Issue department:Bedding Division
Product Function
instruction
MC232
Date:
Author:
2021-06-26
Kyle
No:
Version:
1.1
Page 1 of 4
MC232 Function instruction
1. Electrical configuration diagram:
1
Issue department:Bedding Division
Product Function
instruction
MC232
Date:
Author:
2021-06-26
Kyle
No:
Version:
1.1
Page 2 of 4
2. Function Picture
1. Process of test
1.1. HEAD port
Connect to head actuator,control by remote single:
Click head up button on the remote, head actuator moves out, stop when released;
Click head down button,head actuator moves in, stop when released;
This function takes effect only by pressing the corresponding button on the remote.
1.2. FOOT port
Connect to foot actuator,control by remote single:
Click foot up button,foot actuator moves out,stop when released;
Click foot down button,foot actuator moves in,stop when released;
This function takes effect only by pressing the corresponding button on the remote.
2
Issue department:Bedding Division
Product Function
instruction
MC232
Date:
Author:
2021-06-26
Kyle
No:
Version:
1.1
Page 3 of 4
1.3. Massage
Connect to head massage,control by remote:
Click head massage + button,head massage strengthens by one level;
Click head massage - button,head massage weakenby one level;
This function takes effect only by pressing the corresponding button on the remote.
1.4. MULTIFUNCTION port
Connect with the same other Control box or Other accessories;
1.5. Power LED & PAIRING LED
Power supply for control box, PAIRING LED of control box flashes for 4 times,and then turns off, POWER LED turns
on。
1.6. Power
Connect to the 29V DC;
1.7. Pair Function
Power up control box,pairing LED will be flash,the control box enters into mode of code paring;
Press and hold the paring LED of Remote, the backlight of paring LED flashes, the backlight of remote flashes, the
remote enters into mode of code paring;
The backlight of paring LED of remote stops flashing, and the paring led of control box stop flash, it indicates that
the code paring is successful;
If fails, repeat all the processes above;
1.8. FLAT function
Press and release the FLAT button on remote,the head and foot actuators moves to lower position(when the
actuator is free, can turn off the vibration motor and turn off the indicator light when press once ),stop when
press any buton;
3
Issue department:Bedding Division
Product Function
instruction
MC232
Date:
Author:
2021-06-26
Kyle
No:
Version:
1.1
Page 4 of 4
This function takes effect only by pressing the corresponding button on the remote.
1.9. ZERO G position function
Press and release ZERO G button on remote,the head and foot actuator moves to preset memory position,stop
when press any button;
This function takes effect only by pressing the corresponding button on the remote.
FCC Warning:
Please take attention that changes or modification not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause undesired operation.
ISED RSS Warning:
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject
to the following two conditions:
(1)
(2)
operation of the device.
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils
radioexempts de licence. L'exploitation est autorisée aux deux conditions suivantes :
(1)
(2)
brouillage est susceptible d'en compromettre le fonctionnement.
l'appareil ne doit pas produire de brouillage, et
l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le
this device may not cause interference, and
this device must accept any interference, including interference that may cause undesired
4