Waterproof Wireless Speaker
User’s Manual
Introduction
Thank you for choosing the F2 as your source for
entertainment, you can use this item with iPads,iPhones,
iPods and many types of smart-phone to stream music ,
and enjoy hands-free calling.In order to get the best results
when using the device,please read this manual first before using.
Feartures
-Volume and song control directly on speaker unit
-Stunning sound clarity
-Ultra portable design
-Great for parties, indoor and outdoor
-Allow you to make and answer phone calls
-
F2
1 2
3
8
9
4
5
6
7
1.Previous / Volume –
2.ON/OFF button
3.Next / Volume +
4.Green LED(AUX)
5.Red LED(Charging)
6.Blue LED(Bluetooth)
7.Phone /play button
8.MIC
9.Micro USB Charging/AUX in Port
Included:
1.Speaker
2.USB Micro Charging Cable
3.3.5 mm Micro-USB Cable
4.User Manual
Specifications
Supported Profiles:A2DPV1.2 ,AVRCPV1.4,
HFPV1.5,HSP1.2,GAVDP1.2
Bluetooth Range:33ft (10m)
Dimensions: 208*80*80 mm
Battery: Li-Ion 3.7V/2000mAh
Charging: 5V @ 1 A
Operation
Powering On
Press and Hold "ON/OFF" button 2 seconds to power ON, the
Blue LED will start to flash.
If an AUX (3.5 mm) cable is connected to the unit, the Blue LED
will turn off , and the Green LED will stay illuminated,notifying you
the unit is in Aux-In mode.
Powering Off
Press and Hold "ON/OFF" button 2 seconds to power OFF
Bluetooth Mode
Pairing
The unit will automatically go into “Pairing Mode” when it is
powered ON.
Go into your Bluetooth device settings menu and look for “F2”
After the unit has paired and connected, it will re-connect
automatically when the unit is powered on and the device
is in range.
Note: Bluetooth Timeout :10 minutes
Begin Streaming Music
Press “ ” to start playing music.
Press and Hold “ ” 2 seconds to play the next track.
Press and Hold “ ” 2 seconds to play the previous track.
Press either “ ” or “ ” for volume control.
Making and Receiving Phone Calls
When the unit is connected and paired to your device,
the unit allows you to make or receive phone calls with its
built-in microphone.
Press “ ” to accept a call
To end a call press“ ”
To place a call, simply dial the number or select a contact form
To reject a call, press and hold “ ” for 2 seconds
Aux-In Mode
Plug in the supplied 3.5 mm cable into the unit. The other end is
connected to your device. The Green LED will stay illuminated.
It means in “Aux” mode.
Please note music can be controlled by your device.
Charging
Attach the USB cable to the unit, and plug into any USB charger.
If the unit is completely discharged, it will take approximately 4
hours to fully charge.
The Red LED will illuminate during charging, when it has
completed, the Red LED will turn off.
Note:There will be a beep when the battery is low and needs to
be recharged.
LED Status
Blue LED solid
Bluetooth Mode
Green LED on solid
Aux Mode
Red LED
Charging
Troubleshooting
Unit doesn’t connect
to device
Speaker needs to be connected/
re-paired to device
Atone is heard every few seconds
Speaker needs to be charged
Unit will not power on
Speaker needs to be charged
Unit doesn’t control
track(s)/volume
Speaker needs to be in Bluetooth
mode for full control
Unit distorts at
high volume
The devices’ volume needs to
be lowered
FCC Statement：
This device complies with Part 15 of the FCC rules. Operation is subject
to the following two conditions: 1) this device may not cause harmful
interference, and 2) this device must accept any interference received,
including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC rules. These limits
are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses
and can radiate radio frequency energy and if not installed and used in
accordance with the instructions, may cause harmful interference to
radio communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged
to try correct the interference by one or more of the following measures:
- Reorient the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into and outlet on a circuit different from that
to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Changes or modifications not expressly approved by the party
responsible for compliance could void your authority to operate the
equipment.