FCC ID: RGB-P250061D P250061

 

®

93133624_A

P250061

Limited Lifetime Warranty

Progress Lighting fan motors are warranted to the original purchaser to be free of electrical and/or mechanical

defects for so long as the original purchaser owns the fan. Pull chain switches, reverse switches, capacitors and

metal finishes are warranted to be free from defects in materials or workmanship for a period of 1 year from

the date of purchase. Warping of wooden or plastic blades is not covered by this warranty nor is corrosion and/

or deterioration of any finishes for fans installed within ten miles of any sea coast. Extended warranties for

ENERGY STAR® qualified products may apply.

Progress Lighting ceiling fans with built-in LED light sources, when properly installed and under normal

conditions of use, are warranted to be free from defects in material and workmanship which cause the light

sources to fail to operate in accordance with the specifications for (i) five (5) years from the date of purchase

on the LED Light modules and electrical components for fans used in single family residences, and (ii) three

(3) years from the date of purchase on the LED Light modules and electrical components for fans used in

multi-family or commercial applications. LED bulbs supplied by Progress Lighting carry no warranty other

than manufacturer’s warranty. Non-LED bulbs carry no warranty.

With proof of purchase, the original purchaser may return the defective fan to the place of purchase during the

first 30 days for replacement. After 30 days, the original purchaser MUST contact Progress Lighting at (864)

678-1000 for repair or replacement which shall be determined in Progress Lighting’s sole discretion and shall

be purchaser’s sole and exclusive remedy.

Date Purchased

Store Purchased

UL Model No.

P250061

Serial No.

Vendor No.

111017

Labor and Shipping Excluded. This warranty does not cover any costs or fees associated with the labor

(including, but not limited to, electrician’s fees) required to install, remove, or replace a fan or any fan parts.

UPC

This warranty shall not apply to any loss or damage resulting from (i) normal wear and tear or alteration,

misuse, abuse or neglect, or (ii) improper installation, operation, repair or maintenance by original purchaser

or a third party, including without limitation improper voltage supply or power surge, use of improper parts or

accessories, unauthorized repair (made or attempted) or failure to provide maintenance to the fan.

THE FOREGOING WARRANTIES STATE PROGRESS LIGHTING’S ENTIRE WARRANTY OBLIGATION

AND ORIGINAL PURCHASER’S SOLE AND EXCLUSIVE REMEDY RELATED TO SUCH PRODUCTS.

PROGRESS LIGHTING IS NOT RESPONSIBLE FOR DAMAGES (INCLUDING INDIRECT, SPECIAL,

INCIDENTIAL OR CONSEQUENTIAL), DUE TO PRODUCT FAILURE, WHETHER ARISING OUT OF

BREACH OF WARRANTY, BREACH OF CONTRACT, OR OTHERWISE. THIS WARRANTY IS GIVEN

IN LIEU OF ALL OTHER WARRANTIES, WHETHER EXPRESSED OR IMPLIED, INCLUDING THOSE

OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE OR NONINFRINGEMENT.

Some states do not allow limitations on how long an implied warranty lasts or the exclusion or limitations

of incidental or consequential damages, so the above limitations and exclusions may not apply to you. This

warranty gives you specific rights and you may have other rights which vary from state to state.

Making the Electrical Connections

Safety Rules

Unpacking Your Fan

Installing Your Fan

Remote Control

Operating Your Fan

Care of Your Fan

Troubleshooting

Specifications

1

2

3

6

10

11

12

12

13

Table of Contents

READ AND SAVE THESE INSTRUCTIONS

1. To reduce the risk of electric shock, insure electricity has been

turned off at the circuit breaker or fuse box before beginning.

2. All wiring must be in accordance with the National Electrical

Code ANSI/NFPA 70-1999 and local electrical codes.

Electrical installation should be performed by a qualified

licensed electrician.

3. CAUTION: To reduce the risk of personal injury, use only the

screws provided with the electrical box.

4. The outlet box and support structure must be securely

mounted and capable of reliably supporting 35 lbs. (15.9 kg).

Use only cUL Listed outlet boxes marked “Acceptable for Fan

Support of 35 lbs. (15.9 kg) or less.”

5. CAUTION: The fan must be mounted with a minimum of 7

feet clearance from the trailing edge of the blades to the floor.

6. Do not wait for the fan to stop before pressing the reverse

button. The fan will not reverse direction if the fan is not

moving.

