all | frequencies |
|
exhibits | applications |
---|---|---|---|---|
manual |
app s | submitted / available | |||||||
---|---|---|---|---|---|---|---|---|
1 |
|
Users Manual | Users Manual | 185.71 KiB | April 04 2002 | |||
1 | Block Diagram | April 04 2002 | ||||||
1 | External Photos | April 04 2002 | ||||||
1 | Internal Photos | April 04 2002 | ||||||
1 | ID Label/Location Info | April 04 2002 | ||||||
1 | Test Report | April 04 2002 | ||||||
1 | Test Report | April 04 2002 | ||||||
1 | Test Setup Photos | April 04 2002 |
1 | Users Manual | Users Manual | 185.71 KiB | April 04 2002 |
Test Report No.: GETET-E3-02-009 FCC Class B Certification APPENDIX H
: USERS MANUAL EUT Type: 17 LCD Monitor FCC ID : EVOKLT-1712A Models KLT-1712A 420-0881 REV. 00 TABLE OF CONTENTS INTRODUCTION FCC Compliance Statement i iii Safety Instructions 1 General Information Equipment Check list 2 3 Monitor Features GETTING STARTED Installation Control Buttons On-Screen Display ON-SCREEN CONTROLS Menu Descriptions REFERENCE Power Management Timing Guide Pin Assignment Specifications Troubleshooting 4 5 6 7 10 11 12 13 14 KDS USA Standard New Product Warranty KARES-KDS Advanced Replacement Express Service Program HOW TO REACH RADIUS If you have any questions or need assistance regarding your monitor, you may contact KDS directly using any of the following methods:
TECHNICAL SUPPORT Toll Free 800-283-1311 WEBSITE www.kdsusa.com I I I I I I I I I I I I I I I I I I I I I I I I I I N N N N N N N N N N N N N N N N N N N N N N N N N N T T T T T T T T T T T T T T T T T T T T T T T T T T R R R R R R R R R R R R R R R R R R R R R R R R R R O O O O O O O O O O O O O O O O O O O O O O O O O O D D D D D D D D D D D D D D D D D D D D D D D D D D U U U U U U U U U U U U U U U U U U U U U U U U U U C C C C C C C C C C C C C C C C C C C C C C C C C C T T T T T T T T T T T T T T T T T T T T T T T T T T I I I I I I I I I I I I I I I I I I I I I I I I I I O O O O O O O O O O O O O O O O O O O O O O O O O O N N N N N N N N N N N N N N N N N N N N N N N N N N FCC COMPLIANCE STATEMENT Note:
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable protection against radio frequency interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy. If not installed and used in accordance with the instructions, it may cause interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause interference to radio or television reception (this can be determined by turning this equipment off and on), the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment to an outlet on a circuit different from that to which the receiver is connected. CAUTION:
To comply within the limits for an FCC Class B computing device, always use the shielded signal cord and shielded power cord supplied with this unit. CAUTION TO THE USER:
The Federal Communications Commission warns that changes or modifications to the unit not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. If necessary, the user should contact the dealer or an experienced radio/television technician for additional suggestions. The user may find the Federal Communications Commission booklet, How to Identify and Resolve Radio-TV Interference Problems, helpful. This booklet is available from the U.S. Government Printing Office, Washington, D.C., Stock No. 004-000-00345-4. NOTICE OF COMPLIANCE WITH CANADIAN INTERFERENCE-CAUSING EQUIPMENT REGULATIONS i I I I I I I I I I I I I I I I I I I I I I I I I I I N N N N N N N N N N N N N N N N N N N N N N N N N N T T T T T T T T T T T T T T T T T T T T T T T T T T R R R R R R R R R R R R R R R R R R R R R R R R R R O O O O O O O O O O O O O O O O O O O O O O O O O O D D D D D D D D D D D D D D D D D D D D D D D D D D U U U U U U U U U U U U U U U U U U U U U U U U U U C C C C C C C C C C C C C C C C C C C C C C C C C C T T T T T T T T T T T T T T T T T T T T T T T T T T I I I I I I I I I I I I I I I I I I I I I I I I I I O O O O O O O O O O O O O O O O O O O O O O O O O O N N N N N N N N N N N N N N N N N N N N N N N N N N I I I I I I I I I I I I I I I I I I I I I I I I I I N N N N N N N N N N N N N N N N N N N N N N N N N N T T T T T T T T T T T T T T T T T T T T T T T T T T R R R R R R R R R R R R R R R R R R R R R R R R R R O O O O O O O O O O O O O O O O O O O O O O O O O O D D D D D D D D D D D D D D D D D D D D D D D D D D U U U U U U U U U U U U U U U U U U U U U U U U U U C C C C C C C C C C C C C C C C C C C C C C C C C C T T T T T T T T T T T T T T T T T T T T T T T T T T I I I I I I I I I I I I I I I I I I I I I I I I I I O O O O O O O O O O O O O O O O O O O O O O O O O O N N N N N N N N N N N N N N N N N N N N N N N N N N FCC COMPLIANCE STATEMENT SAFETY INSTRUCTIONS DDC COMPLIANCE NOTICE:
