FCC ID: 2ARW2-SMARTGATEWAY Remote Control

SMART GATEWAY Wi-Fi command interface / RF 433.92 MHz for connection between L&S receivers and devices with Wi-Fi connection. INDEX 1 - PRODUCT FEATURES 1.1 - TECHNICAL DATA 1.2 - USE 2 - NETWORK CONFIGURATION 3 - SYSTEM CONFIGURATION 2.1 - INTRODUCTION 2.2 - PROCEDURE FOR USING A HOTSPOT CONNECTION 2.3 - PROCEDURA PER LUTILIZZO CON RETE WIFI ESISTENTE 3.1 - INTRODUCTION 3.2 - CREATING A DEVICE / ASSOCIATING THE DEVICE WITH THE RECEIVER 3.3 - DELETING OR MODIFYING A CREATED DEVICE 3.4 - CREATING A GROUP 3.5 - DELETING OR MODIFYING A CREATED GROUP 4 - GENERAL SETTINGS 5 - USER INTERFACE WINDOWS 5.1 - INTRODUCTION 5.2 - HOMEPAGE/DEVICES 5.3 - ZONES 5.4 - SCENARIOS 5.5 - PROGRAMMING THE TIMER 6 - FURTHER DETAILS 6.1 - CREATING A QUICK ACCESS COMMAND 6.2 - VERIFY THE NETWORK IP ADDRESS 7 - RECALL A SCENARIO USING TRANSMITTER 7.1 - INTRODUCTION 7.2 - ASSOCIATION OF THE TRANSMITTER 7.3 - ASSOCIATING A SCENARIO WITH THE TRANSMITTER KEY 7.4 - DELETING A TRANSMITTER 8 - RESET THE SYSTEM 8.1 - RESET THE NETWORK CONFIGURATION 8.2 - RESET THE SYSTEM CONFIGURATION This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. 025-FIS18_Smart_GATEWAY 1 1 - PRODUCT FEATURES 1.1 TECHNICAL DATA Power supply Type of communication Number of devices (mobile phones, PCs, etc.) simultaneously connected Type of communication with receivers Number of controllable receivers Protection rating Operating temperature Dimensions 230Vac Wi- 50 433.920MHz ISM 20 IP20

-20 +55 C 174x46x35 mm 67mm 72mm 63mm Picture 1.1b KEY Y key= reset network conguration

(if reset in hotspot with default password). See paragraph 7.1 A y LED A

- Red/green/blue lights turn on in sequence when powered ON

- Flashes red while creating/connectiong to a network

- Blue light turn on if you set connecting to an existing network

- Red light turn on if you set creating a network hotspot 1 2 025-FIS18_Smart_GATEWAY 1.2 USE To use the product you need:

- a Wi-Fi compatible device (e.g.: tablet, PC or Smartphone)

- Compatible radio receivers To activate the system, follow the instructions in paragraph 2 on how to congure the hub network and access the application. Next, follow the instructions in paragraph 3 on how to create user screens and associate them with the receiver 2 - NETWORK CONFIGURATION 2.1 INTRODUCTION The device can operate in two modes:

- the hub generates a Wi-Fi hotspot. To use the device, it must be connected to this network (therefore, not connected to any other networks)

- connect the hub to an existing Wi-Fi network. Once congured, the hub can also be accessed when connected to the existing network. The rst solution is ideal for locations where no Wi-Fi network is available, but you wish to use a personal device for driving the loads. The second solution makes it possible to remain connected to existing Wi-Fi networks (e.g.: have internet access), while using the hub at the same time. According to the specications of the system, follow the instructions in:

- paragraph 2.2 to connect the hub for use with a hotspot

- paragraph 2.3 to connect the hub for use with an existing network TYPE OF SYSTEM WITH HUB CONNECTED TO HOTSPOT Device with Wi-Fi connection

(e.g.: Smartphone) Hub100 L&S Receivers TYPE OF SYSTEM WITH HUB CONNECTED TO EXISTING WI-FI NETWORK Device with Wi-Fi connection

(e.g.: Smartphone) Existing Wi-Fi Network Hub100 L&S Receivers 3 2 025-FIS18_Smart_GATEWAY 2.2 PROCEDURE FOR USING A HOTSPOT CONNECTION STEP1 Power ON the hub. Red/green/blue lights turn on in sequence. After the LED will ash red during this phase (about 1 minute): the hub is generating the Wi-Fi hotspot STEP2*

The LED switch ON and remain

xed on green:

use your own device (e.g.: Smar-

tphone) and search available networks for "Hub Smart Control", the hotspot generated by the hub. STEP3*

To connect to this network, insert the default password:

"12345678"

NOTE: when connected to this network, connections to other networks will be disabled and access to the internet is unavailable Hub Smart Control ENTER PASSWORD 12345678 Access STEP4*

You are now connected to the hotspot generated by the hub. Next, type the default name of the hub, "http://hub100.", in the address bar of the browser on your device. http://hub100. Type a website address Wi-Fi Activated CHOOSE A NETWORK... Hub Smart Control STEP5 The user interface window will open. Click on "menu". menu Devices STEP8 Click on "congure network"

