INDICATOR LIGHT GUIDE Solid white light Main router: Connected to broadband. Sub router: Connected to the main router and signal is strong. Flashing white light Main router: Connection to broadband is intermittent. Sub router: Connected to the main router but signal is weak. Try moving it closer to the main router. Solid amber light Main router: Ready for conguration. Sub router: Ready to connect to the main router. Flashing amber light Sub router: Pairing and syncing with the main router. Solid red light System is starting up. This will take about a minute. Flashing red light Main router: Unable to connect to broadband. Follow these steps to troubleshoot:
1. Make sure the WAN/LAN port is connected to the modem with an Ethernet cable. 2. Make sure the Ethernet cable is securely plugged in and not damaged. 3. Check if the modems broadband settings are correct. If the Internet access method is DHCP, the router can directly access the Internet. If the Internet access method is PPPoE, make sure you have entered the correct broadband account name and password provided by your broadband operator. 4. Check if your broadband connection is working properly. Sub router: Unable to connect to the main router. Follow these steps to troubleshoot:
1. Move the sub router closer to the main router. 2. Reset the sub router to factory settings. 3. Make sure you have completed the setup process in the app. FCC Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. Caution: Any changes or modications to this device not explicitly approved by manufacturer could void your authority to operate this equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. RF Exposure Information This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator and your body. ISED Statement This device contains licence-exempt transmit-
ter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canadas licence-exempt RSS(s). Operation is subject to the following two conditions:
(1) This device may not cause interference.
(2) This device must accept any interference, including interference that may cause undesired operation of the device. The digital apparatus complies with Canadian CAN ICES3 (B)/NMB3(B). Cet appareil contient des metteurs/rcepteursexempts de licence qui sont conformes aux RSSexempts de licence d'Innovation, Sciences etDveloppement conomique Canada. L'exploitation est soumise aux deux conditionssuivantes :
(1) Cet appareil ne doit pas provoquer d'interfrences.
(2) Cet appareil doit accepter toute interfrence, ycompris les interfrences susceptibles de provoquerun fonctionnement indsirable de l'appareil. l'appareil numrique du ciem conforme canadienpeut 3 (b) /
nmb 3 (b). radiationexposure limits This device meets the exemption from the routine evaluation limits in section 2.5 of RSS 102 and compliance with RSS 102 RF exposure,users can obtain Canadian information on RFexposure and compliance. This equipment complies with Canada set forth for an uncontrolledenvironment. This equipment should be installed and distance 20cm between theradiator & your body. cet appareil est conforme l'exemption des limites d'valuation courante dans la section 2.5du cnr - 102 et conformit avec rss 102 de l'exposition aux rf, les utilisateurs peuvent obtenir des donnes canadiennes sur l'exposition aux champs rf et la conformit.Cet quipement est conforme aux limites d'exposition aux rayonnements du Canadatablies pour un environnement non contrl.Cet quipement doit tre install et utilis une distance minimale de 20 cm entre leradiateur et votre corps. operatedwith minimum The device for operation in the band 51505250 MHz is only for indoor use to reduce the potentialfor harmful interference to co-channel mobile satellite systems. L'appareil destin fonctionner dans la bande 5150-5250 MHz est uniquement destin uneutilisation en intrieur afin de rduire le potentiel d'interfrences nuisibles aux systmes mobilespar satellite cocanaux. AT A GLANCE LETS GET STARTED IN THE BOX 1 Download the Vilo App Download and install the Vilo App on your phone. Vilo 6 Mesh Wi-Fi System x1 (or x2) Power Adapter x1 (or x2) Ethernet Cable x1 Quick Start Guide x1 Mesh Button Indicator Light Vilo 6 Mesh Wi-Fi System Quick Start Guide LAN Port WAN/LAN Port Front Back Reset LAN Port Power 2 Add your rst Vilo Follow the on-screen instructions in the app to add your rst Vilo and set up your Wi-Fi network. Vilo
+ Add Router Reset Long press to restore to factory settings. LAN Port Used to connect wired devices. WAN/LAN Port On main router: as WAN port, used to connect to modem. On sub router: as LAN port, used to connect wired devices. 3 Add additional Vilos Add additional Vilos by tapping the + sign in the Vilo App and following the on-screen instructions. Repeat this process until all your Vilos are connected. NEED HELP?
Vilo Vilo_zww5
Check out our Support page:
https://www.viloliving.com/support STAY CONNECTED
@viloliving
@viloliving Montserrat light Vilo6 Mesh Wi-Fi System CMYK 60*100mm 105g 2021.10.26 V1.0
:VL6WF02
:VL6WF02-
KSZP01 V2.0
UPC: