FCC ID: H78KPRFM200U BASE STATION TRANSCEIVER

RFM200U UHF Radio Transceiver Installation Manual Web Site: www.kpsystems.com ISRAEL Office Email: info@kpsystems.com Tefen Industrial Park, Tefen 24959 Tel: 972-4-987-3066 Fax: 972-4-987-3692 USA Office:

KP ELECTRONICS INC. Email: info@kpsystems.com 415 Sargon way Suite F Horsham PA 19044 Tel: (215) 442-7460 Fax: (215) 442-7461 RFM200U General Description The RFM200U is used as RF modem which holds the RF communication between he RMR and the metering devices. The interface with the PC is done through USB Type B for data exchange and Mini Type B for parameter setting. The RFMU radio is high power 5W UHF radio covers the 430 to 471MHz RF band. The RFM200U is power from 12.5V power supply that is backed up with Lid Accid 12V battery. Connectors P.N.: Book 116 Rev: New Approved: Amir 28/12/10 Data Connector USB Type B used as data link between the RFM200U and the PC. Antenna Tx/Rx and Tx BNC connector. It is used as Tx/Rx (2 ways) antenna connection or just Tx antenna connection if the second Rx connecter is in used i.e. by special jumper in the board. Antenna Rx BNC connector. It is used for Rx antenna connection in case the other connecter is just for Tx. Sets by special jumper in the board. Power Connector. Data LED Updating Parameter Value Changes Confirming Parameter Value Changes Activating Self Test Whenever there is data on the USB cable then the LED is flickering. PTT LED CM LED Whenever the radio is on transmission this LED is on. Whenever the RFM200U senses any RF signal above -107dBm then this LED is on. Data LED Whenever the RFM200U is powered then the LED is on. Preparing for Operation The BSRU100N is not a standalone unit, this device always combined in to products like the RMR perform the following steps:

a. Connecting Assembly Cables Technical Specification General Band Frequency Range Channel Spacing Programming 1. Connect one end of the coax cable to Rx/Tx BNC. In case the Tx and the Rx signals are separated then connect the second (Rx) cable to the Rx Coax. 2. Connect the DC plug to the Power Plug Socket. 4. Connect one end of the data cable to USB rear panel connector. FCC rules and reg. under Operating Voltage Diagnostics b. Setting Communication Parameters Using KPs GUP5000 Utility Program, the RFM200U parameter values listed below can be programmed or modified. Transmit frequency (MHz) Rx frequency (MHz) Receiver Sensitivity analogy MDS sensitivity Adj. Ch. Selectivity Intermodulation response Spurious and image rejection Transmitter Nominal output power 70dB 5w UHF 430-471 MHz 12.5 KHz Fully PC programming Part 15.109 Subpart

(B) radiated spurious emissions. Part 22,90,95 10-15 VDC Tx/Rx mod, Tx timer, power trouble, LD, Low Bat, Ovrl., CM, RSSI

-116dBm @ 12 dB SINAD

-119dBm 60 dB for 12.5 KHz

>60dB Programmer Connector Mini USB type B connector. This connector is used to connect a special PC application (GUP) to set or read parameters as Tx and Rx frequencies. Operating Instructions Connecting BSRU100N to GUP5000

(utility program) Loading Parameter Values Changing Parameter Values RF EXPOSURE:

The antenna gain used with this transmitter should be 0 dBi or less and all persons should maintain a minimum safety separation distance of 35.64 cm

Federal Communications Commission Authorization and Evaluation Division Confidentiality Request regarding application for certification of FCC ID: H78KPRFM200U Pursuant to Sections 0.457 and 0.459 of the Commissions Rules, we hereby request confidential treatment of information accompanying this application as outlined below:

Schematics Block Diagram Circuit Description Tuning Procedure Parts List The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these materials may be harmful to the applicant and provide unjustified benefits to its competitors. The applicant understands that pursuant to Section 0.457 of the Rules, disclosure of this application and all accompanying documentation will not be made before the date of the Grant for this application. Pursuant to DA04-1705 June 15, 2004 of the Commissions public notice, we also request temporary confidential treatment of information accompanying this application as outlined below for a period of 180 days Sincerely, Yoram Kenig P.O.Box 42 Tefen Industrial Park 2495900 Tefen Tel: 972-4-9873066, Fax: 972-4-9873692

