FCC ID: 2ARPVRB-UNI-4992 Origin8 2.4GHz Wireless Controller

SELECT START B A INSTRUCTION MANUAL MANUAL DE INSTRUCCIONES GUIDE DUTILISATION Controller Diagram Receiver Diagram Capture Home Turbo B Turbo A Includes Origin8 2.4 GHz Wireless Controller USB and NES receivers 3ft/1m USB to USB-C charge cable Instruction Manual SELECT START B A DPad Select Start Button B Button A USB NES Pairing Button R ZR ZL USB-C Charge Port L Micro USB

(Firmware Updates Only - Micro USB cable not included) EN Button Mappings EN Pairing Instructions A B

A B L R ZL ZR Capture Home Select Start Controller DPad NES DPad D-Input X-Input Switch DPad Left Analog DPad Button 2 Button 0 (B) Button 3 Button 1 (A) Button 7 Button 4 (LB) Button 8 Button 5 (RB) Button 6 Button 6 (LT) Button 5 Button 7 (RT) A B L R ZL ZR

Select Button 9 Start Button 10

Select Start Capture Home Minus (-) Plus (+) Connection NES Receiver USB Receiver To enable Turbo Function Flip the switch above Button A and/or B into the up position. Press and hold the designated button to experience rapid fire inputs. EN Macros & Compatibility Press and hold the button combination for 5 seconds to enable. Input Mode Description Select + Start + R Clear Pairings Removes all pairings from the controller. Start + B Input Switch Start + Left Left Analog Start + Right Right Analog Start + Up DPad Change from D-Input to X-Input, and vice versa. Changes DPad to act as Left Analog Changes DPad to act as Right Analog Changes the DPad back to default Pairing to a Receiver Connect a receiver into the consoles controller port and power it on. Once powered, the receiver will flash red slowly if unpaired. Press and hold the pairing button on the receiver for a few seconds until it flashes rapidly. Press Start on the controller to power it on and once more to pair it. Once paired, both controller and receiver will have their lights remain on. Upon your next play session, you only need to power on the controller with Start to connect to the console receiver on a powered console. Troubleshooting If you are experiencing connection issues, be sure that the controller is fully charged. To reset all connections, press and hold Start + Select + R for 5 seconds. To reset the controller, use a thin tool (unbent paperclip) and push a tiny button within the tiny hole on the back of the controller once -

this will reset the controller to factory default settings. EN Support To stay up to date with the latest news, manuals, and firmware updates, visit retro-bit.com/support. If you require additional help, e-mail info@retro-bit.com. Follow us online and stay in the conversation!

@retrobitgaming www.retro-bit.com Compatibility The NES receiver is compatible with original and most 3rd party clone consoles that utilize the same controller port. The USB receiver is compatible with Windows PC, Mac, Android, Raspberry Pi devices, MiSTer, Polymega, Nintendo Switch, and other USB-enabled devices and consoles. Retro-Bit is a registered trademark of Kool Brands, LLC. Mac is a registered trademark of Apple Inc. USB is a registered trademark of Universal Serial Bus Implementers Forum, Inc. Nintendo Switch is a trademark registered trademark of Nintendo of America Inc. All other mentioned trademarks are either trademarks or registered trademarks of their respective owners. All rights reserved. This product is not endorsed, manufactured, produced, sponsored or licensed by Apple Inc. or Nintendo of America Inc. Kool Brands, LLC. ES Asignacin de botones ES Instrucciones de conexin A B L R ZL ZR Capture Home Select Start Botn DPad NES DPad D-Input X-Input Switch DPad Left Analog DPad Button 2 Button 0 (B) Button 3 Button 1 (A) Button 7 Button 4 (LB) Button 8 Button 5 (RB) Button 6 Button 6 (LT) Button 5 Button 7 (RT) A B L R ZL ZR

