FCC ID: 2AU2UKIPIT00-1 RFID Liner Tote Device

KIPIT [name of device]

[model No.]

[FCC ID: ]

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. CAUTION: CHANGES OR MODIFICATIONS NOT EXPRESSLY APPROVED BY THE PARTY RESPONSIBLE FOR COMPLIANCE COULD VOID THE USER'S AUTHORITY TO OPERATE THE EQUIPMENT. Responsible party: Kipit, Inc. [Address] [Telephone or internet contact information]

A. INSTALLATION AND OPERATION NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. NOTE: The Kipit Tote Liner is designed for the average sized women's tote, which is roughly 32cm deep, 16cm wide, and 34cm long. With these dimensions, the Kipit Tote Liner is required to be installed in a U-shape formation, going down the 2 long sides of the bag and across the width of the bottom of the bag. Under these conditions, the liner is not in a flat configuration, and installation instructions make clear that the Kipit Tote Liner is not to be used in a flat configuration. Upon receiving the Kipit Tote Liner, users are instructed to install the device in the U-shape formation seen in the accompanying photographs, and to affix it with Velcro patches so that it does not shift into any other configuration. This ensures that the Liner remains in a U-shape formation while in use. 1. Package components 1 piece 1 piece 5 pieces 2. Reader elements

[Drawing/Photo of reader with explanation of buttons, light indicators, connectors, etc.]

A. USB port B. Battery indicator C. LED area D. Velcro strips E. Reset Button 3. Preliminary steps Reader USB cable Stickers I. Take reader out of the packaging. II. Connect the reader to a power source using the USB cable to activate it. A light will flash green on the device. Fully charge reader until the light turns from flashing green to solid green. III. IV. Disconnect from power source. 4. Placing the reader inside your bag I. Place reader inside bag. Velcro strips must face the sides of the bag. Peel cover off Velcro strips. II. III. Adjust the reader so it covers the bottom and sides of the bag. IV. V. Download the Kipit app and follow instructions to connect to device and use. Press firmly the Velcro strips to secure the reader in place. B. SAFETY This Kipit device contains a rechargeable battery cell. Please review and adhere to the following safety instructions:

DO NOT INCINERATE, DISASSEMBLE, EXPOSE THE DEVICE TO HIGH TEMPERATURE 212F (100C) DUE TO RISK OF FIRE OR EXPLOSION. IF BATTERY CELL BECOMES SEPARATED FROM DEVICE, DO NOT INCINERATE, DISASSEMBLE, EXPOSE TO HIGH TEMPERATURE 212F (100C) OR SHORT THE BATTERY TERMINALS DUE TO RISK OF FIRE OR EXPLOSION. DO NOT OVERHEAT THE DEVICE BY EXPOSING IT TO DIRECT SUNLIGHT. DO NOT OVERCHARGE THE DEVICE. DO NOT FORCE DISCHARGE THE BATTERY OF THE DEVICE. DO NOT OPEN OR DISASSEMBLE ANY PARTS OF THE DEVICE. DO NOT DISMANTLE, DEFORM OR MODIFY THE BATTERY CELL OF THE DEVICE. IN CASE OF INGESTION OF THE BATTERY CELL, THE PERSON INVOLVED SHOULD SEEK MEDICAL ASSISTANCE PROMPTLY. IF DEVICE OVERHEATS, DISCONNECT CHARGER, IF CONNECTED, AND PLACE AWAY FROM FLAMMABLE MATERIALS. IF ANY VISIBLE SWELLING, SMELL OR LEAKS FROM THE BATTERY CELL OCCUR, DISCONTINUE USE OF DEVICE. IF BATTERY CELL BECOMES SEPARATED FROM DEVICE, INSULATE THE SOLDER TAGS BY WRAPPING THEM WITH TAPE OR FOIL. A BATTERY WITH A DAMAGED POUCH SHOULD NOT BE EXPOSED TO WATER. Follow local, state and federal regulations on proper disposal. Contact a local battery recycling center for disposal instructions. The Kipit device complies with portable radiofrequency (RF) exposure limit in the USA set forth for an uncontrolled environment and is safe for intended operation as described in this manual. Further RF exposure reduction can be achieved if the product is to be kept away from the user body when device is not in use (for example, do not sleep on a bag with an active device placed in it).

Back of product 23 in 10.5 in FCC Label Electronics FCC Label Information Text: FCC ID 2AU2UKIPIT00-1 Contains FCC ID: QOQBGM12LMA This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Font: size 4 font Adhesive: permanent adhesive, type TT200, specifically Flexcon L344

THIS MUST BE SIGNED BY THE APPLICANT/AGENT AND SHOULD BE PLACED ON APPROPRIATE LETTERHEAD Authority to Act as Agent Date: July 13, 2020 American Certification Body, Inc. 6731 Whittier Avenue Suite C110 McLean, VA 22101 To Whom It May Concern:

Nic Johnson of the Nebraska Center for Excellence in Electronics (NCEE Labs) is authorized to act on our behalf, until otherwise notified, for applications to American Certification Body, Inc. (ACB). We certify that we are not subject to denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 862. Further, no party, as defined in 47 CFR 1.2002 (b), to the application is subject to denial of federal benefits, that includes FCC benefits. We also declare that the information provided to the FCC is true and correct to the best of our knowledge (47 CFR 2.911(d)) and we have been informed of the grantee responsibilities (47 CFR 2.909) with regard to certified equipment. Thank you, Agency Agreement Expiration Date: 12 months By:

Title:

On behalf of: Kipit, Inc. Telephone:

__________________________ Elizabeth Harkins

(Print name)

(Company Name)

(917) 208-0100

(Signature) CEO

Date: July 23, 2020 Subject: Confidentiality Request for:

Request for Confidentiality Pursuant to FCC 47 CFR 0.457(d), the applicant requests that a part of the subject FCC application be held confidential. FCC ID: 2AU2UKIPIT00-1 Type of Confidentiality Requested Short Term Short Term Short Term Short Term Short Term Short Term Short Term Short Term Short Term Not Provided Permanent Not Provided Permanent Not Provided Not Provided Permanent Not Provided Permanent Not Provided Permanent Permanent Not Provided Not Provided Permanent Not Provided Exhibit Block Diagrams External Photos Internal Photos Operation Description/Theory of Operation Parts List & Placement/BOM Tune-Up Procedure Schematics Test Setup Photos Users Manual The above-mentioned company has spent substantial effort in developing this product and it is one of the first of its kind in industry. Having the subject information easily available to "competition" would negate the advantage they have achieved by developing this product. Not protecting the details of the design will result in financial hardship. Permanent Confidentiality:

The applicant requests the exhibits listed above as permanently confidential be permanently withheld from public review due to materials that contain trade secrets and proprietary information not customarily released to the public. Short-Term Confidentiality (if applicable): Not Applicable The applicant requests the exhibits selected above as short term confidential be withheld from public view for a period of 180 days from the date of the Grant of Equipment Authorization and prior to marketing. This is to avoid premature release of sensitive information prior to marketing or release of the product to the public. Applicant is also aware that they are responsible to notify ACB in the event information regarding the product or the product is made available to the public before the requested period has expired. ACB will then release the documents listed above for public disclosure pursuant to FCC Public Notice DA 04-

1705. NOTE for Industry Canada Applications:

IC currently only distinguishes Permanent Confidentiality exhibits as shown above. Short Term confidentiality is not considered Provided to IC applications Sincerely, By:

__________________________ Nic Johnson, Technical Manager, NCEE Labs Page 1 of 1