96M17041 Safety Precautions on LED Product Handheld Terminal DX Series Instruction Manual Be sure to read this instruction manual carefully prior to operating this product. After reading, keep this manual in a safe place so that you can refer to it at any time. The degree of risk of this product is shown below. Risk group 1
* LED product is classified as shown below according to IEC 62471. Exempt group Does not pose any photobiological hazard. Risk Group 1 (Low-Risk) Does not pose a hazard due to normal behavioral limitations on exposure. Risk Group 2 (Moderate-Risk) Does not pose a hazard due to the aversion Risk Group 3 (High-Risk) response to very bright light sources or due to thermal discomfort. May pose a hazard even for momentary or brief exposure. Follow the instructions mentioned in this manual. Otherwise, injury to the human body
(eyes and skin) may result. CAUTION Possibly hazardous optical radiation emitted from this product. Do not stare at operating lamp. May be harmful to the eyes. In this instruction manual, DX Series means the DX-A600/A600GE/A400/A400GE/W600. Symbols Safety Precautions General cautions l a u n a M n o i t c u r t s n I The following symbols alert you to important messages. Be sure to read these messages carefully. DANGER WARNING CAUTION Indicates a hazardous situation which, if not avoided, will result in death or serious injury. Indicates a hazardous situation which, if not avoided, could result in death or serious injury. Indicates a hazardous situation which, if not avoided, could result in minor or moderate injury. NOTICE Indicates a situation which, if not avoided, could result in product damage as well as property damage. Important Indicates cautions and limitations that must be followed during operation. Point Indicates additional information on proper operation. Reference Indicates tips for better understanding or useful information. IEEE 802.11a/b/g/n/ac: These wireless LAN standards are set by the IEEE (Institute of Electrical and Electronics Engineers) 802 LAN/MAN Standards Committee responsible for formulating LAN technology standards. The Bluetooth word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and any use of such marks by KEYENCE is under license. Other trademarks and brand names are the property of their respective owners. microSD, microSDHC, and microSDXC are trademarks of the SD Association. Android is a trademark of Google LLC. Windows is a trademark or registered trademark of Microsoft Corporation in the United States and other countries. Intel is a trademark or registered trademark of Intel Corporation. ARM is a trademark or registered trademark of ARM Limited. FeliCa is a registered trademark of Sony Corporation. Other company names and product names described in this manual are registered trademarks or trademarks of each company. It is prohibited to use or copy all or any part of this manual without prior approval. The information contained in this manual is subject to change without notice. Software information This product incorporates the software files developed independently by or for Keyence Corporation, software files owned and licensed by a third party, and software files subject to certain open source license agreements. For information about such open source software files, please refer to the information displayed on the following screen. DX-A600/A400: From the app list screen, Settings Device information Legal information DX-W600: From the Start menu (All apps), DX setup tool Device information Legal information Such open source software files are provided on an AS IS basis to the maximum extent permitted by applicable law. You may obtain a copy of the source code corresponding to the binaries for GPL/
LGPL-licensed files by sending a request to Keyence customer service at soft-license@keyence.co.jp. There will be a charge to cover the costs of providing the source code. Safety Precautions on Laser Product The DX Series uses a visible semiconductor laser as a light source. Follow the instructions mentioned in this manual. Otherwise, injury to the human body
(eyes and skin) may result. WARNING Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure. Do not disassemble this product. Laser emission from this product is not automatically stopped when it is disassembled. Class 1 Laser Product Do not stare into the direct or specularly reflected beam. Complies with 21 CFR 1040.10 and 1040.11 except for conformance with IEC 60825-1 Ed. 3., as described in Laser Notice No. 56, dated May 8, 2019. The DX Series is classified as below in accordance with IEC 60825-1: 2014. Item Wavelength Output DX-A600/A600GE/A400/A400GE/W600 655 nm 390 W Laser class Class 1 laser product (IEC60825-1, FDA(CDRH) Part 1040.10*)
