Issue DepartmentBedding Division System Instruction Date 2022-03-25 Author Instruction of RF510A Edition 1.0 Page 1 of 5 Instruction of RF510A Figure 1 button ofremote 1 / 5 Issue DepartmentBedding Division System Instruction Date 2022-03-25 Author Instruction of RF510A Edition 1.0 Page 2 of 5 Click the Child Lock button for 3 second to lock or unlock the remote. Click the bed lamp button to open or shut the light under the bed. Item 1.1 Child Lock 18 1.2 Bed lamp 7 1.3 Antisnore 16 1.4 TV 15 1.7 M1 20 1.8 HEAD UP 1 1.10 HEAD DOWN 2 Click the Antisnore button, the bed moves to Antisnore position, press and hold Antisnore button for 5s, until backlight flashes, the control set the current position as Antisnore position Click the TV button, the bed moves to TV position, press and hold TV button for 5s, until backlight flashes, the control set the current position as TV position. Press head and foot up button, head and foot actuator moves out, stop when released. 1.5 HEAD AND FOOT UP 5 1.6 HEAD AND FOOT DOWN 6 Press head and foot down button, head and foot actuator moves in, stop when released. Click the M1 button, the bed moves to M1 position, press and hold M1 button for 5s until backlight flashes, the control set the current position as M1 position Press and hold HEAD UP button, head actuator moves out, stop when released. Press and hold HEAD DOWN button, head actuator moves in, stop when released. 2 / 5 Issue DepartmentBedding Division System Instruction Date 2022-03-25 Author Instruction of RF510A Edition 1.0 Page 3 of 5 Press and hold FOOT UP button,foot actuator moves out, stop when released. Press and hold FOOT DOWN button, foot actuator moves in, stop when released. 1.11 FOOT UP 3 1.12 FOOT DOWN 4 1.13 ZG 17 Click the ZG button, the bed moves to zeroG position, press and hold zeroG button for 5s, until backlight flashes, the control set the current position as zeroG position 1.14 HEAD MASSAGE 9,10 Click the HEAD MASSAGE button, head massage motor switches massage intensity, massage intensityswitches among 0-1-2-3 1.15 MASSAGE model 14 Click the MASSAGE MODEL button to change the massage model. 1.16 FOOT MASSAGE 11,12 Click the FOOT MASSAGE button, foot massage motor switches massage intensity, massage intensityswitches among 0-1-2-3 Click the MASSAGE TIME button to set the maassage time among 0-10-20-30mins. 1.17 MASSAGE TIME 13 1.18 FLAT 19 Click the FLAT button, the bed goes flat. 1.19 FLASHLIGHT 8 Click the FLASHLIGHT button to open and shut the Flashlight. 3 / 5 Issue DepartmentBedding Division System Instruction Date 2022-03-25 Author Instruction of RF510A Edition 1.0 Page 4 of 5 FCC warning Federal Communications Commission Statement This device complies with FCC Rules Part 15. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a class B digital device, pursuant to Part 15 of the Federal Communications Commission (FCC) rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment causes harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by doing one or more of the following measures:
Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. FCC Caution Any changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. The antenna(s) used for this transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. End users must follow the specific operating instructions for satisfying RF exposure compliance. To maintain compliance with FCC exposure compliance requirement, please follow operation instruction as documented in this manual. 4 / 5 Issue DepartmentBedding Division System Instruction Date 2022-03-25 Author Instruction of RF510A Edition 1.0 Page 5 of 5 This equipment complies with ISED radiation exposure limits set forth for an uncontrolled environment. End users must follow the specific operating instructions for satisfying RF exposure compliance. To maintain compliance with ISED exposure compliance requirement, please follow operation instruction as documented in this manual. Cet quipement est conforme aux limites d'exposition aux rayonnements ISED tablies pour un environnement non contrl. Les utilisateurs finaux doivent suivre les instructions d'utilisation spcifiques pour satisfaire la conformit d'exposition RF. Pour maintenir la conformit aux exigences de conformit d'exposition ISED, veuillez suivre les instructions d'utilisation comme document dans ce manuel. ISED RSS Warning:
This device complies with Innovation,Science and Economic Development Canada licenceexempt RSS standard(s). Operation is subject to the following two conditions:
(1) this device may not cause interference, and
(2) this device must accept any interference, including interference that may cause undesired operation of the device. Le prsent appareil est conforme aux CNR d'ISED applicables aux appareils radioexempts de licence. L'exploitation est autorise aux deux conditions suivantes:
(1) l'appareil ne doit pas produire de brouillage, et
(2) l'utilisateur de l'appareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible d'en compromettre le fonctionnement. 5 / 5