FCC ID: 2AXFA-MINIVISION2 4G PHONE

User Manual 4G PHONE Model: MiniVision2 Getting Started Inserting a SIM card Remove

(opening left-hand corner) in the battery cover bottom the Slide the SIM card into the SIM card holder with gold contacts facing down. Slide your MicroSD card into the card holder with gold contacts facing down Inserting and battery Insert the battery, making sure that battery contacts touch the gold contacts, then place the battery cover and press down until it clicks into place. 2 Using the Phone In standby mode the phone is one, but is not running any applications (call, SMS message, etc.). Using the menu Press Left menu key to open the menu. Press Up/Down arrow keys to flick through the menu items. Press Left menu key to open a menu item. To return to standby mode, press Red button or close the phone. Dual-function keys Some keys have additional functions if they are pressed and held down for a few seconds. Number 1 key: Listen to mailbox.

# (Pound) key: Switch between normal mode and meeting (vibrate only) mode. Number 0 key: Torch on continuously when the phone is on. Saving Contacts to Phonebook 1. Press Options add contact OK 2. To input contacts name, use down arrow key to move the highlight to Name, then press Edit. Press OK when finish. 3. To input phone number, press the down arrow button to move the highlight to Mobile or Home number, press edit, press OK when finish. Please note: You can assign specific ringtone to each contact. Simply move the highlight to Default ringtone, press Edit then select ringtone from Phone ringtones or your own sound files. 4 Camera Camera (take photos) Note: To get sharp photos, wipe the lens clean with a dry cloth. 1. Press shortcut camera Alternatively Menu->Multimedia->Camera. button. press 2. Press Camera button to take photo. 3. After the photo was taken, press Options to Delete, Set as wallpaper or go to Image viewer for more options. Note: To store more pictures you need a micro SD memory card up to 16 GB. (Not included in the accessories) Camera adjustiment 1. Use Up/down navigation arrow keys to zoom in and out. 2. Use the * button and # button to adjust 5 EV/light sensitivity. Note: Zoom may reduce picture quality. Camera settings In camera, press Options, select Settings then press OK In this menu, you can change the quality of the photo, Banding, Shutter sound on/off, auto save on /off and change the preferred storage to save the photos between Phone or micrSD card (not supplied with accessories) 1. 2. 6 Messages You can send and receive messages. however, it may depend on your network operator. Please contact your network operator for more information. Write messages 1. Select Menu, Messages and press OK 2. Press Write message, choose New SMS

(text message) or New MMS (multimedia message) Note: For MMS test message, extra service charge may apply depends on your cellular service plan, please contact your cellular carrier for details) Text input The following functions are available:

Press the * Button to choose some 7 special character Press the # Button to switch between small, and word recognition. The icon display on the top right of the display. capitalization Press the right and left key to change the place Press the right menu button to delete. Press and hold right menu button to delete all letters. Input methods are:

En: T9 Predictive, first letter cap then small letter En: T9 Predictive, all small letter EN: T9 Predictive, all cap letter Abc: Corresponing keys once per letter, 8 first letter cap then small letter abc: Corresponing keys once per letter, all small letter ABC: Corresponing keys once per letter, all cap letter 123: All number input After you the message is complete, press Options and select Send The phone has the possibility that Send to one or multiple contacts. Other options:

You can see limit of the number of written letters on the right top of the screen. Inbox In this menu you can read new or already 9 read messages. Depending on the mode, the phone vibrates or rings and the Green LED will flash if you get a new messages in standby mode, you can also see this icon on the screen. Press the Option for following functions:

Delete, Reply, Call sender, Forward, Advanced and Save. Note: If the message memory is full, flashes in standby mode, please delete some messages to reveive new ones. In Draft you will see your saved SMS messages. Drafts Outbox Sent In Outbox store unsent messages. 10 In this menu you can see already sent messages. The following functions are available:

View, Delete, Delete all, Forward, Mark and Sort. Calls history In this menu option, Your phone stores list for Missed calls, dialed calls and received calls. Note: The latest entries are on the top of the list. You can also delete all call history by pressing OK on 4th option Delete all Call time information about the Last call, Received timers provides you the 11 calls, Dialled calls, and Entire call history. Organizer Alarm clock Up to 3 alarm clocks can be made. To set the alarm:

1. Select an alarm and press Edit. You can set the alarm with follow options:

Status on/off (Press Camera button to confirm), Time, Repeat as well as the Alarm tone. 2. After the alarm clock is set, press button Save. 3. When the alarm sounds, press Stop or Snooze button to stop the alarm. If the alarm was snoozed, it will sound 12 the alarm again in 5 minutes. Calculator With this function, you can use your mobile phone as a calculator. The Calculator controls the basic arithmetic functions. Features:

Type the number (1 to 0). Press # for a decimal point. Use the arrow keys for: +, -

Use the M1 M2 keys for: x, Press Camera button for: =

Press right menu button for delete Calendar 1. Select Calendar and press OK Press down arrow, up arrow, M1 and M2 13 Keys in the calendar navigate the date. By pressing the left menu button

(Options), you can Add new schedule, View schedule, check all schedules, Clear todays schedule and Clear all Schedules. 1. SOS Setting up the SOS function How does SOS function work?

Caution: When an SOS call is activated the to handfree/speakerphone mode. Do not hold the device near your ear when the pre-set phone is 14 speakerphone mode is in use, because the volume maybe extremely loud. 1. Press the Left Menu key (on keypad) 2. Scroll to and select Tools 3. Go through to Number Setting-Emergency NumberSave 4. Go through Emergency SMS-write message Please note: SOS message will only be sent to mobile phone numbers (in SOS list). SOS calls need to be accepted by the receiver within a specific timeframe. If you are programming a phone number that has an automatic answering feature please test before use. Meeting (Vibrate only) mode When in standby mode, the phone can be 15 changed to meeting (Vibrate only) mode by pressing and holding the pound (#) key for three seconds. Repeat the step will switch the phone back to normal mode. Setting 1 Sim card 2 Wi-fi Press Wifiselect on -Option-

search the Net workwrite the code 3 Bluetooth Active Bluetooth 1. Press Menu->Organizer->Bluetooth then press OK 16 2. Select 1st option Bluetooth then press ON Important note: When you are not using Bluetooth connectivity, select Bluetooth off. Do not pair with an unknow device. 4, Audio profiles Profiles (sound) Press Menu->Settings->Profiles then OK Important note: To activate the speaking keypad feature, please select Human voice profile, press Options and Activate. Display the profile mode list including:

General, silent, meeting, Human voice and outdoor. Select the mode and press Option will enable following options. Activate: To activate the selected Profile Add: To add setting options to the seleted 17 profiles Settings: Adjust ringer, keypad sounds, and other desired sounds etc. 5 Display U can choose the light of t he phone here,also the font size 6 Voice abroadcast 7 Data usage U can find the memory of the phone here 8 Personal 8.1 Location 18 8.2 security 8.3 Date & time 8.4 Language & input 8.5 Scheduled on/off 9 system 9.1 Storage 9.2 Battery 9.3 Mouse control 9.4 Apps 19 9.5 Reset 9.6 About the phone 20 FCC Statement This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction. 21 Specific Absorption Rate (SAR) information:

This device meets the government's requirements for exposure to radio waves. The guidelines are based on standards that were developed by independent scientific organizations through periodic and thorough evaluation of scientific studies. The standards include a substantial safety margin designed to assure the safety of all persons regardless of age or health. FCC RF Exposure Information and Statement the SAR limit of USA (FCC) is 1.6 W/kg averaged over one gram of tissue. Device types: This device has also been tested against this SAR limit. This device was tested for typical body-worn operations with the back of the phone kept 10mm from the body. To maintain compliance with FCC RF exposure requirements, use accessories that maintain an 10mm separation distance between the user's body and the back of the phone. The use of belt clips, holsters and similar accessories should not contain metallic components in its assembly. The use of accessories that do not satisfy these requirements may not comply with FCC RF exposure requirements, and should be avoided. 22

SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: 2AXFA-MINIVISION2 Label and Location 4G PHONE Model No: MiniVision2 FCC ID: 2AXFA-MINIVISION2 Size: L: 3cm*W: 2cm Label Location This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd. Page 1 of 1