* The laser classification for FDA (CDRH) is implemented based on IEC 60825-1: 2014 in accordance with the requirements of Laser Notice No. 56. DANGER Do not use this product for the purpose of protecting a human body or a part of a human body. This product is not intended for use as an explosion-proof product. Do not use this product in a hazardous location and/or potentially explosive atmosphere. Do not use this product in an application that may cause death, serious injury, or serious property damage due to a failure with this product occurring, such as nuclear power plants, on aircraft, trains, ships, or vehicles, used within medical equipment, playground equipment, roller coasters and other rides, etc. WARNING If the product is used in a manner not specified by the manufacturer, the protection provided by the product may be impaired. Be sure to check that this product performs properly before starting the work or operation. CAUTION We recommend that you take substantial safety measures to avoid any damage in the event of a problem occurring. Do not use this product in a manner not specified herein. Doing so may result in fire, electric shock, or malfunction. NOTICE Do not modify this product or use it in any way other than described in the specifications. Otherwise, the functions and performance cannot be guaranteed. Microscopic spots (black/bright spots), uneven brightness, or crosstalk (a phenomenon where non-existent lines or patterns are displayed) may occur on the LCD panel depending on the conditions. If the same display remains on the screen for a long time, afterimage may occur due to the characteristics of LCD. WARNING Using batteries other than those specified by KEYENCE may cause fire or explosion. Be sure to use the specified battery. NOTICE Use or store this product within the temperature range described in Specifications (page 3). Do not leave the product inside a closed car or at a place exposed to direct sunlight. Doing so may damage the unit or change its reading performance. Use within the humidity range described in Specifications (page 3). Do not use the product at locations where condensation occurs due to the rapid temperature change. Doing so may damage the unit. This is a precision instrument. Dropping this product or subjecting it to shock may cause damage. Be careful when carrying or using this unit. Do not place the DX Series in a location with high humidity or a dusty area. Doing so may damage the unit. Do not insert a sharp object such as a needle into the buzzer hole on the back side of the DX Series. The tarpaulin may be damaged. Handling of DX Series Handling of main battery (DX-BP6/BP3) and communication unit with built-in main battery (DX-BS6/BS3/BQ6/BQ3) WARNING Observe the following precautions during use. Failure to do so may result in heat generation, smoke generation, fire, explosion, battery leakage, gas leakage, etc. of the main battery pack. Only use the specified battery. Do not charge, use, or store the main battery at locations of high temperature above the specified rangesuch as near fire, in a heated car, and under the scorching sunor at locations of low temperature below the specified range. Do not put it into fire or subject to heat. If there is battery leakage or abnormal smell, immediately take it away from fire. Do not drop the main battery or subject it to strong pressure (such as by crushing, bending, deforming, making holes in, cutting, or throwing it). NOTICE Do not charge when conductive material is affixed to the charging/
communication contact. Clean this contact prior to charging. 1 DX_IM_GB Precautions on Regulations and Standards Precautions on wireless LAN WARNING Important Remove the main battery of the DX Series near locations where using wireless devices is banned at medical institutions or near electric devices for medical purposes. Carry and use the product away from an implanted cardiac pacemaker. Communication may be impossible at locations near metallic objects, locations surrounded with metallic walls, where there is a lot of metallic powder, and in similar usage environments. Be sure to check whether communication is possible prior to installation. If this product is used near devices with the same frequency band, radio wave interference may occur and the communication speed may become slow or communication may become impossible.
[Japan]