7. Avoid placing objects in path of the blades.

TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK OR PERSONAL

INJURY, MOUNT TO OUTLET BOX MARKED “ACCEPTABLE FOR FAN

SUPPORT OF 35LBS. (15.9 KG) OR LESS”, AND USE SCREWS PRO-

VIDED WITH THE OUTLET BOX.

TO REDUCE THE RISK OF PERSONAL INJURY, DO NOT BEND THE

BLADE BRACKETS (ALSO REFERRED TO AS (“FLANGES”) DURING

ASSEMBLY OR AFTER INSTALLATION. DO NOT INSERT OBJECTS IN

THE PATH OF THE BLADES.

1. Safety Rules

8. To avoid personal injury or damage to the fan and other items,

be cautious when working around or cleaning the fan.

9. Do not use water or detergents when cleaning the fan or fan

blades. A dry dust cloth or lightly dampened cloth will be

suitable for most cleaning.

10. After making electrical connections, spliced conductors should

be turned upward and pushed carefully up into electrical box.

The wires should be spread apart with the grounded conductor

and the equipment-grounding conductor on one side of the

electrical box and ungrounded conductor on the other side of

the electrical box.

11. Electrical diagrams are for reference only. Light kits that

are not packed with the fan must be cUL Listed and marked

suitable for use with the model fan you are installing. Switches

must be cUL General Use Switches. Refer to the instructions

packaged with the light kits and switches for proper assembly.

12. All set screws must be checked and retightened where

necessary before installation.

13. WARNING: To reduce the risk of fire or electric shock,

this fan should only be used with fan speed control part

no. DP-52R, manufactured by DAWNSUN ELECTRONIC

TECHNOLOGY CO LTD ZHONGSHAN.

TO REDUCE THE RISK OF SHOCK, THIS FAN MUST BE INSTALLED

WITH AN ISOLATION WALL CONTROL/SWITCH.

1

2

3

4

5

6

7

8

9

10

(cid:21)(cid:75)

(cid:23)(cid:75)

(cid:27)(cid:75)

(cid:21)

(cid:22) (cid:23)

(cid:50)(cid:41)(cid:41)

(cid:20) (cid:25)

(cid:24)

R

11

12

a

b

c

Unpack your fan and check the contents. You should have the following items:

1. Mounting Bracket

2. 6” Ball/Downrod Assembly (hanger pin

and locking pin pre-attached)

3. Canopy with Canopy Ring (attached)

4. Decorative Motor Collar Cover

5. Fan Motor Assembly

6. Blade brackets (5)

7. Blades (5)

8. Light Kit Pan

9. Light Kit Fitter Assembly

10. Light Shade

11. Transmitter and Receiver

12. Extension Lead Wire

a. Blade attachment hardware

(16 screws for attaching blades to blade arms)

b. Electrical hardware and balancing kit

(1 plastic wire connectors, blade balancing kit)

c. Blade bracket attachment hardware

(1 extra screw for attaching blade arms to the

fan motor assembly)

2. Unpacking Your Fan

Tools Required

Figures 1, 2, and 3 are examples of different

ways to mount the electrical box.

Phillips screw driver or straight slotted screw

driver, adjustable wrench, step ladder, and

wire cutters.

Mounting Options

If there isn’t an existing electrical box, then

read the following instructions. Disconnect

the power by removing fuses or turning off

circuit breakers.

Secure the electrical box directly to the building

structure. Use appropriate fasteners and

building materials. The electrical box and

its support must be able to fully support the

moving weight of the fan (at least 35 lbs.).

Do not use plastic electrical boxes.

TO REDUCE THE RISK OF FIRE, ELECTRIC

SHOCK OR PERSONAL INJURY, MOUNT TO

OUTLET BOX MARKED “ACCEPTABLE FOR

FAN SUPPORT OF 35 LBS. (15.9 KG) OR

LESS”, AND USE SCREWS PROVIDED WITH

THE OUTLET BOX. ELECTRICAL BOXES

COMMONLY USED FOR THE SUPPORT OF

LIGHTING FIXTURES MAY NOT BE ACCEPTABLE

FOR FAN SUPPORT AND MAY NEED TO

BE REPLACED. CONSULT A QUALIFIED

ELECTRICIAN IF IN DOUBT.

3. Installing Your Fan

Figure 3

Note: You may need a longer downrod to

maintain proper blade clearance when installing

on a steep, sloped ceiling. The maximum

angle allowable is 20˚. If the canopy touches

downrod, remove the decorative canopy

bottom cover and turn the canopy 180˚ before

attaching the canopy to the mounting plate.

