180905_Rev. 1.06 KIGIS IPAS User Manual Vehicle Tag(VT)Pedestrian Tag(PT) Wired Type [Standard]
I n t e l l i g e n t P r o x i m i t y A l e r t S y s t e m 1 Contents 1. What is IPAS?
2. Caution / Warning for Safety 3. Components / Names of Parts 4. Specifications 5. Installation 6. Setting
[IND] Danger / Caution Area Distance Setting
[IND] Volume Control
[IND] Setting Initialization
[IND] How to Set the Distance
[PT] Alarm type Setting
[PT] Volume Control 7. How to use Indicator Instruction that a driver must know PT instruction that a pedestrian must know LED status display 8. Check list before reporting failure 9. Warranty 3 4 5 6 7 8 ~ 10 8 8 8 9 10 10 11 ~ 12 11 11 12 13 15 Thank you for purchasing KIGIS IPAS product from KYUNGWOO SYSTECH, Inc. This product is a safety-assisting device to give warning signals by detecting the proximity of vehicles and pedestrians at industrial working site. Any property or life damage casued by the breach of safety regulation and users' carelessness will not be held responsibility. Before using this product, please read this manual carefully. Model No : PAS-K01-10 FCC ID : [VT]ZE8-PAS-K01-10 / [PT]ZE8- PAS-K01-00 Manufacturer : KYUNGWOO SYSTECH, Inc. / KOREA
* This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions : (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
* CAUTION : Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
* NOTE : This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. 2 1. What is IPAS?
KIGIS IPAS is an intelligent proximity alert safety and assistant system that prevents collisions by signaling dangers in 2 way communication to both drivers and pedestrians when pedestrians approach to a vehicle or vehicles approach to other vehicles in industrial working site. It is easy to install without causing any damages to the vehicle, and compared to other products, the outstanding proximity detection is an advantage that KIGIS IPAS only offers.
"Watch Out."
"Danger!"
"Beep-Beep-"
"Whee Yooo"
Danger Area Caution Area IPAS is applicable to all industrial vehicles.(excavators, forklifts, loaders, tractors, etc.) 3 2. Caution/Warning for Safety Caution!
Failure to observe the precautions in this manual may result in damage to the product or your property. DC 12/24V DC 12/24V Use only DC 12/24V. For vehicles with DC 36/48V, be sure to connect SMPS module to use DC 12/24V. Otherwise, this may cause trouble. Do not intentionally immerse the product in water or wash it in running water. This may cause trouble. Do not place the product near flammable materials, stoves, candles, or fire. This may cause fire and product deformation. If the product smells, smokes, or makes abnormal noises, turn off the power and contact the customer service center immediately. Caution!
Failure to follow the warnings in this manual may result in damage to the product or serious injury. Do not touch the connector or wiring with wet hands. This may cause electric shock or fire. If a connector or a wiring gets wet, wipe it with a dry towel. Otherwise, it may cause electric shock or fire. The pedestrian tag (PT) is a rechargeable product, so do not replace the battery. There is a risk of malfunction or explosion. Usage Precautions Since the pedestrian tag(PT) is a built-in battery product, please keep it in a cool place away from direct sunlight when not in use. Do not place heavy objects on the product or on wiring, or shock. It may cause electric shock or fire. Do not disassemble or modify this product. This may cause trouble, and After-
Sale Service will not be available. Combine PT and the holder in the proper way as shown in illustration. If not, a malfunction may be caused by an inflow of liquid matters.
