FCC ID: 2AQPF-12998 Scout (Bike Alarm & Finder)

CONTENTS WHATS IN THE BOX ENABLE PAIRING SET-UP KNOG APP CONNECT DEVICE ARMING & DISARMING SCOUT CONNECTING TO Find My CHARGING DISABLE FindMy FACTORY RESET SERIAL NUMBER LOOK-UP 6 - 7 8 - 10 3 4 5 11 12 13 14 15 BIKE ALARM AND FINDER QUICK START GUIDE KNOG.COM WHATS IN THE BOX ENABLE PAIRING Before you can pair the scout to your phone, connect the Scout to a USB charger with a standard USB-C charging cable. SCOUT ALARM AND FINDER

*Factory reset the device if it has been previously paired. See page 14 for instructions on how to factory reset your scout device. SILICONE COVER SECURITY TOOL 2 x M5 SECURITY BOLTS 2 x SPACER WASHERS P.3 P.4 SET-UP KNOG APP REGISTER DEVICE 1. Find and install the Knog 2. Enter your information to 3. Make sure your Scout is 4. Select device to add Knog app from the app store create your profile powered, charged and in Scout range. Click on the + button to search for the scout. P.5 P.6 DEVICE CONNECTED ARMING + DISARMING FROM PHONE 5. Choose a name for your 6. Knog Scout Connected 1. To arm Scout make sure the 2. The Button will now show Scout phone is in range. The Scout the Scout is Armed. should show connected. To disarm, ensure the scout is Click the black button on in range, and press the red screen to arm the Scout button on screen P.7 P.8 ARMING FROM SCOUT DISARMING FROM SCOUT 1. To arm Scout make sure the The button on the phone will 1. To disarm Scout make sure 2. Click and hold the button phone is in range and the be yellow whilst arming. the phone is in range and the on the Scout to disarm it. Knog app is active on the phone. Knog app is active on the phone. 2. Click the button on the Scout to arm it. The Scout LEDs will now flash until it is armed. Note: Scout cannot be armed unless phone is in very close range. P.9 Note: Scout cannot be disarmed unless phone is in very close range. P.10 CONNECTING FIND MY CHARGING 1. Open the Find My app by 2. Press Add New Item 1. Open USB door seal pressing the red arrow button 3. Select Add Other Item at the bottom of the screen*

4. When Scout appears, press

*To use the Apple Find My app to locate this item, the latest version of iOS, iPadOS, watchOS, or macOS is recommended. to connect to Find My. Select and name your Scout 2. Plug in USB-C cable to Charge. The charging indicator will be red while charging, and green when charging is complete. CHARGING CHARGE COMPLETE P.11 P.12 DISABLE Find My FACTORY RESET 1. Turn the Scout upside down and place on an horizontal 1. Turn the Scout upside down and place on an horizontal surface (such as a table). surface (such as a table). 2. Press and hold the button for 30 seconds until 4 short 2. Press and hold the button, while plugging in a USB-C cable. beeps are heard. Continue to hold the button for 10 seconds, until 4 short beeps This procedure will stop sharing the location of the Scout. are heard. HOLD 30 SECONDS INSERT USB-C &

CONTINUE TO HOLD BUTTON FOR 10 SECONDS P.13 P.14 SERIAL NUMBER LOOK-UP The Apple Find My app can be used to lookup the serial number of an unknown scout in your possession. 1. In the Find My app, select 2. Select the item from a list Identify found item, when the of nearby items, then press unknown Scout is nearby. continue. 3. When the following page is 4. A page similar to this displayed, press the button should be displayed with the on the Scout, then select Scout serial number. If the Continue On Website device has been set to lost mode, a message and contact details from the owner may also be displayed here. UPD ATE P.15 P.16 KNOG.COM Use of the Works with Apple badge means that a product has been designed to work specifically with the technology identified in the badge and has been certified by the product manufacturer to meet Apple Find My network product specifications and requirements. Apple is not responsible for the operation of this device or use of this product or its compliance with safety and regulatory standards. FCC WARNING Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

-- Reorient or relocate the receiving antenna.

-- Increase the separation between the equipment and receiver.

-- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

-- Consult the dealer or an experienced radio/TV technician for help. The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction. FCC COMPLIANCE STATEMENT This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC ID: 2AQPF-12998 xxxxxxxxxxxx Complies with IMDA Standards

(DBXXXXXX) XXX-XXXXXX XXX-XXXXX-XXXXX XXXXXXXXXXXXXXXX Type Approved No.: ESD-XXXXXXX TRA REGISTERED NO.: XXXXXXX/XX DEALER NO.: XXXXXXX/XX

C5266091_X10_Ed.1 Knog PTY LTD. Office of Engineering Technology Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 Subject: Request for Confidentiality FCC ID: 2AQPF-12998 Date: 6/22/2022 To Whom It May Concern, Pursuant to the provisions of Sections 0.457 and 0.459 of Commission's rules

(47CFR0.457, 0.459), we are requesting the Commission to withhold the following attachment(s) as confidential document from public disclosure. Exhibits ID Label/Location Attestation Statement External Photos Block Diagram Schematics Test Report Test Setup Photos Users Manual Internal Photos Parts List / Tune Up RF Exposure Info Operational Description Cover Letter(s) SDR Software / Security Info Long-Term Confidentiality No No No No No No Short-Term Confidentiality No No No No No Above mentioned document contains detailed system and equipment description are considered as proprietary information in operation of the equipment. The public disclosure of above documents might be harmful to our company and would give competitor an unfair advantage in the market. It is our understanding that all measurement test reports, FCC ID label format and correspondent during certification review process cannot be granted as confidential documents and those information will be available for public review once the grant of equipment authorization is issued. Sincerely, Signature:

Name: Terry Tao Date: 6/22/2022 Title:

1/1

C5266091_X8_Ed.1 Letter of Authorization Company: Knog PTY LTD. Address: 453 Church Street, Richmond VIC 3121, Victoria, Australia Product Name: Scout (Bike Alarm & Finder) Model Number: 12998, 9328389030779 FCC Identifier: 2AQPF-12998 We authorize LGAI Technological Center S.A., Ronda de la Font del Carme, s/n, 08193 Bellaterra, Spain, to act on our behalf on all matters concerning the above named equipment. Any individual within LGAI Technological Center S.A. is authorized to act on our behalf and take action on the application. We declare that authorize LGAI Technological Center S.A., Ronda de la Font del Carme, s/n, 08193 Bellaterra, Spain, is allowed to forward all information related to the approval project to the Federal Communication Commission and to discuss any issues concerning the approval application. Any and all acts carried out by LGAI Technological Center S.A. on our behalf shall have the same effect as acts of our own. Name: Terry Tao Date: 6/22/2022 Title:

Signature of applicant:

1/1

Knog PTY LTD. Model difference statement Product Name: Scout (Bike Alarm & Finder) Model No.: 12998, 9328389030779 We (Knog PTY LTD. 453 Church Street, Richmond VIC 3121, Victoria, Australia) hereby state that all the models are the same circuit and RF module, except the model name. Signature:

Name: Terry Tao Title:

Tel: +61 3 9428 6352 Email: terry@knog.com.au Date: 6.22.2022