PORTABLE SOUND SYSTEM Model No.: KP818 Read this booklet thoroughly before using and save it for future reference Unit must be fully charged before use FCC COMPLIANCE STATEMENT:
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired operation. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. Warning: Changes or modifications to this unit not expressly approved by the part responsible for compliance could void the users authority to operate the equipment. FCC Radiation Exposure Statement The device has been evaluated to meet general RF exposure requirement. The device can be used in mobile(min20cm) exposure condition without restriction. IC Notice:
This device complies with Canada Industry licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference. and (2) this device must accept any interference. Including interference that may cause undesired operation of the device. CAN ICES-3 (B) Le prsent appareil est conforme aux CNR dIndustrie Canada applicables aux appareils radio exempts de licence. Lexploitation est autorise aux deux conditions suivantes :
(1) lappareil ne doit pas produire de brouillage; (2) lutilisateur de lappareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible den compromettre le fonctionnement. NMB-3 (B) 1 1. Minimum distances 30cm around the apparatus for sufcient ventilation;
2. The ventilation should not be impeded by covering the ventilation openings with items, such as newspapers, table-cloths, curtains, etc.;
3. No naked flame sources, such as lighted candles, should be placed on the apparatus;
4. Attention should be drawn to the environmental aspects of battery disposal;
5. The use of apparatus in moderate climates. 6. WARNING : To reduce the risk of fire or electric shock, do not expose this apparatus to rain or moisture;
same or equivalent type;
7. CAUTION : Danger of explosion if battery is incorrectly replaced. Replace only with the 8. Batterie shall not be exposes to excessive heat such as sunshine, fre, etc. 9. Where the MAINS plug or an appliance coupler is used as the disconnect device, the disconnect device shall remain readily operable;
The lightning flash with arrowhead symbol, within an equilateral triangle is intended to alert the user to the presence of uninsulated dangerous voltage within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. This equipment is a Class II or double insulated electrical appliance. It has been designed in such a way that it does not require a safety connection to electrical earth. Direct current Alternating current 1. 30cm distance minimale autour de l'appareil pour une aration suffisante;
2. Il convient que l'aration ne soit pas gne par l'obstruction des ouvertures d'aration par des objets tels que journaux, nappes, rideaux, etc.;
3. Il convient de ne pas placer sur l'appareil de sources de flammes nues, telles que des 4. Il convient d'attirer l'attention sur les problmes d'environnement dus la mise au dchet bougies allumes;
des piles;
5. Si l'appareil est destin tre utilis sous un climat tempr;
6. ATTENTION : Pour rduire le risque du feu et du choc lectrique, ne pas exposer cet appareil aux pluies ou l'humidit;
7. ATTENTION : Danger d'explosion si la pile n'est pas remplace correctement. Ne remplacer que par le mme type ou un type quivalent;
8. La batterie ne doit pas tre expose une chaleur excessive telle que le soleil, le feu ou similaire. 9. Lorsque la prise du RSEAU D ALIMENTATION ou une prise place sur lappareil est utilise comme dispositif de dconnexion, ce dispositif doit demeur aisment accessible;
Le symbole en forme d'clair avec une pointe de flche dans un triangle quilatral est destin alerter l'utilisateur de la prsence dans l'appareil d'un voltage non-isol dangereux pouvant tre d'une puissance suffisante pour constituer un risque d'lectrocution. Le point d'exclamation dans un triangle quilatral est destin alerter l'utilisateur de la prsence d'instructions d'utilisation et de maintenance (entretien) importantes dans la documentation accompagnant l'appareil. Ce matriel appartient la classe Il ou un appareil lectrique double isolation. Il a t conu de telle so e qu'il ne ncessite pas de connexion de scurit la mise la terre. Courant continu Courant alternatif Ins truc tion s 5 Instructions de scurit importantes 1. Lisez ces instructions. 2. Conservez ces instructions. 3. Respectez tous les avertissements. 4. Suivez toutes les instructions. 5. Ne pas utiliser cet appareil proximit de leau. 6. Nettoyez uniquement avec un chiffon sec. 7. Ne jamais boucher les ouvertures de la ventilation. Installez lunit conformment aux instructions du fabriquant. 8 . Ne pas installer prs dune source de chaleur telle que des radiateurs, des registres de chaleur,
broche de terre. La lame large ou la troisime broche sont fournies pour votre scurit. Lorsque
obsolte. 10. vitez que le cordon dalimentation ne soit pitin ou pinc, en particulier sur les prises, les multiprises et au niveau de la sortie de lappareil.