Never disassemble or modify this device. Doing so is prohibited by the Radio Act. This device is specified radio equipment according to the Radio Act. Follow the criteria defined within this act to obtain construction design certification. This device may be used outdoors when communicating with registered stations in the 5.2 GHz band. Electromagnetic display of technical standards compliance mark This terminal complies with technical standards based on the Radio Act and Telecommunications Business Act of Japan. The mark indicating this compliance (
can be viewed as indicated below. DX-A600/A400: From the app list screen, Settings About phone Regulatory DX-W600: From the Start menu (All apps), DX setup tool Device information Regulatory
) CE and UKCA Markings KEYENCE Corporation has confirmed, on the basis of the following specifications, that this product complies with the essential requirements of the applicable EU Directive(s) and UK regulations. Be sure to consider the following specifications when using this product in the Member States of the European Union and in the United Kingdom. RE Directive (CE) and Radio Equipment Regulations (UKCA) The full text of the EU declaration of conformity is available at the following internet address: http://www.keyence.com/cedoc Frequency band of operation: Maximum radio-frequency power DX-W600 WLAN Bluetooth NFC:
DX-A600GE WLAN Bluetooth NFC:
WWAN WCDMA LTE DX-A400GE WLAN Bluetooth NFC:
WWAN WCDMA LTE 2400 to 2483.5 MHz: 20 dBm (100 mW) 5200 to 5690 MHz: 23 dBm (199.5 mW) 2400 to 2483.5 MHz: 9 dBm (7.9 mW) 13.56 MHz: 17 dBuA/m 2400 to 2483.5 MHz: 20 dBm (100 mW) 5120 to 5350 MHz: 23 dBm (199.5 mW) 2400 to 2483.5 MHz: 13 dBm (20 mW) 13.56 MHz: -10 dBuA/m Band 1: 20.5 dBm (112.2 mW) Band 8: 24.5 dBm (281.8 mW) Band 1: 20 dBm (100 mW) Band 3: 21 dBm (125.9 mW) Band 7: 20 dBm (100 mW) Band 8: 24 dBm (251.2 mW) Band 38: 24 dBm (251.2 mW) 2400 to 2483.5 MHz: 17 dBm (50.1 mW) 5120 to 5350 MHz: 22 dBm (158.5 mW) 2400 to 2483.5 MHz: 10 dBm (10 mW) 13.56 MHz: -12 dBuA/m Band 1: 22.5 dBm (177.8 mW) Band 8: 24 dBm (251.2 mW) Band 1: 22.5dBm (177.8 mW) Band 3: 24 dBm (251.2 mW) Band 7: 18.5 dBm (70.8 mW) Band 8: 24 dBm (251.2 mW) Band 38: 20.5 dBm (112.2 mW) Remarks: These specifications do not give any guarantee that the end-product with this product incorporated complies with the essential requirements of RE Directive and Radio Equipment Regulations. The manufacturer of the end-product is solely responsible for the compliance on the end-product itself according to this directive and these UK regulations. The device is restricted to indoor use only when operating in the 5150 to 5350 MHz frequency range. AT EE IT PT IS BE FI LV RO LI BG FR LT SK NO HR DE LU SI CH CY EL MT ES TR CZ HU NL SE DK IE PL UK(NI) UL certification The DX Series complies with the following UL/CSA standards and has obtaied the UL/
C-UL certifications. UL File No. UL category Applicable standards UL 62368-1 E167973 AZOT/AZOT7 CAN/CSA-C22.2 No. 62368-1 This product is intended to be supplied by an UL Listed power supply and power cord suitable for use at 55C min., the power supply output is rated: 5 Vdc, 2 A with marked Class II, L.P.S. or PS2, if need further assistance, please contact KEYENCE CORPORATION for further information. DX_IM_GB 2 Ce produit est destin tre aliment par une alimentation et un cordon d'alimentation homologus UL adapts une utilisation 55C min., la sortie d'alimentation est nominale : 5 Vdc, 2 A avec marqu Class II, L.P.S. ou PS2, si vous avez besoin d'aide supplmentaire, veuillez contacter KEYENCE CORPORATION pour plus d'informations. Be sure to consider the following specifications when using this product as a UL certified product. Use this product in combination with the DX-BS*/BQ*/BP*/KE1, which has obtained UL certification. CAUTION RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE. DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS. FCC Regulations This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions; (1) This device may not cause harmful interface, and (2) this device must accept any interference received, including interference that may cause undesired operation. Application regulation FCC Part 15 Subpart B Class A FCC Part 15 Subpart C FCC Part 15 Subpart E 5150-5350MHz band is restricted to indoor operations only. Regulatory information page is located at:
DX-A600/A400: From the app list screen, Settings About phone Regulatory DX-W600: From the Start menu (All apps), DX setup tool Device information Regulatory This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his/her own expense. CAUTION Changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. The product comply with the US portable RF exposure limit set forth for an uncontrolled environment and are safe for intended operation as described in this manual. The further RF exposure reduction can be achieved if the product can be kept as far as possible from the user body or set the device to lower output power if such function is available. This transmitter must not be co-located or operated in conjunction with any other antenna or transmitter. This equipment should be installed and operated at least 10 mm away from your body. ISED Regulations This device complies with the following regulations specified by the ISED. Applicable regulation CAN ICES-003 (A) / NMB-003 (A) RSS-247 RSS-102 The device for operation in the band 51505250 MHz is only for indoor use to reduce the potential for harmful interference to co-channel mobile satellite systems. Operations in the 5250-5350 MHz band are restricted to indoor usage only. 5600-5650 MHz band is not allowed at Canada. Les dispositifs fonctionnant dans la bande de 5150- 5250MHz sont rservs uniquement pour une utilisation lintrieur afin de rduire les risques de brouillage prjudiciable aux systmes de satellites mobiles utilisant les mmes canaux. Les oprations dans la bande de 5250-5350 MHz sont limits un usage intrieur seulement. La bande de 5600-5650 MHz n'est pas autorise au Canada. CAUTION This device complies with Industry Canadas licence-exempt RSSs. Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. The product comply with the Canada portable RF exposure limit set forth for an uncontrolled environment and are safe for intended operation as described in this manual. The further RF exposure reduction can be achieved if the product can be kept as far as possible from the user body or set the device to lower output power if such function is available. This equipment should be installed and operated at least 10 mm away from your body. Le prsent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorise aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible d'en compromettre le fonctionnement. Le produit est conforme aux limites d'exposition pour les appareils portables RF pour les Etats-Unis et le Canada tablies pour un environnement non contrl. Le produit est sr pour un fonctionnement tel que dcrit dans ce manuel. La rduction aux expositions RF peut tre augmente si l'appareil peut tre conserv aussi loin que possible du corps de l'utilisateur ou que le dispositif est rgl sur la puissance de sortie la plus faible si une telle fonction est disponible. Cet quipement doit tre install et utilis une distance d'au moins 10 mm de votre corps. Precautions for Proper Use Handling of packing NOTICE If units such as the DX-BS6 are not properly attached, the enclosure rating of the DX Series cannot be guaranteed. When using this product in environments where water or dust is present, check if these units are properly attached. Dropping the DX Series or subjecting it to extreme shock may lead to the loss of water-proofing. Take adequate care when handling this product. Cleaning Clean the following parts with compressed air periodically. If removing dirt is difficult, use a dry cotton swab to clean the unit connectors and charging/
communication contact.
(Use absolute ethanol if dirt is stuck on them.) When using an expansion unit, also clean its charging/communication contact. Unit connectors Charging/communication contact during contact charging
(DX-BS6 in this figure) Unit Installation As an example, the installation of the DX-BS6 is explained below. 1 Insert the tip of the unit into the back of the main unit. microSD / nano SIM card installation The DX-A600/A400 has a microSD slot and a nano SIM slot. The DX-W600 has a microSD slot. 1 Turn off the main unit and remove the main battery. DX-A600/A400 nano SIM card DX-W600 microSD card 2 Attach the unit to the main unit by using two fingers to push the two parts of the unit indicated with arrows until they click.
* To remove the unit, press the tabs on the back of the main unit from the left and right, and then pull the unit up from the main unit. 2 3 4 5 2 Slide the desired slot cover in the direction of the arrow to unlock it, allowing the card to be inserted. 3 Open the slot cover. 4 For the DX-A600/
