96M13982 Safety Precautions on Laser Product This product employs a semiconductor laser for its light source. Handheld Mobile Computer BT-W100GA/W155GA Instruction Manual Item Wavelength Output Laser Class BT-W100GA BT-W155GA 655 nm 1.0 mW 655 nm 390 W Class 2 laser product
(IEC60825-1, Class 1 laser product
(IEC60825-1, FDA(CDRH) Part 1040.10*) FDA(CDRH) Part 1040.10*)"
* The laser classification for FDA(CDRH) is implemented based on IEC60825-1 in accordance with the requirements of Laser Notice No.50. Follow the instructions mentioned in this manual. Otherwise, injury to the human body
(eyes and skin) may result. Introduction Read this instruction manual before using the product in order to achieve maximum performance. Keep this instruction manual in a safe place after reading it so that it can be used at any time. In this instruction manual, the BT-W100GA Series means the BT-W100GA and BT-W155GA. WARNING
Symbols The following symbols alert you to important messages. Be sure to read these messages carefully. DANGER WARNING CAUTION NOTICE It indicates a hazardous situation which, if not avoided, will result in death or serious injury. It indicates a hazardous situation which, if not avoided, could result in death or serious injury. It indicates a hazardous situation which, if not avoided, could result in minor or moderate injury. It indicates a situation which, if not avoided, could result in product damage as well as property damage. Important It indicates cautions and limitations that must be followed during operation. Point It indicates additional information on proper operation. Reference It indicates tips for better understanding or useful information. IEEE802.11a/b/g/n: Wireless LAN standards established by 802 committee which has designed standards of LAN technology in IEEE (Institute of Electrical and Electronics Engineers). Bluetooth wordmark and logo belong to Bluetooth SIG, Inc. and KEYENCE uses them under license. Other trademarks or trade names belong to each owner. microSDTM is a trademark of SD Card Association. Microsoft, Windows, Internet Explorer and Visual Studio are registered trademarks or trademarks of Microsoft Corporation in the United States and other countries. The official name for Windows is "Windows operating system". ARM Cortex is a trademark and registered trademark of ARM Limited in EU and other countries. Other company names or product names described in this manual are registered trademarks or trademarks of each company. It is prohibited to use or copy all or any part of this manual without prior approval. The information contained in this manual is subject to change without notice. Safety Information for the BT-W100GA Series
General cautions Do not use this product for the purpose of protecting a human body or a part of human body. DANGER This product is not intended for use as an explosion-proof product. Do not use this product in a hazardous location and/or potentially explosive atmosphere. Suffocation may result from wrapping the lanyard around the neck. Be careful to use BT-W100GA around a power-driven machine on work. Verify that this device is operating normally in terms of functionality and performance before the start of work and when operating the device. We recommend that you take substantial safety measures to avoid any damage in the event that a problem occurs. CAUTION If the equipment is used in a manner not specified by the manufacturer, the protection provided by the equipment may be impaired. Do not throw, drop or trample down the BT-W100GA Series and accessories to strong physical shock. Keep BT-W100GA Series or accessories out of the reach of children. Children may swallow batteries, batteries attachment covers and straps around themselves. NOTICE When the BT-W100GA Series is used in combination with other instruments, functions and performance may be degraded, depending on operating conditions and the surrounding environment. The LCD panel may generate microscopic spots (black/bright spot), uneven brightness or crosstalk (phenomenon that non-existent lines or patterns are displayed), depending on the conditions. If the same display remains on the screen for a long time, afterimage may occur due to the characteristics of LCD. Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure. Do not disassemble this product. Laser emission from this product is not automatically stopped when it is disassembled. Class 1 Laser Product Do not stare into the direct or specularly reflected beam. Class 2 Laser Product Do not stare into the direct or specularly reflected beam. Do not direct the beam at other people or into areas where other people unconnected with the laser work might be present. Be careful of the path of the laser beam. If there is a possibility that the operator may be exposed to the specular or diffuse reflections, block the beam by installing a protective enclosure. Install this product so that the path of the laser beam is not as the same height as that of human eye. Safety Precautions on LED Product Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure. Follow the instructions mentioned in this manual. Otherwise, injury to the human body (eyes and skin) may result. Do not stare into the beam. Do not disassemble this product. CAUTION LED emission from this product is not automatically stopped when it is disassembled. Do not view directly with optical instruments. Viewing the LED output with certain optical instruments (for example, eye loupes, magnifiers and microscopes) within a distance of 100 mm may pose an eye hazard.
