Normal Security Set INSTALLATION MANUAL Galileo Please, read carefully the installation manual before installing it, and install it according to the manual. Please, keep the manual for a future reference. G034_EN1709_R01 Before installing, Please check up the parts. Large Maintenance kit Maintenance kit Use if the product needs to be reinstalled. a b c Small d m1 m2
Installation Guide - Galileo Normal Security Set How to assemble c
b CAUTION A.
- Cautions when attaching the double-sided tape. 1.After removing the protective film from the double-sided adhesive tape, preserve the tape so that it doesn't get dirty. If touching the tape with a hand or foreign materials get on it, its adhesive strength can be significantly deteriorated. 2.The adhesive tape will have full adhesive strength after the 24 hours from its placement. Please do not use the products right after its placement. Remove the protective film from all double-sided tapes on the bottom surface of the cradle( ). b Remove the protective film Refer to Caution A. a 1 b 2-A Insert the Charging & security cable( ) into the hole on the smart table while facing downward, and attach the cradle over the hole on the table. a 2-B Array the Charging & security cable( ) into the cable guide of the cradle properly, insert it into the hole on the table in the direction to the rear side of the cradle and attach it on the proper position firmly. a A - Installing on the smart table B - Installing on a normal table a Hole on the smart table a a Hole on the normal table a 3 Detach the part of the strap that has the strap buckle from Galileo.
Make sure to detach the correct part of the strap. 4 c Move the security sensor( ) close according to the shape of Galileo. Do not remove the sensor pin protection sheet until the security sensor has been properly connected. Removing the protecive sheet before installation may result in damage to the sensor pin. Check the strap buckle Separate here Strap
Caution Make sure to detach the correct part of the strap.
5 First, insert pin 'A' of the strap spring bar into the strap fixing groove of Galileo. Next, press pin 'B' of the strap spring bar using the Pin assembly/separation tool'( ). d
Strap
d Do not remove the sensor pin protection sheet before completing the assembly of the security sensor. c Sensor pin protection sheet
Sensor pin protection sheet 6 With the pin of the strap spring bar pressed, push the strap in the direction of the security sensor( c ) and insert it into the strap fixing groove of the Galileo. Make sure to remove the sensor pin protection sheet after manually shaking the assembled strap to see if it falls out or not. c c
Strap Sensor pin protection sheet
Make sure to remove the sensor pin protection sheet after assembling the security sensor. c 8 When mounting Galileo on the cradle head, check if the cable of the Security sensor( ) is installed correctly to direction of the rear side of the cradle as shown in the figure below. If the Security sensor is installed in the wrong direction, install it again by checking the assembling direction in of the installation guide. 3 c Cable direction Cable direction 7 Buckle the Galileo strap using the first or second hole and place it at the center of the cradle head, as shown in the picture. The cradle head is equipped with the wireless charger and the magnet. Buckle
First or second hole of Galileo strap Cradle head Auto adjustment head by magnet The coil for wireless charging function and magnetic to places the Galileo in right charging point are built in head of security cradle. When put the Galileo onto cradle, the magnetic power guides the device to center of cradle. If it is set apart from center, the charging will not Working. Built-in Wireless Charging Pad
Magnetic power set the Gear Sport to locate the charging point. 9 After finishing the installation, connect the Charging & security cable connector( ) to the Control box and turn on the power. Confirm that the LED of the Control box is ON. a
Press the ON switch.
Control box
Control box a How to separate the Security sensor Before separating the Security sensor, make sure to turn off the Control box. 1 Turn off the control box, remove the security cable connector( ), and remove the strap by pushing the strap spring bar handle in the arrow direction with the sharp part of Pin assembly/separation tool( ). If you remove the connector( ) without turning off the control box, an alarm will sound. 2 a a d c Detach the security sensor ( ) after first removing the strap. If you need to reinstall the security sensor, make sure to reapply the sensor pin protection sheet included in the maintenance kit to the security sensor again, as shown in the figure on the right. How to re-assemble the sensor pin protection sheet c
d
Handle of strap spring bar Do not push the handle of the spring bar in the opposite direction. The pin assembly/
separation tool may be damaged.
Control box a
c m2 Safety warning Warning: To prevent the injury of the user or other people and property damage, the following instructions must be followed.
Do not expose the product to fire or other electric heaters!
-There is a danger of fire or damage to the product.
Do not disassemble, repair, or remodel the product!
-There is a danger of injury.
-Please call the service center when repair is necessary.
Do not forcefully bend or pull the wire!
-There is a danger of damage to the product or injury to the user.
When the wire is disconnected or breaks away, do not touch the wire with bare hands, but always wear protective hand gloves!
-The disconnected part of the wire is sharp, thus, may cause injury.
Do not use the wire for purposes other than as a security alarm device, and do not allow access to children!
-Winding the wire around your neck or body may result in death or serious injury. Do not touch the wire when there is lightning and thunder!
-There is a danger of electric shock. The cable is a consumable product, so free repair service is not provided even within the warranty period in the event of damage or failure due to excessive use or intentional misuse.
The specifications and design(& color) of the product may be modified without prior notice for the improvement of product performance. MEMO Information Limited warranty Item Galileo Normal Security Set Warranty Period One year from shipment date. Manufacturer Information Manufacturer KUMOH Electronics Co.,Ltd Address TelFax
35, Gilju-ro 444beon-gil, Bucheon-si, Gyeonggi-do (Seoul 14556 Korea) 032-662-2000 / 032-662-9312 sale@kumohec.co.kr For detailed information about our service support, please contact us by email at sale@kumohec.co.kr or by phoning +82-32-662-2000 Free repair Charged repair We will provide repair services (including delivery charge) free of charge according to the our company's regulations for any failure or damage occurring during normal use according to the directions in the instruction manual within the warranty period. If the warranty period has expired, repairs can be provided for a fee. Furthermore, even during the warranty period the free repair service will not be provided in the following circumstances:
When damage has occurred due to the negligence or carelessness of the user.
When failure or damage have occurred due to an arbitrary repair, structural or performance modification by the consumer.
When failure or damage have occurred due to force majeure or fire. FCC Warning Statement FCC Part 15.19 This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC Part 15.21 Any changes or modifications (including the antennas) to this device that are not expressly approved by the manufacturer may void the users authority to operate the equipment. FCC Radiation Exposure Statement This equipment complies with FCC Radiation exposure limits set forth for an uncontrolled environment. This device and its antenna must not be co-located or operating in conjunction with any other antenna or transmitter. This equipment should be installed and operated with a minimum distance of 10cm between the radiator and your body. IC Warning Statement This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Le prsent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorise aux deux conditions suivantes : (1) L'appareil ne doit pas produire de brouillage, et (2) L'utilisateur de l'appareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible d'en compromettre le fonctionnement. IC Radiation Exposure Statement This equipment complies with IC RF Radiation exposure limits set forth for an uncontrolled environment. This device and its antenna must not be co-located or operating in conjunction with any other antenna or transmitter. This equipment should be installed and operated with a minimum distance of 10cm between the radiator and your body. Cet quipement est conforme aux limites tablies par Industrie Canada en matire d'exposition aux radiofrquences dans un environnement non contrl. Cet appareil et son antenne ne doivent pas tre colocaliss ou fonctionner en conjonction avec tout autre antenne ou metteur. Cet quipement doit tre install et utilis avec une distance minimale de 10cm entre le radiateur et votre corps.