Gear S2(3G/BT)/Gear S2 classic Normal Security Set(Redesign) INSTALLATION MANUAL G028_EN1612_R01 Before installing, Please check up the parts. Please, read carefully the installation manual before installing it, and install it according to the manual. Please, keep the manual for a future reference. Security sensor cable for Gear S2 BT(Bluetooth) Gear S2 BT - Side view Security sensor cable for Gear S2 3G Gear S2 3G - Side view Security sensor cable for Gear S2 classic Gear S2 classic - Side view Thickness 11.7mm Thickness 13.9mm Thickness 11.5mm g1 g2 Adaptor g3 g3 m1 m2 m3 h i j m3 a b 3 kinds of security sensor cables c Installation Guide - Gear S2 (3G/BT) /classic - Normal Security Set(Redesign) d e f Maintenance kit m4 Assembling flow g Gear S2(3G/BT)
/Gear S2 classic i j h c Ensure to use the adequate security sensor cable for each model before installing the product!
3 kinds of security cables are included in this package. Cable for Gear S2 Bluetooth (1EA), Cable for Gear S2 3G (1EA), and Cable for Gear S2 classic (1EA) After checking the Gear S2 model, ensure to select and install the security sensor cable that fits the model. The security sensor cable model can be identified by the label attached to the plastic bag or the imprinted text on the bottom surface of the sensor. a Security sensor cable for Gear S2 classic Gear S2 classic - Side view Thickness 11.5mm Plastic bag label Imprinted text at the bottom surface of the sensor
- S2 BT(S2 Bluetooth)
- S2 3G(S2 3G)
- S2 classic
(classic Bluetooth) b CAUTION A.
- Cautions when attaching the double-sided tape. 1.After removing the protective film from the double-sided adhesive tape, preserve the tape so that it doesn't get dirty. If touching the tape with a hand or foreign materials get on it, its adhesive strength can be significantly deteriorated. 2.The adhesive tape will have full adhesive strength after the 24 hours from its placement. Please do not use the products right after its placement. 1 Connect the connector of security sensor cable( ) to the connector at the bottom surface of the cradle( ) and insert it into the hole at the bottom surface of the cradle. Connect it while paying attention to the connector direction. b c 2 Insert the security sensor cable( ) mold groove into the cable mold guide on the cradle correctly and remove the protective film from the double-sided tapes on the bottom surface of the cradle( ). b c Cable mold groove c Remove the protective film c b Hole on the bottom surface Cable mold guide b Refer to Caution A. 3-A Insert the Charging & security cable( ) into the hole on the smart table while facing downward, and attach the cradle over the hole on the table. a 3-B Array the Charging & security cable( ) into the cable guide of the cradle properly, insert it into the hole on the table in the direction to the rear side of the cradle and attach it on the proper position firmly. a A - Installing on the smart table B - Installing on a normal table a Hole on the smart table a Cautions for removing the Gear S2 screw For installation of security sensor, the 2 screws at the top of Gear S2 should be disassembled. The screws of Gear S2 is not general screws but special screws which is hard to disassemble on purpose. When the screws are disassembled, please note below guidelines not to have damage on screws and surface of Gear S2. Disassemble Special Y screw Screw driver( ) for Y screw d Disassemble two screws as shown below. a Hole on the normal table a When you disassembling the screws, please proceed in accordance with below two guidelines. 1 If the angle of screw driver( ) is not stayed in 90 degrees, It can cause some scratches on the surface of the Gear S2 or abrasion on the top of the screws. 2 d After checking the Y type of screws and driver, be sure to be fitted with driver( ) an screw. When you disassemble the screw, it needs to be applied force downward by hand, then rotate driver counterclockwise slowly until the screw is disassembled completely. When you rotate driver counterclockwise, please be careful not to occur scratch or flaws by contact the surface of Gear S2 with driver. d O Stay 90 degrees
O Rotate Conuterclockwise d d
Security sensor installation method of Gear S2 3G and Gear S2 classic The installation for Gear S2 3G and Gear S2 classic is the same. Assemble the security sensor( ) with Gear S2 while paying attention to the assembling direction. After assembling the security sensor correctly, fix the Gear S2 and the security sensor by rotating the 8 mm screw( )to clockwise direction. Ensure to use the screw(8 mm) included in the package for fixing the security sensor. g3 c
g3 Rotate clockwise 1 Loosen the Gear S2 screw in the direction to the strap buckle counterclockwise using the screw driver included in the package. Make sure to removed the screw in the strap buckle direction of Gear S2. Keep the removed screw not to lose it. 2 Strap buckle Position of screws to be removed Gear S2 Screw Rotate counterclockwise c Gear S2 3G/
Gear S2 classic Installation method of Gear S2 Bluetooth security sensor Ensure to refer to the following only for installing Gear S2 Bluetooth model. 1 Loosen the screw of Gear S2 in the direction to the scrap buckle by rotating it counterclockwise and fix the adaptor by rotating the 6 mm screw( ) included in the package clockwise. Make sure to removed the screw in the strap buckle direction of Gear S2. Keep the removed screw as not to lose it. g1 2 Assemble the security sensor( ) to the adaptor while paying attention to the assembling direction. After assembling the security sensor correctly, fix the adaptor and the security sensor firmly by rotating the 3.5 mm screw( ) to clockwise direction. Ensure to use the screw included in the package for fixing the security sensor. g2 c Gear S2 Screw Rotate counter clockwise Gear S2 Bluetooth
g1 Rotate clockwise Adaptor c
g2 Rotate clockwise Installation method of Gear S2 classic strap clip Ensure to install it only for Gear S2 classic. Install the strap clip only for Gear S2 Classic. It is not necessary to install it for Gear S2 BT or Gear S2 3G. 1 Install the strap clip( ) at a distance of approximately 25 mm from the top of the strap. Insert the security sensor cable( ) into the cable groove between the strap clip. Insert the cable clip( ) into the Gear S2 classic band. Assemble the screw( ) using the screw driver( ), take one sealing sheet( ) and attach it on top of the screw head. Use the screw included in the plastic bag of the strap clip. 2 h j h d c i