Locations of warning / explanation labels BT-W100GA Scanner
(Laser emission part) BT-W155GA Scanner
(Laser emission part) 1 E BT-W100GA/W155GA-IM Precautions on Regulations and Standards
FCC Regulations This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions; (1) This device may not cause harmful interface, and (2) this device must accept any interference received, including interference that may cause undesired operation. Application regulation FCC Part 15 Subpart B ClassA FCC Part 15 Subpart C FCC Part 15 Subpart E The available scientific evidence does not show that any health problems are associated with using low power wireless devices. There is no proof, however, that these low power wireless devices are absolutely safe. Low power Wireless devices emit low levels of radio frequency energy (RF) in the microwave range while being used. Whereas high levels of RF can produce health effects (by heating tissue), exposure of low-level RF that does not produce heating effects causes no known adverse health effects. Many studies of low-level RF exposures have not found any biological effects. Some studies have suggested that some biological effects might occur, but such findings have not been confirmed by additional research. The BT-W100GA Series has been tested and found to comply with FCC radiation exposure limits set forth for an Controlled environment and meets the FCC radio frequency (RF) Exposure Guidelines. Compliance with FCC requirement 15.407(c) Data transmission is always initiated by software, which is the passed down through the MAC, through the digital and analog baseband, and finally to the RF chip. Several special packets are initiated by the MAC. These are the only ways the digital baseband portion will turn on the RF transmitter, which it then turns off at the end of the packet. Therefore, the transmitter will be on only while one of the aforementioned packets is being transmitted. In other words, this device automatically discontinue transmission in case of either absence of information to transmit or operational failure. 5.15-5.35GHz band is restricted to indoor operations only. Frequency Tolerance: 25ppm CAUTION Note: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. FCC CAUTION Changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. This transmitter must not be co-located or operated in conjunction with any other antenna or transmitter.
IC Regulations The BT-W100GA Series complies with the following regulations specified by the IC. Applicable regulation ICES-003 RSS-247 The available scientific evidence does not show that any health problems are associated with using low power wireless devices. There is no proof, however, that these low power wireless devices are absolutely safe. Low power Wireless devices emit low levels of radio frequency energy (RF) in the microwave range while being used. Whereas high levels of RF can produce health effects (by heating tissue), exposure of low-level RF that does not produce heating effects causes no known adverse health effects. Many studies of low-level RF exposures have not found any biological effects. Some studies have suggested that some biological effects might occur, but such findings have not been confirmed by additional research. The BT-W100GA Series has been tested and found to comply with IC radiation exposure limits set forth for an uncontrolled environment and meets RSS-102 of the IC radio frequency (RF) Exposure rules. 5150-5350 MHz band is restricted to indoor operation only. High-power radars are allocated as primary users (i.e. priority users) of the bands 5250-5350 MHz and 5650-5850 MHz and that these radars could cause interference and/or damage to LE-LAN devices. Data transmission is always initiated by software, which is the passed down through the MAC, through the digital and analog baseband, and finally to the RF chip. Several special packets are initiated by the MAC. These are the only ways the digital baseband portion will turn on the RF transmitter, which it then turns off at the end of the packet. Therefore, the transmitter will be on only while one of the aforementioned packets is being transmitted. In other words, this device automatically discontinue transmission in case of either absence of information to transmit or operational failure. Les connaissances scientifiques dont nous disposons nont mis en vidence aucun problme de sant associ lusage des appareils sans fil faible puissance. Nous ne sommes cependant pas en mesure de prouver que ces appareils sans fil faible puissance sont entirement sans danger. Les appareils sans fil faible puissance mettent une nergie radiolectrique (RF) trs faible dans le spectre des micro-ondes lorsquils sont utiliss. Alors quune dose leve de RF peut avoir des effets sur la sant
