SD 2.0 Wireless Radio User Guide Version 1.0 12/6/13 Copyright 2013 KCF Technologies, Inc. All rights reserved KCF Technologies, Inc. | 336 South Fraser Street, State College PA 16803 | 814.867.4097 | www.kcftech.com Revision History Revision Date 1.0 12/6/13 Note
--
Table of Contents General Description Performance Specifications Physical Dimensions FCC Compliance Information 2 | K C F T e c h n o l o g i e s S D 2 . 0 W i r e l e s s R a d i o U s e r G u i d e 3 4 5 6 General Description The SD 2.0 Wireless Radio is a 2.4 GHz 2-way radio module intended for wireless transmission of sensor data. The boards small package and modular design facilitate integration with a wide range of sensors, and in particular it is designed to be permanently mounted to KCFs line of Smart Diagnostics sensors. The radio features a proprietary multi-frequency network protocol to allow simple setup and operation of up to 100 sensor nodes per receiver, making it an ideal solution for multi-point monitoring of industrial equipment. The communication protocol of the radio is highly configurable to allow tailoring of data collection to numerous different applications. Sampling rate, collection interval, input channels, etc. are all adjustable by the user. The radio is designed to be attached via land-grid-array (LGA) soldering to the sensor board it is serving, thereby minimizing the size of the entire sensor/radio package and eliminating the size, expense, and long term reliability risks of a connector. The radio is powered via the LGA connection to the sensor board. The radio communicates using an antenna provided by KCF which attaches to the radio module using a standard U.FL connector. 3 | K C F T e c h n o l o g i e s S D 2 . 0 W i r e l e s s R a d i o U s e r G u i d e Performance Specifications Wireless Module RF Frequency Band Data rates Modulation Channel spacing Receive sensitivity Acknowledgement Retransmission Microcontroller Digital I/O ADC inputs RAM Flash Physical Mass Mount Antenna port Temperature RoHS Voltage Programming interface Certification FCC/ETIS 2.4 GHz ISM band 2000 kbps GFSK 6 MHz
-90 dB at 2000 kbps Hardware level auto-acknowledgement Hardware level 0-35x 47 10 external - 12 bit SAR 10k 128k 3.5 grams LGA Hirose U.FL
-40 to+ 85C Compliant 2.7-3.6 V (Recommend Duracell CR123A Battery) Spy-Bi-Wire (serialized JTAG) Pending 4 | K C F T e c h n o l o g i e s S D 2 . 0 W i r e l e s s R a d i o U s e r G u i d e Physical Dimensions Note: Dimensions in inches, tolerance is +/- 0.010 5 | K C F T e c h n o l o g i e s S D 2 . 0 W i r e l e s s R a d i o U s e r G u i d e FCC Compliance Information FCC ID: Z5ISD2 This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications to this device (including operating at different power levels or substituting a different antenna) not expressly approved by KCF Technologies, Inc. may void the users authority to operate this equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna. Connect the equipment into an outlet on a circuit different from that to which the Increase the separation between the equipment and receiver. receiver is connected. Consult the dealer or an experienced radio/TV technician for help. CAUTION: to minimize RF exposure it is recommended to maintain a minimum separation of 20cm between the device and the user during operation. 6 | K C F T e c h n o l o g i e s S D 2 . 0 W i r e l e s s R a d i o U s e r G u i d e