FCC ID: 2AGY2RFIDBULKSYS RFID Bulk System for Kornit Printers

RFID BULK SYSTEM MODULE January 25, 2021 Overview It features:

The module is a passive RFID reader which designed by LogiTag to use for reading passive RFID tags. The reader works at 13.56 MHz frequency. 8 x LT-HF-ANT-4060 (designed by LogiTag) antennas

- Antennas selection by Multiplexer

- Serial (RS232) interface

12 24 V input FCC Compliance Statement This device has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in residential installations. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio and television reception. However, there is no guarantee that interference will not occur in a particular installation. If this device does cause such interference, which can be verified by turning the device off and on, the user is encouraged to eliminate the interference by one or more of the following measures:

Re-orient or re-locate the receiving antenna. Increase the distance between the device and the receiver. Connect the device to an outlet on a circuit different from the one that supplies power to the receiver. Consult the dealer or an experienced radio/TV technician. WARNING! Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to two conditions:

(1) This device may not cause harmful interference, and (2) this device must accept any interference that may be received or that may cause undesired operation. Le present appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisee aux deux conditions suivantes :(1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioelectrique subi, meme si le brouillage est susceptible d'en compromettre le fonctionnement. RFID BULK SYSTEM MODULE Installation Instruction The RFID module is installed inside the host printers. The installation contains mechanical, electrical and communication connections. The module is mechanically connected to the host chassis by 2 M4 screws as shown in the drawing. Electrically, the system is connected as follows:

110/230 V 110/230V to 24V DC/DC RFID The system communicates with pc by RS232 connection. FVIN: 1.0 RFID BULK SYSTEM MODULE This model is not sold separately and is not installed in any units other than Kornit Digitals products, and currently it is used in the following hosts per FCC Grant Dated 08/29/2016 under FCC ID: 2AGy2RFIDBULKSYS. Paradigm Paradigm 2 Avalanche Avalanche 1000 Avalanche 2000 Avalanche Hexa Avalanche DC Pro Allegro Allegro 2 Vulcan Storm Storm 2 Storm 1000 Storm Hexa Storm Duo Breeze Atlas Atlas Max Presto Avalanche HD6 OEM Instructions Kornit Digital now wishes to expand the LMA to include the new host:

a. The module is limited to OEM installation ONLY. b. The OEM integrator is responsible for ensuring that the end-user has no manual instructions to remove or install the module. c. The module is limited to installation in mobile or fixed applications, according to Part 2.1091(b);

d. Separate approval is required for all other operating configurations, including portable configurations with respect to Part 2.1093 and different antenna configurations;

e. Labeling instructions of finished products must contain the following:

"Contains Transmitter Module FCC ID: 2AGY2RFIDBULKSYS, IC: 21026 RFIDBULKSYS". RFID BULK SYSTEM MODULE The OEM/Integrator must include the following instructions/statements in the host user's manual (i.e. end product):

a. Statements required per FCC Part 15.19 and 15.21;

b. End users must be provided with transmitter/antenna installation requirements and operating conditions for satisfying RF exposure compliance:

i. A separate section should clearly state "FCC RF Exposure requirements;"

ii. Required operating conditions for end users iii. Antenna/or transmitter installation requirements, where relevant (For example: whether the antenna used with this module must be installed to provide a separation distance of at least 30 cm from all persons and must not transmit simultaneously with any other antenna or transmitter.) Please refer to KDB821551 for grant conditions for various types of product.

PRESTO Contains:

FCC ID: 2AGY2RFIDBULKSYS IC:21026-RFIDBULKSYS Atlas Contains:

FCC ID: 2AGY2RFIDBULKSYS IC:21026-RFIDBULKSYS This device complies with part 15 of the FCC Rules. Operation is subject to two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference that may be received or that may cause undesired operation. This device complies with part 15 of the FCC Rules. Operation is subject to two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference that may be received or that may cause undesired operation. Atlas Max Contains:

FCC ID: 2AGY2RFIDBULKSYS IC:21026-RFIDBULKSYS Avalanche HD6 Contains:

FCC ID: 2AGY2RFIDBULKSYS IC:21026-RFIDBULKSYS This device complies with part 15 of the FCC Rules. Operation is subject to two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference that may be received or that may cause undesired operation. This device complies with part 15 of the FCC Rules. Operation is subject to two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference that may be received or that may cause undesired operation.

December 20, 2020 We hereby authorize Ilan Cohen of ITL to act on the behalf of Kornit Digital, regarding the FCC C2PC To: Timco Engineering Inc. To Whom It May Concern, process for the following application:

FCC ID: 2AGY2RFIDBULKSYS Thank you, Rea Rogel System Engineer Director Kornit Digital DocuSign Envelope ID: 4C626CBC-0C29-4776-9F16-9B00AC833181

Subject: C2PC COVER LETTER December 21, 2020 RE: C2PC request for FCC ID: 2AGY2RFIDBULKSYS To whom it may concern, 1. An FCC LMA Grant was issued on 08/29/2016 for Kornits RFID Bulk System for Kornit Host Printers. 2. The module was approved for use in the specific Kornit host digital printers 3. Kornit now wishes to expand the LMA to include the following Kornit Host listed in the Grant. printer model(s):

a. Presto b. Avalanche HD6 c. Atlas d. Atlas Max 4. In support of C2PC it will be submitting the following:

Revised LMA Letter;

Label(s) for new printer host;

User Manual listing all host printers Photo of RFID Bulk System in new host;

i. ii. iii. iv. Thank you, Rea Rogel System Engineer Director Kornit Digital DocuSign Envelope ID: 4C626CBC-0C29-4776-9F16-9B00AC833181

Ref: LMA Compliance Letter for C2PC To: Federal Communications Commission December 20, 2020 Subject: C2PC LMA compliance letter This letter introduces Kornit Digitals request for a C2PC to its original FCC certification which approved its 13.56MHz RFID module, RFID Bulk System according to FCC Limited Modular Approval procedure in certain printer hosts, and to demonstrate the means to control the module as required by the LMA procedure. The RFID Bulk System is specialty designed to be placed in Kornit Digitals printers. The systems main feature is to prevent customers from using ink other than provided by Kornit. This is achieved by placing RFID tags on ink bottles and RFID reader on the Bulk system base. This model is not sold separately and is not installed in any units other than Kornit Digitals products, and currently it is used in the following hosts per FCC Grant Dated 08/29/2016 under FCC ID: 2AGy2RFIDBULKSYS. Paradigm Paradigm 2 Avalanche Avalanche 1000 Avalanche 2000 Avalanche Hexa Avalanche DC Pro Allegro Allegro 2 Vulcan Storm Storm 2 Storm 1000 Storm Hexa Storm Duo Breeze Per above mentioned FCC Grant, Kornit Digital now wishes to expand the LMA to include the new host:

Atlas Atlas Max DocuSign Envelope ID: 093CBEAB-5F18-4893-BB0F-45EA7ECC2460 Presto Avalanche HD6 Due to all the above mentioned, Kornit Digital feels that the testing conducted by ITL to the various hosts, with the fact that Kornit Digital will have full control on the sales and installation of the module, assure complete compliance with FCC LMA procedure. As per 15.212 Modular transmitters:

Single modular transmitters must meet the following requirements to obtain a modular transmitter approval. Requirement Not Maintained Maintained No shielding V The modular transmitter has RS232 connection V V

(1) The radio elements of the modular transmitter must have their own shielding. The physical crystal and tuning capacitors may be located external to the shielded radio elements.

(2) The modular transmitter must have buffered modulation/data inputs (if such inputs are provided) to ensure that the module will comply with part 15 requirements under conditions of excessive data rates or over-modulation.

(3) The modular transmitter must have its own power supply regulation.

(4) The modular transmitter must comply with the antenna and transmission system requirements of 15.203, 15.204(b) and 15.204(c). The antenna must either be permanently attached or employ a unique antenna coupler (at all connections between the module and the antenna, including the cable). The professional installation provision of 15.203 is not applicable to modules but can apply to limited modular approvals under paragraph (b) of this section. DocuSign Envelope ID: 093CBEAB-5F18-4893-BB0F-45EA7ECC2460 As per 15.212 Modular transmitters:

Single modular transmitters must meet the following requirements to obtain a modular transmitter approval. Not Maintained Maintained V Refer to test report Requirement

(5) The modular transmitter must be tested in a stand-alone configuration, i.e. , the module must not be inside another device during testing for compliance with part 15 requirements. Unless the transmitter module will be battery powered, it must comply with the AC line conducted requirements found in 15.207. AC or DC power lines and data input/output lines connected to the module must not contain ferrites, unless they will be marketed with the module (see 15.27(a)). The length of these lines shall be the length typical of actual use or, if that length is unknown, at least 10 centimeters to insure that there is no coupling between the case of the module and supporting equipment. Any accessories, peripherals, or support equipment connected to the module during testing shall be unmodified and commercially available (see 15.31(i)).

(6) The modular transmitter must be equipped with either a permanently affixed label or must be capable of electronically displaying its FCC identification number.

(7) The modular transmitter must comply with any specific rules or operating requirements that ordinarily apply to a complete transmitter and the manufacturer must provide adequate instructions along with the module to explain any such requirements. A copy of these instructions must be included in the application for equipment authorization. V V DocuSign Envelope ID: 093CBEAB-5F18-4893-BB0F-45EA7ECC2460 As per 15.212 Modular transmitters:

Single modular transmitters must meet the following requirements to obtain a modular transmitter approval. Requirement Not Maintained Maintained V

(8) The modular transmitter must comply with any applicable RF exposure requirements in its final configuration. Thank you, ____________________ Yehuda Krasner Director of Quality and Reliability Kornit Digital DocuSign Envelope ID: 093CBEAB-5F18-4893-BB0F-45EA7ECC2460

Form 731 Signature Authorization Letter February 15, 2021 To: Timco Engineering Inc. To Whom It May Concern We hereby authorize Ilan Cohen of ITL as an authorized individual to sign for Form 731 on behalf of Kornit Digital for the FCC ID: 2AGY2RFIDBULKSYS C2PC application. Thank you, Rea Rogel Systems Engineer Director Kornit Digital DocuSign Envelope ID: 9099A02A-8B3F-4DAB-9F6B-630A83AD1505