs Table 3 D1 General Status LED 47000001566-THb-02 Page 18 of 36 Technical Manual | Roadside ITS Station RIS-9160-xx0x Color Status Description Off No power Internal power supply is not ok, power off. Table 4 D2 Power LED green Power ok Internal power supply is ok. 5.9 Antenna Ports GNSS Antenna Port Note: The indications of D3 and D4 are described in the appropriate software installation manuals. The RIS-9160 is equipped with two antenna ports for 5.9GHz communication, so external antennas can be applied. 5.9GHz Antenna port 1 is internally connected to the 5.9 Radio 1, port 1. 5.9GHz Antenna port 2 is internally connected to the 5.9 Radio 1, port 2 The RIS-9160 is equipped with an internal GNSS receiver. An antenna port for receiving of position and time information is located on the top side of the device. An external GNSS antenna can directly be applied. Auxiliary Antenna Port 1 is used as GNSS antenna port. Antenna Port Protection If an antenna port is not used it is mandatory to secure the connector with its appropriate closure, see chapter . Caution: Ensure that each antenna port is protected in the correct way whenever changing the usage of a RIS-9160 47000001566-THb-02 Technical Manual | Roadside ITS Station RIS-9160-xx0x Page 19 of 36 Product versions Available versions of the product family RIS-9160-xA0x 34034340xxx:
Table 5 RIS-9160 device versions Part No. Device name Additional device name Description 34034340000 RIS-9160-1A0M K25104P000000000000 34034340001 RIS-9160-1A00 K25104P000000000000 34034340002 RIS-9160-1A0W K25104P000000000000 Roadside unit with PoE+
supply, one 5.9GHz radio unit with dual channel capability, GNSS interface Mounting plate: M. CPU: INTEL-ATOM E3825 1,33GHz, 1GB RAM ECC, 4GB eMMC mSATA SSD: none SD memory card: none Roadside unit with PoE+
supply, one 5.9GHz radio unit with dual channel capability, GNSS interface. mounting plate: none. CPU: INTEL-ATOM E3825 1,33GHz, 1GB RAM ECC, 4GB eMMC mSATA SSD: none SD memory card: none Roadside unit with PoE+
supply, one 5.9GHz radio unit with dual channel capability, GNSS interface. Mounting plate W. CPU: INTEL-ATOM E3825 1,33GHz, 1GB RAM ECC, 4GB eMMC mSATA SSD : none SD memory card: none 47000001566-THb-02 Page 20 of 36 Technical Manual | Roadside ITS Station RIS-9160-xx0x Installation The described mounting applies to RIS-9160 specified in this documentation. Warning: Installation of the RIS-9160 product must be performed by trained Kapsch approved staff. Mounting In general the following rules apply:
The omni-directional 5.9GHz antenna should point against the road
(ground). Typical installation height for RIS-9160 is 6 - 8 meters. Cable outlet LAN heading oriented downwards. Top Bottom Warning: When mounting the device to a bridge, a gantry or a wall the appropriate safety regulations must be followed. 47000001566-THb-02 Technical Manual | Roadside ITS Station RIS-9160-xx0x Page 21 of 36 Device without a mounting plate The bare RIS-9160-xxx0 variants like part number 34034340001 are delivered without a mounting plate but provide four M6-screws on the rear side for mounting. Figure 6 RIS-9160 without a mounting plate 47000001566-THb-02 Page 22 of 36 Figure 7 RIS-9160 with mounting plate M rear view Figure 8 RIS-9160 with mounting plate M side view Technical Manual | Roadside ITS Station RIS-9160-xx0x Device with mounting plate M The variants RIS-9160-xxxM like part number 34034340000 are already equipped with a mounting plate. The mounting plate enables mounting into the mounting bracket 34017690200 without tools (see chapter Mounting Bracket for RIS-9160). It provides an additional connection of the Frame ground and also the possibility to mount a sunshield on the outer four drill holes. Frame Ground Point 47000001566-THb-02 Technical Manual | Roadside ITS Station RIS-9160-xx0x Page 23 of 36 Device with mounting adapter W The variants RIS-9160-xxxW like part number 340340002 are already