| all | frequencies |
|
exhibits | applications |
|---|---|---|---|---|
| manual |
| app s | submitted / available | |||||||
|---|---|---|---|---|---|---|---|---|
| 1 |
|
User Manual | Users Manual | 1.28 MiB | November 01 2018 | |||
| 1 | Cover Letter(s) | November 01 2018 | ||||||
| 1 | External Photos | November 01 2018 | ||||||
| 1 | Internal Photos | November 01 2018 | ||||||
| 1 | ID Label/Location Info | November 01 2018 | ||||||
| 1 | ID Label/Location Info | November 01 2018 | ||||||
| 1 | Cover Letter(s) | November 01 2018 | ||||||
| 1 | RF Exposure Info | November 01 2018 | ||||||
| 1 | Test Report | / November 01 2018 | ||||||
| 1 | Test Setup Photos | November 01 2018 | ||||||
| 1 | Parts List/Tune Up Info | November 01 2018 |
| 1 | User Manual | Users Manual | 1.28 MiB | November 01 2018 |
SharpEyeTM SCV & SxV X-Band Radome Radar INSTALLATION, TERMINATION &
MAINTENANCE HANDBOOK KH-1650-CA Issue 1 SITUATIONAL AWARENESS, THE WORLD OVER SharpEye SCV & SxV X-Band Radome Radar Chapter 1: Contents DOCUMENT HISTORY Issue number Release date 13th July 2017 1 Details Handbook generated from Issue 4 of KH-1650 French translations of the Health & Safety section added. AMENDMENT RECORD When an amendment is incorporated into this handbook, the details should be recorded below. Amendment number Date inserted
(DD-MM-YYYY) Initials Details Copyright Kelvin Hughes Limited (2017) all rights reserved No parts of this publication may be reproduced, transmitted, transcribed, translated or stored in any form or by any means without the written permission of Kelvin Hughes Limited Technical details contained in this publication are subject to change without notice Where translated, the original English version of this document will remain the definitive document and should be referred to in any situation of doubt, confusion or conflict When planning any aspect of installation, commissioning, operation or maintenance of the system(s) described in this handbook, it is the responsibility of the individual carrying out the required task to ensure they are working from the latest issue/ revision of the document Printed copies of this handbook are not maintained KH-1650-CA issue 1 Page 2 of 60 SharpEye SCV & SxV X-Band Radome Radar Chapter 1: Contents 1 Contents 1 Contents ......................................................................................................................................... 3 2 Health and safety (Recommandations sanitaires et de scurit) ............................................ 5 3 4 5 Introduction ................................................................................................................................. 11 System overview ................................................................................................................... 11 Display interfacing ................................................................................................................. 12 Typical systems ..................................................................................................................... 12 3.1 3.2 3.3 Positioning of radar equipment ................................................................................................. 15 Preparation for installation ........................................................................................................ 19 Pre-Installation requirements ................................................................................................ 19 Fitting kits .............................................................................................................................. 20 Location ................................................................................................................................. 21 Lifting considerations ............................................................................................................ 21 5.1 5.2 5.3 5.4 6 Mechanical installation ............................................................................................................... 23 6.1 Mounting platform ................................................................................................................. 23 Anti-vibration mount/ Cable bracket assembly ...................................................................... 24 6.2 6.3 Installation ............................................................................................................................. 27 DIMENSIONS: SCV .............................................................................................................. 28 6.4 6.5 DIMENSIONS: SxV ............................................................................................................... 29 7 Termination .................................................................................................................................. 31 Cabling and termination ........................................................................................................ 31 DC input ................................................................................................................................ 33 LAN input ............................................................................................................................... 35 Ground/ Earth cable .............................................................................................................. 36 CONNECTION DIAGRAM .................................................................................................... 38 7.1 7.2 7.3 7.4 7.5 8 Commissioning ........................................................................................................................... 39 Overview ............................................................................................................................... 39 Commission web page .......................................................................................................... 40 Compass Settings ................................................................................................................. 41 Blind sector, heading line offset record ................................................................................. 42 8.1 8.2 8.3 8.4 9 Completion of installation .......................................................................................................... 43 9.1 Installation checks ................................................................................................................. 43 9.2 Warranty ................................................................................................................................ 44 10 Operator instructions ................................................................................................................. 45 10.1 Switch ON and OFF .............................................................................................................. 45 10.2 Control ................................................................................................................................... 45 10.3 Elevation beamwidth ............................................................................................................. 45 10.4 Performance monitoring ........................................................................................................ 45 10.5 Operational states ................................................................................................................. 46 KH-1650-CA issue 1 Page 3 of 60 SharpEye SCV & SxV X-Band Radome Radar Chapter 1: Contents 11 Planned maintenance ................................................................................................................. 49 12 Corrective maintenance ............................................................................................................. 53 12.1 System reset ......................................................................................................................... 53 12.2 Repair and return .................................................................................................................. 53 12.3 Troubleshooting .................................................................................................................... 54 13 Specifications .............................................................................................................................. 55 13.1 Mechanical specifications ..................................................................................................... 55 13.2 Environmental specifications ................................................................................................. 55 13.3 Transceiver specifications ..................................................................................................... 56 13.4 Approvals .............................................................................................................................. 57 14 Contact details............................................................................................................................. 59 KH-1650-CA issue 1 Page 4 of 60 SharpEye SCV & SxV X-Band Radome Radar Chapter 2: Health and safety (Recommandations sanitaires et de scurit) Health and safety (Recommandations sanitaires et de scurit) 2 When working on Kelvin Hughes equipment, operators and engineers are expected to work within the Health and Safety guidelines noted in this handbook, as issued by their respective employer or as stated by site regulations, shipyard or the vessel owners. Risk assessments of a working area must be undertaken prior to the commencement of any work and must be regularly reviewed. Les oprateurs et les ingnieurs travaillant sur l'quipement Kelvin Hughes doivent se conformer aux consignes relatives la sant et la scurit nonces dans le prsent manuel, conformment aux exigences de leurs employeurs respectifs ou comme nonc dans la rglementation du site, ou par les propritaires du chantier naval ou du navire. Des valuations des risques dune zone de travail doivent tre ralises avant le dmarrage de tout travail et doivent tre rgulirement revues. SCV/SxV ENCLOSURE INTERNAL ACCESS SharpEyeTM SCV and SxV systems are factory sealed units that contain no field serviceable, adjustable or repairable parts. WARNING DO NOT DISMANTLE THE RADOME RADAR Installation engineers, system maintainers or operators must not open or disassemble the radome radar. Access to components or sub-assemblies within the system is NOT required for any aspect of installation, commissioning, maintenance, fault finding or operation. Opening the radome radar breaks waterproof seals and voids the warranty status of the unit. ACCS INTERNE LENCEINTE DU SCV/SxV Les systmes SCV et SxV de SharpEyeTM sont des units scelles en usine qui ne comportent aucune pice admettant un entretien, un rglage ou une rparation sur site. AVERTISSEMENT NE DMONTEZ PAS LE RADME DU RADAR Les ingnieurs installateurs, les responsables de lentretien ou les oprateurs du systme ne doivent pas ouvrir ni dmonter le radme du radar. L'accs aux composants ou aux sous-ensembles prsents dans le systme nest PAS ncessaire pour linstallation, la mise en service, lentretien, la recherche de dfaillances ou lexploitation. Louverture du radme du radar entrane la rupture de joints tanches et lannulation de la garantie de lunit. HAZARDS The system operates from an external DC supply and must be fully isolated from all sources of power prior to carrying out any The SharpEyeTM SCV and SxV radomes are not designed to be open or dismantled. WARNING ELECTRICAL HAZARDS The equipment has no safety interlocks. DC VOLTAGES installation or planned maintenance work. The equipment contains materials which may produce toxic fumes if burnt. WARNING The factory sealed SharpEyeTM processor within SCV and SxV systems must not be dismantled as components within the processor contain Beryllium which can represent a risk if the processor is dismantled. At ambient temperatures exceeding +50C, the SCV/ SxV baseplate temperature can exceed +70C. CAUTION BASEPLATE TEMPERATURE WARNING CAUTION KH-1650-CA issue 1 Page 5 of 60 SharpEye SCV & SxV X-Band Radome Radar Chapter 2: Health and safety (Recommandations sanitaires et de scurit) RISQUES Les radmes SCV et SxV de SharpEyeTM ne sont pas conus pour tre ouverts ou dmonts. Aucun verrouillage de scurit nest prvu sur lquipement. AVERTISSEMENT RISQUES LECTRIQUES TENSIONS CC Le systme fonctionne partir d'une alimentation CC externe et doit tre totalement isol de toutes sources dnergie avant de raliser un travail dinstallation ou dentretien planifi. L'quipement contient des matriaux qui peuvent produire des fumes toxiques en cas dincendie. AVERTISSEMENT Le processeur scell en usine de SharpEyeTM prsent dans les systmes SCV et SxV ne doit pas tre dmont car les composants de ce processeur contiennent du bryllium qui peut tre dangereux si le processeur est dmont. AVERTISSEMENT des tempratures ambiantes dpassant + 50 C, la temprature de plaque de base de SCV/SxV peut dpasser +