Figure 1

Figure 2

To hang your fan where there is an existing

fixture but no ceiling joist, you may need an

installation hanger bar as shown in Figure 4.

Figure 4

Hanging the Fan

REMEMBER to turn off the power. Follow

the steps below to hang your fan properly.

NOTE: This fan is recommended for

standard ceiling mount using the downrod

provided with this fan. When using standard

ceiling installation with the 6 inch downrod

provided, the distance from the ceiling

to the bottom of the fan blades will be

approximately 13.7 inches.

Standard Ceiling Mounting

1. Remove the canopy ring from the canopy

by turning the ring to the right until it

unlocks. (Figure 5)

2. Remove the mounting bracket from the

canopy by loosening the four screws on

the top of the canopy. Remove the two

non-slotted screws and loosen the slotted

screws. This will enable you to remove

the mounting bracket. (Figure 6)

3. Remove the hanger pin and locking pin

from downrod assembly.

4. Place downrod over canopy and canopy

ring, slide the motor collar cover onto the

downrod. Route the wires through the ball/

downrod assembly. (Figure 7)

5. Loosen, but do not remove, the set screws

on the collar on the top of the motor

housing.

Turn Canopy Ring to Remove

8. Make sure the grommet is properly installed

in the collar cover, then slide the collar cover

on the downrod until it rests on the motor

housing. Be sure that the canopy and the

collar cover are both oriented correctly.

9. Proceed to “Installing the Fan” section.

Figure 5

Loosen but Do Not Remove

Remove

FAILURE TO PROPERLY INSTALL SET SCREWS

AS NOTED IN STEP 7 COULD RESULT IN FAN

LOOSENING AND POSSIBLY FALLING.

Motor wires

Ball/Downrod

assembly

Canopy

Figure 6

Canopy ring

Motor collar

cover

Hanger pin

Motor collar

Pin in locked position

Locking pin

Tighten screws

6. Align the holes at the bottom of the

downrod with the holes in the collar on top

of the motor housing. (Figure 7)

Carefully insert the hanger pin through the

holes in the collar and downrod. Be careful

not to jam the hanger pin against the wiring

inside the downrod. Insert the locking pin

through the hole near the end of the bolt

until it snaps into its locked position, as

noted in the circle inset of Figure 7.

7. Re-tighten the set screws on the collar on top

of the motor housing.

Figure 7

4.

Installing Fan to

the Electrical Box

WHEN USING THE STANDARD BALL/DOWNROD

MOUNTING, THE TAB IN THE RING AT THE

BOTTOM OF THE MOUNTING BRACKET MUST

REST IN THE GROOVE OF THE HANGER BALL.

FAILURE TO PROPERLY SEAT THE TAB IN THE

GROOVE COULD CAUSE DAMAGE TO WIRING.

1. Pass the 120-volt supply wires through the

center hole in the ceiling mounting bracket

as shown in Figure 8.

2. Install the ceiling mounting bracket on the

electrical box by using the mounting screws

provided with the electrical box. Note that

the flat side of the mounting bracket is

toward the electrical box. (Figure 8)

3. Tighten the two screws on the electrical box

securely.

4. Carefully lift the fan assembly up to the

ceiling mounting bracket. Make sure the tab

on the mounting bracket is properly seated

in the groove in the hanger ball. (Figure 9)

Connecting the Safety

Cable

1. Turn the wood screw (LL)(not provided)

into the ceiling.

2. Place the looped end of the safety cable (S)

onto the wood screw and then tighten the

screw firmly, or connect the safety cable

directly to the electrical box. (Figure 10)

Standard mounting

Figure 8

LL

S

Figure 10

5.

Figure 9

Installing the

Receiver into the

Mounting Bracket

1. Position the house supply wires to one side

of the slide-on mounting bracket; position

the fan wires to the opposite side.

2. Insert the narrow end of the receiver (as

shown, flat side toward ceiling) into the

slide-on mounting bracket until it rests on

top of the ball/downrod assembly. (Figure

11)

Wiring the Receiver to

the Household Wiring

1. Connect the green wire to the household

ground wires using a wire connecting nut.

2. Connect the receiver black wire to

the household black wire using a wire

connecting nut.

3. Connect the receiver white wire to

the household white wire using a wire

connecting nut.

Wiring the Fan to the

Receiver

1. If using the 6 in. ball downrod assembly

provided, wire the receiver to the fan wires

by connecting the molded adaptor plugs

from the receiver with the molded adaptor

plugs of the fan motor assembly together.