Select Button 9 Start Button 10

Select Start Capture Home Minus (-) Plus (+) Conexin NES Receptor USB Receptor Para activar el Turbo Funcin Coloca el switch situado sobre los botones A y/o B en la posicin arriba. Mantenga pulsado el botn designado para experimentar entradas de disparo rpido. Conecta un receptor a la consola y encindelo. Una vez encendido, el receptor parpadear en rojo lentamente si no est conectado. Mantn pulsado el botn de emparejamiento del receptor durante unos segundos hasta que parpadee rpidamente. Pulsa Start en el mando para encenderlo y una vez ms para emparejarlo. Una vez emparejados, las luces del mando y del receptor permanecern encendidas. En tu prxima sesin de juego, slo tendrs que encender el mando con Start para conectarlo al receptor de la consola encendida. ES Macros & Compatibility ES Solucin de problemas Mantenga pulsada la combinacin durante 5 segundos para activarla. Entrada Modo Descripcin Select + Start + R Borrar emparejamientos Elimina todos los empareja-

mientos del controlador. Start + B Cambio de entrada Cambiar de entrada D a entrada X, y viceversa. Start + Izquierda Start + Derecho Analgico izquierdo Analgico derecho Start + Arriba DPad Cambia el DPad para que acte como Analgico Izquierdo Cambia el DPad para que acte como Analgico Derecho Devuelve el DPad a los valores predeterminados Compatibilidad El receptor NES es compatible con las consolas originales y la mayora de terceros que utilizan el mismo puerto de controlador. El receptor USB es compatible con Windows PC, Mac, Android, dispositivos Raspberry Pi, MiSTer, Polymega, Nintendo Switch y otros dispositivos y consolas con USB. Si tiene problemas de conexin, asegrese de que el mando est completamente cargado. Para restablecer todas las conexiones, mantn pulsado Start + Select + R durante 5 segundos. Para restablecer el mando, utiliza una herramienta fina y pulsa una vez un botn dentro del pequeo orificio de la parte posterior del mando; esto restablecer los ajustes de fbrica del mando. FR Mappage des boutons FR Instructions dappariement Bouton DPad NES DPad D-Input X-Input Switch DPad Left Analog DPad Connectez un rcepteur au port contrleur de la console et mettez-le sous tension. A B L R ZL ZR Capture Home Select Start Button 2 Button 0 (B) Button 3 Button 1 (A) Button 7 Button 4 (LB) Button 8 Button 5 (RB) Button 6 Button 6 (LT) Button 5 Button 7 (RT) A B L R ZL ZR

Select Button 9 Start Button 10

Select Start Capture Home Minus (-) Plus (+) Connexion NES Rcepteur USB Rcepteur Pour activer le Turbo Fonction Basculer linterrupteur situ au-dessus des boutons A et/ou B en position haut. Appuyez sur le bouton dsign et maintenez-le enfonc pour bnficier de tirs rapides. Une fois sous tension, le rcepteur clignote lentement en rouge sil nest pas appari. Appuyez sur le bouton dappairage du rcepteur et maintenez-le enfonc pendant quelques secondes jusqu ce quil clignote rapidement. Appuyez sur Start sur la manette pour lallumer et une fois de plus pour lappairer. Une fois apparis, les lumires du contrleur et du rcepteur restent allumes. Lors de votre prochaine session de jeu, il vous suffira dallumer la manette avec Start pour vous connecter au rcepteur de la console sur une console alimente. A B

A B

FR Macros et compatibilit FR Rsolution des problmes Si vous rencontrez des problmes de connexion, assurez-vous que le contrleur est compltement charg. Pour rinitialiser toutes les connexions, appuyez sur Start + Select + R pendant 5 secondes. Pour rinitialiser le contrleur, utilisez un outil fin