MISE EN GARDE TEMPRATURE DE PLAQUE DE BASE MISE EN GARDE WORKING ALOFT 70 C. WARNING SAFETY ALOFT When working aloft or near any radar scanners, moving or RF radiating equipment, ALL power sources to the platform and equipment must be fully electrically and mechanically isolated. Prior to working aloft, all supply breakers supplying power to the system must be fully isolated and locked into the OFF position. Ensure someone in authority or at ground level knows of your intentions and ensure that suitable clear warnings are in place. Ensure all means of access aloft are secure and beware of wet or slippery ladder rungs and working areas. All working at height health and safety requirements and procedures, including the inspection and use of personal protective equipment (PPE) such as approved safety harnesses and gloves, must be adhered to at all times as required by your employer, site regulations, shipyard and / or vessel. When working aloft, a safety cordon must be established and managed below the working area(s). WARNING SAFETY CORDON When working aloft, all tools and loose items must be safely stowed or secured so that they cannot present a drop hazard. When weather conditions are poor, a full risk assessment must be carried prior to working aloft as defined by an individuals Poor weather conditions can include but are not restricted to high winds, heavy rain, snow, ice or if access is required at sea, WARNING DROP HAZARDS WARNING ADVERSE WEATHER CONDITIONS employer or shipborne safety procedures. risk of vessel pitch and roll. TRAVAIL DANS LA MTURE AVERTISSEMENT mcaniquement. Lors de travaux dans la mture ou proximit dantennes radar, dun quipement mobile ou mettant des RF, TOUTES SCURIT DANS LA MTURE les sources dalimentation vers la plateforme et lquipement doivent tre totalement isoles lectriquement et Avant tout travail dans la mture, tous les disjoncteurs dalimentation fournissant de lnergie au systme doivent tre totalement isols et verrouills en position OFF (position teinte). Assurez-vous quune personne en charge ou sur le terrain connaisse vos intentions et assurez-vous que des avertissements adapts et clairs sont mis en place. Assurez-vous que tous les moyens daccs la mture sont scuriss et faites attention aux barreaux dchelle et aux zones de travail mouills ou glissants. Toutes les exigences et procdures sanitaires et de scurit pour les travaux en hauteur, notamment celles relatives la vrification et lutilisation d'quipements de protection individuelle tels que des harnais de scurit et des gants homologus, doivent tre respectes tout moment comme exig par votre employeur, la rglementation du site, du Lors dun travail dans la mture, un cordon de scurit doit tre tabli et gr en-dessous de la ou des zones de travail. chantier naval et/ou du navire. AVERTISSEMENT CORDON DE SCURIT KH-1650-CA issue 1 Page 6 of 60 SharpEye SCV & SxV X-Band Radome Radar Chapter 2: Health and safety (Recommandations sanitaires et de scurit) Lors dun travail dans la mture, tous les outils et les lments lches doivent tre correctement rangs ou fixs afin AVERTISSEMENT RISQUES DE CHUTE quils ne constituent pas un risque de chute. AVERTISSEMENT MAUVAISES CONDITIONS MTOROLOGIQUES Lorsque les conditions mtorologiques sont mauvaises, une valuation des risques complte doit tre ralise avant un travail dans la mture, tel que dfini par les procdures de scurit de lemployeur d'un individu ou du navire. Les mauvaises conditions mtorologiques comprennent, mais sans sy limiter, des vents violents, de fortes pluies, de la neige, de la glace ou, si laccs est ncessaire en mer, le risque de tangage ou de roulage du navire. RADIATION HAZARDS WARNING RADIATION HAZARD NON-IONISING Avoid exposure to the main beam of a stationary radar antenna. Avoid standing closer than 15 metres from the central front face of a radiating antenna. Users of cardiac pacemakers should be aware of the possibility that radio frequency transmissions can damage some devices or cause irregularities in their operation. Anyone using such devices should understand the risks present before exposure. If a loss of antenna rotation alarm is raised, the DC power to the system should be immediately switched OFF until the cause of WARNING LOSS OF ANTENNA ROTATION ALARM the loss of rotation is resolved. MICROWAVE RADIATION LEVELS The range at which specified RF exposure limits can be exceeded is far greater for a non-rotating antenna. For that reason, RF transmission without antenna rotation is not a permitted operational mode for this equipment: The system includes interlocks to prevent this occurring. The basic restriction level for the operating frequency of this product, as set out in 1999/519/EC (Annex III table 2) and calculated in accordance with EN50385:2002, is 10W/m2 averaged over a six minute period. For normal operation, the EU basic restriction level for public exposure is only exceeded within 15m of the antenna centre. In all SharpEye systems, the fault condition following the loss of Heading Line and Azimuth data (e.g. the antenna has stopped rotating) will be recognised and trigger the transceiver OFF condition within a few seconds. SCV-A1-10 SXV-A1-10 Rotating Non-rotating Range Within Which the Power Density Exceeds:
10W/m2 0.8m 15m 50W/m2 0.4m 2.9m 100W/m2 0.3m 1.4m Source data document reference TN-2118 issue 2. It is the responsibility of the end user to ensure that they are working from the latest officially released version of the systems handbook when planning an installation or carrying out any form of risk or hazard assessment. NOTICE RISQUES DIRRADIATION AVERTISSEMENT RISQUE DIRRADIATION NON-IONISANTE vitez lexposition au faisceau principal dune antenne radar stationnaire. vitez de vous tenir moins de 15 mtres de la face avant centrale dune antenne rayonnant. Les utilisateurs de simulateurs cardiaques doivent tre conscients du fait que les missions par radiofrquence risquent dendommager certains appareils ou causent des irrgularits dans leur fonctionnement. Toute personne utilisant de tels appareils doit comprendre les risques existant avant une exposition. AVERTISSEMENT PERTE DALARME DE ROTATION DE LANTENNE Lors d'une perte dalarme de rotation de lantenne, lalimentation CC vers le systme doit immdiatement tre teinte
(position OFF) jusqu ce que la cause de la perte de rotation soit rsolue. KH-1650-CA issue 1 Page 7 of 60 SharpEye SCV & SxV X-Band Radome Radar Chapter 2: Health and safety (Recommandations sanitaires et de scurit) NIVEAUX DE RAYONNEMENT MICRO-ONDE L'intervalle dans lequel les limites spcifies dexposition aux RF peuvent tre dpasses est bien plus important pour une antenne qui ne tourne pas. Cest pourquoi, lmission de RF sans rotation de l'antenne nest pas un mode oprationnel autoris pour cet quipement. Le systme inclut des verrouillages de scurit pour empcher une telle situation. Ce niveau de restriction de base pour la frquence dopration de ce produit, comme indiqu dans 1999/519/EC
(Annexe III tableau 2) et calcul conformment EN50385:2002, est de 10 W/m2 en moyenne sur une priode de six minutes. Pour une opration normale, le niveau de restriction de base de lUE pour une exposition publique est uniquement dpass dans un rayon de 15 m du centre de lantenne. Dans tous les systmes SharpEye, l'tat dfectueux suivant la perte de donnes de ligne de foi et dazimut (par ex., lantenne a cess de tourner) sera reconnu et dclenchera l'tat dsactiv (position OFF) de lmetteur-rcepteur en quelques secondes. SCV-A1-10 SXV-A1-10 tat rotatif tat non-rotatif Intervalle dans lequel lintensit de l'nergie dpasse :
10 W/m2 0,8 m 15 m 50 W/m2 0,4 m 2,9 m 100 W/m2 0,3 m 1,4 m ATTENTION Il est de la responsabilit de lutilisateur final de sassurer quil ou elle travaille avec les dernires versions publies officielles du manuel des systmes lors de la planification d'une installation ou de la ralisation dune valuation de risques ou de dangers sous quelque forme que ce soit. RoHS STATEMENT Please contact Kelvin Hughes Ltd for details on the SCV/ SxV RoHS (Restriction of Hazardous Substances). DCLARATION RoHS Veuillez contacter Kelvin Hughes Ltd pour plus de dtails sur le RoHS (Restriction of Hazardous Substances, Restriction sur l'usage de certaines substances dangereuses) du SCV/SxV. WEEE STATEMENT Waste Electrical & Electronic Equipment requirements: When a SharpEyeTM SCV or SxV system has reached the end of its serviceable, please contact Kelvin Hughes Ltd for safe disposal instructions or alternatively arrange for the sealed unit to be returned to Kelvin Hughes for safe disposal. SharpEye specific disposal notice: The SharpEye transceiver(s) located within the sealed transceiver enclosure are factory sealed units that contains no field serviceable parts or lifed components. Components within the SharpEye processor
(all variants) contain traces of beryllium. DCLARATION DEEE Exigences lies aux Dchets d'quipements lectriques et lectroniques : Lorsquun systme SCV ou SxV de SharpEyeTM a atteint la fin de sa dure d'utilisation, contactez Kelvin Hughes Ltd. pour recevoir des instructions d'limination sans risque ou prvoyez le renvoi de lunit scelle Kelvin Hughes pour limination sans risque. Recommandations d'limination spcifique pour SharpEye : Le(s) metteur(s)-rcepteur(s) SharpEye situ(s) dans lenceinte scelle de lmetteur-rcepteur sont des units scelles en usine qui ne comportent aucune pice admettant un entretien sur site ni de composants dure de vie limit. Les composants dans le processeur SharpEye (toutes variantes incluses) contiennent des traces de bryllium. KH-1650-CA issue 1 Page 8 of 60 SharpEye SCV & SxV X-Band Radome Radar Chapter 2: Health and safety (Recommandations sanitaires et de scurit) VIRUS PRECAUTION WARNING ANTIVIRUS WARNING Prior to use, all computing equipment including removable media that is used on or in Kelvin Hughes products MUST be fully scanned for viruses using up to date anti-virus software. Any media containing potential virus infections must not be used. Charges relating to systems found to be infected with a virus will be passed onto the company found to be using computing equipment or media that has not been suitably scanned. Kelvin Hughes cannot be held responsible for damage caused to systems by virus infections. Removable media includes but is not restricted to USB memory sticks, USB hard drives, floppy discs, CD/ DVDs and all forms of removable media. PRCAUTIONS CONTRE LES VIRUS AVERTISSEMENT AVERTISSEMENT ANTIVIRUS Avant utilisation, tous les quipements dinformatique, y compris les supports amovibles, qui sont utiliss sur ou dans les produits Kelvin Hughes DOIVENT tre entirement analyss contre les virus en utilisant un logiciel anti-virus jour. Tout support potentiellement infect par un virus ne doit pas tre utilis. La responsabilit lie aux systmes qui se rvleraient infects par un virus incombe lentreprise qui ayant utilis un quipement dinformatique ou un support qui naurait pas t analys correctement. Kelvin Hughes ne saurait tre tenu responsable des ventuels dommages causs au systme par des infections par des virus. Les supports amovibles comprennent, mais sans sy limiter, les cls USB, les disques durs USB, les disquettes, les CD/DVD et toutes autres formes de supports amovibles. FCC Part 15.19 Warning Statement- (Required for all Part 15 devices) THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS: (1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE, AND (2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION. FCC Part 15.21 Warning Statement:
NOTE: THE GRANTEE IS NOT RESPONSIBLE FOR ANY CHANGES OR MODIFICATIONS NOT EXPRESSLY APPROVED BY THE PARTY RESPONSIBLE FOR COMPLIANCE. SUCH MODIFICATIONS COULD VOID THE USERS AUTHORITY TO OPERATE THE EQUIPMENT. FCC Part 15.105(b) Warning Statement- (ONLY required for 15.109-JBP devices) NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help. Dclaration de mise en garde de la partie 15.19 de la FCC
(Requise pour tous les appareils viss par la partie 15) CET APPAREIL EST CONFORME LA PARTIE 15 DES RGLES DE LA FCC. SON FONCTIONNEMENT EST SOUMIS AUX DEUX CONDITIONS SUIVANTES : (1) CET APPAREIL NE DOIT PAS CAUSER DINTERFRENCES NUISIBLES, ET (2) CET APPAREIL DOIT ACCEPTER TOUTE INTERFRENCE REUE, NOTAMMENT CELLES POUVANT ENTRANER UN DYSFONCTIONNEMENT. Dclaration de mise en garde de la partie 15.21 de la FCC NOTE : LE BNFICIAIRE NEST PAS RESPONSABLE EN CAS DE TRANSFORMATIONS OU MODIFICATIONS NON EXPRESSMENT AUTORISES PAR LA PARTIE RESPONSABLE DE LA CONFORMIT. DE TELLES MODIFICATIONS SONT SUSCEPTIBLES DENTRANER LA RVOCATION DE LAUTORISATION DUTILISATION DE LQUIPEMENT. KH-1650-CA issue 1 Page 9 of 60 SharpEye SCV & SxV X-Band Radome Radar Chapter 2: Health and safety (Recommandations sanitaires et de scurit) Dclaration de mise en garde de la partie 15.105(b) de la FCC