equipped with the mounting adapter W on the rear side. Figure 9 RIS-9160 with Mounting adapter W 47000001566-THb-02 Page 24 of 36 Recommendation for Cabling Technical Manual | Roadside ITS Station RIS-9160-xx0x Electrical Installation Remark: The cables must be protected against mechanical damage. Optimal protection offers a protective cable guard. Cables must be fixed with cable strap in such a way that the maximum protection against mechanical damage is provided. Table 6 LAN/PoE connector signals LAN/PoE System-Connector Connector Pin Signal Description RJ45 8-pin Socket (female) 1 D1+
18 2 D1-
3 D2+
4 D3+
5 D3-
6 D2-
7 D4+
8 D4-
Metalized housing ALT A V+
V+
Data pair 1, plus pole, bidirectional Data pair 1, minus pole, bidirectional Data pair 2, plus pole, bidirectional V-
ALT B Data pair 3, plus pole, bidirectional Data pair 3, minus pole, bidirectional Data pair 2, minus pole, bidirectional V+
V+
V-
Data pair 4, plus pole, bidirectional Data pair 4, minus pole, bidirectional Internally AC coupled to FGND using a 100pF capacitor V-
V-
V+/- positive/negative pole of the PoE DC power input, Dx+/- Data line Caution: The earthing of the cable shield must be established on the feed side because there is internally NO low resistant DC connection provided between the connected cable shield and the Frame Ground of the device. Ethernet PoE IEEE 802.3-2012 Phantom power alternative A or B are supported for 100/100/1000 Base-T 47000001566-THb-02 Technical Manual | Roadside ITS Station RIS-9160-xx0x Page 25 of 36 System cable connection The system connector concept of the RIS-9160 ensures a stable and waterproof connection of the system cables with the device. To ensure this the cables have to be connected as described in this section. Preparation 1. Check if the Connector assembly parts according Table 7 are complete. Cable gland fitting with original gasket inserted Material:
Polyamide Key width SW:
29mm Inner Diameter: max. 17mm Cable gland - cap nut Material:
Polyamide Key width SW:
29mm Inner Diameter: max. 17mm Rubber gasket size A Material:
EPDM Cable Diameter: STP 7,0-9,0 mm Rubber gasket size B Material:
EPDM Cable Diameter: STP 4,0-6,5 mm Table 7 Connector assembly parts 2. Remove the original gasket out of the cable gland fitting according Figure 10. 47000001566-THb-02 Page 26 of 36 Technical Manual | Roadside ITS Station RIS-9160-xx0x Remove the original gasket Figure 10 Remove original gasket 3. Check if the Sealing is placed correctly on the fitting according Figure 11 Figure 11 Position of the sealing Sealing 4. Prepare the correct size A or size B of the rubber gasket depending on the cable diameter. 5. Push the cable carefully through the cap nut and cable gland fitting according Figure 12. Ensure that the locking mechanism remains intact. 6. Attach the appropriate rubber gasket size A or size B depending on the cable diameter according Figure 12 so that the profiled side of the gasket is oriented towards the fitting !
Sealing 12 Cable Connection Figure Mounting Details RJ45 connector with locking mechanism Cable gland-fitting Rubber gasket Cap nut 47000001566-THb-02 Technical Manual | Roadside ITS Station RIS-9160-xx0x Page 27 of 36 Cable gland-fitting Rubber gasket Figure 13 Direction of the Rubber Gasket 7. Check the correct direction of the rubber gasket which is also shown in Figure 13 to ensure waterproofness of the connection !
8. Connect the RJ45 connector to the system connector of the RIS-9160 and ensure that the locking mechanism of the connector is fixed. 9. Attach the cable gland - fitting carefully to the threaded whole in the RIS-
9160, ensure that the thread fits smoothly and fasten the fitting with a torque of 10 Nm. 10. Slide the rubber gasket into the slot of the fitting. 11. Move the cap-nut across the fitting. 12. Fasten the cap-nut to the fitting with a torque of 4 Nm. Attention: Overpowering will irreversibly destroy the Polyamide thread!