This digital apparatus does not exceed the Class B limits for radio noise emissions from digital apparatus set out in the Radio Interference Regulations of the Canadian Department of Communications. Handling Due to its fragile glass panel, this monitor must be handled with caution and not be exposed to impact or shock. Never touch the display area or rub it with a hard object or tool, as the panel is easily scratched. Cleaning The display area is sensitive to scratching. Do not use ketone-type cleaners (i.e. acetone), ethyl alcohol, toluene, ethyl acid or methyl chloride to clean the panel. Doing so may result in permanent damage. Water, IPA (Iso Prophyl Alcohol) and Hexane are safe cleaners. Do not allow oil or water to penetrate the display, this will cause staining and discoloration. Avoid getting food particles and fingerprints on the display area at all times. Storage Store the monitor in a dark place away from sunlight and ultraviolet
(UV) radiation, this may cause air bubbles to develop within the glass panel. Do not store the display in temperatures higher than 400C/1040F or humidity greater than 90%. Avoid condensation. ii iii I I I I I I I I I I I I I I I I I I I I I I I I I I N N N N N N N N N N N N N N N N N N N N N N N N N N T T T T T T T T T T T T T T T T T T T T T T T T T T R R R R R R R R R R R R R R R R R R R R R R R R R R O O O O O O O O O O O O O O O O O O O O O O O O O O D D D D D D D D D D D D D D D D D D D D D D D D D D U U U U U U U U U U U U U U U U U U U U U U U U U U C C C C C C C C C C C C C C C C C C C C C C C C C C T T T T T T T T T T T T T T T T T T T T T T T T T T I I I I I I I I I I I I I I I I I I I I I I I I I I O O O O O O O O O O O O O O O O O O O O O O O O O O N N N N N N N N N N N N N N N N N N N N N N N N N N SAFETY INSTRUCTIONS Caution 1. Do not open any covers on the monitor. No user serviceable parts are inside. 2. In an emergency, disconnect the AC power plug. 3. To avoid electrical shock, disconnect the power cord from the monitor before connecting the signal cable to the computer. 4. Keep away from liquids and flame. Do not immerse this monitor in water or any other liquid. Do not use this device in excessively hot conditions. 5. Handle the power cord with care. Do not bend the power cord excessively or place heavy objects on it. Do not use a damaged power cord, doing so can result in fire or electrical shock hazards. When disconnecting the power cord, always grasp the plug, not the cord. 6. The liquid crystals in the display panel contain several irritants. If the panel is damaged or broken, do not allow the liquid to come in contact with skin, eyes, or mouth. If you come in contact with the liquid, flush the affected area with running water for at least 15 minutes, then consult a doctor. 7. Handle this monitor with care when moving it. When lifting the monitor, support it with one hand holding the stand, and one hand holding the LCD screen. 8. Always disconnect the power cord when moving this monitor. 9. Do not lay this monitor in a horizontal position when operating. I I I I I I I I I I I I I I I I I I I I I I I I I I N N N N N N N N N N N N N N N N N N N N N N N N N N T T T T T T T T T T T T T T T T T T T T T T T T T T R R R R R R R R R R R R R R R R R R R R R R R R R R O O O O O O O O O O O O O O O O O O O O O O O O O O D D D D D D D D D D D D D D D D D D D D D D D D D D U U U U U U U U U U U U U U U U U U U U U U U U U U C C C C C C C C C C C C C C C C C C C C C C C C C C T T T T T T T T T T T T T T T T T T T T T T T T T T I I I I I I I I I I I I I I I I I I I I I I I I I I O O O O O O O O O O O O O O O O O O O O O O O O O O N N N N N N N N N N N N N N N N N N N N N N N N N N GENERAL INFORMATION Your new LCD monitor incorporates the latest state-of the art color Liquid Crystal Display (LCD) technology providing a wider viewing angle with higher contrast ratio. Your new LCD monitor has many advantages : safe from electromagnetic wave, lights, sharps and slims. This makes the monitor extremely suitable in the environment of administration, transportation system research, etc. Your new LCD monitor is designed for Analog input only. Your new LCD monitor does not emit any X-ray radiation and the magnetic emission greatly reduces the eyestrain. Moreover, our On Screen Controls on the side of the panel provide flexibility with simple controls. You can use these controls to adjust the display as you desire. Your new LCD monitor incorporates an active TFT module. It has a 1280 x 1024 pixel resolution, high contrast, wide