(uniquement requise pour les appareils JBP viss par 15.109) NOTE : Cet quipement a t test et dclar conforme aux limites pour les appareils numriques de classe B, selon la partie 15 des rgles de la FCC. Ces limitations sont conues pour fournir une protection raisonnable contre les interfrences nuisibles dans un environnement domestique. Cet quipement gnre, utilise et peut irradier de l'nergie radiofrquence et, dans le cas dune installation et d'une utilisation non conformes aux instructions, il peut provoquer des interfrences nuisibles aux communications radio. Cependant, il nexiste aucune garantie quaucune interfrence ne se produira dans une installation particulire. Si cet quipement provoque des interfrences nuisibles la rception radiophonique ou tlvisuelle, ce qui peut tre dtect en mettant l'appareil sous et hors tension, lutilisateur peut essayer d'liminer les interfrences en suivant au moins une des procdures suivantes :
Rorienter ou repositionner l'antenne de rception. Augmenter la distance entre l'quipement et le rcepteur. Brancher l'quipement sur une prise appartenant un circuit diffrent de celui sur lequel est branch le rcepteur. Consulter un distributeur ou un technicien radio/tlvision qualifi pour obtenir de laide. KH-1650-CA issue 1 Page 10 of 60 Introduction 3 3.1 System overview SharpEye SCV & SxV X-Band Radome Radar Chapter 3: Introduction SCV-A1-10 Small craft variant The SharpEye SCV is an X-band lightweight coherent radome radar utilising core SharpEye technology. The SharpEye transceiver has been designed for watercraft ranging from RHIBs up to 35m and fast watercraft operated by coastguards, search and rescue, customs, police, Special Forces, armies or navies. SxV-A1-10 Land surveillance The SharpEye SxV is an X-band system that is mechanically and electronically identical to the SharpEye SCV series however the clutter performances have been enhanced for fixed or mobile land based applications. Features: The SharpEye SCV and SxV series offers low cost, low power consumption, lightweight design, ultra-high reliability and superior performance Key features of the SCV/ SxV include:
Simple connectivity with two waterproof connections for DC power and LAN connection Anti-jamming Low power counter surveillance/ covert mode GNSS position and heading output Power: The system operates from a +24 to +30VDC power source. Radome radar:
Detection:
Mounting:
Environmental:
The SharpEye SCV and SxV radome radars are sealed units that contain the following key components:
A 530mm horizontally polarised array SharpEyeTM transceiver processor A Gigabit Ethernet LAN interface (see section 10.2 for details on Internal DC/DC power supply compatible Network Switches) Doppler processing enables the detection of extremely small and slow targets in inclement weather conditions day or night. The SCV and SxV has been designed for easy installation on radar arches, masts, static masts and tripods and has a flexible interface making the system display independent. The systems have been designed to withstand the vibration and shock levels found on RHIBs, small craft, vehicles etc. and be dustproof and waterproof to IP67. System integration: Additional details on system integration are available upon request. Please contact Kelvin Hughes Ltd for information, contact details can be found at the end of this publication. KH-1650-CA issue 1 Page 11 of 60 SharpEye SCV & SxV X-Band Radome Radar Chapter 3: Introduction 3.2 Display interfacing The SCV/ SxV X-Band radome radars are designed to be interfaced via a LAN connection to a suitable command and display sub-system. COMMISSIONING NOTICE This handbook details the installation, termination and maintenance of the SCV/ SxV only and does not cover the commissioning or operation of third party equipment or display sub-systems. 3.3 Typical systems Kelvin Hughes Ltd NAVIGATION DISPLAY KH-1650-CA issue 1 Page 12 of 60 SharpEye SCV & SxV X-Band Radome Radar Chapter 3: Introduction SMALL CRAFT DISPLAY Example of an SCV integrated with a small craft display A second display for an additional command position is shown with dotted lines KH-1650-CA issue 1 Page 13 of 60 SharpEye SCV & SxV X-Band Radome Radar Chapter 3: Introduction Page intentionally blank KH-1650-CA issue 1 Page 14 of 60 SharpEye SCV & SxV X-Band Radome Radar Chapter 4: Positioning of radar equipment Positioning of radar equipment 4 To achieve the full potential of a radar system there must be no obstructions in the path of the beam from the antenna. In practice however obstructions occur some of which are unavoidable. In the case of the SCV these obstructions include interactions with the masts, sponsons, the vessel superstructure and the sea conditions. In SxV applications these obstructions can include buildings and land masses. The proximity of the radar to infrastructure such as masts, aerials etc. is an important consideration as, due to the high level of sensitivity of modern radar receivers, the reflected signals can manifest as false echoes on the radar display. Where available, the appropriate use of blanking sectors to prevent radar transmission towards an obstruction limits the appearance of false echoes. Where infrastructure is located in the field of view of the antenna this is not always possible. The SCV/ SxV should be mounted as high as is practical given the constraints of the installation being considered. BLOCKAGE AND REFLECTION Interaction of the radar antenna beam with an obstruction impacts the performance of the radome radar and may be considered under two headings which are detailed below:
Blockage: Where part of an obstruction is directly in the path of the beam from the antenna. Reflection: Where energy from the antenna reflects from part of a structure. Clearly, when part of a structure is directly in the path of the beam from the antenna then reflection will also occur. Note: The effects discussed in the following are not only related to metallic structures. All objects, whether they are metal, plastic, wood, etc. can cause blockage and reflection resulting in the effects discussed. BLOCKAGE: The drawing to the right shows a mast and antenna in plan view giving an example of blockage by a mast. Notice how the blockage can impact on the energy from the antenna over a large scan angle depending on how close the obstacle is to the antenna and its size. As an example, an obstacle that is 3m away from a 0.53m wide SCV/ SxV antenna will be in the path of the beam over an angle of at least 10, depending on the width of the obstacle. The effect of this form of blockage is to reduce the power returned from a target and to increase the clutter received by the radar so that the ability to detect the target is degraded (and a blind spot may even occur). This degradation in performance of the radar occurs while the obstacle remains in the antenna beam although it reduces as the blockage moves towards the edge of the beam. The magnitude of the blockage effect is dependent on the size and physical characteristics of the obstacle. As the size of the object increases, so does the degradation in radar performance. Antenna Beam Blockage by a Mast KH-1650-CA issue 1 Page 15 of 60 SharpEye SCV & SxV X-Band Radome Radar Chapter 4: Positioning of radar equipment Clearly, when the obstacle is as large or larger than the antenna the radar becomes completely blind although, as already indicated, blind spots may still occur when the obstacle is smaller than the antenna. Whilst the most obvious features on a vessel (SCV) leading to blockage are masts, funnels, railings, etc. Decks and cabin roofs can also cause blockage if the antenna is not mounted sufficiently high. The same effect can occur when mounting the SxV on a building or mast. REFLECTION: The drawing to the right shows a mast and antenna in plan view, the mechanism of reflection is from an obstacle such as the mast. Energy from the antenna is reflected in a different direction to that in which the antenna is pointing. If this is incident on a target, then reflections from the target will return via the same path. If the reflections have sufficient magnitude they will produce a return on the display in a direction corresponding to the pointing angle of the antenna, thus producing a ghost target. Antenna beam reflection by a mast The angular position of such ghost targets will be dependent on the shape of the obstacle and some obstacles will produce ghost targets which are close to the real target, thus resulting in target smearing. Masts and funnels will generally tend to produce distinct ghost targets and railings are likely to lead to target smearing. On some installations such as modern high speed vessels where a large portion of the deck or mounting surface may be within the antennas vertical beamwidth, the radar signal is likely to be reflected. Horizontal surfaces will tend to reflect the radar signal upwards away from other reflectors causing no problem. Inclined or curved surfaces can reflect energy from the antenna into the horizontal plane at a different angle to the pointing angle of the antenna. This can lead to ghost returns and/ or target smearing. Similar effects can occur on static or vehicle installations. SEA & LAND CLUTTER Sea and land clutter returns are not only dependent on the sea state but also on the height of the radar antenna. As the antenna height increases so does the sea clutter returns and the range out to which the sea clutter extends. HORIZON RANGE The curvature of the earth limits the range that can be seen by a radar system. Antenna height above sea level Horizon range Horizon range
(NM)
(km)
(metres) 5.0m 10m 15m 20m 5.0NM approx. 7.0 NM approx. 8.5 NM approx. 10 NM approx. 9.3km approx. 13km approx. 15.7km approx. 18.5km approx. The table opposite demonstrates the approximate range to horizon on a generic radar system. KH-1650-CA issue 1 Page 16 of 60 SharpEye SCV & SxV X-Band Radome Radar Chapter 4: Positioning of radar equipment MULTIPATH INTERFERENCE Radar energy reflects from the target directly or following reflection at the surface of the sea. The result is that sometimes the two signals will reinforce each other while at other times they will cancel and create a null. In marine applications (SCV) Multipath is most pronounced when the sea is calm, acting like a mirror, and when the target is simple (essentially comprising a single reflector) such as a buoy. Here multipath reflection may produce a large number of signal nulls at short range. These become less frequent as range increases. In the higher sea states when the sea is rough and is less like a mirror or when the target is complex
(comprising a number of reflectors), as are many vessels, the effect of multipath is less pronounced so that the nulls are less deep. Land based installations can also suffer from multipath. The reflection characteristics can change based on terrain, dampness etc. As the height of the radar antenna (or target) increases, then the frequency of the nulls also increases. It is clear that there is no definitive solution to the installation of a radar antenna on a vessel or a permanent land based site. Each installation should be examined on its own merit with each aspect of performance assessed appropriately. To this end, we advise that you seek guidance from Kelvin Hughes for antenna installations by submitting a drawing illustrating the position of the antenna in relation to the vessels structure (SCV) or mounting structure (SxV) and nearby obstacles. ANTENNA LOCATION AND SEPARATION SharpEyeTM SCV and SxV radomes contain a SharpEyeTM radar transceiver and a GNSS antenna. The system must be mounted with a clear view of the horizon. Wherever possible, ensure the antenna is placed outside the beam path of any other transmitting equipment for example:
Radar:
Satcom:
INMARSAT A, B, C, or M; typically 10 from the arrays centre point in any of the possible transmitting directions. Typically 15 from the arrays centre point. VHF/ SSB:
Do not place within 3 metres of a VHF or SSB radios or their antennas. KH-1650-CA issue 1 Page 17 of 60 Image ofTargetTarget SharpEye SCV & SxV X-Band Radome Radar Chapter 4: Positioning of radar equipment Page intentionally blank KH-1650-CA issue 1 Page 18 of 60 SharpEye SCV & SxV X-Band Radome Radar Chapter 5: Preparation for installation 5 5.1 Pre-Installation requirements Preparation for installation SCV and SxV systems have been designed as plug and play units that should be installed by competent engineers familiar with the installation and commissioning of radar equipment. Installation engineers should familiarise themselves with all sections of this handbook prior to carrying out any installation, commissioning or maintenance tasks on SCV/ SxV products. Incorrect or poor installation of the equipment can invalidate the warranty of the system. The SCV/ SxV must be mounted and terminated as instructed in this handbook. UNIT INSPECTION The SCV/ SxV has been designed with protective coatings and finishes to allow it to withstand demanding environments around the world. However if the unit sustains mechanical damage, such as scores or scratches that is sufficient enough to damage the coatings and expose underlying metal, the unit's ability to withstand salt corrosion may be reduced. Damage to finishes or metalwork should be made good immediately. The unit should be protected from potential damage by other equipment, for example accessing or installing other equipment in the vicinity of the SCV. Care should be taken when mating and de-mating connectors so that the shell finish of the connectors is not damaged. Prior to installation, the unit should be checked to ensure that no damage has occurred during transport. Any damage that has occurred, including accidental dropping of the unit, must be reported to Kelvin Hughes Ltd before the unit is installed. Damage must only be repaired when authorised by Kelvin Hughes Ltd. TOOLS In addition to the normal tools required for installation and service work, the following will be required to install the SCV or SxV radomes:
M4 / 7mm spanner (SCV brackets) M6 / 10mm spanner (earth connections) M8/ 13mm spanner (main mounting bolts). Torque wrench (tightening the main chassis bolts to 22Nm). Note Multimeter / safety ohmmeter or bridge megger (earth bonding tests) NON-REMOVABLE RADOME COVER The 8 bolts that retain the radome cover to the chassis and MUST NEVER BE REMOVED. Access to components or sub-assemblies within SCV or SxV systems is NOT required for any aspect of installation, commissioning, maintenance or operation. Removal of the radome cover invalidates the warranty status of the system and breaks waterproofing seals. CAUTION GENERAL PRECAUTIONARY NOTICES The radome must not be painted. Labels and/ or stickers must not be placed on the radome. DRT TORQUE VALUES Torque settings noted in this handbook are dry torqueing values. Appropriate wet torque values should be used as appropriate. Please contact Kelvin Hughes if additional information is required. KH-1650-CA issue 1 Page 19 of 60 SharpEye SCV & SxV X-Band Radome Radar Chapter 5: Preparation for installation 5.2 Fitting kits KIT CONTENTS Typically the SCV/ SxV system is supplied with an installation kit that includes:
FIXINGS All the necessary fixings required to mount the SCV/ SxV. Fixings supplied are 316 (A4) grade stainless steel, passivated, zinc plated for marine applications ANTI-VIBRATION MOUNT An anti-vibration mount is provided as standard with SCV systems and can be ordered separately for SxV systems (detailed in the fitting kits below). Before commencing the installation, check the kit contents of this against the packing list contained within the kit, ensuring all necessary parts are present. Any missing or damaged parts should be immediately reported to Kelvin Hughes Ltd. SCV SCV-A172 SCV-A170 SCV-A160-1 fitting kit Anti-vibration mount Cable bracket assembly SCV-A145 Earth strap 55-100-0566-001 Fasteners Nuts, bolts & washers Anti-Corrosion Paste / grease M4 M8 x 25mm M8 x 45mm SxV SXV-A100 fitting kit The anti-vibration mount is supplied as standard and MUST BE INSTALLED on all SCV applications. Please refer to section 6.1 for assembly details. This assembly is assembled onto the anti-vibration plate. Please refer to section 6.2 for assembly details. Earth strap that must be used to connect the radar to a tested /
proven earth/ ground. Please refer to section 7.4 for assembly details. 10ml Syringe of anti-corrosion paste/ grease. Please refer to section 6.3 for application details. Used to assemble the SCV-A170 / SCV-A172 to the SCV. Used to fix the SCV to its mounting position See notes in section 6.3 regarding maximum thread depths. SCV-A145 Earth strap Anti-Corrosion Paste / grease 55-100-0566-001 Fasteners Nuts, bolts & washers M8 x 25mm SCV-A135
(OPTIONAL) Anti-vibration mount Earth strap that must be used to connect the radar to a tested /
proven earth/ ground. Please refer to section 7.4 for assembly details. 10ml Syringe of anti-corrosion paste/ grease. Please refer to section 6.3 for application details. Used to fix the SCV to its mounting position See notes in section 6.3 regarding maximum thread depths. An anti-vibration mount is not supplied as part of an SxV installation kit but can be requested as a chargeable option for use in situations where vibration is anticipated. CABLES Typical installation kits do not contain cabling for the SCV and SxV which must be ordered separately. SCV/ SxV SCV-A167-**
Note 1 SCV-A168-**
Note 2 Standard cables part numbers Power Input cables. Standard length is 10m. 15, 20, 25 & 30m lengths are available on request. Refer to section 7.2. Connects DC power to the radar assembly. Ethernet Cable. Standard length is 10m. 15, 20, 25 & 30m lengths are available on request Connects the radar assembly to the control system and provides communications (Control and Video) to and from the unit. The cable supports Gigabit Ethernet. Note 1: Where -** is the cable length in metres, e.g. a standard 10m Power cable would be SCV-A167-10. Note 2: SCV variant SCV-A1-10-ADAC should be ordered with power cable SCV-A177-** rather than SCV-A167-**. Please contact Kelvin Hughes Ltd if alternative cable assemblies are required. KH-1650-CA issue 1 Page 20 of 60 SharpEye SCV & SxV X-Band Radome Radar Chapter 5: Preparation for installation 5.3 Location POSITION The installation of the equipment needs to be assessed against local operating procedures; please refer to section 4 for additional information on the positioning of radar equipment. RADHAZ PRECAUTIONS If video ceases to be displayed and the SCV/ SxV is installed in a position where a person can be within 15m of the antenna, the operator should cease transmission immediately and investigate the problem, ensuring that the SCV is not at fault. Please refer to the Radiation Hazard warning notices that can be found in section 2: Health & Safety notices and in the operator notices in section 10:
Operator instructions. DO NOT STEP The SCV / SxV should never be placed in a position where it can be used as a step or aid to climbing. Do not stand on the SCV / SxV radar. 5.4 Lifting considerations LIFTING EQUIPMENT All health & safety requirements as laid down by the vessel, shipyard or site safety regulations must be checked and observed at all times when lifting any equipment. Any applicable local or national regulations must also be observed In line with Kelvin Hughes, shipyard, vessel and/ or site requirements, all appropriate Personal Protective Equipment (PPE) such as safety harnesses, fall arresters, hard hats, safety boots, safety glasses and gloves must be inspected prior to use and worn at all times when lifting equipment and when working aloft. Never leave equipment unsupported on a mounting platform. Ensure that tools or equipment cannot present any form of drop hazard. Where special equipment such as cranes hoists and jigs is required, consideration must be given to the authority to use such equipment. During lifting, a safety zone shall be established beneath the lifting area, around any cranes or platforms. Safety personnel must ensure that persons do not encroach into the area of work. When making arrangements for lifting any equipment, consult with the lifting operator to obtain the best and safest method of securing the lifting strops or ropes to the equipment. Lifting operators should be advised of the areas of a system that are susceptible to damage such as the SCV or SxV radome cover. Check that the centre of gravity of the equipment cannot cause the lifting strops or ropes to slip or move. MANUAL LIFTING The SCV/ SxV radome radar weights approximately 22Kg (SCV with anti-vibration mount & cable bracket fitted) or 20kg (SxV) so may be manually lifted by two-people. In addition to the precautions noted above, all manual lifting requirements and precautions must be observed when lifting the equipment. KH-1650-CA issue 1 Page 21 of 60 SharpEye SCV & SxV X-Band Radome Radar Chapter 5: Preparation for installation Page intentionally blank KH-1650-CA issue 1 Page 22 of 60 SharpEye SCV & SxV X-Band Radome Radar Chapter 6: Mechanical installation 6 Mechanical installation 6.1 Mounting platform MOUNTING PLATE The SCV/ SxV radome radar requires an 8.0mm flat aluminium or steel mounting plate. The plate should be pre-drilled to accommodate the radome radar, an earthing/ grounding point, any cables access holes and cable restraining points. Prior to installation, the proposed mounting plate and location must be inspected and accepted as being suitable. Example of SCV and SxV mounting plate. Not to scale. See following pages for dimensions All four planes shown (A, B, C and D) should be checked to ensure the surface is flat and that there is no curvature of the plate. The maximum deviation should not exceed 1.0mm. The mounting platform and any supports (masts etc.) must be able to fully support the weight of the radome radar and be designed to minimise vibration. MOUNTING BARS The full mounting surface area of the SCV/ SxV chassis must be in contact with the mounting plate. Kelvin Hughes STRONGLY advises against mounting the SCV/SxV on brackets or mounting bars as this can cause twisting of the radome radar chassis. A flat, even surface is strongly recommended. EARTHING/ GROUND POINT A tested/ proven ground point grounding/ earthing point will be required on the mounting plate or platform for connection to the M6 earth stud located on the base of the radome radar. See section 6.4
(SCV) or section 6.5 (SxV) for the location of the earth stud. Kelvin Hughes Ltd recommend that the earth/ ground connection is always connected to the common platform chassis ground. BATTERY CONNECTION Portable systems powered by a battery do not require an earth connection ORIENTATION The SCV/ SxV radome radar must be mounted in an upright position as shown below with the Mounting brackets, bars or tubes are NOT recommended. LAN and DC connectors pointing backwards/ aft. Due to the beamwidth of the antenna, target detection will be significantly reduced if the SCV/
SxV assembly is tilted by more than 12.5 from horizontal/ flat. Please consult with Kelvin Hughes Ltd if alternative mounting positions (i.e. inverted etc.) are required. Power & LAN connections Up Forward KH-1650-CA issue 1 Page 23 of 60 SharpEye SCV & SxV X-Band Radome Radar Chapter 6: Mechanical installation 6.2 Anti-vibration mount/ Cable bracket assembly SCV APPLICATIONS (MOUNT SUPPLIED) SCV-A170 Anti-Vibration Mount The Anti-Vibration mount and cable bracket assembly are supplied pre-assembled as part of the SCV-A160-1 fitting kit ready for fitting to an SCV. These assemblies must be fitted to the SCV prior to placing the unit on its final mounting position. SXV APPLICATIONS (OPTIONAL) SCV-A135 Anti-vibration mount An anti-vibration mount is not supplied as part of an SxV installation kit but can be requested as an option for use in situations where vibration is anticipated. Where required, the mount must be fitted to the SxV prior to placing the unit on its final mounting position. FASTENERS The Fasteners supplied in the installation kit must be used as follows:
M4 nuts and washers M8 x 25mm bolts and washers Fixes the combined SCV-A170 and SCV-A172 to the base of the Used to Assemble the SCV SCV-A170 to the SCV-A172. SCV. Used to fix the SCV to its mounting position. Note See notes in section 6.3 regarding maximum thread depths. M8 x 45mm and washers INSTALLATION PRECAUTIONS The SCV will need to be inverted to fit the Anti-vibration plate and the cable support bracket. The unit should be placed on a surface that will protect the radome from being scratched or damaged. Do not apply un-necessary force to the base of the unit as this could deform the radome cover. During installation, the 20mm maximum thread depth of the main SCV/SxV mounts or the anti-