(en chauffant les tissus), lexposition de faibles RF qui ne produisent pas de chaleur na pas de mauvais effets connus sur la sant. De nombreuses tudes ont t menes sur les expositions aux RF faibles et nont dcouvert aucun effet biologique. Certaines tudes ont suggr quil pouvait y avoir certains effets biologiques, mais ces rsultats nont pas t confirms par des recherches supplmentaires. Le BT-W100GA srie a t test et jug conforme aux limites dexposition aux rayonnements nonces pour un environnement non contrl et respecte les rgles dexposition aux frquences radiolectriques (RF) CNR-102 de lIC. La bande 5150-5350 MHz est restreinte une utilisation lintrieur seulement. Les radars de haute puissance sont dsigns utilisateurs principaux (c.--d., qu'ils ont la priorit) pour les bandes 5250-5350 MHz et 5650-5850 MHz, et ces radars pourraient causer du brouillage et/ou des dommages aux dispositifs LAN-EL. Conformit la norme CNR-210 A9.4.4 La transmission des donnes est toujours initie par le logiciel, puis les donnes sont transmises par l'intermdiaire du MAC, par la bande de base numrique et analogique et, enfin, la puce RF. Plusieurs paquets spciaux sont initis par le MAC. Ce sont les seuls moyens pour qu'une partie de la bande de base numrique active l'metteur RF, puis dsactive celui-ci la fin du paquet. En consquence, l'metteur reste uniquement activ lors de la transmission d'un des paquets susmentionns. En d'autres termes, ce dispositif interrompt automatiquement toute transmission en cas d'absence d'information transmettre ou de dfaillance. This device complies with Industry Canadas licence-exempt RSSs. Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. CAUTION Le prsent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorise aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible d'en compromettre le fonctionnement.
UL certification The BT-W100GA Series complies with the following UL/CSA standards and has obtaied the UL/C-UL certifications. Applicable standards UL60950-1 UL File No. E167973 UL category NWGQ/NWGQ7 CAUTION RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE. DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS.
Mexico(Mjico) La operacin de este equipo est sujeta a las siguientes dos condiciones: (1) es posible que este equipo o dispositivo no cause interferencia perjudicial y (2) este equipo o dispositivo debe aceptar cualquier interferencia, incluyendo la que pueda causar su operacin no deseada. E BT-W100GA/W155GA-IM 2
Precautions on wireless LAN and Bluetooth WARNING WARNING Important Remove the main battery of the BT-W100GA Series near locations where using wireless devices is banned at medical institutions or near electric devices for medical purposes. Carry and use the product away from an implanted cardiac pacemaker. The BT-W100GA Series uses the radio wave of 5GHz band, and can 5.2GHz band (W52), 5.3GHz band (W53), 5.6GHz band (W56) and 5.8GHz band (W58). Using 5.2GHz band (W52) and 5.3GHz band
(W53) outdoors is prohibited by Radio Act. Retirez la batterie principale de la srie BT-W100GA prs des endroits o l'aide d'appareils sans fil est interdite dans les tablissements mdicaux ou proximit d'appareils lectriques des fins mdicales. Transporter et utiliser le produit en dehors d'un stimulateur cardiaque implant. Srie BT-W100GA utilise l'onde radio de 5 GHz bande, et peut bande de 5,2 GHz (W52), bande de 5.3GHz (W53h), bande de 5.6GHz (W56 ) et 5,8 GHz bande (W58) utilisant la bande de 5,2 GHz (de W52) et de la bande de 5.3GHz (W53) en plein air il est interdit par la loi Radio. Depending on the environment, communication may be impossible. Check the communication availability before using. If this product is used near devices with the same frequency band, such as a wireless LAN device, microwave oven, heating equipment for industrial use, high-frequency equipment for medical use, etc., radio wave interference may occur and the communication speed will become slow or communication may become impossible. If a wireless LAN and Bluetooth are used at the same time, radio wave interference may occur and the communication speed will become slow or communication may be interrupted. If there is communication failure, stop using either the wireless LAN or Bluetooth. Communication may be impossible at locations near metallic objects, locations surrounded with metallic walls or where there is a lot of metallic powder. Possible bluetooth communication distance is approx. 10 m of vision, however, even within 10 m, communication may become impossible depending on the environment. Check the communication availability before using.
