California Arch User Guide 1.Appearance 2.Specification 1. Part Number: JLDK.33.01.02;
2. Working Voltage3.0-5.0V;
3. Working Current21.8mA @4.5V;
4. Operation Temperature-2055;
5. Storage temperature-2575;
6. RF Frequency Range2.4~2.4835GHz;
7. RF ModulationGFSK;
8. RF Transmitted Power: 0 dBm;
9. Housing Material: ABS;
3.Interface Description P1 P2 P3 P4 P5 P6 P7 P8 P9 P10 P11 P12 P13 HEADMASSAGE TIMER FOOTMASSAGE HEADUP ZEROG FOOTUP HEADDOWN LIGHT FOOTDOWN MEMORYI MEMORYII MEMORYIII FLAT 1. P1(HEADMASSAGE)Turns head massage on and cycles trough all massage levels form lowest to highest. Turns head massage off if highest massage level was selected before button was pressed. 2. P2 (TIMER)Sets massage timeout. Cycles trough a timeout of 10, 20 and 30 minutes, starting with 10 minutes. Massage is turned off if massage timeout was set to 30 minutes before button was pressed. 3. P3(FOOTMASSAGE)Turns foot massage on and cycles trough all massage levels form lowest to highest. Turns foot massage off if highest massage level was selected before button was pressed. 4. P4(HEADUP)Press this key, the head actuator out, release to stop it. 5. P5 (ZEROG) Actuators are moved into ZERO G position automatically. The movement starts when the key is released. Click any key to stop it. 6. P6(FOOTUP)Press this key, the foot actuator out, release to stop it. 7. P7(HEADDOWN)Press this key, the head actuator in, release to stop it. 8. P8(LIGHT)Toggles on or off the floor light. 9. P9(FOOTDOWN)Press this key, the foot actuator in, release to stop it. 10. P10(MEMORYI)Actuators are moved into MEMORY I position automatically. The movement starts when the key is released. Click any key to stop it. If the key is pressed for more than 5 seconds the current position will be stored on this key. 11. P11(MEMORYII)Actuators are moved into MEMORYII position automatically. The movement starts when the key is released. Click any key to stop it. If the key is pressed for more than 5 seconds the current position will be stored on this key. 12. P12(MEMORYIII)Actuators are moved into MEMORYIII position automatically. The movement starts when the key is released. Click any key to stop it. If the key is pressed for more than 5 seconds the current position will be stored on this key. 13. P13(FLAT)Actuators are moved intoFLAT automatically. The movement starts when the key is released. Click any key to stop it. 14. P13&P5 (FLAT&ZERO G): Memory positions( I II III ) can be restored by pressing Zero-G and All-Flat for 5 seconds. 15. P4&P6&P7&P9(HEADUP&HEADDOWN&FOOTUP&FOOTDOWN):Press P4,P6,P7,P9 simultaneously, the control box will enter self-test mode;
4.Operation Instructions Pairing: There is a white key under the battery cover. Press this key for more than 1 second, the remote will enter pairing mode and a LED besides the pairing key will be flashing. Release this key to stop pairing .After the pairing is successful, LED will stop flashing. 5.Fcc warning This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.