vibration mounts should never be exceeded (see section 6.3 for additional details). Note: The 8 x 45mm bolts are for SCV applications where the combined SCV-A170 and SCV-A172 plates have been fitted. For application where no anti-vibration/ cable bracket plates are fitted please use the M8 x 25mm bolts from the fitting kit. KH-1650-CA issue 1 Page 24 of 60 SharpEye SCV & SxV X-Band Radome Radar Chapter 6: Mechanical installation SCV-A170 CABLE BRACKET ASSEMBLY SCV-A172 ANTI-VIBRATION MOUNT KIT KH-1650-CA issue 1 Page 25 of 60 SharpEye SCV & SxV X-Band Radome Radar Chapter 6: Mechanical installation INSTALLATION PROCEDURE A. Invert the SCV assembly ensuring the unit is placed on a surface that will not damage or scratch the top of the radome casing. B. SCV-A170 cable bracket assembly rests in-between the two connectors as shown below. C. The SCV-A172 anti-vibration plate is fitted with four anti-vibration mounts. One of these mounts has longer fasteners that protrude below the plate. These longer fasteners align with the slots in the SCV-A170 cable bracket assembly and are secured using the M4 fasteners, plain and spring washers found in the fitting kit. TIP: Fit the anti-vibration plate to the cable bracket assembly and loosely tighten the 4 longer fasteners. Align the cable bracket assembly then align the anti-vibration plate with the 4 main fastening holes on the base of the transceiver. The assembly can then be removed and the longer shock mount screws can be fully tightened. D. The assembly can be fastened to the SCV using the M8 x 25mm bolts, plain and spring washers provided in the fitting kit. E. Tighten the main bolts to a torque of 22Nm (see precautions in section 6.3). EXAMPLE OF MOUNTING SCV-A170 cable bracket assembly placed onto an SCV. SCV-A172 anti-vibration plate showing the four longer mounting fasteners (circled) that align with the A170 cable bracket assembly. Completed assembly shown prior to the four mounting bolts being fitted. Example of bolt and washer arrangement KH-1650-CA issue 1 Page 26 of 60 SharpEye SCV & SxV X-Band Radome Radar Chapter 6: Mechanical installation 6.3 Installation MOUNTING BOLTS The radome radar is secured to the mounting plate using four M8 stainless steel bolts and washers supplied in the fitting kit (see previous page for washer arrangements). The mounting bolts supplied in the fitting kit MUST be used to fix the SCV/SxV to the mounting platform as detailed in the following table:
M8 MOUNTING BOLTS MAXIMUM THREAD DEPTH 20MM SCV shown with anti-vibration mount fitted SxV shown without anti-vibration mount SCV INSTALLATIONS or Installations where the SCV-A170 Cable bracket assembly and SCV-A172 anti-vibration mount are fitted. M8 x 45mm bolt and washers Example of bolt and washer M8 x 25mm bolt and washers SxV INSTALLATION or Installations WITHOUT the SCV-A170 Cable bracket assembly and SCV-A172 anti-vibration mount Please contact Kelvin Hughes Ltd if alternative fasteners are to be used. MAXIMUM THREAD DEPTH The depth of the thread for the M8 fasteners in the radome radar is 20mm maximum tightened to a torque load of 22Nm (see illustration above). In general, unless otherwise stated, the absolute minimum engagement depth for fixings is 1.5 x diameter. IMMERSIBLE BREATHER HEAD arrangement The breather head protects the system against air pressure build up within the radome whilst preventing water ingress. The maintenance free breather is a factory fitted component and MUST NOT be painted, pierced, covered or removed. ANTI-CORROSION PASTE/ GREASE Lightly grease the threads of the mounting bolts prior to fitting using the tube of grease provided in the fitting kit. If this is not available, the preferred material for the grease is Molybdenum Disulphide
(Kelvin Hughes part number 55-100-0562-
001). KH-1650-CA issue 1 Page 27 of 60 SharpEye SCV & SxV X-Band Radome Radar Chapter 6: Mechanical installation 6.4 DIMENSIONS: SCV SCV WEIGHT NOTE SCV-A1-10-****: 20Kg SCV-A170 cable bracket: 421g SCV-A172 Anti-Vibration mount: 2Kg KH-1650-CA issue 1 Page 28 of 60 SharpEye SCV & SxV X-Band Radome Radar Chapter 6: Mechanical installation 6.5 DIMENSIONS: SxV KH-1650-CA issue 1 Page 29 of 60 SharpEye SCV & SxV X-Band Radome Radar Chapter 6: Mechanical installation Page intentionally blank KH-1650-CA issue 1 Page 30 of 60 SharpEye SCV & SxV X-Band Radome Radar Chapter 7: Termination 7 7.1 Cabling and termination Termination CABLING Cabling, terminations and connections are to be made as per the latest version of IEE wiring regulations BS-7671, Requirements for Electrical Installation. Cables are to be of correct specification and rating and should be run in suitable cable trays or guides. They should be laid in positions that cannot cause an obstruction or hazard. Cable runs must allow for service loops. All cables should be secured in position using cable ties placed at regular intervals. In order to reduce electromagnetic interference effects, all cables should be routed as directly as possible, consistent with consideration for other equipment. Cables should not be installed close to high-power lines such as radio-transmitter lines. Crossing of cables should be done at right angles (90) to minimize magnetic field coupling. Cables must be laid and secured in a fashion that does not place undue stress or strain on the cable or the connector. Ensure excessive strain is not applied to the cable or the connecters when connecting and disconnecting the DC power and LAN cables. Provision must be made on the mounting platform for securing of the cables. MINIMUM BEND RADIUS The minimum bend radius of the cable must be observed when laying the cable. Where a bend radius is not stated, a minimum bend radius of 12 x the cable diameter should be assumed for Kelvin Hughes Ltd supplied cable. CORRECT INCORRECT A cable correctly laid taking the Cables incorrectly laid with the bend below the minimum bend radius minimum bend radius into account. Drawings shown are for reference use only and do not represent a scaled drawing of the minimum bend radius. which places strain on the cable and connector. CONNECTION/ CONNECTOR NOTES Fully isolate all sources of power to the system before mating and de-mating any connectors. Connectors should be inspected immediately prior to installation to ensure that pins are not bent, Installation of external connectors should only be undertaken in dry conditions. corroded or otherwise damaged and that no contamination, pollution or moisture has entered either mating half. Where required, cleaning should be undertaken carefully, in such a way as not to damage the contacts or insulation. For example to remove contamination and moisture compressed air spray may be used in accordance with manufacturer's and local guidance along with nylon brushes. The protective caps on the SCV/ SxV connectors are retained and must be left attached to the system for future use. The connecter must never be left disconnected and exposed to the elements. The pre-terminated connectors are keyed to prevent incorrect connection. When fitted ensure each connector is fully inserted and makes a full waterproof seal. Ensure the cable restraining method does not strain the connector as this could cause the connector to become damaged. Ensure excessive strain is not applied to the cable or the connecters when connecting and disconnecting the DC power and LAN cables. KH-1650-CA issue 1 Page 31 of 60 SharpEye SCV & SxV X-Band Radome Radar Chapter 7: Termination BULKHEAD AND DECK PENETRATION Any bulkhead penetrations which are opened must be closed and sealed using appropriate materials thus maintaining existing water or fire proofing precautions. OVERCURRENT PROTECTION DEVICES All supplies to the system must be fitted with a suitably rated, clearly labelled overprotection device such as a breaker or a fuse. CABLE BRACKET ASSEMBLY The SCV-A170 cable bracket assembly used on SCV systems includes two cable clamps that must be used to restrain the cables as demonstrated opposite. CABLE CLAMP BOLTS Lightly grease the threads of the four bolts prior to final assembly using the tube of grease provided in the fitting kit. CONNECTOR ACCESS Depending on the mounting arrangement, access to the two base plate connectors (LAN
& DC input) is restricted when the SCV/ SxV is fully bolted to the mounting plate. In this situation, it is recommended these connections are correctly fitted and secured before the main mounting bolts are fully tightened. AC SUPPLIES Where a mains powered AC to DC Power supply is to be connected to the system (not Kelvin Hughes standard supply), the unit must be designed in accordance with the requirements of IEC 60950-
1:2005. This should include provision of a suitable rated overcurrent protective device and a protective earth connection, made to suitable earth point on the mounting platform. Example of a cable installed in the cable bracket assembly The power supply should be designed in such a way that under single fault conditions mains voltages cannot be applied to its DC output. MATING/ DE-MATING The connectors are a keyed Push-Pull latching connector that can only be inserted in one orientation into the correct mating half. To remove the connectors pull the collar back with minimal force to release the connector, then pull with minimal force. Correct mating and de-mating of the connector requires very little force. If effort is required when connecting or disconnecting connectors, the wrong technique is being employed. KH-1650-CA issue 1 Page 32 of 60 SharpEye SCV & SxV X-Band Radome Radar Chapter 7: Termination 7.2 DC input SCV-A167-** Note 1 & Note 2 A pre-terminated cable can be supplied for connecting the DC input to PL1 located on the base of the SCV/ SxV radome radar. CABLE LENGTH Standard systems typically use 10 metres of cable however other cable lengths are available as detailed below. Part No. Note 2 SCV-A167-05 SCV-A167-10 SCV-A167-15 SCV-A167-20 SCV-A167-25 SCV-A167-30 DC input connection Length (mm) 5000 10000 15000 20000 25000 30000 Any additional cabling required for connecting the system to the DC power, breakers etc. should be of a sufficient gauge to ensure that the minimum voltage required by the SCV/ SxV is maintained under the worst case load conditions (see section 13.3). CABLE TYPE LSZH 3x14AWG Screened. Diameter approx. 11mm. CONNECTOR TYPE Fischer UltiMate UP01L13 F303S BK1 Z1ZB (SCV/SxV Mating half UR02W13 M303S BK1 E1AB) DC POWER SOURCE The SharpEyeTM SCV/ SxV series has been designed to run from a +24VDC to +30VDC supply, with
+28VDC being used in typical installations. For longer cable runs higher DC supply voltages are recommended. Please refer to section 13.3 for details and full electrical specifications. The SCV/ SxV must not be connected directly to an unprotected/ un-switched DC power source. Isolate all of DC power to the system before mating or de-mating the connectors. WARNING Connectors should be inspected prior to connection to ensure there are no foreign object or damage NOTICE to the connector. Note 1: Where -** is the length of the cable in metres. Note 2: SCV variant SCV-A1-10-ADAC should be ordered with power cable SCV-A177-** rather than SCV-A167-**. Please contact Kelvin Hughes Ltd if alternative cable assemblies are required. Note 3: DC circuit breakers and switches are not supplied. KH-1650-CA issue 1 Page 33 of 60 SharpEye SCV & SxV X-Band Radome Radar Chapter 7: Termination DC BREAKER There is no ON/ OFF switch on the SharpEyeTM SCV or SxV radome radar. The DC supply to the radome radar must be connected via a suitable rated user accessible DC breaker. See section 13.3 for the breaker rating. Note 3 EXAMPLE OF DC POWER CABLE CONNECTION DETAILS DC CONNECTOR PIN ORIENTATION Viewed from the back/ soldering side KH-1650-CA issue 1 Page 34 of 60 SharpEye SCV & SxV X-Band Radome Radar Chapter 7: Termination 7.3 LAN input SCV-A168-** Note A pre-terminated cable is available for connecting the LAN cable to the connector located on the base of the SCV/ SxV radome radar. CABLE LENGTH Standard systems typically use 10 metres of cable however other cable lengths are available as detailed below. Part No. SCV-A168-05 SCV-A168-10 SCV-A168-15 SCV-A168-20 SCV-A168-25 SCV-A168-30 CABLE TYPE LSZH Cat 5e S/FTP. Diameter 8mm approx. LAN connection Length (mm) 5000 10000 15000 20000 25000 30000 CONNECTOR TYPE Fischer UltiMate UP01L11 M012S BK1 Z1ZB (SCV/SxV Mating half UR02W11 F012S BK1 E1AB) EXAMPLE OF LAN CABLE CONNECTION DETAILS LAN CONNECTOR PIN ORIENTATIONS SCV connection Viewed from the back/ soldering side Note: Where -** is the length of the cable in metres. RJ45 connection viewed from front KH-1650-CA issue 1 Page 35 of 60 SharpEye SCV & SxV X-Band Radome Radar Chapter 7: Termination 7.4 Ground/ Earth cable SCV-A145 EARTH BONDING CABLE The earth strap supplied in the fitting kit MUST be used to fix the SCV/SxV to a proven earth point on the mounting platform using the fixings supplied with the unit. CABLE LENGTH 250mm long. Other cable lengths are available, Please contact Kelvin Hughes Ltd for further details. CONNECTION The SCV/SxV is grounded via the M6 earth stud located on the base of the SCV/SxV which should be connected to a tested/ proven ground point. For EMC/ interference reasons, Kelvin Hughes Ltd recommend that the earth/ ground connection is always connected to the common platform chassis ground. M6 earthing stud The ground/ earth termination MUST BE MADE using the SCV-A145 cable supplied in the fitting kit Please contact Kelvin Hughes Ltd if alternative grounding arrangements are required. NOTICE BATTERY CONNECTION SxV systems powered by a battery do not require an earth connection. CABLE DETAILS Example of standard SCV-A145 cable CABLE SPECIFICATION Conductor CSA (mm2) Cable Length Stud size ref. Hole Ref.