Handling of the BT-W100GA NOTICE Use within the temperature range described in Specifications (4 page). Do not leave the product inside a closed car or at a place exposed to direct sunlight. Doing so may damage to the unit. Use within the humidity range described in Specifications (4 page). Do not use the product at locations where condensation occurs due to the rapid temperature change. Doing so may damage to the unit. This is a precision instrument. Dropping this product or subjecting it to shock may cause damage. Be careful when carrying or using this unit. Do not put the BT-W100GA Series at a location with high humidity or a dusty area. Doing so may damage to the unit. Do not insert a sharp object such as a needle to the buzzer hole on the back side of the BT-W100GA Series. The water-proof sheet may be damaged. Precautions for proper use
Handling of packing NOTICE The BT-W100GA Series has an IP54 protection rating, however, if theBattery attachment cover is not properly attached, the IP54 rating cannot be guaranteed. When using in environments where water or dust is present, check if these are properly attached. Dropping the BT-W100GA Series or subjecting to extreme shock may lose water-proof feature. Handle with great care. Attaching the rechargeable battery pack Before attaching the rechargeable battery pack, make sure to check if the packing has properly been set on the main unit side of the battery pack attachment cover. Do not use batteries other than BT-WB1GA. Make sure to charge BT-WB1GA when using for the first time. Before replacing the rechargeable battery pack, be sure to turn the power of the BT-W100GA Series.
Attaching the rechargeable battery pack 1 Slide the fixed lock lever in the arrow direction (1) and remove the battery attachment cover (2).
(2)
(1) 2 Face the flat part of the new rechargeable battery pack (BT-WB1GA) inward, and align the contact polarity as shown in the illustration. From the grip side (1), push in lightly with your finger (2). 3 Align the claw of the battery attachment cover from the grip side and close (1). Slide the lock lever in the arrow direction to fix (2).
(2)
(1)
(1)
(2) Point Check that the lock lever is completely fixed. If the lock lever is not completely fixed, the battery pack may come off. NOTICE When attaching or replacing the rechargeable battery pack, be careful not to allow dust to enter inside. Contact failure may occur. This may cause charging function to deteriorate and instantaneous interruption. 3 E BT-W100GA/W155GA-IM Cleaning Specifications Clean the following parts with air blow periodically. If removing dirt is difficult, use a cotton swab to clean the contacts directly.
(Use absolute ethanol if dirt is stuck on them.) Remove the battery attachment cover before cleaning the battery contact. BT-W100GA BT-W155GA Battery contact Scanner Battery contact Scanner Charging/
communication contact Charging/
communication contact NOTICE If dirt or dust is attached, contact failure may occur on the battery/
charging/communication contacts. This may cause charging function to deteriorate and instantaneous interruption. Make sure that waste textile is not attached to the battery/charging/
communication contacts when cleaning. Operation status LED Operation part Touch panel Keyboard Number Backlight Checking the Package When opening the package, check the following items are all included. If there is something missing, product failure or damage, contact your nearest KEYENCE sales office.
