CONNECTING TO OTHER AUDIO SOURCES Note: Before connecting to other audio source, make sure to disconnect the Bluetooth connection between the docking station and the Bluetooth enabled device. 1.Press [INPUT] button to select Auxiliary Input, the AUX green LED will light. 2.Insert one end of the 3.5mm stereo input cable into the "AUX IN" jack on the back of the docking station. Then insert the other end of the 3.5mm audio cable into your audio source, such as MP3 player, portable CD player, etc. 3.Tum on your audio source and play music. 4.You can press the [VOL +][VOL-] buttons on the docking station to increase or decrease the volume. ACCESSORIES 3.5mm Stereo Input USB Cable x 1 Cable x 1 AC Adapterx 1 Remote Control x 1 This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
-- Reorient or relocate the receiving antenna.
-- Increase the separation between the equipment and receiver.
-- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-- Consult the dealer or an experienced radio/TV technician for help. RF Exposure Information:
To comply with FCC RF exposure compliance requirement, this grant is applicable to only mobile configurations. The antenna used for this transmitter must be installed to provide a separation distance of at lease 20cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter. 8 ata. PAIRING WITH BLUETOOTH ENABLED DEVICES Note: You are required to pair the system with your Bluetooth enabled devices (mobile phone, MP3 player, PDA and computer) before use. Mobile Phone Portable Media Player Computer S Lo or |
o PEE ae og
; Keep the dietanes:
Keep the diate lesa than 1 mater lesa than 1 meter When initiating the pairing, keep the distance between the system and the Bluetooth wireless technology enabled device less than 3 Feet (1 meter). Make sure there is no other Bluetooth wireless technogy enabled device nearby. 1. Press [INPUT] button to select Bivetoofh connection, green Bluetooth LED will light. 2. This will automatically initiate the Biuefooth pairing process. The blue and red LED will flash alternately. 3. Alternative: To manually start the Bivefooth pairing process press and hold "}"Pairing button on the panel until the blue and red LED flash alternately. You are in the pairing mode. 4. Turn on the Bluetooth connection on your Bluetooth enabled device and perform a search for Bluetooth devices in range.
(Refer to the user's guide of your Biuvetootf enabled device for more detailed information.}
5. When the search is completed, your Bluetooth enabled device will display a new device named
"ARTDIO" in the list of Bluetooth devices. Select "ARTDIO" from the list. 6. You will be prompted to enter a passkey. Enter the default passkey 0000. 7. When the blue LED light is flashing constantly it indicates that the pairing process has been successfully completed. Your Bluetooth enabled device and the system are now connected through Bluetooth wireless technology. 8. The LCD screen on your Biuefooth enabled device should display a Bluetooth or audio icon ")" to indicate Biuetooth connection. Note: If the pairing cannot be completed in 90 seconds, the blue and red LED will stop flashing and the Biueiooth pairing process will be terminated. Please start the pairing process again. 9. Now you may select music from your Bivetooth enabled device and play it wirelessly through the systern. START PLAYING BLUETOOTH MUSIC 1.Select and play music from your Bluefooth enabled device. 2.Press [VOL+] [VOL -] buttons on the docking station or remote contral will increase or decrease the volume. 3.The remote contral allows you to play/pause, go to previous or go to next for your Bluetooth music.
(Please see Remote Control on page 4 for details)