viewing angle and colors up to 16.7M. iv 1 I I I I I I I I I I I I I I I I I I I I I I I I I I N N N N N N N N N N N N N N N N N N N N N N N N N N T T T T T T T T T T T T T T T T T T T T T T T T T T R R R R R R R R R R R R R R R R R R R R R R R R R R O O O O O O O O O O O O O O O O O O O O O O O O O O D D D D D D D D D D D D D D D D D D D D D D D D D D U U U U U U U U U U U U U U U U U U U U U U U U U U C C C C C C C C C C C C C C C C C C C C C C C C C C T T T T T T T T T T T T T T T T T T T T T T T T T T I I I I I I I I I I I I I I I I I I I I I I I I I I O O O O O O O O O O O O O O O O O O O O O O O O O O N N N N N N N N N N N N N N N N N N N N N N N N N N EQUIPMENT CHECK LIST MONITOR FEATURES Before operating your display, please check to make sure that all of the items listed are present in your package:
* Supports Analog IBM compatible PC, Apple MacintoshTM (Adapter optional)
* Supports DPMS for monitor power management 1) Color TFT LCD Monitor (With 15-pin D-SUB cable)
* Support DDC2B I I I I I I I I I I I I I I I I I I I I I I I I I I N N N N N N N N N N N N N N N N N N N N N N N N N N T T T T T T T T T T T T T T T T T T T T T T T T T T R R R R R R R R R R R R R R R R R R R R R R R R R R O O O O O O O O O O O O O O O O O O O O O O O O O O D D D D D D D D D D D D D D D D D D D D D D D D D D U U U U U U U U U U U U U U U U U U U U U U U U U U C C C C C C C C C C C C C C C C C C C C C C C C C C T T T T T T T T T T T T T T T T T T T T T T T T T T I I I I I I I I I I I I I I I I I I I I I I I I I I O O O O O O O O O O O O O O O O O O O O O O O O O O N N N N N N N N N N N N N N N N N N N N N N N N N N 2) Power Card 3) Manual Power Requirements The monitor is equipped with an auto-sensing power supply for voltage ranging from 100-120VAC/200-240VAC, 50/60Hz. Confirm the power rating of the AC Source before you plug the AC cable to the wall outlet.
* On Screen Control : Auto-Tune, Contrast, Brightness, H/V Position, H-
Size, Phase, Auto-Level, Color Control, OSD Position, OSD Time-out, Power Save Delay, Language, Information.
* Built-in color active matrix TFT (Thin Film Transistor) Liquid Crystal Display (LCD) that uses amorphous silicon TFTs as a switching device.
* Resolution : up to 1280 x 1024
* Color : 16.7M Color support.
* Dot pitch : 0.297mm(H) x 0.297mm(W)
* Scanning frequency : 30kHz~80kHz(H), 55Hz ~ 75Hz(V).
* Universal power supply : AC 100 - 240V allowed.
* Power consumption Normal : 40 Watt Max. Off : 5 Watt Max.
* Outside dimension : 413mm(W) x 417.5mm(H) x 182.9mm(D) 16.3"(W) x 16.4"(H) x 7.2"(D)
* Weight (net) : 5.3kg (11.7 lbs.) 2 3 INSTALLATION CONTROL BUTTONS G G G G G G G G G G G G G G G G G G G G G G G G G G E E E E E E E E E E E E E E E E E E E E E E E E E E T T T T T T T T T T T T T T T T T T T T T T T T T T T T T T T T T T T T T T T T T T T T T T T T T T T T I I I I I I I I I I I I I I I I I I I I I I I I I I N N N N N N N N N N N N N N N N N N N N N N N N N N G G G G G G G G G G G G G G G G G G G G G G G G G G S S S S S S S S S S S S S S S S S S S S S S S S S S T T T T T T T T T T T T T T T T T T T T T T T T T T A A A A A A A A A A A A A A A A A A A A A A A A A A R R R R R R R R R R R R R R R R R R R R R R R R R R T T T T T T T T T T T T T T T T T T T T T T T T T T E E E E E E E E E E E E E E E E E E E E E E E E E E D D D D D D D D D D D D D D D D D D D D D D D D D D Follow these steps to install the monitor 1. Before you connect the cables, make sure the monitor and system unit power switches are OFF. 2. Plug one end of the 15-pin signal cable to the rear of your system. The adapter may be required for certain Apple Macintosh computers. Tighten the two screws on the cable connector. 3. Connect the power cord to the inlet socket which is located at the rear of the display. Connect the plug into an AC wall outlet. G G G G G G G G G G G G G G G G G G G G G G G G G G E E E E E E E E E E E E E E E E E E E E E E E E E E T T T T T T T T T T T T T T T T T T T T T T T T T T T T T T T T T T T T T T T T T T T T T T T T T T T T I I I I I I I I I I I I I I I I I I I I I I I I I I N N N N N N N N N N N N N N N N N N N N N N N N N N G G G G G G G G G G G G G G G G G G G G G G G G G G S S S S S S S S S S S S S S S S S S S S S S S S S S T T T T T T T T T T T T T T T T T T T T T T T T T T A A A A A A A A A A A A A A A A A A A A A A A A A A R R R R R R R R R R R R R R R R R R R R R R R R R R T T T T T T T T T T T T T T T T T T T T T T T T T T E E E E E E E E E E E E E E E E E E E E E E E E E E D D D D D D D D D D D D D D D D D D D D D D D D D D AUTO AUTO AUTO AUTO R Button Description :
OSD SWITCH POWER SWITCH R R R 1. 2. 3. 4.