BT-W100GA/W155GA Main Unit1 Hand Strap Back Cover...1 Wrist strap...1 Stylus...1 Instruction Manual...1 Item Specifications Model Scanning type Control part CPU OS RAM ROM Main memory Screen Type Resolution Color Back Light BT-W100GA Laser Type BT-W155GA Camera Type ARM Coretex-A8 (800 MHz) Microsoft Windows Embedded Compact 7 256 MB 512 MB Flash-ROM 3.5 in transmissive TFT LCD (Vertically Aligned) W 480 x H 640 (VGA) 65536 colors Super luminosity white LED tri-color LED
(red, green, blue, yellow, cyan, magenta, white) Analog resistance film (hardened glass) 26 keys LED (orange) Super luminosity red LED Visible light semiconductor laser (655 nm) Output 390 W Class 1 laser product
(IEC60825-1)
-
100 scans/second
-
0.127 mm 62 to 542 mm 2D code: 0.191 mm Barcode: 0.127 mm 35 to 270 mm
(CODE39 narrow bar width 0.508 mm) 40 to 190 mm Reading light source Visible light semiconductor laser (655 nm) Output 1.0 mW Class 2 laser product
(IEC60825-1)"
Pointer light source Scan count Minimum resolution Reading specification Scanner Reading distance
(narrow bar width 1.0 mm)
(CODE39 narrow bar width 42 to 222 mm
(narrow bar width 0.25 mm) 0.254 mm) 25 to 205 mm Reading width
(Field range)
-
0.45 or more
(QR cell size 0.508 mm) 75 to 140 mm
(QR cell size 0.254 mm) 81x 51 mm
(Reading distance 110 mm) PCS
(reflection rate of space part
-
70% or more) JAN/EAN/UPC JAN/EAN/UPC
(add-on code compatible) CODE128, GS-128,
(add-on code compatible), CODE39, NW-7, CODE93, CODE128, GS1-128, CODE39, NW-7, CODE93, ITF, Industrial2of5, COOP2of5, GS1-DataBar ITF COOP2of5, Industrial2of5 QR code, micro QR, DataMatrix
(ECC200), PDF417, GS1-DataBar, composite symbol IEEE802.11a/b/g/n 2.4 GHz (b/g/n: 1 - 11 ch) 5 GHz (a/n: W52,W53,W56,W58) W52 can only be used indoors. Indoors: 100 m of vision Security: WEP(64/128 bit)/WPA/WPA2 WPA encryption: TKIP/AES Authentication: WPA(2)-PSK /
TLS / PEAP /TTLS / LEAP / EAP-FAST Bluetooth V2.1 +EDR SPP, PAN(PANU), FTP(Client), HSP(AG), HID(Host/Device) Approx. 10 m microSD/SDHC card up to 32 GB Decoding capability Wireless communi-
cation Wireless LAN Bluetooth Wireless Radio Radio frequency range communication distance Security Wireless standard Supported profile Communica-
tion distance Expansion Slot Supported media Capacity Type Capacity Continuous usage time Charging time Clock RAM data Main battery Backup battery Buzzer Vibration function Clock accuracy Rechargeable, removable Lithium ion battery pack 2450 mAh Approx. 19 hours*1,3 Approx. 4.5 hours (at room temperature) Built-in lithium secondary battery (approx. 6 months)*2,3 Electric double layer capacitor (approx. 3 minutes)*2,3 Musical tones: 16 tones Volume: 3 levels Enable (Pattern is not variable) 80 seconds per month (at room temperature) Power source Others 4 E BT-W100GA/W155GA-IM Item Environ-
ment resis-
tance Enclosure sealing Drop resistance Operation temperature Operation humidity Storage temperature Storage humidity Dimensions () show grip parts. Weight with battery pack Accessory Specifications IP54 (IEC60529) Multiple drops to concrete: 1.5 m*3
-20
-5 to +50 C (No freezing)*4 20 to 85%RH (No condensation)
-20 to +60 C (No freezing) 20 to 85%RH (No condensation) 170 x 79 x 36.1 (31.3) mm 170 x 79 x 40.4 (31.3) mm 259 g 262 g Hand Strap Back Cover, Wrist strap, Stylus pen
*1 This indicates the case when barcodes are read once per 20 seconds and round trip wireless communication is made at room temperature with the operation status LED, vibration function OFF, the buzzer ON (low volume), the backlight ON (brightness 1) and the charging mode2.
*2 This indicates the case when the main battery is not attached or the battery level is low, and operations are performed at room temperature.
*3 This is a typical value at room temperature, but not a guaranteed value.
