Issue departmentBedding Division Product Function instruction MC242 Date Author 2021-10-11 BenYang NoMC242 Version 1.1 Page 1 of 5 User Manual of MC242 1. Electrical configuration diagram 1 Issue departmentBedding Division Product Function instruction MC242 Date Author 2021-10-11 BenYang NoMC242 Version 1.1 Page 2 of 5 2. Function Picture 1. Process of test 1.1. HEAD MOTOR Connect to head actuator,control by remote single:
Click head up button on the remote, head actuator moves out, stop when released Click head down buttonhead actuator moves in, stop when released This function takes effect only by pressing the corresponding button on the remote. 1.2. FOOT MOTOR Connect to foot actuator,control by remote single:
Click foot up buttonfoot actuator moves outstop when released Click foot down buttonfoot actuator moves instop when released This function takes effect only by pressing the corresponding button on the remote. 2 Issue departmentBedding Division Product Function instruction MC242 Date Author 2021-10-11 BenYang NoMC242 Version 1.1 Page 3 of 5 1.3. TILT and Lumbar MOTOR Connect to TILT and Lumbar actuator,control by remote single:
Click bed up buttonTILT and Lumbar actuator moves outstop when released Click bed down buttonTILT and Lumbar actuator moves instop when released This function takes effect only by pressing the corresponding button on the remote. 1.4. Massage Connect to Foot and Head vibrator,control by remote single:
Click ALL Massage button, Foot and Head vibrator work,and click again,the strength enhance,there is 3 degree all. 1.5. SYNC port Connect with the same other Control box or Other accessories;
1.6. Power LED & PAIRING LED Power supply for control box, PAIRING LED of control box is blue, POWER LED is green 1.7. Power Connect to the 29V DC;
1.8. RESET button 1.9. Pair Function Press and hold the RESET buttonthe Head, Foot actuators will moves to lower position. Once power on pairing LED turns onthe control box enters into mode of code paring Press and hold the paring LED of Remote, the backlight of paring LED flashes, the backlight of remote flashes, the remote enters into mode of code paring;
3 Issue departmentBedding Division Product Function instruction MC242 Date Author 2021-10-11 BenYang NoMC242 Version 1.1 Page 4 of 5 The backlight of paring LED of remote stops flashing, and the paring led of control box turns off, it indicates that the code paring is successful;
If fails, repeat all the processes above;
1.10. FLAT function Press and release the FLAT button on remotethe head and foot actuators moves to lower position(when the actuator is free, can turn off the vibration motor and turn off the indicator light when press once )stop when press any buton This function takes effect only by pressing the corresponding button on the remote. 1.11. ZERO G position function Press and release ZERO G button on remotethe head and foot actuator moves to preset memory positionstop when press any button This function takes effect only by pressing the corresponding button on the remote. FCC Any C hanges or m odifications not e xpressly a pproved b y t he pa rty r esponsible f or c ompliance could void the users authority to operate the equipment. This de vice c omplies w ith part 15 of t he FCC R ules. Operation i s s ubject t o t he f ollowing t wo conditions: (1) T his d evice may n ot cau se h armful interference, an d (2) this d evice must accep t any interference received, including interference that may cause undesired operation. 4 This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help. FCC RF Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. ISED RSS Warning:
This device complies with Innovation,Science and Economic Development Canada licenceexempt RSS standard(s). Operation is subject to the following t wo c onditions: (1) this device may not cause i nterference, and (2) this de vice m ust accept any interference, i ncluding interference t hat may cause undesired operation of the device. Le pr sent appa reil es t con forme aux C NR d' ISED a pplicables aux appareils r adioexempts de licence. L'exploitation est autorise aux deux conditions suivantes:
(1) l'appareil ne doit pas produire de brouillage, et
(2) l'utilisateur de l'appareil doit accepter tout brouillage radiolectrique subi, mme s i le brouillage est susceptible d'en compromettre le fonctionnement. ISED RF exposure statement:
This equipment complies with ISED radiation exposure limits set forth for an uncontrolled environment.The device has been evaluated to meet general RF exposure requirement. Le matriel est conforme aux limites de dose d'exposition aux rayonnements noncs pour fac un autre environnement.ce dispositif a t valu satisfaire l'exigence gnrale de l'exposition aux rf. 5