: Display On Screen Control menu. Select Control menu.
: Move selected icon up to select one of the controls. Increase the control value.
: Move selected icon down to select one of the controls. Decrease the control value.
: Exits the On Screen Control. Do Auto In Progress function. (Press and hold this button for two seconds.)
(fig. 1) 4 5 ON-SCREEN DISPLAY AUTO MENU DESCRIPTIONS G G G G G G G G G G G G G G G G G G G G G G G G G G E E E E E E E E E E E E E E E E E E E E E E E E E E T T T T T T T T T T T T T T T T T T T T T T T T T T T T T T T T T T T T T T T T T T T T T T T T T T T T I I I I I I I I I I I I I I I I I I I I I I I I I I N N N N N N N N N N N N N N N N N N N N N N N N N N G G G G G G G G G G G G G G G G G G G G G G G G G G S S S S S S S S S S S S S S S S S S S S S S S S S S T T T T T T T T T T T T T T T T T T T T T T T T T T A A A A A A A A A A A A A A A A A A A A A A A A A A R R R R R R R R R R R R R R R R R R R R R R R R R R T T T T T T T T T T T T T T T T T T T T T T T T T T E E E E E E E E E E E E E E E E E E E E E E E E E E D D D D D D D D D D D D D D D D D D D D D D D D D D This LCD monitor features an On-Screen Display (OSD) menu. These icons are designed to make your monitor display settings easier to control. When highlighted, the icons illustrate the control function to assist you in identifying which control needs adjustment. R AUTO Before activating the OSD menu, the button can be used to automatically adjust the display to the proper size and horizontal and R vertical position. (Press button for 2 seconds.) AUTO AUTO AUTO AUTO R AUTO AUTO The OSD menu activates automatically when you press the Enter button on the rear of the monitor. The OSD remains centered on the screen button to move while you make your adjustments. Use either the the highlight to your selection. submenu or control with a status bar will appear. The status bar indicates the direction which adjustments are being made. Use the button to adjust the control. or or AUTO R R R R The contrast and brightness menu can also be adjusted by simply R R R pressing either the or buttons. When you have finished making adjustments, press the button to save setting and exit back to main menu. ON SCREEN CONTROL AUTO C O N T R A S T ON SCREEN CONTROL AUTO C O N T R A S T S E L E C T E N T E R OSD 1 2 8 0 1 0 2 4 H F: 6 4 . 0 k H z V F: 6 0 H z P r e s s T o E x i t A Main Menu 7 6 %
OSD A D J U S T A R E T U R N O O O O O O O O O O O O O O O O O O O O O O O O O O N N N N N N N N N N N N N N N N N N N N N N N N N N
S S S S S S S S S S S S S S S S S S S S S S S S S S C C C C C C C C C C C C C C C C C C C C C C C C C C R R R R R R R R R R R R R R R R R R R R R R R R R R E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E N N N N N N N N N N N N N N N N N N N N N N N N N N C C C C C C C C C C C C C C C C C C C C C C C C C C O O O O O O O O O O O O O O O O O O O O O O O O O O N N N N N N N N N N N N N N N N N N N N N N N N N N T T T T T T T T T T T T T T T T T T T T T T T T T T R R R R R R R R R R R R R R R R R R R R R R R R R R O O O O O O O O O O O O O O O O O O O O O O O O O O L L L L L L L L L L L L L L L L L L L L L L L L L L S S S S S S S S S S S S S S S S S S S S S S S S S S AUTO-TUNE AUTO AUTO AUTO This control will automatically make adjustments to the horizontal and vertical size, horizontal and vertical position and phase. CONTRAST AUTO This control allows you to make adjustments to the contrast of the display screen. AUTO AUTO AUTO AUTO BRIGHTNESS Selecting this control allows you to make adjustments to the luminosity level of the display screen. AUTO AUTO R R H-POSITION(HORIZONTAL POSITION) and R Select this control and then use the horizontally on the screen. AUTO AUTO R R V-POSITION(VERTICAL POSITION) R R Select this control and then use the vertically on the screen. buttons to center the image R R R and buttons to center the image 6 7 H-SIZE (HORIZONTAL SIZE) R R Select this control and then use the decrease the image width to horizontally fill the display screen. and buttons to expand or AUTO AUTO POWER SAVE DELAY R AUTO AUTO This feature directs the monitor to stay in the on mode even after the computer goes into sleep mode. The user is able to select time of 5 seconds, 1 minute, 60 minutes, or OFF for the display to appear on the monitor screen. R R LANGUAGE R R Select this control and then use the buttons to choose from English(ENGLISH), German(DEUTSCH), Spanish(ESPAOL), Italian(ITALIANO), French(FRANAIS), Japanese. INFORMATION and Select this control and it will allows you to confirm information of the display.