(Figure 12)

2. If you wish to use longer downrod, you

can use the extension lead wire (68 in.)

provided by connecting the molded

adaptors together.

SUPPLY CIRCUIT

BLACK

WHITE

L N

Remote

Receiver

GREY

BROWN

ORANGE

GREY

BROWN

ORANGE

GREEN

BLUE

YELLOW

WHITE

BLUE

YELLOW

WHITE

BLUE

BLACK

WHITE

WHITE

Figure 11

6. Making the Electrical Connections

Figure 12

Finishing the Fan

Installation

STANDARD CEILING MOUNTING

WHEN USING THE STANDARD BALL/DOWNROD

MOUNTING, THE TAB IN THE RING AT THE

BOTTOM OF THE MOUNTING PLATE MUST

REST IN THE GROOVE OF THE HANGER BALL.

FAILURE TO PROPERLY SEAT THE TAB IN THE

GROOVE COULD CAUSE DAMAGE TO WIRING.

1. Align the locking slots of the ceiling

canopy with the two screws in the

mounting plate. Push up to engage the

slots and turn clockwise to lock in place.

Immediately tighten the two mounting

screws firmly.

2. Install the remaining two mounting screws

into the holes in the canopy and tighten

firmly.

3. Install the decorative canopy ring by

aligning the ring’s slots with the screws

in the canopy. Rotate the ring counter-

clockwise to lock in place.

4. You may now proceed to attaching the

fan blades.

7.

Blade

Screws

Figure 14

Attaching the Fan

Blades

Note: Your fan blades are reversible. Select the

blade finish which best accentuates your decor.

1. Attach blade to blade bracket using the

screws as shown in figure 15. Start a

screw into the bracket. Repeat for the two

remaining screws.

2. Tighten each screw securely.

3. Fasten the blade assembly to the motor by

inserting the alignment post into the slot on

the bottom of the motor and tightening the

motor screws. Please note that the motor

screws are pre-attached into the blade

brackets (Figure 16).

4. Repeat steps 1, 2 and 3 for the remaining

blades.

Blade arm

Figure 15

Motor Assembly

Screws

Figure 16

Touching

Ceiling

Figure 17

Blade Balancing

All blades are grouped by weight. Because

materials vary in density, the fan may wobble

even though the blades are weight matched.

The following procedure should correct most

fan wobble. Check after each step.

1. Check that all blade screws are secure.

2. Most fan wobble problems are caused

when blade levels are unequal. Check this

level by selecting a point on the ceiling

above the tip of one of the blades. Measure

from a point on the center of each blade

to the point on the ceiling. Measure this

distance as shown in Figure 17. Rotate

the fan until the next blade is positioned

for measurement. Repeat for each blade.

Measurements deviation should be within

1/8”. Run the fan for 10 minutes.

3. Make sure that canopy is tightened securely

to ceiling mounting bracket and that the

ceiling mounting bracket is tightened

securely to the electrical box.

4. Interchanging two adjacent blades can

redistribute the weight and possibly result

in the smoother operation.

5. Use the enclosed Blade Balancing Kit if the

blade wobble is still noticeable.

8.

Installing the Light Kit

Pan/Light Kit Fitter

Assembly/ Light Shade

CAUTION - To reduce the risk of electrical

shock, disconnect the electrical supply circuit

to the fan before installing the light kit.

1. Loosen but do not remove two of three

mounting screws from the fan motor

assembly; Remove one mounting screw.

(Figure 18)

2. Push the light kit pan up to the fan motor

assembly so that the two loosened screw

heads fit into the keyhole slots. Turn the

light kit pan clockwise, and tighten the

screws. Re-install the screw that was

removed in step 1 and tighten firmly.

(Figure 18)

3. Remove one screw from the light kit pan,

and loosen but do not remove the other two

screws. Connect the wires from the light

kit fitter assembly to the wires from the fan

motor assembly by connecting the molded

adaptor plugs together. Carefully tuck

all wires and splices into the switch cap.

(Figure 19)

9.

4. Push the light kit fitter assembly up so

that the two loosened screw heads fit into

the keyhole slots. Turn the light kit fitter

assembly clockwise, tighten the screws. Re-

install the screw that was removed in step 3

and tighten firmly. (Figure 19)

5. Place the light shade into the light kit pan,

aligning the three flat areas on the top of the

light shade with the three raised dimples

in the light kit pan. Turn the light shade

clockwise until it stops. (Figure 20)

PERIODICALLY CHECK THE GLASS SHADE IS

SEATED FULLY CLOCKWISE IN THE LIGHT KIT

PAN ASSEMBLY.

