Multi controller /Multi receiver
/
MC-8/MR-8(
MC-8(Transmitter) / MR-8(Receiver) Series Thank you for purchasing radio system "MC-8/MR-8 series). MC-8/MR-8 MC-8/MR-8 RC MC-8/MR-8 are multi controller /Multi receiver for radio controlled easily RC car or original robot .
/ AH 8 This is radio controlled with assigned servo motor or motor driver to 8 channels of A to H channel. Instruction Manual For Safe Operation Due to the nature of radio controlled models, improper handling may lead to dangerous situations. Therefore please read the following information carefully in order to ensure safe operation. Please also understand that KO Propo is not responsible for any injuries or damage which result from noncompliance of these cautions and notices. Improper handling/usage may lead to a high probability of material damage as well as a possibility of serious personal injury or even death. Warning Improper handling/usage may lead to personal injury or material damage. Caution When Installing Components Make sure metal parts on the model (car chassis/ship hull) do not come into contact with each other. malfunction and lead to an uncontrollable model. Do not cut or bundle the antenna cable.
* This may lower the receiver's sensitivity and lead to an uncontrollable model.
* Contact between metal parts may result in noise, which could cause the receiver to
* Contact between metal parts may result in noise, which could cause the receiver to Ensure correct polarity when installing transmitter and receiver batteries.
* Incorrect polarity may damage the product. Make sure metal parts on the model (car chassis/ship hull) do not come into contact with each other. malfunction and lead to an uncontrollable model. Do not cut or bundle the antenna cable.
* This may lower the receiver's sensitivity and lead to an uncontrollable model. Ensure correct polarity when installing transmitter and receiver batteries.
* Incorrect polarity may damage the product. Notes for Usage Warning Prohibited matters Do not use when there is thunder.
* It is possible for lightning to strike the antenna. Do not use in the rain or in areas where water has accumulated.
* If water enters the product it may lead to an uncontrollable model. Do not use in the following locations:
Do not use when your concentration levels are compromised by tiredness, alcohol, 1. 3km 2. 3. 1. Near R/C circuits (within 3km) 2. Near crowds, on streets, or near actual vehicles or ships. 3. Near high-voltage power lines or communication facilities.
* If signal interference, etc. causes an uncontrollable model, a serious
* Mistakes in judgment may result in serious accidents. Do not allow glow engine fuel or engine exhaust to contact the product.
* These may attack the plastic and damage the produc accident may result. Check to ensure that the selected model memory matches the model to be controlled.
* Using an incorrect memory may lead to an uncontrollable model. Make sure to stop the engine (disconnect motor cables) before changing transmitter medication, etc. Warning Enforcement matters settings. Do not touch engine, motor, ESC, etc. immediately after use as they may be hot.
* Doing so may lead to burns. Caution Prohibited matter Follow the reverse order when switching o. When switching on, always turn on the transmitter rst, followed by the receiver.
* If the wrong order is followed, it may lead to an uncontrollable model. Dismantling or modifying the RF Module (internalized in the case of the EX-RR) is RF
* Doing so may lead to accidents such as short circuits and KO Propo Customer Service prohibited and is punishable by law. Department may not accept dismantled/modied products for repair. Caution Enforcement matters Caution Enforcement matters Do not use this product in aircraft, hospitals, or near re alarms or medical equipment.
* This may lead to malfunctions and result in serious accidents. Also, by law you must cease operation if the product aects other wireless or electrical devices. 2.4GHz transmitters must be registered with the Japan Radio Control Safety Association. 2.4GHz ( )
* The transmitter which you have purchases is already registered. Products which do not have proof of registration are illegal. Notes After Usage Warning Enforcement matters Caution Enforcement matters In the case of an R/C car, make sure to remove the battery pack after driving.
* If the car is switched on accidentally, it may lead to a re or an uncon trollable model. Keep transmitters, batteries, and models away from small children.
* Chemical agents and the items themselves may cause personal injury. Remove batteries from transmitter if it will not be used for a considerable time.
* If batteries are left in the transmitter, battery leakage may result in damage. Do not store transmitter/receiver in the following conditions:
1. Extremely hot (over 40C) or cold (below 10C) temperatures. 2. Locations in direct sunlight. 1. 4010 3. Locations with high humidity. 2. 3. 4. 4. Locations subject to vibrations. 5. 5. Locations with lots of dust.