*Note:
You can get the best quality of the image under full-screen with your computer on. The function of AUTO-TUNE may not work properly if background color is dark or if the input image does not fill the screen. (ex: DOS text mode) O O O O O O O O O O O O O O O O O O O O O O O O O O N N N N N N N N N N N N N N N N N N N N N N N N N N
S S S S S S S S S S S S S S S S S S S S S S S S S S C C C C C C C C C C C C C C C C C C C C C C C C C C R R R R R R R R R R R R R R R R R R R R R R R R R R E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E N N N N N N N N N N N N N N N N N N N N N N N N N N C C C C C C C C C C C C C C C C C C C C C C C C C C O O O O O O O O O O O O O O O O O O O O O O O O O O N N N N N N N N N N N N N N N N N N N N N N N N N N T T T T T T T T T T T T T T T T T T T T T T T T T T R R R R R R R R R R R R R R R R R R R R R R R R R R O O O O O O O O O O O O O O O O O O O O O O O O O O L L L L L L L L L L L L L L L L L L L L L L L L L L S S S S S S S S S S S S S S S S S S S S S S S S S S We strongly recommend that you just run the AUTO-LEVEL & AUTO-TUNE function to get the best image quality when you unpack the monitor or when you install a different VGA card or use a new PC. O O O O O O O O O O O O O O O O O O O O O O O O O O N N N N N N N N N N N N N N N N N N N N N N N N N N
S S S S S S S S S S S S S S S S S S S S S S S S S S C C C C C C C C C C C C C C C C C C C C C C C C C C R R R R R R R R R R R R R R R R R R R R R R R R R R E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E N N N N N N N N N N N N N N N N N N N N N N N N N N C C C C C C C C C C C C C C C C C C C C C C C C C C O O O O O O O O O O O O O O O O O O O O O O O O O O N N N N N N N N N N N N N N N N N N N N N N N N N N T T T T T T T T T T T T T T T T T T T T T T T T T T R R R R R R R R R R R R R R R R R R R R R R R R R R O O O O O O O O O O O O O O O O O O O O O O O O O O L L L L L L L L L L L L L L L L L L L L L L L L L L S S S S S S S S S S S S S S S S S S S S S S S S S S AUTO R AUTO AUTO TROUBLESHOOTING PHASE R R and Select this control and then use the image until it looks focused, crisp and sharp. AUTO AUTO AUTO buttons to adjust the screen AUTO AUTO-LEVEL AUTO AUTO This control will automatically make adjustment to the input levels of video signal.(ex. 0.714Vp-p, 1.0Vp-p) AUTO R and buttons to scroll to the desired button to select the 9300K, 6500K, 5500K R R R COLOR CONTROL AUTO AUTO Select this control, then use the color temperature. Use the or USER for custom setting. R R-GAIN(RED) R AUTO AUTO AUTO R R R Select USER then use the menu to R(Red). Use the the display. R G-GAIN(GREEN) AUTO AUTO G AUTO AUTO R R Select USER then use the menu to G(Green). Use the the display. R B-GAIN(BLUE) AUTO AUTO R R Select USER then use the menu to B(Blue). Use the the display. OSD POSITION AUTO AUTO OSD B AUTO AUTO AUTO R R Select this control and then use the R and move the OSD menu. Use the R R and Select this control and then use the OSD menu. Use the OSD TIME-OUT R R button to scroll up and down the RGB buttons to adjust the red level of and R button to scroll up and down the RGB buttons to adjust the red level of and R button to scroll up and down the RGB buttons to adjust the red level of and R button to select the direction to buttons to move the OSD menu. button to select the duration time for the buttons to select the time. (5, 15, 30, 60 SEC) 8 9 POWER MANAGEMENT TIMING GUIDE LED INDICATOR (POWER MANAGEMENT ACTIVE) The power management feature is comprised of two stages : On or Out Of Range (Green), Off (Green blinking). In the off mode, all circuitry in the monitor is shut down, except for a low power detection circuit. This circuit allows the monitor to wake up when the mouse is moved or a key on the keyboard is pressed. Power Mode H-Sync