* CAUTION Risk of explosion if battery is replaced by anincorrent type. Dispose of used batteries according to the instructions. Any accidents that result from not following the instructions in this manual are the users responsibility. 4 3. Components/Names of Parts Components Vehicle Tag(VT) Indicator Pedestrian Tag(PT) Helmet Holder Fuse Cable Harness(6m) Open Wire Adapter Cable High Speed Charging Cable(PT) Tag may not be recharged with general charging cable. User Manual It is strongly recommended that the tag should be installed on epaulet or arm band due to communication problem in case of installation at waist or in pocket. Optional Extension Cable Optional Cigar Jack Adapter Optional Clip Holder The appearance of the product may be slightly different from the actual product received. Names of Parts LED Lamp Detach Lever SET 1 Button STOP Button SET 2 Button LED Lamp Menu Button Power Button LED Lamp Charging Port Vehicle Tag(VT) Indicator Pedestrian Tag(PT) 5 4. Specifications Specifications Vehicle Tag(VT) Indicator Pedestrian Tag(PT) Product Image l E e c t r i c a l F e a t u r e Power 12/24V DC Input(9/32Vdc) 12/24V DC Input(9/32Vdc) Current 300mA 500mA Interface CAN Bus 2.0 CAN Bus 2.0
-
-
-
LED Status and Alarm method Normal operation
: Green LED flashing Approaching alarm
: Green/Red LED flashing Normal operation
: Green LED flashing Approaching alarm
: Green/Red LED flashing
+ Warning voice Normal operation
: Green LED flashing Approaching alarm
: alarm + vibration(3 options) Sound Level
/ @Distance -
Battery Operating Voltage Charge Interface
-
-
-
Charge Time -
Charge Current Operating Time
-
-
92dB / 0.1m 87dB / 0.1m
-
-
-
-
-
-
Lithium polymer 950mA 3.7V Micro USB Type-B(5V/1A) Approximately 1 hour 30 minutes 0.85mA 6 days(8 hours/day) F e a t u r e M e c h a n c a i l F e a t u r e U W B S p e c i f i c a t i o n O p e r e a t i o n Size 177.8 84.1 86mm 93 130.5 47.5mm 40 72 19.5mm Weight 444g 207g 58.5g Mounting Method Magnet pad attachment method Fixed with screw
(or adhesive tape) Clip, Necklace chain Frequency 3993.6MHz Bandwidth 499.2MHz Detdction Cycle 0.5sec Operating Temperature -30 ~ 85C Storage Temperature -40 ~ 85C Waterproof IP65
-
-
-
-30 ~ 85C
-40 ~ 85C IP65 3993.6MHz 499.2MHz 0.5sec
-20 ~ 55C
-20 ~ 55C Basic waterproof Some features may change without prior notice to improve the performance of the product. 6 5. Installation Caution! It is highly recommended to install IPAS with the power off. Turn on the power after connecting all products. Vehicle Tag(VT) Cable Harness(6m) Open Wire Adapter Cable or Indicator 5m 3 m or Cigar Jack Adapter
* Normal operation : Green Flash ON after turning on the power.
* Caution! Wind up cable terminals to properly connect them. Disregarding this caution, it may cause a malfunction caused by liquid matters. Setting Tips It is more desirable to install VT in a 360open space for example on top of cabin, rather than a space insde cabin. This product, as a wireless frequency(RF) device, is better communicative in operation in a open space. KIGIS IPAS is designed with the customer in mind for easy installation without the help of an installer. The powerful magnet can be attached easily on VT floor without damaging the vehicle and it is also convenient to detach with detach lever. It can be easily installed by using cable ties in case of no magnet on vehicle. Magnetic Pad : Easy to install Detach lever : Easy to detach from vehicle by pulling the lever as shown Pedestrian Tag Helmet Clip Fastening Tie Hole 7 6. Setting - Indicator Danger / Caution Area Distance Setting In a condition of normal operation Press and hold SET 1 and SET 2 buttons simultaneously for 2 seconds or more. Set the desired Danger Area distance by operating the SET 1 and SET 2 buttons. (Refer to "How to set the distance" on the following page) Press STOP to complete the Danger Area setting. When the green LED is on, set the distance to the Caution Area. Set the desired Caution Area distance by operating the SET 1 and SET 2 buttons. (Refer to "How to set the distance" on the following page) Volume Control Press STOP to complete the Caution Area setting. In a condition of normal operation SET 1 Button : - Volume SET 2 Button : + Volume Setting Initialization In case of malfunction Press and hold the STOP button for more than 2 seconds. When the red LED is flashing sequentially, press and hold the STOP button again for more than 2 seconds. The LED will turn off and the setting will be initialized. Reboot will take about 5 seconds.(Do not turn off the vehicle until the green LED flashes.) Default values after initialization : 4m for Danger Area / 8m for Caution Area 8 6. Setting - Indicator How to Set the Distance Distance setting can be set to even distance [2 / 4 / 6 / 8 / 10m] or odd distance [1 / 3 / 5 / 7 / 9m]. The default setting is even distance. SET 1 button : Distance -2 m STOP button : OK SET 2 button : Distance + 2m 2m space per LED lamp [ ]
OFF ON
: 2m or 1m
: 4m or 3m
: 6m or 5m
: 8m or 7m
: 10m or 9m
* Odd distance [1 / 3 / 5 / 7 / 9m] change : Press and hold SET 1 button + STOP button at the same time.