12. Utilisez uniquement avec le chariot, le stand, le trpied, le support ou la table recommande par le fabricant, ou vendu avec lappareil. Lorsquun chariot est utilis, faites attention lors du dplacement de la combinaison du chariot/appareil pour viter de vous blesser en cas de chute. 13. Dbranchez cet appareil pendant les orages ou lorsquil nest pas utilis pendant une longue priode.
sont endommags, du liquide a t renvers ou des objets sont tombs dans lappareil, lappareil a t expos la pluie ou lhumidit, sil ne fonctionne pas normalement, ou sil est tomb. 15. Avertissement pour rduire le risque dincendie ou de dcharge lectrique : ne pas exposer cet appareil la pluie ou lhumidit. Lappareil doit tre gard labri des gouttes ou des claboussements deau ; ne posez jamais un objet contenant de leau sur cet appareil, par exemple un vase. 16. Le systme dantenne extrieure ne devrait pas tre situ proximit de lignes lectriques ariennes ou dautres circuits dclairage ou dalimentation lectrique, ou un endroit o il peut tomber sur ces lignes ou circuits lectriques. Lors de linstallation dun systme d antenne extrieure, prenez extrmement soin de ne pas toucher ces lignes ou circuits lectriques, car tout contact peut tre fatal. 17. Ne pas surcharger les prises murales et les cbles de rallonge, car cela peut entraner des risques dincendie ou dlectrocution. 18. Ne pas introduire dobjets par les ouvertures de cet appareil, car ils pourraient entrer en contact avec des points de tension dangereux ou court-circuiter des pices qui pourraient provoquer des incendies ou une dcharge lectrique. Ne jamais verser ou pulvriser de liquide quel quil soit sur lunit. 6
/TUN.- BUTTON PRODUCT OVERVIEW Top View 1. USB PORT 2. 3.5mm AUX IN JACK 3. 6.3mm MIC JACK 1 4. 6.3mm MIC JACK 2 5. USB CHARGE PORT 6. PAIR/TWS BUTTON 7. STANDBY BUTTON 8. VOLUME CONTROL 9. 10/M./FOLDER + BUTTON 10. 10/M./FOLDER - BUTTON 11. EQ BUTTON
/TUN.+ BUTTON 12. 13. FUNCTION BUTTON 14. LIGHT BUTTON 15.