(trombone non pli) et appuyez une fois sur un petit bouton dans le petit trou au dos du contrleur - cela rinitialisera le contrleur aux paramtres dusine par dfaut. Appuyez sur la combinaison et maintenez-la enfonce pendant 5 secondes pour lactiver. Entre Mode Description Select + Start + R Des paires claires Supprime tous les apparie-

ments du contrleur. Start + B Commutateur dentre Passer de lentre D lentre X, et vice versa. Start + Gauche Start + Droite Analogique gauche Droite Analogique Modifie le DPad pour quil agisse en tant quanalogique gauche Modifie le DPad pour quil agisse en tant quanalogique droit Start + Haut DPad Ramne le DPad sa valeur par dfaut Compatibilit Le rcepteur NES est compatible avec les consoles originales et la plupart des consoles tierces qui utilisent le mme port de contrleur. Le rcepteur USB est compatible avec Windows PC, Mac, Android, les appareils Raspberry Pi, MiSTer, Polymega, Nintendo Switch et dautres appareils et consoles compatibles USB. Warning RF exposure statement This equipment complies with the FCC radiation exposure limits set forth for an uncontrolled environment. This transmitter must not be co-

located or operating in conjunction with any other antenna or transmitter. FCC Warning This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and

(2) this device must accept any interference received, including interference that may cause undesired operation. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. NOTE 2: Any changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. Frequency Range: 2410-2470MHz RF Output Power: 3.51dBm (EIRP)

Reference No.: WTX23X07155756W001 Page 1 of 10 ANNEX EXHIBIT 1 - PRODUCT LABELING Proposed FCC ID Label Format FCC ID: 2ARPVRB-UNI-4992 Specifications: The label shall be securely affixed to a permanently attached part of the device, in a location where it is visible or easily accessible to the user, and shall not be readily detachable. The label shall be sufficiently durable to remain fully legible and intact on the device in all normal conditions of use throughout the devices expected lifetime. Proposed Label Location on EUT FCC ID Label Location Waltek Testing Group (Shenzhen) Co., Ltd. Http://www.waltek.com.cn

Kool Brands, LLC. P.O. Box 41270, Reno, Nevada 89504, United States

. Date: 2023-02-12 Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 Ref: Attestation Statements Part 2.911 (d) (7) Filing SUBJECT: FCC Application for Grantee Code: 2ARPV Applicant FRN: 0027988344 Kool Brands, LLC. certifies that, as of the date of the filing of the application, we designate ourselves as the U.S. agent for service of process. Kool Brands, LLC. accepts to maintain an agent for no less than one year after the grantee has terminated all marketing and importation or the conclusion of any Commission-related proceeding involving the equipment. Designated U.S. Agent Information:

U.S. Agent FRN: 0027988344 Name: Kool Brands, LLC. Address:

1450 Vassar Street, Reno, Nevada 89502, United States Contact Person:

RON PANG Tel.: 909-839-6091 Email:

alexl@innexinc.com

Kool Brands, LLC. P.O. Box 41270, Reno, Nevada 89504, United States eee eee eee eee Date: 7/27/2023 Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 Ref: Attestation Statements Part 2.911(d) (5) (i) Filing SUBJECT: FCC Application for FCC ID: 2ARPVRB-UNI-4992 To Whom It May Concern:

Kool Brands, LLC. certifies that the equipment for which authorization is sought is not covered equipment prohibited from receiving an equipment authorization pursuant to section 2.903 of the FCC rules. Signatory

[RON PANG, VP]

Kool Brands, LLC. P.O. Box 41270, Reno, Nevada 89504, United States Date: 2023-08-14 Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 Ref: Attestation Statements Part 2.911(d) (5) (ii) Filing SUBJECT: FCC Application for FCC ID: 2ARPVRB-UNI-4992 To Whom It May Concern:

Kool Brands, LLC. Certifies that, as of the date of the filing of the application, the applicant is not identified on the Covered List (as a specifically named entity or any of its subsidiaries or affiliates) as an entity producing covered equipment.