(diameter) 250 Note 15 M6 6.4 Lug width 15.5 Lug thickness 2.2 Current rating 120A KH-1650-CA issue 1 Page 36 of 60 SharpEye SCV & SxV X-Band Radome Radar Chapter 7: Termination M6 EARTH STUD ASSEMBLY The strap and washers should be assembled as shown below. When the earth strap has been secured, the surfaces should be lightly covered in the anti-corrosion paste supplied as part of the fitting kit. This paste protects the connection against water ingress and corrosion. In addition, Denso tape or a suitable self-amalgamating tapes may be used to protect the connection/
joint from corrosion. CONDUCTIVITY TESTING Once fitted, the earth bonding should be measured to ensure good conductivity is achieved. See Section 11: Planned maintenance for the correct test procedure. KH-1650-CA issue 1 Page 37 of 60 SharpEye SCV & SxV X-Band Radome Radar Chapter 7: Termination 7.5 CONNECTION DIAGRAM CABLE DEATILS Further details on the cables shown in the above diagram can be found in the following sections of this handbook. DC input cable:
LAN Connector and cable:
Earth Strap:
Longer DC power cables:
See section 7.2 See section 7.3 See section 7.4 See section 13.3 KH-1650-CA issue 1 Page 38 of 60 SharpEye SCV & SxV X-Band Radome Radar Chapter 8: Commissioning 8 8.1 Overview Commissioning THE SCV/ SXV IS SHIPPED PRE-CONFIGURED In most applications no commission is required as the system is configured via the display sub-
system. Please contact Kelvin Hughes Ltd where advanced commissioning is required. COMPUTING EQUIPMENT Where commissioning of the transceiver is required, it will be necessary to connect a laptop computer to the SCV/ SxV. Please refer to the anti-virus warnings in the health & safety section located at the beginning of this handbook prior to connecting any computing equipment to the SCV/ SxV. The procedures noted in this handbook do not detail the configuration of firewall or antivirus software on a laptop computer. Kelvin Hughes can only offer technical assistance with the parameters directly related to the configuration of the SCV/ SxV. CAUTION IP ADDRESS The setting to work/ commissioning web page contains the SCV/ SxV IP addresses. Unless specifically instructed the IP addresses MUST NOT be changed. Incorrect configuration of the IP addresses can render the system un-operational. IP ADDRESS RECORD Where an IP address is changed, record the addresses below:
OLD IP address
(for reference use) NEW IP address BEARING ADJUSTMENT/ RANGE ALIGNMENT Bearing adjustment of the video such as heading adjustment, frequency skew correction and azimuth adjustment due to selected range mode is calibrated using the display sub-system. This cannot be adjusted or commissioned at the SCV/ SxV. Please refer to the system commissioning handbook for the display sub-system for instructions. SYSTEM INTEGRATION Additional details on system integration are available upon request. Please contact Kelvin Hughes Ltd for information. Contact details can be found at the end of this publication. COMMISSIONING SETTINGS Commissioning settings are stored in non-volatile memory within the unit. The settings cannot be backed up so a manual record of all settings must be made in the relevant section of the handbook. KH-1650-CA issue 1 Page 39 of 60 SharpEye SCV & SxV X-Band Radome Radar Chapter 8: Commissioning 8.2 Commission web page In most applications it will not be necessary to access this page. Parameters within the web page must only be adjusted when specifically advised by Kelvin Hughes Ltd or as part of a system integration instruction document. When access to the commission pages is required, connect a laptop computer to the LAN connection of the SCV/ SxV system. The connection can be made using the LAN cable supplied with the equipment (see Computing Equipment in the previous page). The SCV/ SxV commissioning web page can be accessed by opening a web browser and entering the following IP address: http://192.168.22.70:8008 SCV Configuration Example of SCV/ SxV commissioning web page. KH-1650-CA issue 1 Page 40 of 60 SharpEye SCV & SxV X-Band Radome Radar Chapter 8: Commissioning 8.3 Compass Settings INTERNAL COMPASS. The SCV/ SxV is supplied with an internal compass that can be enabled as part of the system integration. When enabled, NMEA messages are output within the UDP packets. Where the internal compass is enabled and in use, the compass must be calibrated to eliminate any errors caused by magnetic materials within the installation. The following tests will require the platform to be manoeuvred into different positions / directions NOTICE to calibrate the internal compass. Set up Open Web page Record current values Start Compass Calibration Compass Declination With the DC supply to the system switched OFF, connect the SCV to a virus free laptop computer. The connection can be made using the LAN cable supplied with the equipment. Switch ON the DC supply to the system. During the configuration of the system, It is necessary for the GPS to have an unimpeded view of the sky and be free from electromagnetic interference at GPS frequencies. On the laptop PC, open an internet browser and enter the following address:
192.168.22.70:8008 Compass:
GPS:
Record the Compass and GPS Module Status shown on the web page. Click on the Start Compass Calibration button and follow instructions on the web interface. It will be necessary for the platform to be rotated or manoeuvre in a complete circle, through North, South East and West. The radius of the circle is unimportant. If known, set the Compass Declination. Notes: Magnetic declination or variation is the angle on the horizontal plane between magnetic north and true north. This angle varies depending on position on the Earth's surface, and changes over time. If the position of the vessel changes substantially from the location it was last calibrated in, this process should be repeated. Where the SCV/SxV is connected to a display system and is using a suitably accurate GNSS, Log and Gyro providing regular messages at a suitable rate, it may be preferable to us the check Using external motion data source where the SCV/ SxV uses the external data rather than the internal compass. This should be assessed by the service agent performing the procedure, please contact Kelvin Hughes Ltd for further details. Record the Compass Declination value:
KH-1650-CA issue 1 Page 41 of 60 SharpEye SCV & SxV X-Band Radome Radar Chapter 8: Commissioning 8.4 Blind sector, heading line offset record To determine the blind arcs where the vessel superstructure may block the transmitted RF radiation, identify a strong target on the display and then manoeuvre the vessel or platform in a clockwise circle. Note the start bearing where the target is no longer visible and the stop bearing where the target becomes visible again. There may be multiple blind arcs. Use Head-up mode on the display. Any heading line offsets or blind (mute) sectors that are configured for the system must be recorded on the following diagram. Description:
Description:
KH-1650-CA issue 1 Page 42 of 60 SharpEye SCV & SxV X-Band Radome Radar Chapter 9: Completion of installation Completion of installation Installation checks 9 9.1 On completion of an installation the following tasks must be carried out. TASK Confirmed Fastenings Anti-vibration mounts Ensure that all fastenings are correctly and securely tightened to the correct torque setting (where specified). On SCV systems ensure that the SCV-A172 anti-vibration mount and SCV-
A170 cable bracket assembly are correctly fitted. Connectors Ensure all connectors are correctly and securely fitted. Cabling Ground/
Earth Testing Clear the working area SCV/ SxV Packing/
transit case Warranty card Check that all cables are safety restrained, cannot present a hazard and that the cables do not place undue strain on connectors. Test the impedance of the grounding/ earth connection between the SCV/ SxV and the platform ground. For the test procedure, please refer to the Earth bonding and continuity tests detailed in the panned maintenance section (section 11). Where possible, confirm the SCV/ SxV is fully operational prior to handing the system over to the customer. Ensure that all unused materials such as unused cables, wire cuttings etc. are tidied away and are safely disposed of. All working areas used shall be left clean and tidy. The main packing case (Part No. PP-7226) used to deliver the SCV or SxV must be retained. This case must be re-used if returning a unit to Kelvin Hughes. All other packaging should be disposed of in accordance local regulations. On completion of an installation the warranty card must be completed and returned to Kelvin Hughes Ltd; postal details are shown on the warranty card. ALL relevant sections of the warranty card check list must be completed. If an inspection on the warranty card checklist is NOT ticked it is assumed that the installation engineer has NOT carried out the inspection. Costs incurred due to attendance to repair incorrect or uninspected installations will be forwarded to the company responsible for the failure to correctly perform the work. NOTES Connectors, straps and fixings should be protected against corrosion using either suitable Denso products (or equivalent) or suitably specified halogen free, non-silicone based self-amalgamating tape that is intended for outdoor use (UV & Ozone stabilized) and in the case of SCV system a marine environment. Manufacturers instructions should be reviewed for suitability prior to application. Damage to finishes or metalwork should be made good immediately. Any damage that has occurred, including accidental dropping of the unit, must be reported to Kelvin Hughes Ltd before the unit is installed or operated. TESTING NOTES Blanking sectors should be set via the display sub-system to ensure that the SCV/SxV does not transmit into ships superstructure or an object that could potentially generate false radar returns (see section 8.3). Similarly, any Heading Line skew adjustment should be set using the display sub-
system. KH-1650-CA issue 1 Page 43 of 60 SharpEye SCV & SxV X-Band Radome Radar Chapter 9: Completion of installation 9.2 Warranty DO NOT DISMANTLE THE SCV/ SXV RADOME RADAR WARNING SharpEyeTM SCV and SxV systems are factory sealed units that contain no field serviceable, user adjustable or repairable parts. Access to components or sub-assemblies within the system is NOT required during system installation, commissioning, maintenance or operation. Opening the unit breaks the tamper and waterproof seals. Such action voids the warranty status of the unit. Please refer to Kelvin Hughes Ltd for a full list of warranty terms. TRANSIT CASE If the SCV or SxV is to be returned to Kelvin Hughes Ltd or is to be transported for any other reason, the unit must be securely packed in an upright position using the original transit packing case and its foam inserts as supplied with the equipment. Prior to use, the packing case should be examined to ensure that it is undamaged. If the transit/ packing case has been lost or is damaged please contact Kelvin Hughes Ltd. The transit packing case part number is PP-7226. KH-1650-CA issue 1 Page 44 of 60 SharpEye SCV & SxV X-Band Radome Radar Chapter 10: Operator instructions 10 Operator instructions 10.1 Switch ON and OFF Switch ON: There is no ON/ OFF power switch on the SCV or SxV radome radar. As soon as DC power is applied to the system via the external breaker or an external ON/ OFF power switch, the system enters a 30 second boot-up period during which time the SharpEyeTM processor initiates and carries out a number of self-checks. After this time the system is available for use. Switch OFF: To switch the radome radar OFF, place the system into Standby and isolate the system from the DC supply using the external breaker or external ON/ OFF power switch. Indicators: There are no power or status indicators on the SCV/ SxV system itself. 10.2 Control LAN and NETWORK SWITCHING The SharpEye SCV and SxV systems are both controlled via a Gigabit Ethernet LAN from an external command and display system.
- Radar video data (CAT240 ASTERIX), BITE data and system status messages are sent from the radome radar to the command and display system via LAN. Radar data is typically high bandwidth data and as such requires a Gigabit Ethernet network
- Control signals are received by the radome radar via the same Ethernet cable.