< Example > Setting Danger Area 3m / Caution Area 9m Set an even distance 1m longer than the desired Danger /Caution Area as shown below.
(Set 3m 4m / 9m 10m) Danger Area (Red LED) Caution Area (Green LED)
: 4m
: 10m Press & hold SET 1 button + STOP button at the same time, It is set to be 1m Shorter and it changes into 3m distance for Danger Area / 9m distance for Caution Area. If you want to change from odd distance to even distance again, press and hold Set 2 & STOP. Setting Tips As IPAS releases warning signals by detecting the proxmity on 0.5 second cycles, proximity distance must be set considering vehicle speed. 9 6. Setting - Pedestrian Tags Alarm type Setting Press and hold the Press and hold the power button to turn on the power.
(Charging is required if the red LED is on.) menu button.
( A short vibration will occur.) Press the power button to set the desired alarm type.
( Please refer to the alarm system below.) Press and hold the menu button to complete the setup. Press Power button 1 time
>
Default Status
(Sound +
Vibration) Sound
>
l A a r m Rotation Press Power button 1 more time
>
Press Power button 1 more time
>
Vibration
>
>
Press Power button 1 more time Volume Control Sound
+
Vibration Press and hold the Press and hold the Press the menu button Press and hold the power button to turn on the power. menu button.
( A short vibration will
( Charging is required if occur.) the red LED is on.) to set the desired volume level.
( See volume steps below.) menu button to complete the setup. l V o u m e S t a g e Press Menu button 1 time
>
Default Status
(Stage 3) Stage 3
>
Rotation Press Menu button 1 more time
>
Press Menu button 1 more time
>
Stage 2 Stage 1
>
>
Press Menu button 1 more time 10 7. How to use Indicator Instruction that a driver must know Situation LED Lamp Status Alarm Mute Alarm When a pedestrian(PT) trespass on the Caution Area When a pedestrian(PT) trespass on the Danger Area Red / Green Light flashes gradually Repeating
"Watch Out"
Repeating
"Danger"
Press STOP Button 1 Time Even though alarm ismuted (double clikc), in case that pedestrian escapes the set Danger / Caution Area and re-
enters them, the alarm will go off again.
* When pedestrian enters and escapes out of Danger/Caution Area, for the safety of pedestrians, the alarm will go off from the point 1m further away that was set originally.
(Example : If the Danger Area / Caution Area is set at 2m / 4m, the warning sound of PT will go off until it escapes 3m of Danger Area and 5m of Caution Area from VT) Volume Control : Refer to 8P How to use "PT" that pedestrians must know Situation LED Lamp Status Alarm Alarm Pause Mute Alarm When a pedestrian(PT) trespass on the Caution Area When a pedestrian(PT) trespass on the Danger Area Green Flash
"Beep-Beep-" sound Vibration
(short interval) Both Depends on menu setting
"Whee yooo whee yooo"(siren) Vibration
(long interval) Both Depends on menu setting Press menu or power button one time. Alarm will occur in 10 seconds automatically after pause. Press menu or power button twice quickly.
("Beep" alarm will occur.) Even though alarm ismuted (double click), in case that pedestrian escapes the set Danger
/ Caution Area and re-
enters them, the alarm will go off again. When the battery is low
(Less than about 4 hours of use) Red Flash
"Beebeep Beebeep"
5 times every 10 minutes.
-
-
* When pedestrian enters and escapes out of Danger/Caution Area, for the safety of pedestrians, the alarm will go off from the point 1m further away that was set originally.