Too less torque will not ensure rated IP Class. Figure 14 RIS-9160 with connected system cable 47000001566-THb-02 Page 28 of 36 Technical Manual | Roadside ITS Station RIS-9160-xx0x Mechanical Characteristics Electrical Characteristics and Conditions Product Specifications Dimensions [LxWxH]
without bracket 11.5 in x 7.9 in x 3.07 in
(290mm x 200mm x 78mm) Weight without bracket
<6.6 pounds (~3 kg) Material of housing Aluminum alloy die casting PoE/LAN system interface Rated Input Voltage PoE Nom. 48V DC (IEEE 802.3at) Input Voltage Range Min: 36V DC Max: 57V DC POE device classification Type 2, PoE+, max. 25.5 W over two pairs Supported POE power modes:
Mode A (via pins 1-2 / 3-6) Mode B (via pins 4-5 / 7-8) 4 pair mode Galvanic insulation 2250V AC for 1 minute Protection Internal Surge protection LAN Physical Interface 10/100/1000 BASE T Power consumption RIS-9160-1A0x 34034340xxx, Platform Specification 14W Processor 1,33 GHz, 64 Bit, INTEL ATOM E3825 dual-core Basic Memory config. 1GB RAM ECC / 4GB eMMC SLC Optional memory config Up to 8GB RAM ECC, up to 64 GB eMMC Operating System Linux SLC/MLC Optional SSD:
mSATA-SSD, iSLC, 6GB/s, 8-256 GB Optional SD card:
Micro SD up to 128GB RF Interfaces 5.9 Radio 1 Frequency range 5.860GHz - 5.920GHz Channels 172,174, 176,178,180,182,184 Channel Bandwidth Data Rates 10MHz 6MBit/s 47000001566-THb-02 Technical Manual | Roadside ITS Station RIS-9160-xx0x Page 29 of 36 Antenna Connector Type N female Output power 20dBm (CFR 47 Part 90 Class C) Output power Adjustment range 0dBm .. +20dBm in 1dB steps Receiver Sensitivity
-92dBm @ 6Mbps (typ.) ACR/NACR Enhanced GNNS Interface System support Multi GNSS Antenna Connector Type N female Antenna Type GPS Antenna, passive or active supply 3,3V for active antenna LED Interface Indications 1 x green LED (Power indication) 1 x 3-color LED (Status indication) 2 x 3-color LEDs (SW defined) Environmental Conditions Environmental Conditions Temperature (operation)
-40C ...+74C
-40 F +165,2 F This temperature range does not consider increase of temperature due to exposure to solar irradiation. Its mandatory to use the optional sun cover if the case temperature exceeds this limit due to solar irradiation. Temperature (storage)
-40C ...+85C
-40F 185F IEC protection rating Oscillation sinus
(operation) Oscillation random
(operation) Shock
(operation) MTBF NEMA 4X IP67 EN60068-2-6 Fc (2008-12) 1-9Hz 3,5mm 10-200Hz, 10 m/s2 EN60068-2-64 Fc (2008-12) 100-200Hz / -7dB/octave 200-2000Hz / 1m2/s3 10-100Hz / 5m2/s3 EN60068-2-27 Ea(2010-04) 150m/s / 6ms 100.000h according to BELLCORE TR-TSY-
000332 47000001566-THb-02 Page 30 of 36 Product Marking Technical Manual | Roadside ITS Station RIS-9160-xx0x FCC-ID: XZU9160
(FCC will be available after conclusion of certification / listing) 47000001566-THb-02 Technical Manual | Roadside ITS Station RIS-9160-xx0x Page 31 of 36 Mechanical Dimensions All dimensions are given in mm. Figure 15 Dimensions of RIS-9160 without mounting plate Figure 15 shows the dimensions of the RIS-9160-xxx0 device versions like part nr. 34034340001 without mounting plate where four M6 metrical screws are provided for mounting on the rearside of the device. Those screws are already premounted. in the factory. Figure 16 Dimensions of RIS-9160 with mounting plate M Figure 16 shows the dimensions of the RIS-9160-xxxM device versions with mounting plate M like part nr. 34034340000. 47000001566-THb-02 Page 32 of 36 Technical Manual | Roadside ITS Station RIS-9160-xx0x Figure 17 Dimensions of RIS-9160 with mounting adapter W Table 8 Standards Figure 17 shows the dimensions of the RIS-9160-xxxW device versions like part nr. 34034340002 with mounting adapter W. Conformity Standards Ref. Standard Description
[1]
IEEE 802.112012
[2]
IEEE 802.11p IEEE Standard for Information technology Telecommunications and information exchange between systems Local and metropolitan area networks Specific requirements Part 11: Wireless LAN Medium Access Control
(MAC) and Physical Layer (PHY) Specifications IEEE Standard for Information technology Telecommunications and information exchange between systems Local and metropolitan area networks Specific requirements Part 11: Wireless LAN Medium Access Control (MAC) and Physical Layer (PHY) Specifications Amendment 7: Wireless Access in Vehicular Environments 47000001566-THb-02 Technical Manual | Roadside ITS Station RIS-9160-xx0x Page 33 of 36 Ref. Standard Description
[3]
IEEE 1609.4 2016 Draft Standard for Wireless Access in Vehicular Environments (WAVE) Multi-channel Operation
[4]
IEEE 1609.3 2016 Draft Standard for Wireless Access in Vehicular Environments (WAVE) Networking Services
[5]
IEEE 1609.12 2016 Standard for Wireless Access in Vehicular
[6]
47 CFR Part 2
[7]
47 CFR Part 15
[9]
47 CFR Part 90 Environments (WAVE) Identifier Allocations Code of Federal Regulations, Title 47, Part 2
(47 CRF 2) Part 2 Frequency allocations and radio treaty matters; General rules and regulations Code of Federal Regulations, Title 47, Part 15
(47 CFR 15) Part 15 Radio Frequency Devices Code of Federal Regulations, Title 47, Part 90
(47 CRF 90) Part 90 Private Land Mobile Services
[10] NEMA Standards
(NEMA 250-2008) NEMA Standard for Enclosures for Electrical Equipment
[11]
IEC 62368-1
[11a]
IEC 60950-22
[12]
EN 302 571 V2.1.1
(2017-02) Audio/video, information and communication technology equipment Part 1: Safety requirements International Electrotechnical Com-mission Safety of Information Technology Equipment-
Part 22: Equipment installed outdoors Intelligent Transport Systems (ITS);
Radiocommunications equipment operating in the 5 855 MHz to 5 925 MHz frequency band;
Harmonised Standard covering the essential requirements of article 3.2 of Directive 2014/53/EU
[13]
EN 301 489-1 V2.2.0 ElectroMagnetic Compatibility (EMC) standard for radio equipment and services;
Part 1: Common technical requirements;
Harmonised Standard covering the essential requirements of article 3.1(b) of Directive 2014/53/EU and the essential requirements of article 6 of Directive 2014/30/EU
[14]
EN 301 489-3 V2.1.1 ElectroMagnetic Compatibility (EMC) standard for radio equipment and services;
Part 3: Specific conditions for Short-Range Devices (SRD) operating on frequencies between 9 kHz and 246 GHz;
Harmonised standard covering the essential requirements of article 3.1(b) of Directive 2014/53/EU 47000001566-THb-02 Page 34 of 36 Information on Conformity of Products Declaration Address Technical Manual | Roadside ITS Station RIS-9160-xx0x Ref. Standard
[15]
EN 62 311: 2008 Description Assessment of electronic and electrical equipment related to human exposure restrictions for electromagnetic fields (0 Hz -
300 GHz) Statement of Conformity The following information applies to the product listed in Table 1. Hereby, Kapsch TrafficCom AG declares that the products listed in this document are in compliance with the essential requirements and all other relevant provisions of Directive 2014/53/EU. The Declaration of Conformity https://www.kapsch.net/ktc/Portfolio/Products/RF-Field-Products/5-9-GHz-
WAVE-DSRC-Transceivers for download is available from For further information please contact us. Kapsch TrafficCom AGAm Europlatz 2 A-1120 Vienna Tel.: +43 (0)50 811 0 Email: ktc.info@kapsch.net 47000001566-THb-02 Technical Manual | Roadside ITS Station RIS-9160-xx0x Page 35 of 36 Optional Equipment Mounting Bracket for RIS-9160 The counterpart of the mounting plate M is the mounting bracket with locking, Kapsch part number 34017690200. Figure 18 Mounting Bracket with safety wire Figure 19 Dimensions and drilling plan of the Mounting Bracket Safety wire To protect the device from unintentionally slipping out of the mounting bracket it is secured with the Safety Wire. The Safety Wire itself is protected against loss or drop-down as it is attached to the bracket through additionally dedicated security holes. Material: Stainless steel Note: The outline of the safety wire can slightly differ from the shown one in Figure 18. 47000001566-THb-02 Page 36 of 36 Table 9 Protection caps and termination plugs Technical Manual | Roadside ITS Station RIS-9160-xx0x Protection caps and termination plugs The protection caps and the RF terminations are delivered depending on customer configuration and demand along with each RIS-9160 or can be ordered separately. Termination type Description Kapsch Part No. RF termination (50Ohm) 76000046410 RF termination plug, N male, 50R, 2W. Note: IP66 protection class only !
N-Connector protection cap, no RF termination, 130 Ncm rated torque. 76000066660 N connector protection cap M25x1,5 cap and sealing 76000066560 76000078180 Cap Sealing Note: The specified protection class of IP67 is only ensured when both cab and sealing are mounted !