V-Sync Normal Pulse Out Of Range Pulse Pulse Pulse Video Active Active LED Color Green Green Off Off Off R R R R R R R R R R R R R R R R R R R R R R R R R R E E E E E E E E E E E E E E E E E E E E E E E E E E F F F F F F F F F F F F F F F F F F F F F F F F F F E E E E E E E E E E E E E E E E E E E E E E E E E E R R R R R R R R R R R R R R R R R R R R R R R R R R E E E E E E E E E E E E E E E E E E E E E E E E E E N N N N N N N N N N N N N N N N N N N N N N N N N N C C C C C C C C C C C C C C C C C C C C C C C C C C E E E E E E E E E E E E E E E E E E E E E E E E E E Pulse No Pulse Blanked Green blinked per 1 second No pulse Pulse Blanked Green blinked per 1 second No pulse No pulse Blanked Green blinked per 1 second 10 The LCD is a multi-frequency display. It operates at horizontal frequencies between 30KHz ~ 80KHz and vertical frequencies between 55Hz ~ 75Hz. Because of its microprocessor-based design, it offers auto-
synchronization and auto-sizing capabilities. This monitor offers 10 pre-
programmed settings that are listed in the timing table on page 11. These preset modes cover most of the common video modes supported by popular graphics adapters. However, each adapter's implementation of these video modes may vary slightly. If you find it necessary to make minor display adjustments (for example, horizontal and vertical position), please refer to the On Screen Display section of this manual for instructions. If you would like to use one of the preset timing modes, please refer to your video card manufacturer's installation guide for instructions on how to make these changes. The video card controls the refresh rate. Most video cards provide a software utility or hardware DIP switches that allows you to change the frequency used for each resolution. Timing Table Preset VESA VGA M1 M2 M3 M4 M5 M6 M7 M8 M9 MAC M10 Resolution Frequency Horizontal Vertical Horizontal Vertical Clock
[MHz]
Polarity
(H/V) 720 640 640 800 800 1024 1024 1280 1280 832 400 480 480 600 600 768 768 1024 1024 624 31.5kHz 31.5kHz 37.5kHz 37.9kHz 46.9kHz 48.4kHz 60.0kHz 64.0kHz 80.0kHz 49.7kHz 70Hz 28.322 60Hz 25.175 75Hz 31.500 60Hz 40.000 75Hz 49.500 60Hz 65.000 75Hz 78.750 60Hz 108.000 75Hz 135.000 75Hz 57.284
Note;
* If you use a Macintosh, you may need a Mac adapter. 11 R R R R R R R R R R R R R R R R R R R R R R R R R R E E E E E E E E E E E E E E E E E E E E E E E E E E F F F F F F F F F F F F F F F F F F F F F F F F F F E E E E E E E E E E E E E E E E E E E E E E E E E E R R R R R R R R R R R R R R R R R R R R R R R R R R E E E E E E E E E E E E E E E E E E E E E E E E E E N N N N N N N N N N N N N N N N N N N N N N N N N N C C C C C C C C C C C C C C C C C C C C C C C C C C E E E E E E E E E E E E E E E E E E E E E E E E E E PIN ASSIGNMENT VGA Connector VGA CONNECTOR Pin 1 Pin 2 Pin 3 Pin 4 Pin 5 Pin 6 Pin 7 Pin 8 Pin 9 Pin 10 Pin 11 Pin 12 Pin 13 Pin 14 Pin 15 Red Green Blue No Connection Ground Red Ground Green Ground Blue Ground No Connection Ground Ground DDC SDA Horizontal Sync. Vertical Sync. DDC SCL R R R R R R R R R R R R R R R R R R R R R R R R R R E E E E E E E E E E E E E E E E E E E E E E E E E E F F F F F F F F F F F F F F F F F F F F F F F F F F E E E E E E E E E E E E E E E E E E E E E E E E E E R R R R R R R R R R R R R R R R R R R R R R R R R R E E E E E E E E E E E E E E E E E E E E E E E E E E N N N N N N N N N N N N N N N N N N N N N N N N N N C C C C C C C C C C C C C C C C C C C C C C C C C C E E E E E E E E E E E E E E E E E E E E E E E E E E Note: When resolutions are shown that are lower than the pixel count of the LCD panel, text may appear choppy or bold. This is normal for all current flat panel technologies when displaying non-native resolutions on a full screen (below than 1280 x 1024 resolution). In flat panel