(Example : If the Danger Area / Caution Area is set at 2m / 4m, the warning sound of PT will go off until it escapes 3m of Danger Area and 5m of Caution Area from VT) Alarm type setting / Volume Control : Refer to 10P Caution!
O Right exemple X Wrong exemple Charging Port Charging Port A malfunction may be caused by combining products backwards. 11 7. How to use - LED status display LED Status Vehicle Tag(VT) Indicator Pedestrian Tag(PT) Power ON Power OFF Normal Low Voltage Battery Battery Charging Fully Charged Entering Caution Area Entering Danger Area Green Flash Green Flash Green Flash LED Off LED Off After Red light blinks once, it turns off Green Flash Green Flash Green Flash
-
-
-
-
-
-
-
-
-
-
-
-
Red Flash Red On Green On
+
+
Green + Red flashing Green + Red flashing Green Flash
+
+
Green + Red flashing Green + Red flashing Green Flash 12 8. Check list before reporting failure Question Reason Solution Access to PT MENU is unavailable. You can access the menu after turning on the power. If you press and hold the power button for 2 seconds, the green LED will blink. Press and hold the menu button for 2 seconds afterward. There is a red LED on the PT. It is a signal indicating low voltage when the remaining battery power is less than 4 hours. Please charge it. When it is 100% charged, the green LED will turn on. The volume of VT sound is too low. Can I mute the alarm when I drive a vehicle with a PT?
Can I pause an alarm to talk to a VT car driver for a moment?
Previously set distance of Danger/
Caution area is not precise. Indicator's volume setting is low. The indicator can be adjusted up to 5 levels.
(How to adjust the indicator volume
: see 8P) Mute of alarm sound is possible.
<How to mute alarm>
* PT : Press twice quickly Menu or Power button with short intervals.
* Indicator : Press STOP button once (When PT owner deviates and reenters the Danger
/ Caution area, the alarm will go off again) It is possible to pause for 10 seconds. After 10 seconds, the alarm will occur again.
<Alarm pause tip>
* PT : 1 time quick press on Menu or Power button. (PT alarm will go off after 10 seconds automatically) A. The alert sounds in shorter horizontal distance depending on the installation height of VT. B. When getting inside and getting out of the Danger / Caution Area, alarm will go off 1m further from the set distance for the safety reason. <Example> In case of setting 2m for Danger Area and 4m for Caution Area, alarm will keep going off until getting out of 3m (Danger Area) and 5m (Caution Area). In case of A and B, it is normal function but when they are thought to be an issue, it is recommended to initialize the indicator to reset the distance for use from a scratch.
(See Indicator initialization and distance setting 8P) If you have any questions, please feel free to contact us at www.kyungwoo.com. 13 M E M O W A R R A N T Y Warranty Term 1 year from the purchase date Product Name Model Name Place of Purchase Date of Purchase Name of Customer Phone Number
* Service information 1. If a performance or functional failure occurs while proper using during the warranty period, the repair service is free of charge. 2. When the repair service is required, please present the warranty card with all information filled in. 3. The following cases will be charged for the repair regardless of warranty period. Failure due to careless use or improper repair or modification Failure due to non-compliance to the specifications stated in this manual 4. After the expiration of warranty period, a certain fee will be charged for the repair service. 5. The warranty card cannot be reissued. If failures occur when a person who is not in our service team tries to repair the product and breaks down, or uses components from other companies, we will not hold the responsibility for those failures. Please contact the store where you purchased the product for the refund or exchange of the product. 4F, Daeryung Post Tower 5, 68, Digital-ro 9-gil, Geumcheon-gu, Seoul, 08512, Republic of Korea T h i n k S m a r t , W o r k S a f e Distributor(or purchasing store)
* Any inquiry about the purchased product is contactable to distributor(or purchasing store) at below line. Manufacturer KYUNGWOO SYSTECH, INC. 4F, Daeryung Post Tower 5, 68, Digital-ro 9-gil, Geumcheon-gu, Seoul, 08512, Republic of Korea Tel. +82-2-985-8085 Fax. +82-2-985-8087 E mail. info@kigistec.com www.kyungwoo.com / www.kigistec.com