* These conditions may cause the case to deform and damage the product. Explanation of product warranties KondoKagaku co. ltd. guarantee after-sale service and others about this product. However, please understand that it cannot guarantee about the following points on the character of 1 this product. 2 3 1) Breakage of the part by assembly. 2) Damage judged to be based on the operation after assembling. 3) When reconstruction of this product and analysis are conducted. Explanation of Licensing The company name or the brand name for each reference in the text is a registered HP trademark. Downloading the software from the attachment or from our homepage for this product and being used for the sole purpose of this product is accepted. Please do not use CD-ROM this for any other use. This product, software and the intellectual property rights are the legal rights of Kondo Kagaku Co. ltd. The act of which breaks the law, can result in penal regulations and other applicable laws in the region that the violation takes place. Contact information for repairing goods Kondo Kagaku Co., Ltd. Service department ADDRESS : 4-17-7 Higashi-Nippori, Arakawa-ku Tokyo Japan 116-0014 TEL : 03-3807-7648 (service) 9:00 -12:00 & 13:00 -17:00 Mon. Fri. Except national holidays Latest information can be accessed here Names of Parts MC-8 CH-A/B Stick CH-A/B When operated up and down, can control for servo motor and A MD-1 that connected to A channel. MD-1 When operated left and right, can control B channel. B CH-E CH-E button E ON/OFF When hard push to the stick, can control ON/OFF of E channel. CH-C/D stick CH-C/D When operated up and down, can control for servo motor and C MD-1 that connected to C channel. MD-1 When operated left and right, can control D channel. D CH-F CH-F button F ON/OFF When hard push to the stick, can control ON/OFF of F channel. CH-G/H CH-G/H button CH-G/H G/H 10 When operated left and right each button, can control G/H channel each at 10 steps. Power Switch Long push make a turn on. When make a turn off long push at least 1 sec. 1
//10 Can not use over 10pcs this radios in the same field/ring/track. If there are busy traffic, radio problem will be happen. Please do not use in such a situation. MC-8 2.4GH MC-8 is using 2.4GHz radio wave that is Citizen band for other electrical equipment are using. 10 Please understand advanced that radio problem may be happen even if there are using less than 10 situation. Servos:
PDS / RSx / BSx Series PDS / RSx / BSx Compatible models ESC ESC MD-1 / VFS-FR2 / VFS-FR2 PRO MD-1 / VFS-FR2 / VFS-FR2 PRO MR-8 LED LED ON It is light on when power on. It is slow flashing when pairing mode. MC-8 If it is blink with ring the buzzer please change the battery to new own. AH A to H channel connector MC-8 Connect servo motor and MD-1 to MD-1 connector that is wanted control. Battery connector Connect to battery TRIM-AD TRIM-A to D button TRIM-A A TRIMBD BD Operate each TRIM, can change neutral position(position of not operate stick ) in each channel. LED LED It is light on when under communi-
MC-8 cation. And it is blinks when MC-8 searching the paired transmitter. Antenna MR-8 RC Please using by vertical position as you can. SET-UP SET-UP switch It is use when pairing. Usage 1. MC-8 Insert battery to MC-8 Please loosen the 2 mm screw in the back side of MC-8 MC-8, get off battery cover. Set AAA battery by refer direction of figure. Set battery cover 4 2mm 2mm Screw 2. MR-8 Connect power to MR-8(receiver). Connect power to battery terminal. BAT
*Please notice direction of connector. 3.0V 6.6V Operation Voltage : 3.0V to 6.6V
*Please refer maximum voltage for Servo or Motor that connected, Please use under lower than maximum voltage. If you using ESC that is VFS-2FR etc for RC car , ESC supply VFS-FR2RCESC power to receiver. MR-8RCESC So, If you using ESC for RC car, do not connect power to BAT BAT. terminal in the receiver. CH-AH ESC Connect servo or ESC that controlled to CH-A-H. 4. MC-8 MC-8 Working mode setting There can 2 type working mode setting at each CH-A,B,C,D2 CH-A,B,C,D stick. Quick mode ESC You can 2 type working mode setting at CH-A,B,C,D each RC 1 stick. ESC Work immediately when operating Multi mode Stick operation has some lag, so, Servos and ESC is work ESC ROBOT with some delay from operation. 1 ESC This mode is recommended for operate multiple function by the stick as like as robot. It has lag when start operation. Work with some delay from operation. MR-8 Turn off power in MR-8(receiver). It is for protection for connecting device like Servos etc. MC-8OFFTRIM-D Turn off power in MC8, and turn on power with push-
POWER ing TRIM-D(Upper). TRIM-DLED Please wait with push on TRIM-D(Upper) , release TRIM-D TRIM-D(Upper) when light off LED. Initial Setting is quick mode. If you want to change mode, please operate from again. 3. MC-8 MR-8 MC-8 TRIM-APOWER Please turn on power at MC-8 with push on TRIM-A(upper ON TRIM-A button). If you release TRIM-A Button, Led is start blink. LED Pairing for MC-8 and MR-8.