Kool ant LLC. Date: 7/27/2023 FEDERAL COMMUNICATIONS COMMISSION AUTHORIZATION AND EVALUATION DIVISION 7435 OAKLAND MILLS ROAD COLUMBIA, MD 21046 SUBJECT: FCC Application for FCC ID: 2ARPVRB-UNI-4992 Confidentiality Request To whom it may concern, Pursuant to the provisions of the Commissions rules Title 47 Sections 0.457 and 0.459, we are requesting the Commission to withhold the following attachment(s) as confidential documents from public disclosure indefinitely. X Block Diagram CL] Tune-Up Information XJ Operational Description LJ) Security Information X] Schematics L] Software Defined Radio (SDR) Information L] Parts List The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these materials may be harmful to the applicant and provide unjustified benefits to its competitors. In additional to above mentioned documents, in order to comply with the marketing regulations in Title 47 CFR 2.803 and the importation rules in Title 47 CFR 2.1204, while ensuring that business sensitive information remains confidential until the actual marketing of newly authorized devices, we request Short Term Confidentiality of the following attachment(s);

L] External Photos [1 Test Setup Photos

[] Internal Photos LJ* User Manual CL] For 45 days, pursuant to Public Notice DA 04-1705. or C1 For 180 days pursuant to KDB 726920 D01. The applicant understands that pursuant to Section 0.457 of the Rules, disclosure of this application and all accompanying documentation will not be made before the date of the Grant for this application.

[RON PANG, VP]

Kool Brands, LLC. P.O. Box 41270, Reno, Nevada 89504, United States Date: 8/3/2023 FEDERAL COMMUNICATIONS COMMISSION AUTHORIZATION AND EVALUATION DIVISION 7435 OAKLAND MILLS ROAD COLUMBIA, MD 21046 SUBJECT: FCC Application for FCC ID: 2ARPVRB-UNI-4992 POWER OF ATTORNEY To Whom It May Concern:

We, the undersigned, hereby authorize Waltek Testing Group (Shenzhen) Co., Ltd. Jandy So on our behalf, to apply to the Federal Communications Commission on our equipment. Any and all acts carried out by Waltek Testing Group (Shenzhen) Co., Ltd. Jandy So on our behalf shall have the same effect as acts of our own. This is to advise that we are in full compliance with the Anti-Drug Abuse Act. We, Kool Brands, LLC. are not subject to a denial of federal benefits pursuant to Section 5301 of the Anti-Drug Act of 1988, 21 USC853a, and no party to the application is subject to a denial of federal benefits pursuant to that section. _Sincerely, Signatory

[RON PANG, VP]

7 _Sineerely,

Signatory

[RON PANG, VP]

Kool Brands, LLC. Date: 7/27/2023 Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 SUBJECT: FCC Application for FCC ID: 2ARPVRB-UNI-4992 To Whom It May Concern:

|, the undersigned, hereby states this equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules, and will apply the Supplier's Declaration of Conformity procedure to the class B device. | understand the following FCC requirements:

1. Devices subject to the SDoC procedure are required to be tested to show compliance with the FCC technical regulations by a recognized accredited testing laboratory. The testing laboratory must be accredited by a Commission approved accreditation body or designated under the terms of a government-

to-government Mutual Recognition Agreement (MRA). A listing of those accredited testing laboratories that have been recognized by the Commission is published on the FCC Webpage:

https://apps.fcc.gov/oetcf/eas/reports/TestFirmSearch.cfm (Select the "accredited" option to search for FCC recognized accredited test firms.) 2. Pt 2.1077 contains the list of information that must be included in the Supplier's Declaration of Conformity, which must be supplied with each product sold. The SDoC compliance info shall be included in the Users Manual or as a separate sheet. The info must contain the name, address, and phone number of the responsible pai which must be located within the United States. According to 2.909(b), the responsible party is either the Manufacturer or if the product is imported the Importer.