/SCAN BUTTON 16. P-MODE/M. BUTTON 17. MUTE BUTTON 18. 19. ECHO BUTTON 20. MIC VOL.- BUTTON 21. MIC VOL.+ BUTTON 22. EX-BASS BUTTON Front and Back view 23. LCD DISPLAY 24. PAIR INDICATOR 25. CHARGE INDICATOR 26. DISCO LED LIGHT 27. SPEAKER GRILLE 28. SPEAKERS 29. TWEETER 30. PROJECTION LIGHT 31. STROBE LIGHT 32. FM ANTENNA 33. VENTILATION HOLES 34. AC SOCKET 2 Getting Started POWER SOURCE This unit works with rechargeable lead-acid battery (the battery capacity 4000mAh). Fully charge the unit (around 7 hours) before using the product for the first time. The playback time has about 2hours after full charging. Unplug the AC Power cord from the AC socket to work on the battery pack after fully charged. Plugging the AC Power cord while the battery pack is attached initiates the charging of this battery, the charge LED indicator lights red during charging, when the battery is fully charged the indicator will turn to green. When the unit is with low battery, the LED indicator will flash in red. Warning: Do not change the battery, only high-qualified personnel can perform this operation. OPERATION INSTRUCTION BASIC FUNCTION TURNING THE UNIT ON/OFF Press and hold the STANDBY button to switch the unit on/off. SETTING THE FUNCTION MODE To change the function modes, press the FUNCTION button repeatedly to choose USB/BLUETOOTH/AUX/RADIO function. ADJUSTING THE VOLUME 1. Rotate the VOLUME knob on the unit to increase or decrease the music volume. 2. Press the MIC VOL.+/- button on the unit to increase or decrease the microphone volume. BASS ADJUSTMENT Press the EX BASS button on unit to increase the bass effect. EQUALIZER (EQ) FUNCTION This unit has a built-in equalizer system, Press the EQ button on unit to select a setting that best matches the music style: FLAT, POP, CLASSIC, JAZZ, and ROCK. USB CHARGING This unit provides a 5V 1A USB charging port for charging your smart phone. Connect the USB cable of your smart phone to the USB CHARGE port for charging. MICROPHONE ECHO ADJUSTMENT Press the ECHO button on unit turn on or off the microphone echo effect. FLASHING LIGHT There are 5 flashing modes for the DISCO LED lights. Press the LIGHT button to choose the light modes. To turn off the light, press the LIGHT button until OFF showed on the display. The projection light and strobe light will flash to the music beat in all light modes. Press and hold the LIGHT button to turn it on or off.. 3 RADIO OPERATION Listen to FM radio broadcasts. Press the FUNCTION button on the unit, the display reads FM and the radio frequency. Note: in order to get the best reception, extend the FM antenna on the rear of the unit before use to its full length. TUNING TO A RADIO STATION If you know the station frequency that you want to tune to directly:
Tune to a station by press the
/TUN.+ or
/TUN.- button repeatedly. The station frequency is shown on the display. AUTOMATIC TUNING STOP Press and hold the automatically when a station is received.
/TUN.-BUTTON or AUTO PRESET MEMORY / SCAN
/TUN.+BUTTON to start tuning, tuning stop To scan for stations within reception range and save them to preset memory automatically, press and hold the PLAY/PAUSE/SCAN button. After the unit is finished scanning, the unit will automatically tune to preset number 1 (P01). To tune to a preset station:
To tune to the next preset station, press the 10/MEM./FOLDER + button. To tune to the previous preset, press the 10/MEM./FOLDER - button. MANUAL PRESET MEMORY OPERATION Choose which stations to save in preset memory instead of scanning automatically. 1. Use the
/TUN.+ or
/TUN.- button to tune to the station that you want to save as a preset (e.g., 93.1). 2. Press the P-MODE/M. button. will flash on the display to indicate that you are saving the station as Preset Memory 01. (To change the preset memory number, press the 10/MEM./FOLDER + or 10/MEM./FOLDER - buttons.) 3. Press the P-MODE/M. button to finish saving the station (e.g., P01 is now set to 93.1). 4. To save another station, repeat steps 1 to 3. You may save up to 30 FM stations. USB OPERATION 1. Press the FUNCTION button on unit to select USB mode. 2. Plug the USB memory stick to the USB port on top of the unit. Playback will start 3. To pause playback, press the PLAY/PAUSE/SCAN button on unit. The playing time will flash automatically from Track 1. on the display. 4. To resume playback, press the PLAY/PAUSE/SCAN button again. 5. To select a desired track, press the button respectively during playing until the or desired track appears on the display. The unit will start play automatically. 