*Pairing is Setting for make pair for can communication with transmitter and receiver. MR-8 SET-UP ON Please turn on power at MR-8 with push on SET-UP button. SET-UP MR-8 LED If release SET-UP button, MR-8 LED is once light off and light on again. 5. MC-8 MC-8 start and end. When push on Power switch over 0.5sec, MC-8 is POWER 0.5 MC-8 started. When push on Power switch over 1sec while MC-8 is POWER 1.0 available, MC-8 is exit. If no operation MC-8 while over 5 minutes, MC-8 ring MC- 5 buzzer for alarm. And not operate is continue more 5 5 minutes, MC-8 will be turn off power automatically. MC-8 6. CH-AD MC-8 CH-A - D Reverse setting CH-A,B,C,D MR-
CH-A,B,C,D are can change output signal direction to reverse (operate direction to reverse) CH-A Ex. when reverse CH-A Turn off power in MR-8(receiver). It is for protection for MR-8 connecting device like Servos etc. Hold turn on power MC-8, operate stick to up side(this is A MC-8 ON CH and C) or left side(this is B and D) as direction.
[ TRIM ]
Please hold beat the stick operation, push on TRIM (same CH direction button for stick). Please hold beat the stick operation,
[ TRIM]
push on TRIM (same direction button for stick). Ring the 1 buzzer like a blip when push the TRIM. And if Hold pushing TRIM, Ring like a blip after about 1 sec later again. Please check the work the TRIM by turn on power MR-8. MR-8 ON This use when steering operation direction is wrong etc. * Please setting only channel that CH needed change. Please hold beat the stick opera-
A D CH TRIM tion, long push on TRIM (same direction of button TRIM as stick). it is same operation method in the A -D each ch. 7. CH-AD MC-8 Trim setting at the CH A-D. CH-A,B,C,D CH Neutral position( operation center position) are can be
(
setting in the CH-A,B,C and D. CH-C MC-8 ON CH Push trim button of same direction as want to change when CH TRIM MC-8 is working by turn on power. Please adjust setting value by each models. ON Turn on power with push on 8. MC-8 End point setting at the CH-AD CH A-D. CH-A,B,C,D MR-
Maximum operation range(angle) are can be setting in the CH-A,B,C and D. Ex, when change operation range of right direc-
CH-C tion by CH-C. MC-8 ON ch Operate stick to the want change range direction when MC-8 is working by turn on power. CH Please hold stick TRIM operation and operate trim button for change value. Please adjust setting value by each models. It is can be change setting for adjust when if tire is touch the chassis of car when maximum opera-
tion of stick. CH
* Please setting only channel that needed change. A D CH TRIM It is same operation method in the each CH A-D. 9. MC-8 Reset operation method of MC-8 (Initialize) Can be reset MC-8 when you don't know setting value or situation. Turn off power in MR-8(receiver). It is for protection for MR-8 connecting device like Servos etc. Turn off MC-8. And Turn on again while pushing MC-8 OFF TRIM-A TRIM-CPOWER TRIM-A(down side) and TRIM-C(down-side). Please wait after release power Button but hold pushing TRIM-A(down side) and TRIM-C(down-side),After 1 sec later POWER TRIM-A(
LED is light off. TRIM-C 1LED Release TRIM-A(down side) and TRIM-C(down-side) after light TRIM-A( TRIM-C off LED. MC-8 is started with initialized. LED MC-8 LED Pushing button until light off LED.
*if you operate this method,All information of MC-8 except pairing are initialized. Also '4, Mode Setting' to '8,End point setting' will be initialized, Please these setting again. with Push on ON Turn on Power Please pairing once time at only first using. If pairing are done, in usually using, can communication MC8 with MR-8 by only turn on power. ON MC- MR-8 RC CH Steering neutral position is can be setting when the car is can not run the straight.
* Please setting only channel that needed change. FCC statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired operation. QR Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. https://www.kopropo.co.jp/products/view/xxxxxx