- Any switches used with the SCV/ SxV must support Gigabit Ethernet (1000 Base-T) and IGMP snooping. SCV/SxV OPERATOR CONTROLS There are no operator controls or user functions located on or within the radome radar itself. KELVIN HUGHES DISPLAY CONTROL For Kelvin Hughes systems please refer to the following handbooks:
HBK-4001-1 MantaDigital systems:
HBK-2300-1 CxEye integrated mast camera systems: NCD-22590 Kelvin Hughes Navigation Display:
The operation of third party external command & display systems are not detailed in this handbook. Please refer to the manufacturers operator handbooks supplied with the equipment for instructions. 10.3 Elevation beamwidth Due to the beamwidth of the antenna, target detection will be significantly reduced if the SCV/ SxV assembly is tilted by more than 12.5 from horizontal/ flat. 10.4 Performance monitoring The SharpEyeTM transceiver processor fitted within the factory sealed unit constantly monitors the systems performance and will advise operators through warnings and alarms of any errors or performance related issues. KH-1650-CA issue 1 Page 45 of 60 SharpEye SCV & SxV X-Band Radome Radar Chapter 10: Operator instructions 10.5 Operational states The following tables shows the basic operation states for the SharpEyeTM SCV or SxV radome radar Operational mode OFF Switch ON/
Standby RUN Low Power Mode Fault Mode Description DC power is OFF. The system is switched OFF and cannot be operated. No data is sent via LAN. DC power is ON No RUN command is being received. At initial power up the system enters a 30 second initialisation period. The SharpEyeTM processor carries out internal performance checks. After the initialisation period the system enters a standby state waiting for a RUN command via LAN from the external command and display system. The SharpEyeTM processor continues to monitor the system performance. System warnings and BITE data are sent via LAN to the external command and display system. If a system critical condition is detected, a warning is sent via LAN to the external command and display system and the system cannot be placed into Run mode. DC power is ON. A RUN command has been received. The system starts transmitting. Radar data is sent to the external command and display system via the LAN. The SharpEyeTM processor continues to monitor the system performance. System warnings and BITE data are sent via LAN to the external command and display system. If a system critical condition is detected, a warning is sent via LAN to the external command and display system and the system reverts to standby. DC power is ON. A RUN command has been received. Operator selected: When the SCV/ SxV radome radar is connected to a processor/ display option that supports radar radome configuration, Low Power Mode can be selected for counter surveillance or covert operation. Fault mode: Should the radome radar detect an internal fault condition which could lead to early failure of the transceiver, i.e. a high VSWR, then the transceiver switches to a Low Power state which permits low power transmission to continue in the short term. The built in test monitoring also outputs a Low RF Power warning message if the RF power output falls below 12 W. The design is fail-
soft thereby providing graceful degradation in the event of single or multiple transistor failures. As a result of reduced output power, range performance will be reduced and the system may not meet the expected operational detection performance. DC power is ON. A RUN command has been received. The system has detected an internal processor fault condition and cannot be operated. See corrective maintenance for rectification action. KH-1650-CA issue 1 Page 46 of 60 SharpEye SCV & SxV X-Band Radome Radar Chapter 10: Operator instructions Operational mode Note Description Low / High power can be selected. Low power may be used in close waters or in a high clutter environment where a high output power may produce excessive unwanted reflections from buildings, bridges and vessels. The transceiver will utilise the frame pattern for the selected range mode but with the output power reduced from the nominal 80W (49dBm) to approximately 12W
(typical) 39.5 to 42.5dBm. CAUTION As a result of reduced output power, range performance will be reduced. When low power is selected, a low power status is automatically generated to advise the operator that the system is operating at a reduced output power. Where the SharpEye detects a VSWR or a high temperature within the transceiver the system automatically switches to low power mode and generates system alarms. 9 channels are available at 9.22 to 9.38 GHz in 20MHz steps. 6, 12 and 24NM range modes can be selected These provide continuous video from the SCV/ SxVs minimum range out to the stated range. Each mode utilises slightly different processing and different pulse patterns. It is generally preferable for the operator to use the lowest range mode which provides sufficient range for the task they are trying to achieve. In some instances additional radar modes are available, please contact Kelvin Hughes Ltd for further information. Power Modes Available frequencies Range Mode BIT
(Built in Test) status Depending on the communications interface in use, BIT data may be available indicating the status of the SCV/ SxV. A list of BIT data is available from Kelvin Hughes upon request. Note: Selection and control of the modes described above is dependent on the display sub-system compatibility with the SCV/ SxV. KH-1650-CA issue 1 Page 47 of 60 SharpEye SCV & SxV X-Band Radome Radar Chapter 10: Operator instructions Page intentionally blank KH-1650-CA issue 1 Page 48 of 60 SharpEye SCV & SxV X-Band Radome Radar Chapter 11: Planned maintenance 11 Planned maintenance This section provides information on the recommended maintenance tasks for the Kelvin Hughes Ltd SharpEye SCV & SxV transceiver systems. HEALTH AND SAFETY All Health & Safety warnings noted at the beginning of this handbook must be observed at all times when inspecting the system. ADVERSE WEATHER CONDITIONS It is recommended that the mounting bolts inspections are carried out at the earliest safe opportunity after the system has been exposed to severe or adverse weather conditions, high impacts or severe vibrations. ISOLATE THE SYSTEM Prior to carrying out any system inspection or maintenance procedure, the system must be fully isolated from the DC supply using the external DC breaker. DO NOT DISMANTLE THE RADOME SharpEyeTM SCV and SxV systems are factory sealed units that contain no field serviceable or repairable parts. Access to components or sub-assemblies within the system is NOT required during installation, maintenance or operation. Opening the unit breaks tamper and waterproof seals and voids the warranty status of the unit. WARNING CASING TEMPERATURE extremely hot. When the system has been operating in strong sunlight or elevated temperatures, the casing surfaces may be At ambient temperatures exceeding +50C, the SCV/ SxV baseplate temperature can exceed +70C. MAINTENANCE RECORD This section has been designed to be printed, completed and retained as a maintenance record. Please contact Kelvin Hughes Ltd for instructions is one of the tests detailed in the above procedures fails. MAINTENANCE PROCEDURES Isolate the system:
Prior to carrying out any maintenance, the system must be fully isolated from the DC supply using the external DC breaker. Carry out the maintenance tasks:
Restore power and test. The required maintenance tasks should be undertaken. On completion of the maintenance tasks, the power should be restored and the system fully tested. Any damage that is identified as part of an inspection should immediately be reported to Kelvin Hughes Ltd and appropriate action taken to prevent further damage occurring. KH-1650-CA issue 1 Page 49 of 60 SharpEye SCV & SxV X-Band Radome Radar Chapter 11: Planned maintenance ROUTINE MAINTENANCE SCHEDULE The scheduled for routine maintenance will vary depending on the application and location of the equipment as indicated below:
HIGH SHOCK OR VIBRATION SEMI-STATIC OR MOBILE FREQUENT CHECKS INSTALLATION INFREQUENT CHECKS STATIC ROUTINE PLANNED MAINTENANCE RECORD SHEET Task Description Ensure the radome is clean and free from dirt. As necessary Clean the radome with a soft cloth moistened in a mild non-abrasive alcohol free soap solution. Cleaning Physical inspection Earth bonding and continuity Ensure that all fasteners retaining the system are tight, are secure and show no signs of damage. Note 1 Ensure that the DC power and LAN connections are securely connected and restrained. The system should be checked to ensure there is no obvious external damage, cracks or splits in the housing or potential fault conditions that could lead to a general failure of any part of the system. Note Ensure that the earth bonding nuts and bolts are tight and free from corrosion. If corrosion is present, clean and re-terminate. Note Test the earth bonding conductivity by attaching one lead of the test equipment to earth/ chassis and the other to the M6 earth stud on the radome radar. Note 2 Check earth bonding for continuity. The resistance should not exceed 0.1 ohms. If a test fails, investigate the bonding, rectify and retest. Passed Inspected By Name print & sign Date
(dd/mm/yyyy) Note 1: Over time, some white discolouration of the fasteners provided in the fitting kit is normal. This is due to the sacrificial zinc plating and not an indication of the stainless steel bolt rusting. Note 2: Safety ohmmeter, bridge Megger or Multimeter for testing the earth bonding. KH-1650-CA issue 1 Page 50 of 60 SharpEye SCV & SxV X-Band Radome Radar Chapter 11: Planned maintenance SharpEye SCV 3-MONTHLY PLANNED MAINTENANCE RECORD SHEET System Serial number Inspection date
(dd/ mm/ yyyy) SharpEye SxV Inspected by Print:
Sign:
Tools required Skill level Inspection time Task Cleaning Physical inspection Earth bonding and continuity Mild non-abrasive alcohol free detergent Soft abrasive free cloth Safety ohmmeter, Bridge Megger or multimeter Basic electrical training, good understanding of Health & Safety practices Less than 30 minutes depending on equipment location and accessibility. Description Clean the radome with a soft cloth moistened in a mild non-
abrasive alcohol free soap solution. Cleaning the radome is important as system performance can be degraded if the transmission face becomes obscured by salt deposits or dirt. The radome must never be painted. Ensure that all fasteners retaining the system are tight, secure and show no signs of severe corrosion or damage. Inspect the system including the mounting points and (where fitted) the anti-vibration mounts for any signs of stress damage. Adverse conditions: This inspection should be carried out at the earliest safe opportunity after the system has been exposed to severe or adverse weather conditions, high impacts or severe vibrations. Check that the DC power and LAN cable connections are securely fastened and appear to be watertight. Check all accessible or exposed cables for signs of damage and ensure they are safely secured into/ onto cable trays or trunking. Check that the Immersible breather located on the base of the transceiver is clean and not obscured by dirt. Caution: Do not insert sharp or pointed objects into the immersible breather as this will damage the seal. The system should be checked to ensure there is no obvious external damage, cracks or splits in the housing or potential fault conditions that could lead to a general failure of any part of the system. Ensure that the earth bonding nuts and bolts are tight and free from corrosion. If corrosion is present, clean and re-terminate Test the earth bonding conductivity by attaching one lead of the test equipment note to earth/ chassis and the other to the M6 earth stud on the radome radar. Check earth bonding for continuity. The resistance should not exceed 0.1 ohms. If a test fails, investigate the bonding, rectify and retest. Note: Safety ohmmeter, Bridge Megger or Multimeter. Pass Fail Not fitted KH-1650-CA issue 1 Page 51 of 60 SharpEye SCV & SxV X-Band Radome Radar Chapter 11: Planned maintenance Page intentionally blank KH-1650-CA issue 1 Page 52 of 60 SharpEye SCV & SxV X-Band Radome Radar Chapter 12: Corrective maintenance 12 Corrective maintenance Fault finding the SharpEye SCV and SxV radome radar is limited to:
Resetting the system Ensuring that the DC input voltage is within acceptable limits Troubleshooting using the procedures noted in this section of the handbook. There are no external power or status indicators on the radome radar. DO NOT DISMANTLE THE SCV/ SxV RADOME RADAR SCV and SxV systems are factory sealed units that contain no field serviceable or repairable parts. Opening the unit breaks tamper and waterproof seals and voids the warranty status of the unit. 12.1 System reset In the unlikely event of a system freeze, system lock up or an error message, the system may need to be reset as follows:
SWITCH TO STANDBY: Where possible switch the system to standby using the external command SWITCH OFF:
SWITCH BACK ON:
and display system. Using the external breaker or external ON/ OFF power switch, isolate the DC power to the system and leave in an unpowered state for approximately 1 minute. This allows for any residual power in the system to drain away. Using the external breaker or external ON/ OFF power switch restore the DC power to the system and test. If the fault condition persists please contact Kelvin Hughes Ltd for assistance. 12.2 Repair and return The SCV/ SxV radome radar is a Line Replacement Unit that contains no field serviceable or repairable parts. The complete sealed radome radar must be returned to Kelvin Hughes for analysis. In line with our product returns policy, If the SCV or SxV is to be returned to Kelvin Hughes Ltd or is to be transported for any other reason, the unit must be securely packed in an upright position using the original transit packing case and its foam inserts as originally supplied with the equipment. Prior to use, the packing case should be examined to ensure that it is undamaged. If the transit/
packing case has been lost or it is damaged, please contact Kelvin Hughes Ltd. KH-1650-CA issue 1 Page 53 of 60 SharpEye SCV & SxV X-Band Radome Radar Chapter 12: Corrective maintenance 12.3 Troubleshooting Loss of video and/ or Loss of status messages System showing Video and/ or status messages but, interference or poor returns are present on the display sub-system Fault reporting If video ceases to be displayed and the SCV/ SxV is installed in a position where a person can be within 15m of the antenna, as a precautionary measure the operator should cease transmission immediately and investigate the problem. Transmission can be stopped by switching the SCV/ SxV system OFF. This ensures that if the antenna has ceased rotation under fault conditions in such a position that it is facing a person and further software faults occur, nobody is accidentally irradiated in excess of the safe limits. If the system fails to communicate after the initialisation period, isolate the power to the system and ensure that both the DC and LAN cables are securely connected and free from damage. Check that the DC voltages being supplied to the system are within acceptable limits. If the system randomly resets or is temporarily unavailable, check that the DC input to the system is stable under load conditions and does not drop below the recommended minimum DC input level noted in section 13.3. Standard network diagnostic tools and software may be used to ensure data is being output from the SCV LAN connection. If the system operates on a network, try connecting the SCV directly to the display from the LAN cable or diagnostic tools. Ensure that there are no objects in the immediate vicinity of the system that may be blocking or reflecting RF radiation back towards the radome. If this is unavoidable, ensure that a blanking sector has been correctly configured to cover the affected area (please refer to section 4 regarding blanking sectors). It may be necessary to cover the objects with Radar Absorbent Material (RAM) to attenuate unwanted reflections. Where the display software permits:
1. Change the SharpEye transmission frequency. If the problem disappears it may be being caused by interference from other transmitters in the local vicinity. 2. Change the SharpEye power from High to Low power. Return the system to High power on completion of any tests. 3. Mute the system on each available range mode and see if any interference remains on screen. If a mute feature is not available, set a blanking sector that covers the area of interference or the whole display are (i.e. 360). If a problem persists and cannot be resolved, please contact Kelvin Hughes Ltd with the following details:
1. FAULT CONDITION: Describe the condition being experienced, the modes or control commands that cause the issue and any error messages that have been observed. 2. BIT DATA: If the communications interface in use can display BIT data from the SCV/ SxV, please advise the messages being displayed. A full list of BIT data is available from Kelvin Hughes upon request. 3. SCREEN GRABS: Where permissible and where the display software permits, take screen shots of the display showing the affected video. If there is no screen grab facility take a photograph or a short video. Photographs or diagrams of the installation, where permissible, may also prove useful. INTERFERENCE: If the issue relates to an object that cannot be observed on screen, describe the object, its distance from the radar and any other conditions (e.g. metrological) that may have an impact on target detection. 4. KH-1650-CA issue 1 Page 54 of 60 SharpEye SCV & SxV X-Band Radome Radar Chapter 13: Specifications 13 Specifications 13.1 Mechanical specifications Dimensions Weights Radome colour SCV 586mm x 338mm high (includes anti-vibration mounts and cable bracket) SxV 586mm x 292mm high SCV SCV-A1-10-****: 20kg approximately SCV-A170 cable bracket: 421g SCV-A172 Anti-Vibration mount: 2Kg Packing SxV 20kg approximately case 11Kg approximately (packing case part No. PP-7226) Black as standard but other colours such as white, sand and olive can be obtained by special order 13.2 Environmental specifications Operating Temperature EXTENDED Operating Temperature Storage Temperature Storage &
Packing
-25C to +55C ambient temperature including solar heating Up to 95% relative humidity at +40C Note: At low temperatures it is recommended the Radome radar is left powered in standby or RUN mode.
