anl<o Thankou for choosing 42568568. We hope you enjoy using it. our Anko Bluetooth Headset B.Pairing 1.Once the headphone the headset with Bluetooth devices is powered on, it is in pairing chipset 10 meters hi-fi Bluetooth Time: >100 Hours d.c. V4.2 multimedia Profiles:
A2DP, AVRCP, HFP Distance:
Specifications:
Model No: 42568568 Version:
Support Working Music Time: >10 Hours Talk Time: >10 Hours Standby Charging Voltage: 5V Battery Capacity: 450mAh Charge Time: 4 Hours Cable Length:
1.1m Pairing Non-Play automatic the headphone automatically alarm sounds. Security will enter power save mode and then off when the low battery Window Time: 5 minutes Code: 0000 switch off window time: after 30 seconds 32.5mm Included:
1.Bluetooth Headphone 2.Charging Cable 3.Audio cable (3.5mm jack cable) J/I Overview:
1.Play / Phone button 2.Power button 3.LED indicator 4.Built-in 5./V+ Button:
6./V-Button:
7.Charging 8.Headphone port microphone cable socket next song and volume previous song and volume down up mode (blue & red LED flashes last paired
(if available) quickly) and will pair to device 2.Pair the headset in Bluetooth menu in media device you can hear a pairing tone and and once it is paired, LED stays on constantly. The when playing media. PLUM) HEADPHONE
(Bluetooth name: ANKO Blue LED flashes slowly C.Phone calls 1.Please phone calls. press':1/
i"button to pick up/hanging up 2.Double press the':1/1"button to call the previous number dialed. D.Playing music with the media device the headset you can enjoy music through you can connect alternatively When the headset connects Bluetooth wirelessly, headphone connected headphone the headphones cable and listen directly input. to your media device via its can still This function battery is flat. the braided to music when the cable is via be used when Function Pause Pla!::J Next Song Previous Volume Song Up
" "button
" "button Operation Short press "J/11>11"
button Short press "J/11>11" button Short press Short press Long press" V+" button
-when the volume to maximum you will hear a voice indication tone Long press "v-" button is adjusted Volume Down Charge:
Battery This Bluetooth battery. Please the battery. headset use the accessory by rechargeable USB cable to recharge is powered Li-ion USB charging cable into 1.Insert 2.Connect 3.Indicator 4.Indicator 5.It takes about 4 hours to fully charging the headset LED turns Red to show battery LED turns off when battery is fully the battery. USB port. USB port (7). is charging. cable with a suitable charged. charge How to use this headset:
A.Power On/ Off
`
i i i 5 6 Function Operation Indicator LED Power On Press and hold the power Red and Blue LED button for 3 seconds blink alternatively Power Off Press and hold the power Red LED flashes button for 3 seconds then goes out
/
1 2
}
1
. 3 4?4 if battery CAUTION
> Danger of explosion Replaceonly with same or equivalent_
> Attention
> The use of apparatus
> The batteries in moderate shall not be exposed climates. to excessive is incorrectly be drawn to the environmental aspect replaced. should type. of battery disposal. heat such as sunshine, please of unit in fire or water.Neverattempt WARNINGDonot dispose household of children 0C or above 45C).Extremetemperatures device to get wet-liquids recycle Small parts may cause choking waste, and animals. or serious can cause deforming damage. Waste electrical for recycle advice. Check with your local authority Avoidexposing injuyif swallowed. of the device and reduce the charging your device capacity Do not handle your device with wet hands. wheefacilities exist. can cause serious should not be disposed
> Keep your device and all accessories products of with out of the reach to very cold or very hot temperatures
(below and life of your device. Donot allow your mark and logos are registered fire or the like. any use of such marks by KMART AUSTRALIA The Bluetoothword I and reassemble. to disassemble trademarks is under licence. owned by Bluetooth SIG, Inc., and FCC ID2AQYH-BT-42568568 This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:(1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.