HF-mPCIe-Documentation V1.3.doc3 maxsol GmbH Birkenweg 2 D-93495 Weiding Tel.: +49(0)9977-8205 Fax: +49(0)9977-902933 Email: info@maxsol.de www.maxsol.de HF-mPCIe RFID Reader Documentation 07.04.2014 1 / 15 HF-mPCIe-Documentation V1.3.doc3 Contents 1 General description..............................................................................................................3 1.1 Supported RFID chips...................................................................................................3 1.2 Functional description...................................................................................................3 1.3 Model, Manufacturer ....................................................................................................4 1.4 Labelling ......................................................................................................................4 2 Applied standards and regulations........................................................................................5 3 Specification........................................................................................................................6 3.1 Power supply ................................................................................................................6 3.2 RFID data .....................................................................................................................6 3.3 Environmental conditions .............................................................................................7 3.4 Dimensions...................................................................................................................8 3.4.1 HF-mPCIe RFID Reader ........................................................................................8 3.4.2 Antenna_KEU........................................................................................................9 3.5 Dimensions of transponder..........................................................................................10 3.6 Connector ...................................................................................................................11 3.6.1 HF-mPCIe RFID reader .......................................................................................11 3.6.2 Antenna KEU.......................................................................................................11 3.7 Serial interface parameters..........................................................................................12 3.8 Host communication protocol .....................................................................................12 3.9 Life time .....................................................................................................................12 3.10 Design-FMEA ..........................................................................................................12 3.11 Production-FMEA ....................................................................................................12 4 Packaging ..........................................................................................................................13 4.1 Reader packaging........................................................................................................13 4.2 User manual................................................................................................................13 5 Embargoed countries .........................................................................................................13 6 Installation notes................................................................................................................13 7 Product warranty ...............................................................................................................14 8 Document revisions ...........................................................................................................15 07.04.2014 2 / 15 HF-mPCIe-Documentation V1.3.doc3 RFID Transponder 1 General description The HF-mPCIe RFID reader is a customer specific adopted RFID reader based on Pondi reader technology. It is designed for the use in an industrial-panel-pc-system. 1.1 Supported RFID chips Standard ISO 15693 Transponders are supported by the HF-mPCIe RFID reader. 1.2 Functional description At the detection process the RFID reader reads/writes the data of the transponder. The data is send via an USB comport emulation to host system. Drawing 1: Block diagram of HF-mPCIe RFID reader UMTC-Cabling Antenna Reader Power supply Status LED HF-
stage Selftest CPU V24 07.04.2014 3 / 15 HF-mPCIe-Documentation V1.3.doc3 1.3 Model, Manufacturer The HF-mPCIe RFID reader can be ordered at maxsol at the following order code:
HF-mPCIe RFID reader. The RFID antenna can be ordered at maxsol at the following order code:
RFID Antenna_KEU. Only this antenna may be used for the reader module. All other antennas are not allowed. The reader electronic unit consists of a RFID reader main board, with external antenna. The electronic unit is not assembled into a housing. The whole production of the HF-mPCIe RFID reader and the Antenna_KEU unit will be done under the responsibility of maxsol and a certified EMS partner. 1.4 Labelling On module:
Sticker is placed on shield of device On rear side of device in which this module is mounted HF RFID module Kontron Europe GmbH Model: HF-mPCIe FCC ID: 2AATH-HFMPCIE IC: 9927C-HFMPCIE Device contains HF RFID module Model: HF-mPCIe FCC ID: 2AATH-HFMPCIE IC: 9927C-HFMPCIE 07.04.2014 4 / 15 HF-mPCIe-Documentation V1.3.doc3 2 Applied standards and regulations The HF-mPCIe RFID reader is conformal to the following radio regulations and standards:
STATEMENTS FCC Part 15.19 RSS-GEN 7.1.2 This device complies with Part 15 of the FCC Rules and with Industry Canada license-
exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation Le prsent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorise aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible d'en compromettre le fonctionnement. FCC Part 15.21 Changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. 07.04.2014 5 / 15 HF-mPCIe-Documentation V1.3.doc3 nit VDC mVpp mA mA Symbol V VSS I standby I max 5 +/-10%
150
<100
<200 3 Specification 3.1 Power supply The circuitry is operates with an internally stabilized voltage for optimum and stable operation. Value Symbol Unit Value Supply voltage (at external USB connector) Max. ripple on supply voltage Current consumption, standby Max. current consumption 3.2 RFID data Value Symbol Unit Value RFID Frequency (typical) RFID Output power @ 50 Ohm termination Read distance The transponder is readable over the whole operation distance between reader antenna and the specified maximum read distance Symbol f PHF d Peak 13,56
<100 0 - 20 nit MHz mW mm 07.04.2014 6 / 15 HF-mPCIe-Documentation V1.3.doc3 Symbol TOperation TStorage
-10 - +85
-20 - +85 5 - 95 nit C C
%
3.3 Environmental conditions Value Symbol Unit Value Operation temperature range Storage temperature range Requested Relative humidity for storage and operation (not condensing) 07.04.2014 7 / 15 HF-mPCIe-Documentation V1.3.doc3 3.4 Dimensions 3.4.1 HF-mPCIe RFID Reader 07.04.2014 8 / 15 HF-mPCIe-Documentation V1.3.doc3 3.4.2 Antenna_KEU 07.04.2014 9 / 15 HF-mPCIe-Documentation V1.3.doc3 3.5 Dimensions of transponder Form and dimension t.b.d. by customer. This has impact on the reading distance. 07.04.2014 10 / 15 HF-mPCIe-Documentation V1.3.doc3 3.6 Connector Power/Communication:
3.6.1 HF-mPCIe RFID reader J2 Pin assignment:
Connector type:
J5 HF-connector Connector type:
1 2 3 4
+ 5V D-
D+
GND WR-WTB SMT Male Horizontal Shrouded Header 2.00mm WE 620104131822, 4 pol. Microwave Coaxial Connectors Pin 1 J2 J5 Microwave Coaxial Connectors J1 3.6.2 Antenna KEU J1 HF-connector Connector type:
07.04.2014 11 / 15 HF-mPCIe-Documentation V1.3.doc3 3.7 Serial interface parameters The data between the HF-mPCIe RFID reader and a host system are transmitted via a USB comport emulation. Interface parameters:
Baud rate 19.200 No of Bits 8 Stop bit 1; Parity N Handshake No hardware or software handshake 3.8 Host communication protocol The communication protocol between a host system and the HF-mPCIe RFID reader is defined in the document P2 Interface Protocol 3.9 Life time No MTBF calculation. 3.10 Design-FMEA No 3.11 Production-FMEA No 07.04.2014 12 / 15 HF-mPCIe-Documentation V1.3.doc3 4 Packaging 4.1 Reader packaging Every reader is packed into an ESD proof bag. Every antenna is packed into an ESD proof bag. 4.2 User manual One documentation is delivered to customer in paper and pdf. 5 Embargoed countries In customer responsibility. 6 Installation notes Special ESD prevention is required to assemble the HF-mPCIe RFID reader. It is recommend to use a ESD wristband when you unpack the reader and connect it to the host system. The system power has to be switched off prior to the assembly. Be aware of the following possible environmental effects when your are installing the HFmPCIe RFID reader into a device. Also the transponders might be effected by:
Nearby existing metal objects like housings, shielding and also PCB-boards with large ground plates. EMC effects from cables EMC effects from magnetic fields. Metal surface in direct vicinity of the active antenna will detune the antenna and thus have a direct influence to the operating distance. Increase the distance between the antenna and the metal layer to the possible maximum for least influence. Communication between the reader and a transponder can never pass through a metal layer. 07.04.2014 13 / 15 HF-mPCIe-Documentation V1.3.doc3 7 Product warranty maxsol provides customer assistance in various technical areas, but does not have full access to data concerning the use and applications of customer's products. Therefore, maxsol assumes no liability and is not responsible for customer applications or product or software design or performance relating to systems or applications incorporating maxsol products. maxsol assumes no liability and is not responsible for infringement of patents and/or any other intellectual or industrial property rights of third parties, which may result from assistance provided by maxsol. maxsol is not liable for infringements of patents and/or any other intellectual or industrial property rights of third parties resulting out of the usage in the customers industrial system. maxsol products are not designed, intended, authorized or warranted to be suitable for life support applications or any other life critical applications which could involve potential risk of death, personal injury or severe property or environmental damage. A critical component is a component used in a life-supporting device or system whose failure can reasonably be expected to cause the failure of that life-support device or system, or to affect its safety or effectiveness of that device or system. Life support devices or systems are intended (a) to be implanted in the human body, or (b) to support and/or maintain and sustain human life. If they fail, it is reasonable to assume that the health of the user may be endangered. The product warranty is defined by governmental law and in maxsol's General Conditions for the supply of products and services. 07.04.2014 14 / 15 HF-mPCIe-Documentation V1.3.doc3 8 Document revisions Version 1.0 1.1 1.2 1.3 Status draft Added FCC Statements Added some changes Added 1.4 Labelling Datum 27.06.2013 06.02.2014 10.02.2013 07.04.2014 07.04.2014 15 / 15