technologies, each dot on the screen is actually one pixel, so to expand resolutions to full screen, an interpolation of the resolution must be down. When the interpolated resolution is not an exact multiple of the native resolution, the mathematical interpolation necessary may cause some lines to appear thicker than others. SPECIFICATIONS LCD Type Color Filter Colors Glass surface Viewing Left / Right Angles Up / Down Contrast Ratio Typ. Luminance of White Typ. Compatibility PC Refresh Rate Max. 17 diagonal viewable screen TFT (Thin Film Transistor), Active Matrix Panel, 0.264mm pixel pitch R,G,B vertical stripe 16.7M Anti-glare coating 80 / 80 80 / 80 350:1 200cd/m2 IBM XT, AT, 386, 486, Pentium or PS/2 and compatibles(from VGA up to 1024 x 768 @ 75Hz NI.) 1280 x 1024 @ 75Hz NI
(60Hz for optimal display) Connectors Input Signal Power 15-pin D-SUB AC In let Socket Power Input Consumption AC 100-240V 50-60Hz 40 watts (Maximum) Display Area Max. 337.9mm(H) x 270.3mm(V) Operating Temperature Humidity Altitude 32F to 104F(0C to 40C) 20% RH to 80%RH (no condensation) To 10,000 feet Storage Temperature Conditions Humidity
-14F to 104F (-20C to 40C) 5%RH to 90%RH (no condensation) Dimension 413mm(W) x 417.5mm(H) x 182.9mm(D) 16.3(W) x 16.4(H) x 7.2(D) Weight Net 5.3Kg (11.7lbs) R R R R R R R R R R R R R R R R R R R R R R R R R R E E E E E E E E E E E E E E E E E E E E E E E E E E F F F F F F F F F F F F F F F F F F F F F F F F F F E E E E E E E E E E E E E E E E E E E E E E E E E E R R R R R R R R R R R R R R R R R R R R R R R R R R E E E E E E E E E E E E E E E E E E E E E E E E E E N N N N N N N N N N N N N N N N N N N N N N N N N N C C C C C C C C C C C C C C C C C C C C C C C C C C E E E E E E E E E E E E E E E E E E E E E E E E E E 12 13 TROUBLESHOOTING No power. Flip the power switch ON. The Power LED turns on. Make sure AC power cord is securely connected to a power outlet. Power on but no screen image. Make sure the video cable attached with this monitor is tightly secured to the video output port on the back of the computer. Adjust the brightness and contrast. R R R R R R R R R R R R R R R R R R R R R R R R R R E E E E E E E E E E E E E E E E E E E E E E E E E E F F F F F F F F F F F F F F F F F F F F F F F F F F E E E E E E E E E E E E E E E E E E E E E E E E E E R R R R R R R R R R R R R R R R R R R R R R R R R R E E E E E E E E E E E E E E E E E E E E E E E E E E N N N N N N N N N N N N N N N N N N N N N N N N N N C C C C C C C C C C C C C C C C C C C C C C C C C C E E E E E E E E E E E E E E E E E E E E E E E E E E Image is unstable, unfocused. Use AUTO-TUNE to adjust automatically. If the image is still unstable after AUTO-TUNE processing, please adjust PHASE manually to get image focused. Check whether the resolution or refresh rate in windows display setting is beyond supported range(please refer to the specification of supported mode). Flickering. Not enough power is being supplied to the LCD Monitor. Connect the LCD Monitor to a different outlet. If a surge protector is being used, there may be too many devices plugged in. See Timing Guide in this manual with a list of refresh rates and frequency settings showing the recommended setting for the LCD Monitor. Wrong or abnormal colors. If any colors (Red, Green, or Blue) are missing, check the video cable to make sure it is securely connected. Loose pins in the cable connector could cause a bad connection. Connect the LCD Monitor to another computer. Check the graphics card for proper sync scheme (or sync polarities) to match the LCD Monitors specifications. Double (split) screen image. Make sure your graphics card is set to Non-Interlaced mode. Entire screen image rolls (scrolls) vertically. Make sure the input signals are within the LCD monitors specified frequency range.