4 button to 6. To search for a particular passage during playback, press and hold the or scan the current playing track at high speed until desired point (passage) appears, then release the button for normal playback mode. 7. To select a song which track number exceeds 10, press the 10/MEM./FOLDER + or 10/MEM./FOLDER - button each time to skip forward/backward 10 tracks, then press the or button to select desired track. 8. To select a desired folder (if the USB contains more than one folder), press and hold the 10/MEM./FOLDER + or 10/MEM./FOLDER - button each time to skip forward/backward a folder, then press the button to select desired track. or Important: The USB port is intended for data transfer only, other devices cannot be used with this USB connection. The use of USB extension cords is not recommended. Dont plug the USB from the unit when playing or reading the USB device. REPEAT PLAY You can play one track or all tracks on the USB repeatedly. To Repeat a Single Track 1. Press P-MODE/M. button on unit during play, the display will show will be played over and over again. and the current track 2. To cancel repeat play, press P-MODE/M. button on unit until disappears from the display. To repeat all the Tracks 1. Press P-MODE/M. button on unit until the on the USB will be played over and over again. ALL shows steadily on the display, all tracks 2. To cancel repeat play, press the P-MODE/M. button on unit until ALL disappears from the display. the display. To repeat the folder (only for USB which contains more than one folder) 1. Press the P-MODE/M. button on unit until DIR shows steadily on the display, the current folder will be repeated over and over again. 2. To cancel repeat play, press the P-MODE/M. button on unit until DIR disappears from RANDOM PLAY Press the P-MODE/M. button on unit in play mode till the RAN shows steadily on the display, the random play will start from next track automatically. Press the P-MODE/M. button on unit again until the RAN disappears from the display to cancel. BLUETOOTH OPERATION 1. Press the FUNCTION button on unit to switch to BLUETOOTH function, the LCD will display and the pair indicator will flash at high speed. 2. Turn on the Bluetooth function on the device, scan the unit TY-ASC75 and connect, then input the password 0000 if required, the pair indicator keep light up to indicate connection done, and the display will show
. Press Play to start playback. 3. Rotate the VOLUME knob on the unit or adjust the volume on the external device to increase or decrease the music volume to your desired level. 4. Press the PAIR/TWS button to disconnect Bluetooth. Note: The Bluetooth works best within 10 meters in open air. 5 TWS OPERATION If you have two units of this model, you can connect the two units by TWS function to become stereo output. 1. Connect the device to one of the units by Bluetooth function, this unit will become the master unit. 2. Turn on the second unit and switch to Bluetooth mode 3. Press and hold the PAIR/TWS on the first (master) unit, then these two units will connect automatically with a sound indicated that the connection is done. The master unit will show TWS R and the second unit will show TWS L, then these two units will become stereo output. 4. Control of play, pause, next track and previous track can be done by both units. Rotate the volume knob on each unit to adjust the volume individually. 5. To quit the TWS between the two units, press the PAIR/TWS button on the second unit to disconnect the TWS. 6. To quit the Bluetooth from the mobile, press the PAIR/TWS button on the first (master) unit. AUX-IN OPERATION 1. Press the FUNCTION button on unit to select the AUX mode. 2. Connect your audio device to the AUX IN jack on the top panel of the unit with an AUX IN cable.(audio cable is not included) 3. Rotate the VOLUME knob on the unit or adjust the volume on the external device to increase or decrease the music volume to your desired level. 4. Control the playback with your audio device. MIC JACK OPERATION Microphone input is available in all modes. 1. Connect your microphone to the 6.3mm MIC JACK found on the top panel of the unit. 2. Press the MIC VOL.+/- button on the unit to increase or decrease the microphone volume. 3. Press the ECHO Button to turn on or off the echo effect of the microphone. 6 Technical Specifications GENERAL Power Requirements AC100-240V~60/50Hz Power consumption 36W Power output 25W X 2 FM frequency FM 87.5-108mHz AUX in jack 3.5mm Microphone jack 6.3mm Work temperature 5C - +35C Bluetooth Communication system Bluetooth Standard version 5.0 Reception Range 10 meter (line-of-sight distance) Compatible Bluetooth profiles Advanced Audio Distribution Profile (A2DP) ACCESSORIES Instruction Manual x 1pc AC Cord x 1pc Wired Microphone x 1pc Note: Specifications are subject to change for continuous improvement without prior notice. 7