-E info@kpsystems.co m mail:

www.kpsystems.com P.O.Box 42 Tefen Industrial Park 2495900 Tefen Tel: 972-4-9873066, Fax: 972-4-9873692

-E info@kpsystems.co m mail:

www.kpsystems.com

Date: Mar 11, 2020 Federal Communications Commission Authorization and Evaluation Division 1435 Oakland Mills Road Columbia, MD 21046 SUBJECT: FCC Application for FCC ID: H78KPRFM200U To Whom It May Concern:

We, the undersigned, hereby attest to the fact that we will apply the Declaration of Conformity procedure to the class B computer peripheral portion of this composite filing. Note:

We understand that devices subject to the DoC procedure are required to be tested to show compliance with the FCC technical regulations by a recognized accredited testing laboratory. The testing laboratory must be accredited by a Commission approved accreditation body or designated under the terms of a government-to-

government Mutual Recognition Agreement (MRA). A listing of those accredited testing laboratories that have been recognized by the Commission is published on the FCC Webpage:

https://apps.fcc.gov/oetcf/eas/reports/TestFirmSearch.cfm Select the "accredited" option to search for FCC recognized accredited test firms. Test facilities located in countries, where the U.S. does not have an operational Telcom MRA are not recognized by the FCC to test for the DoC procedure. Sincerely, Yoram Kenig President P.O.Box 42 Tefen Industrial Park 2495900 Tefen Tel: 972-4-9873066, Fax: 972-4-9873692

-E info@kpsystems.com mail:

www.kpsystems.com

12/11/19 Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 Subject: Extended Frequencies Justification Gentlemen:

We, KP Electronic Systems, Ltd., would like to submit the following justification to show the frequency range (430-471 MHz) on the Grant of Equipment Authorization under Part 90 for our FCC ID: H78KPRFM200U Per the FCCS KDB 634817 guidance, as an alternative to listing the exact frequencies, we acknowledge that its a violation of the FCC Rules if this device operates on unauthorized frequencies. This radio is intended for use by public agencies, as well as commercial, business, and industrial services. Additionally, it will be used in other countries that accept the FCC Grant of Equipment Authorization. These services account for a majority of users as described in the below table. Frequencies MHz 430 to 454 454- 456 456 462.5375 462.5375- 462.7375 462.7375 467.5375 467.5375 467.7375 467.7375 471 90 90 90 90 Part 90 Federal ITU Region 1, 2, 3 1, 2, 3 X X X This radio complies with 47 CFR Part 90.203(e) in that the operator cannot program and transmit on frequencies, other than those programmed by the manufacturer, service or maintenance personnel, using the equipments external operation controls. Sincerely, Yoram Kenig P.O.Box 42 Tefen Industrial Park 2495900 Tefen Tel: 972-4-9873066, Fax: 972-4-9873692

-E info@kpsys tems.com mail:

www.kpsystems.com

(Must be on Company Letter Head Stationary) Date HON'W Sto Road 4s ae SUBJECT: Appliation() for Certification for FCC LD: HTSKPREMDOGU To Whom It May Concern We, the undersigned, hereby autorize Sharon Hoffinan at TIMCO ENGINEERING, INC. on our behalf, o apply for certification on our equipment referenced above. Any and all acts ctied out by TIMCO ENGINEERING, INC. on our bebal hal ave the same eos as acts of our own, This sto advise that we are in fil compliance wih he Anti-Drug Abuse Act. Wo, the applicant, ae nt subject oa dni of federal benefits pursiant to Sesion S301 ofthe An Drug Aet of 1988, 21 USC853a, and no purty tothe application is subject to a dena of fedora benefits pursuant otha section, Regards,

(ast be signed by the petson tat is listed onthe FCC Website) Winco setesye\TincoOtie\TenpnesFormsrotenboldem Testing oceans Yoram Kenig President DY WIRELESSDAIASOLUTIONS

December 11, 2019 Federal Communications Commission Authorization and Evaluation Division, 7435 Oakland Mills Road Columbia, MD 21046 USA Re: FCC ID: H78KPRFM200U Attestation Statement per 90.203(e) and (g) Sincerely, Yoram Kenig Programming of transmitter frequencies can only be performed by the manufacturer or authorized service and maintenance personnel. The radio output power is fixed and cant be changed. P.O.Box 42 Tefen Industrial Park 2495900 Tefen Tel: 972-4-9873066, Fax: 972-4-9873692

-E info@kpsystems.com mail:

www.kpsystems.com