KAPSYS Agent Authorization Company: KAPSYS Address: 694, Avenue Maurice Donat, 06250, Mougins, France Product Name: 4G PHONE Trade Mark: KAPSYS Model Number: MiniVision2, KAP04100, D210 FCC ID: 2AXFA-MINIVISION2 We authorize MiCOM Labs Inc., 575 Boulder Court, Pleasanton, California 94566, USA, to act on our behalf on all matters concerning the certification of above named equipment. We declare that MiCOM Labs Inc. is allowed to forward all information related to the approval and certification of equipment to the regulatory agencies as required and to discuss any issues concerning the approval application. Any and all acts carried out by MiCOM Labs on our behalf shall have the same effect as acts of our own. Signature:

Date: 2020-11-27 Name:

Laurent Delesalle Title:

Chief Operating officer Company: KAPSYS

KAPSYS Add: 694, Avenue Maurice Donat, 06250, Mougins, France Tel: +33 (0)6 74 23 76 43 Fax: +33 (0)4 92 28 88 89 Date: 2020-11-27 Dear Sir/Madam, We, KAPSYS Hereby declares the following statement , PCB board, circuit, structure and internal of these model(s) are the same, Only model numbers are different for marketing purpose:

Trade Mark: KAPSYS Product name: 4G PHONE Models No.: MiniVision2, KAP04100, D210 Sincerely, Clients name / title : Laurent Delesalle / Chief Operating officer Contact information / address: 694, Avenue Maurice Donat, 06250, Mougins, France Tel: +33 (0)6 74 23 76 43 Fax: +33 (0)4 92 28 88 89 E-Mail: laurent.delesalle@kapsys.com

KAPSYS Office of Engineering Technology Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 USA Date: 2020-11-27 Subject; Request for Confidentiality FCC ID: 2AXFA-MINIVISION2 To Whom It May Concern, Pursuant to the provisions of the Commissions rules Title 47 Sections 0.457 and 0.459, we are requesting the Commission to withhold the following attachment(s) as confidential documents from public disclosure indefinitely. These documents contain detailed system and equipment descriptions and are considered as proprietary information in operation of the equipment. The public disclosure of these documents might be harmful to our company and would give competitors an unfair advantage in the market. Schematic Diagram Block Diagram Operational Description Parts List Tune-up Procedure External Photos Test Setup Photos Internal Photos User Manual In additional to above mentioned documents, in order to comply with the marketing regulations in Title 47 CFR 2.803 and the importation rules in Title 47 CFR 2.1204, while ensuring that business sensitive information remains confidential until the actual marketing of newly authorized devices, we request Short Term Confidentiality of the following attachment(s);

OR For 45 days, pursuant to Public Notice DA 04-1705. For 180 days pursuant to KDB 726920 D01. It is our understanding that all measurement test reports, FCC ID label format and correspondence during the certification review process cannot be granted as confidential documents and this information will be available for public review once the grant of equipment authorization is issued. Sincerely, Signature:

Name: Laurent Delesalle Title: Chief Operating officer

WIFI Channel 12 and 13 Declaration Letter We declare the equipment identified below with regards to Channel 12 and 13 capabilities for KAPSYS FCC ID: 2AXFA-MINIVISION2 Declaration Product hardware does not have the capability to operate on Channel 12 and 13. Product hardware has the capability to operate on Channel 12 and 13. However, these two channels will be disabled via software and will not be accessible to user. Product hardware has the capability to operate on Channel 12 and 13. However, all the operated channels cant be changed in the RF parameter via software. All channels have complied with all of the requirements sets out in FCC Part 15.247. Product hardware has the capability to operate on WiFi Channel 12 and 13, and meets the requirements of KDB 594280 D01 v02r01. Please note:

1.) By default, this device operates in a mode that is compliant with the U.S. requirements. 2.) This device will also use supplemental information such as geo-location data to determine that it is operating outside the U.S., if necessary, to change its power. Such supplemental data will be derived from the following:

Global Navigation Satellite System (GNSS)7 sensors in the device Mobile Country Code (MCC),8 or MCC with a Mobile Network code (MNC), received from a CMRS9 carrier and received directly by a receiver on the device Country information derived from multiple adjacent access points (for example using IEEE Std 802.11d provisions) may be permitted on case-by-case basis Other suitable geo-location data based on IP addresses or other reliable source. Name / Title: Laurent Delesalle / Chief Operating officer Signature:

Tel: +33 (0)6 74 23 76 43 Email: laurent.delesalle@kapsys.com Date: 2020-11-27 Page 1 of 1 Rev.2.0