A400, orient the card with its terminals at the bottom, and then place it in the slot. For the DX-W600, insert the card into the slot cover so the terminals are at the bottom when the slot cover is closed, as shown in the figure. 5 Close the slot cover and lock it by sliding it in the direction of the arrow. NOTICE Even when not using a microSD or nano SIM card, be sure to close and lock the slot cover(s). The slot cover(s) may be damaged if unlocked. NOTICE If dirt or dust is attached, contact failure may occur on the unit connectors or charging/communication contact. This may cause charging function deterioration and instantaneous interruption. Make sure that textile waste is not attached to the unit connectors or charging/communication contact when cleaning. Checking the Package When opening the package, check that the following items are all included. In the event of missing, defective, or damaged items, contact your nearest KEYENCE sales office. DX-A600/A600GE/A400/A400GE/W600 Main unit...1 Instruction Manual...1 Specifications Controller CPU OS Main memory Internal memory Display Operation confirmation LED Operations Hard keys Model DX-A600/A600GE DX-A400/A400GE ARM Penta Core Android 3 GB RAM, 16 GB ROM DX-W600 Intel Quad Core + Scan processor Windows 10 IoT Enterprise 4 GB RAM, 64 GB ROM LCD 6.0-inch, 720 1440 4.0-inch, 480 800 6.0-inch, 720 1440 3-color LED Trigger keys 2, volume up and down keys, power key, side Fn keys 2 Trigger keys 2, volume up and down keys, power key, front Fn keys 3 Trigger keys 2, volume up and down keys, power key, side Fn keys 2 Touch panel Electrostatic capacitance method (reinforced glass specifications) Scanner Reading light source Pointer light source Minimum resolution Field range Supported codes Wireless LAN High-intensity white LED Visible light semiconductor laser (655 nm) Output 390 W Class 1 laser product (IEC 60825-1) 2D code: 0.169 mm, barcode: 0.076 mm 186 114 mm (reading distance: 200 mm) UPC/EAN/JAN (add-on code supported), CODE128, GS1-128, CODE39, Codabar (NW-7), CODE93, ITF, COOP2of5, industrial 2of5, QR code, micro QR, DataMatrix (ECC200), PDF417, GS1 DataBar, composite symbol, Postal IEEE802.11 a/b/g/n/ac 2.4 GHz (b,g,n: 1 to 11 ch) 5.2 GHz, 5.3 GHz (a/n/ac)
*1 IEEE802.11 a/b/g/n/ac 2.4 GHz
(b,g,n: 1 to 14 ch) 5.2 GHz, 5.3 GHz, 5.6 GHz, 5.8 GHz
(a/n/ac)*1*2 Bluetooth V4.2 BR/EDR/LE Communication Bluetooth Bluetooth V5.1 BR/EDR/LE WWAN GNSS NFC External media 4G LTE / 3G, SIM-free, 1 nano SIM slot GPS, A-GPS, GLONASS, Beidou
ISO14443 Type A, B, FeliCa, ISO15693 micro SD/SDHC/SDXC UHS-I Main battery Dedicated lithium ion battery pack Clock Built-in lithium ion secondary battery, time: approx. 1 month*3 DX_IM_GB Power supply 3 DX-BS6 27.2 66.1 DX-BS3 17.3 66.1 DX-BS3H 22.5 66.1 3
. 2 2 1 6
. 7 1 1 DX-BC6 22.4 40.6 DX-BQ6 22 66.1 DX-BQ3 15.5 66.1 7
. 8 7 6
. 7 1 1 6
. 7 1 1 6
. 7 1 1 WARRANTIES AND DISCLAIMERS
(1) KEYENCE warrants the Products to be free of defects in materials and workmanship for a period of one (1) year from the date of shipment. If any models or samples were shown to Buyer, such models or samples were used merely to illustrate the general type and quality of the Products and not to represent that the Products would necessarily conform to said models or samples. Any Products found to be defective must be shipped to KEYENCE with all shipping costs paid by Buyer or offered to KEYENCE for inspection and examination. Upon examination by KEYENCE, KEYENCE, at its sole option, will refund the purchase price of, or repair or replace at no charge any Products found to be defective. This warranty does not apply to any defects resulting from any action of Buyer, including but not limited to improper installation, improper interfacing, improper repair, unauthorized modification, misapplication and mishandling, such as exposure to excessive current, heat, coldness, moisture, vibration or outdoors air. Components which wear are not warranted.
(2) KEYENCE is pleased to offer suggestions on the use of its various Products. They are only suggestions, and it is Buyer's responsibility to ascertain the fitness of the Products for Buyers intended use. KEYENCE will not be responsible for any damages that may result from the use of the Products.
(3) The Products and any samples ("Products/Samples") supplied to Buyer are not to be used internally in humans, for human transportation, as safety devices or fail-safe systems, unless their written specifications state otherwise. Should any Products/Samples be used in such a manner or misused in any way, KEYENCE assumes no responsibility, and additionally Buyer will indemnify KEYENCE and hold KEYENCE harmless from any liability or damage whatsoever arising out of any misuse of the Products/Samples.