-25C to
-40C The radome radar must remain switched ON in standby or RUN mode when exposed to or operating at temperatures between -25C to -40C. It is recommended that systems that are switched OFF and exposed to temperatures between -25C to -40C are not switched ON or operated until the unit has returned to temperatures above -25C for 8 hours or WARNING more.
-40C to +70C Up to 95% relative humidity at +40C Equipment being stored prior to installation or delivery must be kept in its original packing. When opened or after any inspection all equipment must be repacked in an upright positon using the original packing material supplied by Kelvin Hughes Ltd. Shipping clearances and Special Packing Instruction conditions may be void if the equipment is unpacked. Note 1 Storage Environment Equipment must be stored in its original packing in a well-ventilated, dry building or warehouse that provides protection from extremes of temperature, the weather, rodent and insect infestation. Shelf Life Note 2 If no DC power is applied to the equipment for a long period there is a risk that the performance of large capacity electrolytic capacitors can decline. When leaving equipment unused for a long time, it is recommended that the system is powered up once every two years and is left switched ON in a standby state for a minimum of 5 hours. Where possible and whilst switched ON, the basic functions of the system should be checked to ensure that the system is operational. Note 1: Please refer to section 12.2 for details on packing and returning a unit. Note 2: The long term storage test procedures for equipment are not defined in this document. Please contact Kelvin Hughes for specific instructions on packing, re-packing, powering and testing of systems. KH-1650-CA issue 1 Page 55 of 60 SharpEye SCV & SxV X-Band Radome Radar Chapter 13: Specifications 13.3 Transceiver specifications DC POWER REQUIREMENTS DC input DC power cable
+24VDC DC range: +19.5VDC to 30VDC measured at the unit under maximum load conditions Standard systems use 10 metre DC power cables. If additional DC cabling is required, the cable must be of a sufficient gauge to ensure that the minimum voltage required by the SCV/ SxV is maintained under the worst case load conditions. The cable must designed to ensure that the voltage drop along the cable never causes the DC supply measured at the SCV/ SxV power connector to fall below +19.5VDC under maximum load conditions. For cable runs longer than 10m, Kelvin Hughes recommend a DC supply of at least +28VDC and/ or a cable and DC supply that supports sensing lines. DC Power 150W typical, 250W peak Breaker/ fuse rating 10A @ 24VDC breaker SharpEye RADOME RADAR Transmission frequency Frequency Bandwidth PRF Processing Peak RF power Measured at the output of the SharpEye prior to the antenna ERP
(Effective Radiated Power) Pulse duty cycle X-band transmission with 9 LAN configurable frequencies between 9.22GHz to 9.38Ghz in steps of 0.02GHz 20MHz 1 4.5KHz depending on mode Pulse compression and coherent Doppler processing High power 50 to 80W (typical) 47 to 50dBm
(in normal operation) Peak radiated power (ERP) = 42dBW Mean radiated power (ERP) = 33dBW 13% maximum (hardware limited) Low Power 12W (typical) 39.5 to 42.5dBm Range scales 6, 12, 24Nm Blanking (mute) Three mute (blanking) and one True. ANTENNA Size Beamwidth 530mm horizontally polarised planar array 20 to 22 vertical, < 3.9 azimuth Note: Due to the beamwidth of the antenna, target detection will be significantly reduced if the SCV/ SxV assembly is tilted by more than 10 from horizontal/ flat. Tilt Gain Rotation speed No tilt 0 with respect to mounting points (horizontal) 20 22dBi 12RPM or 24RPM dependent of range scale and software installed. Please contact Kelvin Hughes Ltd for further information. KH-1650-CA issue 1 Page 56 of 60 SharpEye SCV & SxV X-Band Radome Radar Chapter 13: Specifications EXTRANAL INTERFACES The LAN connection provides control (CAT253 ASTERIX format), and radar video (CAT240 ASTERIX format). The specification for the ASTRIX CAT240 video LAN output and protocol is available on request. Please contact Kelvin Hughes for additional details including system integration information. Where required, network switches must support Gigabit Ethernet (1000 Base-T) and IGMP snooping. Position and direction information can be outputted from the SCV/ SxV via the LAN in a UDP message format. The data provided is for reference use only and cannot be used as a primary source of navigation data. GGA, GSA, GSV, RMC, VTG, ZDA, GLL and HDG outputs are available. Pitch and roll data is also available in a XDR format. Sensor data is not enabled by default. Please contact Kelvin Hughes Ltd for details on system integration and the system configuration. LAN connection INTERNAL SENSOR Position, heading, pitch and roll data 13.4 Approvals All Kelvin Hughes Ltd designed equipment is designed and manufactured to Kelvin Hughes own standards of practice and is also designed to meet the applicable requirements of the following directives:
Vibration & Shock Designed to meet IEC 60945 Climatic Designed to meet IEC 60945 Ingress Protection Protected to IP67 (dust tight and up to 1.0m water depth) EMC Designed to meet ETSI EN302248 V1.1.2 (2005-06) and IEC 60945 KH-1650-CA issue 1 Page 57 of 60 SharpEye SCV & SxV X-Band Radome Radar Chapter 13: Specifications Page intentionally blank KH-1650-CA issue 1 Page 58 of 60 SharpEye SCV & SxV X-Band Radome Radar Chapter 14: Contact details 14 Contact details Kelvin Hughes Limited 6 Mollison Avenue Voltage Enfield EN3 7XQ United Kingdom Phone:
Fax:
+44 (0)1992 805 200
+44 (0) 1992 805 310 Service Technical Advice Spares email service@kelvinhughes.co.uk Phone
+44 (0)1992 805 301 email technical.advice@kelvinhughes.co.uk Phone
+44 (0)1992 805 302 email spares@kelvinhughes.co.uk Phone
+44 (0)1992 805 301 Internet Website www.kelvinhughes.com KH-1650-CA issue 1 Page 59 of 60 Kelvin Hughes Ltd Voltage, 6 Mollison Avenue Enfield, EN3 7QX, United Kingdom Tel: +44 (0) 1992 805200 Fax: +44(0) 1992 805310 WWW.kelvinhughes.com SITUATIONAL AWARENESS, THE WORLD OVER
| frequency | equipment class | purpose | ||
|---|---|---|---|---|
| 1 | 2018-01-11 | 9200 ~ 9400 | MRD - Marine Radar | Original Equipment |
| app s | Applicant Information | |||||
|---|---|---|---|---|---|---|
| 1 | Effective |
2018-01-11
|
||||
| 1 | Applicant's complete, legal business name |
Kelvin Hughes Limited
|
||||
| 1 | FCC Registration Number (FRN) |
0019158021
|
||||
| 1 | Physical Address |
Voltage
|
||||
| 1 |
Enfield, N/A EN3 7XQ
|
|||||
| 1 |
United Kingdom
|
|||||
| app s | TCB Information | |||||
| 1 | TCB Application Email Address |
T******@TIMCOENGR.COM
|
||||
| 1 | TCB Scope |
B3: Maritime & Aviation Radio Services equipment in 47 CFR parts 80 & 87
|
||||
| app s | FCC ID | |||||
| 1 | Grantee Code |
CIC
|
||||
| 1 | Equipment Product Code |
SXV-A1
|
||||
| app s | Person at the applicant's address to receive grant or for contact | |||||
| 1 | Name |
T******** A********
|
||||
| 1 | Title |
Chief Engineer
|
||||
| 1 | Telephone Number |
44199********
|
||||
| 1 | Fax Number |
44199********
|
||||
| 1 |
t******@kelvinhughes.co.uk
|
|||||
| app s | Technical Contact | |||||
| n/a | ||||||
| app s | Non Technical Contact | |||||
| n/a | ||||||
| app s | Confidentiality (long or short term) | |||||
| 1 | Does this application include a request for confidentiality for any portion(s) of the data contained in this application pursuant to 47 CFR § 0.459 of the Commission Rules?: | Yes | ||||
| 1 | Long-Term Confidentiality Does this application include a request for confidentiality for any portion(s) of the data contained in this application pursuant to 47 CFR § 0.459 of the Commission Rules?: | No | ||||
| if no date is supplied, the release date will be set to 45 calendar days past the date of grant. | ||||||
| app s | Cognitive Radio & Software Defined Radio, Class, etc | |||||
| 1 | Is this application for software defined/cognitive radio authorization? | No | ||||
| 1 | Equipment Class | MRD - Marine Radar | ||||
| 1 | Description of product as it is marketed: (NOTE: This text will appear below the equipment class on the grant) | X BAND RADAR | ||||
| 1 | Related OET KnowledgeDataBase Inquiry: Is there a KDB inquiry associated with this application? | No | ||||
| 1 | Modular Equipment Type | Does not apply | ||||
| 1 | Purpose / Application is for | Original Equipment | ||||
| 1 | Composite Equipment: Is the equipment in this application a composite device subject to an additional equipment authorization? | No | ||||
| 1 | Related Equipment: Is the equipment in this application part of a system that operates with, or is marketed with, another device that requires an equipment authorization? | No | ||||
| 1 | Grant Comments | Output power listed is conducted. | ||||
| 1 | Is there an equipment authorization waiver associated with this application? | No | ||||
| 1 | If there is an equipment authorization waiver associated with this application, has the associated waiver been approved and all information uploaded? | No | ||||
| app s | Test Firm Name and Contact Information | |||||
| 1 | Firm Name |
Timco Engineering, Inc.
|
||||
| 1 | Name |
B****** C********
|
||||
| 1 | Telephone Number |
352-4********
|
||||
| 1 | Fax Number |
352 4********
|
||||
| 1 |
b******@timcoengr.com
|
|||||
| Equipment Specifications | |||||||||||||||||||||||||||||||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| Line | Rule Parts | Grant Notes | Lower Frequency | Upper Frequency | Power Output | Tolerance | Emission Designator | Microprocessor Number | |||||||||||||||||||||||||||||||||
| 1 | 1 | 80,90 | BF | 9200.00000000 | 9400.00000000 | 103.8000000 | 1250.0000000000 ppm | 13M8P0N | |||||||||||||||||||||||||||||||||
some individual PII (Personally Identifiable Information) available on the public forms may be redacted, original source may include additional details
This product uses the FCC Data API but is not endorsed or certified by the FCC