Ko P270?P0 KR-SO2F ADVANCED HIGH SPEED RESPONSE FM RECEIVER Instruction Manual Thank you very much for purchasing this receiver. Read this manual carefully in obtain maximum performance from this unit. Notes on Handling For Safety reasons, handle with care. This sign is indicated; A possibility of death or serious injury may occur, and physical damage by accident occurs with high probability.
@This unit manufactured and sold for surface radio control models only.* Do not use for any other purpose. @Be sure that the frequency band is available before switching on the transmitter. * Other people's using the same frequency will run out of control. @Do not use this in thunderstorms. * There is possibility of lightning striking the antenna.
@Do not use the transmitter in the rain or in location where water might get on it. * The unit may become wet and cause loss of control. @Do not run the model when you experience difficulties in concentration through tiredness, alcohol or medication. * Any error of judgment may result in an accident. @Be sure to keep the transmitter, batteries and model stored out of reach of children. * There is danger of positioning by intake by mistake, burn, or an injury. @Do not disintegrate. * There is a danger of short-circuit etc. Our service department may decline the registration of repair. @Be sure to use genuine KO PROPO Crystal. * Since there is a possibility of frequency shifting, causing a defect of operation and leading to serious trouble if the product of other company is used, please do not use it by-any means. @ Do not switch the receiver on before the transmitter. There is a danger of motor and engine operating on full throttle. Be sure to turn on the switch on the transmitter first, followed by the receiver. @ Please turn off the receiver switch first, followed by the transmitter. @ This receiver is manufactured to be used in conjunction with KO PROPO Products. We cannot assume any responsibility for the use of other companies products with this unit. This sign is indicated; A possibility of injury or the physical damage accident is assumed. PALAU aT (en!
@Be sure to use genuine KO PROPO Products, transmitter, servo, and other option parts. * We cannot assume any responsibility for the use of other companies products with this unit.@Do not install other connector or old type connector. It may result in miss-operation or damage the unit.@When installed in an electric powered car, make sure that the unit is installed correctly. Incorrect positioning may affect the units performance and may be the cause of trouble. Please ensure that the wires are positioned correctly. * Please see the diagram for correct installation. @When installed in a gasoline-powered car, Please do not allow exhaust gasses, oil, and fuel to come in direct contact with the receiver, Should this unit come in contact with water or oil, remove the water or oil immediately, Please contact our service department for repair. Due to the nature of a radio control model, as a result of accident damage by the customer, our company may be unable to take responsibility. NOTE: The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment.Such modifications could void the user's authority to operate the equipment. This device complies with part 15 of the FCC Rules.Operation is subject to the following two conditions: (1) This device may not cause harmful interference,and (2) this device must accept any interference received, including interference that may cause undesired operation. Name of Parts echnical specification Antenna wire = Crystal socket @Reception system: FM-PPM system @Function : Advanced High Speed Do not bundle the antenna Be sure to use only @Number of channels : 3 channels ; __ Response wire with other cords. KO PROPO FM @Supply voltage : 35 to 65 V @Dimensions : 295 x 245 x 165 mm type crystal. @ Antenna length : 350 mm (excluding protrusions) Battery Channel When used in a Gasoline-
powered car, connect ;
@ Weight : 12.0 g (excluding crystal) Throttle Channel 2 Connect the Electronic or other noise sources
@FET servo blue wire (72V wire) or the receiver power supply. gs speed controller or Steering Channel 1 Nx l / / the throttle servo. Connect the steering servo. AUX Channel 3 i ha m ive, 5 switches can also generate
@ Mounting the Receiver Electric-powered car noise, position them as far away as When fixing the receiver in place on the chassis or on the "mechanical deck", use two pieces of possible double-sided tape, one on top of the other, so that the receiver is cushioned somewhat, Be sure that the crystal is on the high side when installing the receiver on the chassis or the "mechanical deck", The noise is conducted by them, especially a carbon product, If a receiver is not stuck, it will become strong noise. r a 0 _}5xX Oo a __+ U + ____ Do not mount the =m Use two layers of Do not position the Always position the directly on the chassis double-sided tape. crystals on the or "mechanical deck". bottom. ie antenna The silicone wire must not pass directly over the receiver. Do not allow the silicone wires to cross the antenna. crystal on the top.
= Do not position the antenna opening or
| the crystal near the batteries, motor, or the carbon chassis. Do not route the wires near the antenna.
@ Notes on Installing the Receiver Gasoline-powered car Do not secure the receiver on the chassis or the "mechanical deck". Vibrations will cause the receiver to malfunction and may even cause internal damage to the receiver. Either uses the bracket (receiver holder), provided with the kit, or else cushion the receiver with a sponge like material. Please avoid installing the receiver where exhaust gasses come into direct contact with Do not position th the unit. Invasion of an exhaust gas will result in irreparable damage. Avoid installing near engine Ono: postiuon the:
or muffler where heat may cause damage for the case, malfunctioning will occur. receiver or the antenna on the top of the motor or the batteries an ) When mounting the receiver and antenna on So = r= the "upper deck", position QV KA / SZ
. AM CD (lel) them as far away from the Notes on Antenna Installation MYO hattecles and shotor as possible The antenna pipe of the product made of plastic is used as possible use the plastic product, when 7 you mount indispensably. Do not use the antenna of the metal is easy to conduct. It may cause Service some dangerous situations. When using on FRP or carbon hollow antenna on a racing car, etc, All KO PROPO Products have been carefully inspected prior to do not pass the antenna wire through the pipe, allow it to trail away loosely outside. operating, However, if you have any problems while using it under normal conditions or the set has any detects, it will be repaired in Piano wire Pipe Plastic holder accordance with warranty conditions. When requesting service, a a Metal, carb sue war neions, . Aluminum holder ff Aluminum Cal, Caron FENN Pott the time-required repair. not use piano wire for metal, + Once again refer to this instruction manual for further checking. Metal, carbon A holder Do not cut the antenna wire, @f you feel the unit is still not functioning correctly...
(OK if FRP o % If the problem still exists, please contact our Service Dept. When carbon chassis, it may result or plastic) | Metal, carbon . as using our Service Dept., please provide details of the following OK if FRP in dangerous situations. information available under the situation, Sata ce Do not t Name of Tx, Rx, Servo, Electric Speed Controller, Motor, Batteri lug board or plastic) }o not secure antenna lame of Tx, Rx, Servo, Electric Speed Controller, Motor, Batteries, to lug wire to the plate Chassis, A use situation, the failure, condition when trouble occurred Your name, address or phone and fax number that we can contact you on. CORO Installing @Please send the Information described above when requesting repair. The crystal direction facing front or down, the crystal may fall out by the shock Kondo Kagaku Co., Ltd. Service dept. of a crash or vibration Please use crystal fixing on the case with tapes. - =
7 For more information Phone:03-3807-7751 FA X:03-3807-8155 0 Business hours: Monday through Friday except for Saturday, Sunday u% OD = O ae Y _ Tape and Japanese National holiday cS i pe ne wcivance eS pe he atyance Cos 417-7, Higashi-Nippori, Arakawa-Ku, Tokyo, 116-0014, Japan Web site: www.kopropo.co,jp