*4 Replace the main battery in an environment that has a temperature of -5 C or higher. The product may not start in low-temperature environments. Outline dimensional drawing
BT-W100GA 36.1 31.3
BT-W155GA 40.4 170 170 81.1 79 52.4 81.1 79 unit (mm) 31.3 52.4 unit (mm) 5 E BT-W100GA/W155GA-IM WARRANTIES AND DISCLAIMERS
(1) KEYENCE warrants the Products to be free of defects in materials and workmanship for a period of one (1) year from the date of shipment. If any models or samples were shown to Buyer, such models or samples were used merely to illustrate the general type and quality of the Products and not to represent that the Products would necessarily conform to said models or samples. Any Products found to be defective must be shipped to KEYENCE with all shipping costs paid by Buyer or offered to KEYENCE for inspection and examination. Upon examination by KEYENCE, KEYENCE, at its sole option, will refund the purchase price of, or repair or replace at no charge any Products found to be defective. This warranty does not apply to any defects resulting from any action of Buyer, including but not limited to improper installation, improper interfacing, improper repair, unauthorized modification, misapplication and mishandling, such as exposure to excessive current, heat, coldness, moisture, vibration or outdoors air. Components which wear are not warranted.
(2) KEYENCE is pleased to offer suggestions on the use of its various Products. They are only suggestions, and it is Buyer's responsibility to ascertain the fitness of the Products for Buyers intended use. KEYENCE will not be responsible for any damages that may result from the use of the Products.
(3) The Products and any samples ("Products/Samples") supplied to Buyer are not to be used internally in humans, for human transportation, as safety devices or fail-safe systems, unless their written specifications state otherwise. Should any Products/
Samples be used in such a manner or misused in any way, KEYENCE assumes no responsibility, and additionally Buyer will indemnify KEYENCE and hold KEYENCE harmless from any liability or damage whatsoever arising out of any misuse of the Products/Samples.
(4) OTHER THAN AS STATED HEREIN, THE PRODUCTS/SAMPLES ARE PROVIDED WITH NO OTHER WARRANTIES WHATSOEVER. ALL EXPRESS, IMPLIED, AND STATUTORY WARRANTIES, INCLUDING, WITHOUT LIMITATION, THE WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, AND NON-INFRINGEMENT OF PROPRIETARY RIGHTS, ARE EXPRESSLY DISCLAIMED. IN NO EVENT SHALL KEYENCE AND ITS AFFILIATED ENTITIES BE LIABLE TO ANY PERSON OR ENTITY FOR ANY DIRECT, INDIRECT, INCIDENTAL, PUNITIVE, SPECIAL OR CONSEQUENTIAL DAMAGES (INCLUDING, WITHOUT LIMITATION, ANY DAMAGES RESULTING FROM LOSS OF USE, BUSINESS INTERRUPTION, LOSS OF INFORMATION, LOSS OR INACCURACY OF DATA, LOSS OF PROFITS, LOSS OF SAVINGS, THE COST OF PROCUREMENT OF SUBSTITUTED GOODS, SERVICES OR TECHNOLOGIES, OR FOR ANY MATTER ARISING OUT OF OR IN CONNECTION WITH THE USE OR INABILITY TO USE THE PRODUCTS, EVEN IF KEYENCE OR ONE OF ITS AFFILIATED ENTITIES WAS ADVISED OF A POSSIBLE THIRD PARTYS CLAIM FOR DAMAGES OR ANY OTHER CLAIM AGAINST BUYER. In some jurisdictions, some of the foregoing warranty disclaimers or damage limitations may not apply. BUYER'S TRANSFER OBLIGATIONS:
If the Products/Samples purchased by Buyer are to be resold or delivered to a third party, Buyer must provide such third party with a copy of this document, all specifications, manuals, catalogs, leaflets and written information provided to Buyer pertaining to the Products/Samples. E 1101-3 E BT-W100GA/W155GA-IM Copyright (c) 2016 KEYENCE CORPORATION. All rights reserved. 13982E 1076-1 96M13982 Printed in Japan 6