h Cable groove i Sealing sheet
i j Gear S2 classic c h
2 When mounting Gear S2 on the cradle head, check if the cable of the Security sensor( ) c is installed correctly to direction of the rear side of the cradle as shown in the figure below. If the Security sensor is installed in the wrong direction, install it again by checking the assembling direction in of the installation of Security Sensor Cable. 1 c Cable direction Cable direction Mounting the product and connecting the control box 1 Install the buckle in the first hole of Gear S2 strap as below figure, and put the device on the center of cradle head. Make sure that the buckle should be installed in the first hole of strap. The wireless charger and the magnet are built in cradle head. Buckle The first hole of Gear S2 strap Cradle head Auto adjustment head by magnet The coil for wireless charging function and magnetic to places the Gear S2 in right charging point are built in head of security cradle. When put the Gear S2 onto cradle, the magnetic power guides the device to center of cradle. If it is set apart from center, the charging will not Working. Built-in Wireless Charging Pad
Magnetic power set the Gear S2 to locate the charging point. 3 f Assemble the security cable( ) temporarily using the cable tie( ) and the cable tie mount( ). Remove the protective film from the double-sided table on the bottom surface of the cable tie mount, attach the cable tie mount( ) firmly on the proper position on the table, pull and tighten up the table tie( ) completely and cut off any excess part. e f a e 4 After finishing the installation, connect the security cable connector( ) to the Control box and turn on the power. If the power supply is connected normally, LED on the Security sensor will turn on. a Check the LED lighting on the Security sensor e a f Cutting a Protective film Remove Press and hold evenly for 30 seconds or more!
Control box a How to separate the Security sensor Before separating the Security sensor, make sure to turn off the Control box. 1 g Turn off the control box, separate the security cable connector( ) and separate the screw( ) assembled to the security sensor by rotating it counterclockwise.
(In the case of Gear S2 BT, separate the adaptor after separating the security sensor.) If you separate the connector( ) without turning off the Control box, an alarm will occur. a a 2 c Separate the security sensor( ) and fix the screw is kept with the Gear S2 by rotating it clockwise direction. Make sure to use the screw separated from Gear S2 before installing the Security sensor. If the screw for installing the Security sensor is used, it will not be assembled normally. g Rotate counterclockwise c Gear S2 Screw Rotate clockwise Control box a Safety warning Warning: To prevent the injury of the user or other people and property damage, the following instructions must be followed.
Do not expose the product to fire or other electric heaters!
- There is a danger of fire or damage to the product.
Do not disassemble, repair, or remodel the product!
- There is a danger of injury.
- Please call the service center when repair is necessary.
Do not forcefully bend or pull the wire!
- There is a danger of damage to the product or injury to the user.
When the wire is disconnected or breaks away, do not touch the wire with bare hands, but always wear protective hand gloves!
- The disconnected part of the wire is sharp, thus, may cause injury.
Do not use the wire for purposes other than as a security alarm device, and do not allow access to children!
- Winding the wire around your neck or body may result in death or serious injury.
Do not touch the wire when there is lightning and thunder!
- There is a danger of electric shock. The specifications and design of the product may be modified without prior notice for the improvement of product performance.
Information Limited warranty Item
Warranty Period One-year
*In case of users fault during the warranty period it is not free of charge. Manufacturer Information Manufacturer KUMOH Electronics Co.,Ltd Address Tel Fax E-mail 35, Gilju-ro 444beon-gil, Wonmi-gu, Bucheon-si, Gyeonggi-do (Seoul 14556 Korea) 82-32-662-2000 82-32-662-9312 info@kumohec.co.kr FCC Warning Statement FCC Part 15.19 This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC Part 15.21 Any changes or modifications (including the antennas) to this device that are not expressly approved by the manufacturer may void the users authority to operate the equipment. FCC Radiation Exposure Statement This equipment complies with FCC Radiation exposure limits set forth for an uncontrolled environment. This device and its antenna must not be co-located or operating in conjunction with any other antenna or transmitter. This equipment should be installed and operated with a minimum distance of 10cm between the radiator and your body. IC Warning Statement This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Le prsent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorise aux deux conditions suivantes : (1) L'appareil ne doit pas produire de brouillage, et (2) L'utilisateur de l'appareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible d'en compromettre le fonctionnement. IC Radiation Exposure Statement This equipment complies with IC RF Radiation exposure limits set forth for an uncontrolled environment. This device and its antenna must not be co-located or operating in conjunction with any other antenna or transmitter. This equipment should be installed and operated with a minimum distance of 10cm between the radiator and your body. Cet quipement est conforme aux limites tablies par Industrie Canada en matire d'exposition aux radiofrquences dans un environnement non contrl. Cet appareil et son antenne ne doivent pas tre colocaliss ou fonctionner en conjonction avec tout autre antenne ou metteur. Cet quipement doit tre install et utilis avec une distance minimale de 10cm entre le radiateur et votre corps.