Fact Sheet KINEXON RECEIVER User Manual Indoor Application Version 1.2 Battery and/or cable (5-30 V), PoE (48V) ABS 126 x 98 x 34 mm 200 g / 505 g (with battery) RECEIVER (Kinexon Receiver):
Material:
Dimensions:
Weight:
Power Supply:
Battery Lifetime:
Charging:
Temperature:
Communication:
SETUP Receiver Mounting The Kinexon Receiver will only be placed indoors, where it will be usually mounted on walls or on tripods. Kinexon offers dedicated mounting mechanisms. Alternatively, the Receivers can be mounted on tripods in case that mounting on walls is not possible. 35 hours (active), 200 days (standby) 10 hours (100%), 5 hours (50%), 12-24 V DC
-40 75 C 2.4/5 GHz (Wifi), 3.23738-6.81013 GHz (UWB), 100Base-TX Ethernet receiver Regulatory and Legal Information The Kinexon Receiver has been designed to be in compliance with both the U.S. FCC Part 15 subpart F regulations, sections 15.517 and 15.521 and with the European Union ETSI EN 302 065 standards. Two different versions of the Kinexon Receiver are available, one version supports the FCC emissions mask (Region 1) and the second supports the ETSI standard mask (Region 2). Kinexon 2015. This document is confidential and contains information which is proprietary to Kinexon GmbH. No reproduction is permitted without prior express written permission of the author (info@kinexon.com).
- CONFIDENTIAL -
2 Disclaimer The information in this document is subject to change without notice. Kinexon GmbH assumes no responsibility for inaccuracies or omissions and specifically disclaims any liabilities, losses, or risks, personal or otherwise, incurred as a consequence, directly or indirectly, of the use or application of any of the contents of this document. For the latest documentation, contact Kinexon GmbH. Intended Use This manual describes the setup and use of the Kinexon Receiver. Use this product only for the purpose it was designed for. FCC Compliance This device complies with 47 CFR Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. The user is cautioned that changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. This device may not be employed for the operation of toys. Operation onboard an aircraft, a ship or a satellite is prohibited. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Increase the separation between the equipment and receiver. Reorient or relocate the receiving antenna. Connect the equipment to an outlet on a circuit different from that to which Consult the dealer or an experienced radio/TV technician for help. the receiver is connected. Kinexon 2015. This document is confidential and contains information which is proprietary to Kinexon GmbH. No reproduction is permitted without prior express written permission of the author (info@kinexon.com).
- CONFIDENTIAL -
3 Important Notice This equipment may only be operated indoors. Operation outdoors is in violation of 47 U.S.C. 301 and could subject the operator to serious legal penalties. The Kinexon Receiver will only operate (i.e. transmit UWB signals) when activated within an indoor Kinexon network. This network needs to be professionally installed, and must be configured to cover only the volume indoors, preventing the Kinexon Receiver from emitting UWB signals outdoors. Contact Kinexon GmbH if you are unsure about the extent of coverage of your network system. Safety Information Read and follow all instructions before using the Kinexon Receiver. Never open the case of the Kinexon Receiver. There are no user serviceable parts or replaceable parts inside the case. Do not use the Kinexon Receiver if it has been damaged. Kinexon 2015. This document is confidential and contains information which is proprietary to Kinexon GmbH. No reproduction is permitted without prior express written permission of the author (info@kinexon.com).
- CONFIDENTIAL -
4