(Maximum: VESA, MAC 1280 x 1024@75Hz) Connect the video cable securely. Try the this Monitor with another power source. Control buttons do not work. Press only one button at a time. R R R R R R R R R R R R R R R R R R R R R R R R R R E E E E E E E E E E E E E E E E E E E E E E E E E E F F F F F F F F F F F F F F F F F F F F F F F F F F E E E E E E E E E E E E E E E E E E E E E E E E E E R R R R R R R R R R R R R R R R R R R R R R R R R R E E E E E E E E E E E E E E E E E E E E E E E E E E N N N N N N N N N N N N N N N N N N N N N N N N N N C C C C C C C C C C C C C C C C C C C C C C C C C C E E E E E E E E E E E E E E E E E E E E E E E E E E ABOUT THE LCD The LCD contains over 2,359,296 thin-film transistors (TFTs). A small number of missing, discolored, or lighted dots on the screen is an intrinsic characteristic of TFT LCD technology and is not an LCD defect. If you display a fixed pattern for more than 10 hours, its image may remain on the screen in overlap mode when you display something else. 14 15 MEMO MEMO
frequency | equipment class | purpose | ||
---|---|---|---|---|
1 | 2002-04-04 | JBP - Part 15 Class B Computing Device Peripheral | Original Equipment |
app s | Applicant Information | |||||
---|---|---|---|---|---|---|
1 | Effective |
2002-04-04
|
||||
1 | Applicant's complete, legal business name |
Korea Data Systems Co Ltd
|
||||
1 | FCC Registration Number (FRN) |
0005897434
|
||||
1 | Physical Address |
170 Gongdan-Don, Gumi-Si
|
||||
1 |
Gyungbuk 730-030, N/A
|
|||||
1 |
South Korea
|
|||||
app s | TCB Information | |||||
1 | TCB Application Email Address |
j******@baclcorp.com
|
||||
1 | TCB Scope |
A1: Low Power Transmitters below 1 GHz (except Spread Spectrum), Unintentional Radiators, EAS (Part 11) & Consumer ISM devices
|
||||
app s | FCC ID | |||||
1 | Grantee Code |
EVO
|
||||
1 | Equipment Product Code |
KLT-1712A
|
||||
app s | Person at the applicant's address to receive grant or for contact | |||||
1 | Name |
D**** S********
|
||||
1 | Title |
General Manager
|
||||
1 | Telephone Number |
82-54********
|
||||
1 | Fax Number |
82-54********
|
||||
1 |
d******@kds21.com
|
|||||
app s | Technical Contact | |||||
n/a | ||||||
app s | Non Technical Contact | |||||
n/a | ||||||
app s | Confidentiality (long or short term) | |||||
1 | Does this application include a request for confidentiality for any portion(s) of the data contained in this application pursuant to 47 CFR § 0.459 of the Commission Rules?: | No | ||||
1 | Long-Term Confidentiality Does this application include a request for confidentiality for any portion(s) of the data contained in this application pursuant to 47 CFR § 0.459 of the Commission Rules?: | No | ||||
if no date is supplied, the release date will be set to 45 calendar days past the date of grant. | ||||||
app s | Cognitive Radio & Software Defined Radio, Class, etc | |||||
1 | Is this application for software defined/cognitive radio authorization? | No | ||||
1 | Equipment Class | JBP - Part 15 Class B Computing Device Peripheral | ||||
1 | Description of product as it is marketed: (NOTE: This text will appear below the equipment class on the grant) | 17" LCD Monitor | ||||
1 | Related OET KnowledgeDataBase Inquiry: Is there a KDB inquiry associated with this application? | No | ||||
1 | Modular Equipment Type | Does not apply | ||||
1 | Purpose / Application is for | Original Equipment | ||||
1 | Composite Equipment: Is the equipment in this application a composite device subject to an additional equipment authorization? | No | ||||
1 | Related Equipment: Is the equipment in this application part of a system that operates with, or is marketed with, another device that requires an equipment authorization? | No | ||||
1 | Is there an equipment authorization waiver associated with this application? | No | ||||
1 | If there is an equipment authorization waiver associated with this application, has the associated waiver been approved and all information uploaded? | No | ||||
app s | Test Firm Name and Contact Information | |||||
1 | Firm Name |
Bay Area Compliance Laboratory
|
||||
1 | Name |
J******** C******
|
||||
1 | Telephone Number |
408-7********
|
||||
1 | Fax Number |
408-7********
|
||||
1 |
b******@baclcorp.com
|
|||||
Equipment Specifications | |||||||||||||||||||||||||||||||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
Line | Rule Parts | Grant Notes | Lower Frequency | Upper Frequency | Power Output | Tolerance | Emission Designator | Microprocessor Number | |||||||||||||||||||||||||||||||||
1 | 1 | 15B |
some individual PII (Personally Identifiable Information) available on the public forms may be redacted, original source may include additional details
This product uses the FCC Data API but is not endorsed or certified by the FCC