(4) OTHER THAN AS STATED HEREIN, THE PRODUCTS/SAMPLES ARE PROVIDED WITH NO OTHER WARRANTIES WHATSOEVER. ALL EXPRESS, IMPLIED, AND STATUTORY WARRANTIES, INCLUDING, WITHOUT LIMITATION, THE WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, AND NON-INFRINGEMENT OF PROPRIETARY RIGHTS, ARE EXPRESSLY DISCLAIMED. IN NO EVENT SHALL KEYENCE AND ITS AFFILIATED ENTITIES BE LIABLE TO ANY PERSON OR ENTITY FOR ANY DIRECT, INDIRECT, INCIDENTAL, PUNITIVE, SPECIAL OR CONSEQUENTIAL DAMAGES (INCLUDING, WITHOUT LIMITATION, ANY DAMAGES RESULTING FROM LOSS OF USE, BUSINESS INTERRUPTION, LOSS OF INFORMATION, LOSS OR INACCURACY OF DATA, LOSS OF PROFITS, LOSS OF SAVINGS, THE COST OF PROCUREMENT OF SUBSTITUTED GOODS, SERVICES OR TECHNOLOGIES, OR FOR ANY MATTER ARISING OUT OF OR IN CONNECTION WITH THE USE OR INABILITY TO USE THE PRODUCTS, EVEN IF KEYENCE OR ONE OF ITS AFFILIATED ENTITIES WAS ADVISED OF A POSSIBLE THIRD PARTYS CLAIM FOR DAMAGES OR ANY OTHER CLAIM AGAINST BUYER. In some jurisdictions, some of the foregoing warranty disclaimers or damage limitations may not apply. BUYER'S TRANSFER OBLIGATIONS:
If the Products/Samples purchased by Buyer are to be resold or delivered to a third party, Buyer must provide such third party with a copy of this document, all specifications, manuals, catalogs, leaflets and written information provided to Buyer pertaining to the Products/Samples. E 1101-3 Accelerometer, gyroscope, ambient light, proximity, temperature and humidity, air pressure 5C to +50C, When charging 0C to
+40C*4 Microphone 2, noise canceling 1 Speaker Vibrator 1 speaker, 1 receiver Built in Color camera Rear camera: 8MP-AF, front camera: 5MP Others Sensor Accelerometer, gyroscope, digital compass, ambient light, proximity, temperature and humidity, air pressure Environmental resistance Operating ambient temperature Operating ambient humidity Storage ambient temperature Storage relative humidity 20C to +50C, When charging 0C to +40C*4 20% to 85% RH (no condensation) 20C to +60C (no freezing) 20% to 85% RH (no condensation) Dimensions 175.5 85.9 31.5 mm 143.5 73.7 31.8 mm 175.5 85.9 31.5 mm Weight Approx. 220 g Approx. 165 g Approx. 230 g
*1 Outdoor use of 5.2/5.3 GHz band wireless LAN is prohibited. This does not include communication with access points / relay stations of 5.2 GHz band high-output data communication systems.
*2 The usable frequency band varies depending on the region.
*3 When the main battery is not attached or has no remaining charge.
*4 Due to the added load in sub-zero environments, the continuous usage time may be reduced significantly. Be sure to test the device before use in these environments. Model DX-BS6 DX-BS3*2 DX-BS3H*2 DX-BC6*1 DX-BQ6 DX-BQ3*2 Display 2-color LED 2-color LED Capacity 6060 mAh 3030 mAh 6270 mAh 6060 mAh 3030 mAh Dedicated lithium ion battery pack Charging confirmation LED Type Power supply Charging time Approx. 7 hours Approx. 4 hours Magnetic connector Supported (charging/
communication)
* Connected to DX-UC4, DX-UC4E, DX-UC1UL, DX-UC1M, or OP-88604
(magnetic charging cable) Interface USB Non-
contact charging
Approx. 7.5 hours
(non-conta ct charging), approx. 6 hours
(USB) Approx. 5 hours
(non-conta ct charging), approx. 4 hours
(USB)
Supported (charging/
communication)
* Connected to USB micro B, USB 2.0 OTG, or OP-88603 (USB micro B cable)*3 Built in (charging)
* Charger compliant with Qi 1.1 standard Dimensions Weight Accessories 122.3 x 66.1 x 27.2 mm Approx. 155 g 117.6 x 66.1 x 17.3 mm 117.6 x 66.1 x 22.5 mm Approx. 100 g 78.7 x 40.6 x 22.4 mm Approx. 115 g 117.6 x 66.1 x 22 mm Approx. 155 g 117.6 x 66.1 x 15.5 mm Approx. 105 g Hand strap back cover
Hand strap back cover
*1
*2
*3 The DX-BC6 can only be used when an expansion unit is installed. The DX-BC6 interface and charging confirmation LED are on this unit. It is not recommended to use the DX-W600 with the DX-BS3/BQ3. OTG conversion cable required with USB Host mode specifications. Outline Dimensional Drawings DX-A600/A600GE/W600 DX-A400/A400GE 31.5 85.9 84.9 31.8 73.7 72.7 5
. 5 7 1 5
. 3 4 1 DX_IM_GB Unit: mm
* With DX-BS3 installed Copyright (c) 2022 KEYENCE CORPORATION. All rights reserved. 17041GB 2022-1 96M17041 Printed in Japan 4