Motor

Assembly

Screws

Light Kit

Pan

Figure 18

Blue

Blac k

White

Light Kit

Pan

Light Kit

Fitter Assembly

Screws

Figure 19

Light Kit

Pan

Light Shade

Figure 20

Mounting the remote

control holder

NOTE: Screw wall anchors are included

for extra support. The included screws are

designed to screw easily into the wall. If you

would like a more permanent or secure hold,

install the wall anchors prior to attaching the

wall cradle to the wall.

1. Position the wall cradle in the desired

position and attach it to the wall using the

included wall cradle screws. (Figure 22)

0

L

F

C

1

D

LEARN

0

L

F

C

1

D

LEARN

Figure 21

Preparing the Remote

Control

NOTE: The remote control has already been

paired to the ceiling fan for your convenience.

If you have two of the same model fans in

your home, please follow the steps below to

control each fan independently.

1. Remove the battery cover by pressing

firmly on the arrow and sliding the cover

off.

2. Install two 1.5V AAA batteries (included).

3. Slide the dip switch in the battery

compartment to the “1” setting.

4. Confirm that the power to the fan is off at

either the wall switch or breaker box.

5. Return power to the fan at the wall switch

or breaker box.

6. Press and release the “Learn” button

located in the remote’s battery

compartment within 30 seconds of turning

on the power.

7. If pairing is successful, the fan’s light kit

will flash and the blades will begin to spin.

8. Replace the battery cover on the remote

control.

Figure 22

10. Remote Control

Uplight/Downlight Control:

Up Light: Press and release the button to turn

the up light on/off. Press and hold the button to

activate dimming function and release once the

desired brightness level is reached.

Down Light: Press and release the button to

turn the down light on/off. Press and hold

the button to activate dimming function and

release once the desired brightness level is

reached.

Warm weather - (Forward) A downward air

flow creates a cooling effect as shown in Figure

24. This allows you to set your air conditioner

on a higher setting without affecting your

comfort.

Cool weather - (Reverse) An upward air flow

moves warm air off the ceiling are as shown in

Figure 25. This allows you to set your heating

unit on a lower setting without affecting your

comfort.

Remote Control

Timer:

While the fan is on press 2h - turns on a 2 hour

run timer.

While the fan is on press 4h - turns on a 4 hour

run timer.

While the fan is on press 8h - turns on an 8 hour

run timer.

Forward/Reverse:

Changes direction of ceiling fan.

Breeze:

Press and release this button to enable the

Breeze function, this will change your fan

speed randomly, simulating a relaxing breeze.

Fan speed:

LEDs on the fan speed button will illuminate

to the corresponding speed.

Press and release 1: turns the fan speed to 1.

Press and release 2: turns the fan speed to 2.

Press and release 3: turns the fan speed to 3.

Press and release 4: turns the fan speed to 4.

Press and release 5: turns the fan speed to 5.

Press and release 6: turns the fan speed to 6.

Fan OFF:

Turns fan Off

Lights ON/OFF

Press and release the lights on button to turn

both lights on to the last setting.

Press and release the lights off button to turn

both lights off.

11. Operating Your Fan

Forward/

Reverse

Fan speed

2h

4h

8h

2

3 4

OFF

1 6

5

Timer

Breeze

Fan off

Lights on

Lights off

Uplight

Downlight

R

Figure 23

Figure 24

Figure 25

Care of Your Fan

Here are some suggestions

maintain your fan.

to help you

1. Because of the fan’s natural movement,

some connections may become

loose.

Check the support connections, brackets,

and blade attachments twice a year. Make

sure they are secure. (It is not necessary to

remove fan from ceiling.)

2. Clean your fan periodically to help maintain

its new appearance over the years. Do

not use water when cleaning, this could

damage the motor, or possibly cause an

electrical shock. Use only a soft brush

or lint-free cloth to avoid scratching the

finish. The plating is sealed with a lacquer

to minimize discoloration or tarnishing.

Warning - Make sure the power is off

before cleaning your fan.

3. You can apply a light coat of furniture polish

to the wood for additional protection and

enhanced beauty. Cover small scratches

with a light application of shoe polish.

4. There

is no need to oil your fan.

lubricated

The motor has permanently

sealed ball bearings.