47000001566-THb-02
frequency | equipment class | purpose | ||
---|---|---|---|---|
1 | 2018-06-04 | 5860 ~ 5920 | TNB - Licensed Non-Broadcast Station Transmitter | Original Equipment |
app s | Applicant Information | |||||
---|---|---|---|---|---|---|
1 | Effective |
2018-06-04
|
||||
1 | Applicant's complete, legal business name |
Kapsch Trafficcom AG
|
||||
1 | FCC Registration Number (FRN) |
0019389600
|
||||
1 | Physical Address |
am Europlatz 2
|
||||
1 |
VIENNA, 1120
|
|||||
1 |
Austria
|
|||||
app s | TCB Information | |||||
1 | TCB Application Email Address |
a******@tuv.at
|
||||
1 | TCB Scope |
B4: Microwave, Millimeter Wave Band and Citizens Broadband Radio Services equipment in 47 CFR Parts 25, 30, 74, 90, 95, 96, 97, 101 (all above 3 GHz)
|
||||
app s | FCC ID | |||||
1 | Grantee Code |
XZU
|
||||
1 | Equipment Product Code |
9160
|
||||
app s | Person at the applicant's address to receive grant or for contact | |||||
1 | Name |
T******** R******** G******
|
||||
1 | Title |
Dipl. Ing.
|
||||
1 | Telephone Number |
+4366********
|
||||
1 | Fax Number |
+4350********
|
||||
1 |
g******@kapsch.net
|
|||||
app s | Technical Contact | |||||
n/a | ||||||
app s | Non Technical Contact | |||||
n/a | ||||||
app s | Confidentiality (long or short term) | |||||
1 | Does this application include a request for confidentiality for any portion(s) of the data contained in this application pursuant to 47 CFR § 0.459 of the Commission Rules?: | Yes | ||||
1 | Long-Term Confidentiality Does this application include a request for confidentiality for any portion(s) of the data contained in this application pursuant to 47 CFR § 0.459 of the Commission Rules?: | No | ||||
if no date is supplied, the release date will be set to 45 calendar days past the date of grant. | ||||||
app s | Cognitive Radio & Software Defined Radio, Class, etc | |||||
1 | Is this application for software defined/cognitive radio authorization? | No | ||||
1 | Equipment Class | TNB - Licensed Non-Broadcast Station Transmitter | ||||
1 | Description of product as it is marketed: (NOTE: This text will appear below the equipment class on the grant) | ITS - DSRC Road Site Unit | ||||
1 | Related OET KnowledgeDataBase Inquiry: Is there a KDB inquiry associated with this application? | No | ||||
1 | Modular Equipment Type | Does not apply | ||||
1 | Purpose / Application is for | Original Equipment | ||||
1 | Composite Equipment: Is the equipment in this application a composite device subject to an additional equipment authorization? | No | ||||
1 | Related Equipment: Is the equipment in this application part of a system that operates with, or is marketed with, another device that requires an equipment authorization? | No | ||||
1 | Grant Comments | Power listed is EIRP. The antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons, and must not be co-located or operating in conjunction with other antennas or transmitters. End-users and installers must be provided with the antenna installation instructions and transmitter operating conditions for satisfying RF exposure compliance. This device supports 10 MHz bandwidth. | ||||
1 | Is there an equipment authorization waiver associated with this application? | No | ||||
1 | If there is an equipment authorization waiver associated with this application, has the associated waiver been approved and all information uploaded? | No | ||||
app s | Test Firm Name and Contact Information | |||||
1 | Firm Name |
TUV AUSTRIA SERVICES GMBH
|
||||
1 | Name |
W**** S********
|
||||
1 | Telephone Number |
43-1-********
|
||||
1 | Fax Number |
43-1-********
|
||||
1 |
e******@tuv.at
|
|||||
Equipment Specifications | |||||||||||||||||||||||||||||||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
Line | Rule Parts | Grant Notes | Lower Frequency | Upper Frequency | Power Output | Tolerance | Emission Designator | Microprocessor Number | |||||||||||||||||||||||||||||||||
1 | 1 | 90 | 5860.00000000 | 5920.00000000 | 0.5000000 | 4.2000000000 ppm | 10M0D7D |
some individual PII (Personally Identifiable Information) available on the public forms may be redacted, original source may include additional details
This product uses the FCC Data API but is not endorsed or certified by the FCC