Troubleshooting

Problem

Fan will not start

Solution

1. Check main and branch circuit fuses or breakers

2. Check line wire connections to the fan and switch wire connections in

the switch housing. CAUTION: Make sure main power is off.

3. Check batteries in the transmitter. Does the red LED light come on?

Are you standing close enough to the fan? (Normal range is 10-20

feet.) Are the dip switch settings the same on the transmitter (hand unit)

and receiver? REMEMBER TO TURN OFF POWER SUPPLY

BEFORE CHECKING THE DIP SWITCH SETTINGS IN

RECEIVER.

Fan sounds noisy

1. Make sure all motor housing screws are snug.

2. Make sure the screws that attach the fan blade bracket to the motor hub

are tight.

3. Make sure wire nut connections are not rattling against each other or

the interior wall of the switch housing.

CAUTION: Make sure power is off.

4. Allow a 24-hour “breaking in” period. Most noises associated with a

5.

new fan disappear during this time.

If using the Ceiling Fan light kit, make sure the screws securing the

glassware are tight. Check that the light bulb is also secure.

6. Make sure the canopy is a short distance from the ceiling.

It should not touch the ceiling.

7. Make sure your electrical box is secure and rubber isolator pads were

used between the mounting bracket and electrical box.

MAKE SURE THE POWER IS OFF AT THE ELECTRICAL PANEL BOX

BEFORE YOU ATTEMPT TO MAKE ANY REPAIRS. REFER TO THE SECTION,

“MAKING ELECTRICAL CONNECTIONS.”

12. Care of Your Fan and Troubleshooting

FAN

SIZE

54”

SPEED

VOLTS

FAN POWER

CONSUMPTION

(WITHOUT LIGHTS)

WATTS

AIRFLOW

CFM

AIRFLOW

EFFICIENCY

(HIGHER IS BETTER)

CFM/WATT

NET

WEIGHT

GROSS

WEIGHT

CUBE

FEET

Low

High

120

2.27

29.73

2317

6477

1020.7

217.86

17.42

Lbs

19.62

Lbs

1.72

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits

are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate

radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio

or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one

or more of the following measures:

--Reorient or relocate the receiving antenna.

--Increase the separation between the equipment and receiver.

--Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

--Consult the dealer or an experienced radio/TV technician for help.

CAUTION:

Any changes or modifications not expressly approved by the grantee of this device could void the user’s authority to operate the equipment.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful

interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

13. Specifications

©2017 Progress Lighting, Inc.

701 Millennium Blvd.,

Greenville, SC 29607

All Rights Reserved



 

 

 

 

 

 

 

 

 

 

This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions (1) this device may not cause harmful interference, and

(2) this device must accept any interference received, including interference that may cause undesired operation.

 

 

 

 

 

 

 

 

 

 

Sep 06, 2021

Federal Communications Commission

Authorization & Evaluation Division

7345 Oakland Mills Road

Columbia, Maryland 21046

Authority to Act as Agent

On our behalf, I appoint Shenzhen Timeway Testing Laboratories/ Zone C, 1st Floor,

Block B, Jun Xiang Da Building, Zhongshan Park Road West, Tong Le Village, Nanshan

District, Shenzhen, China (Name of Agent company name and address) to act as our

agent in the preparation of this application for equipment certification. I certify that

submitted documents properly describe the device or system for which equipment

certification is sought. I also certify that each unit manufactured, imported or marketed, as

defined in the Federal Communications Commission’s regulations will have affixed to it a

label identical to that submitted for approval with this application.

For instances where our authorized agent signs the application for certification on our

behalf, I acknowledge that all responsibility for complying with the terms and conditions

for certification, still resides with K i n g o f F a n s , I n c . / 1951 N.W. 22nd Street, Fort

Lauderdale, FL33311, USA

<Signature>：

Name：Charles Bucher

Title：

Company：King of Fans, Inc.



 

 

Sep 06, 2021

Equipment Autorisation Division

Federal Communications Commission

7435 Oakland Mills Road

Columbia, MD 21046

FCC ID: RGB-P250061D

Product Name: P250061

Request for Confidentiality

Pursuant to Sections 0.457 and 0.459 of the commissions rules, we hereby request that

the following documents be held confidential:

• Schematics

• Block diagram

• Operation description

These materials contain trade secrets and proprietary information and are not

customarily released to the public. The public disclosure of this information might be

harmful to the company and provide unjustified benefits to our competitors.

<Signature>：

Name：Charles Bucher

Title：

Company：King of Fans, Inc.