STEP9 The current setting will be displayed; click on "edit"

congure network Settings Congure network CONFIGURE NETWORK Congure current network Type of access : Hub hotspot SSID : Hub Smart Control Edit Edit 4 lampeggia rosso STEP6 Click on "Congure network"

NOTE: this operation is not necessary for usage, but it makes the hub more secure and blocks unwanted access to the system. Congure network Devices Settings Congure network Congure system STEP7*

You will be requested to enter a password; the default password is: 1234. 1234 Password Enter password Conrm Cancel

*NOTE: In steps 2, 3, 4 and 7 of this procedure, the default values to be used will be suggested. If these were modi-

ed previously, the system must be reset; see paragraph 7.1. 3 025-FIS18_Smart_GATEWAY STEP10 Click on "Hub hotspot"

Hub hotspot Edit network Select connection type Hub hotspot Wi-Fi network STEP12 After lling in all the elds, click on

"Save" at the bottom of the page. Network name (ssid) Current password New password Conrm password System System Name Save Save STEP11 Fill in all elds with the connection data for the hotspot you wish to create. Network name (SSID): the name of the hotspot generated by the hub. See step 2 of this procedure (default: Hub Smart Control) Current password: the existing password required to connect to the hotspot used in step 3 of this procedure (default: 12345678) New password: the new password which will be used in step 3. It is recommended to set a new password for security reasons. System name: the name to enter in the address bar of step 4 of this procedure. The name cannot contain spaces. NOTE: when entering the name in the address bar, it must always end with a full stop (.) EXAMPLE:

system name:

address to enter:

ATTENTION:

To access the system with another device (mobile phone, PC, etc.) once the system has been congured, simply follow step 14. The IP address to connect to is visible on the congure network page in the settings menu of a device which has already been congured hubcasa http://hubcasa. NOTE:

it is important to remember the infor-

mation entered as it is required in order to use the hub with your own device and to connect more devices at a later time. If the data are lost, the system must be reset by following the procedure in paragraph 7.1. Edit network Select connection type Hub hotspot Network wi Hub hotspot conection Network name (ssid) Current password New password Conrm password System System Name Save STEP13 The hub will restart to activate the new settings;

the LED will ash red while creating the hotspot

(about 1 minute). The personal device will disconnect from the hubs hotspot network. STEP14 To use the system, reconnect to the hubs Wi-Fi network (steps 2, 3 and 4 of this procedure) using the new data entered during step 11. NOTE: it is recommended to create an icon on the homepage of the personal device so you can quickly access the commands; see paragraph 6.1 5 4 025-FIS18_Smart_GATEWAY 2.3 PROCEDURA PER LUTILIZZO CON RETE WIFI ESISTENTE STEP1 Power ON the hub. Red/green/blue lights turn on in sequence. After the LED will ash red during this phase (about 1 minute): the hub is generating the Wi-Fi hotspot STEP2*

The LED switch ON and remain

xed on green:

use your own device (e.g.: Smar-

tphone) and search available networks for "Hub Smart Control", the hotspot generated by the hub. STEP3*

To connect to this network, insert the default password:

"12345678"

NOTE: when connected to this network, connections to other networks will be disabled and access to the internet is unavailable Hub Smart Control ENTER PASSWORD 12345678 Access STEP4*

You are now connected to the hotspot generated by the hub. Next, type the default name of the hub, "http://hub100.", in the address bar of the browser on your device. http://hub100. Type a website address Wi-Fi Activated CHOOSE A NETWORK... Hub Smart Control STEP5 The user interface window will open. Click on "menu". menu Devices STEP8 Click on "congure network"

STEP9 The current setting will be displayed; click on "edit"

congure network Settings Congure network CONFIGURE NETWORK Congure current network Type of access : Hub hotspot SSID : Hub Smart Control Edit Edit 6 lampeggia rosso STEP6 Click on "Congure network"

NOTE: this operation is not neces-

sary for usage, but it makes the hub more secure and blocks unwanted access to the system. Congure network Devices Settings Congure network Congure system STEP7*

You will be requested to enter a password; the default password is: 1234. 1234 Password Enter password Conrm Cancel

*NOTE: In steps 2, 3, 4 and 7 of this procedure, the default values to be used will be suggested. If these were modi-

ed previously, the system must be reset; see paragraph 7.1. 5 025-FIS18_Smart_GATEWAY STEP10 Click on "Wi-Fi network"

Network wi Edit network Select connection type Hub hotspot Network wi STEP12 After lling in all the elds, click on

"Save" at the bottom of the page. SSID Encryption Network1 Password Static IP setting IP adress 192.168.1.200 Save Save STEP11 A list of existing networks detected by the hub will appear. Select the network you wish to connect the device to, and enter the password used to access the existing network. Congure a static IP address:

IP ADDRESS: the network address to be associated with the hub. If you know an available address in your network, enter it. If you do not know this parameter, try to connect using the suggested default address, or see paragraph 6.2. This address will then be used to connect to the user command interface;

see step 14. ATTENTION:

To access the system with another device (mobile phone, PC, etc.) once the system has been congured, simply follow step 14. The IP address to connect to is visible on the congure network page in the settings menu of a device which has already been congured; see

"URL" entry Edit network Select connection type Hub hotspot Network wi Available Wi-Fi networks SSID Encryption Network1 Password Static IP setting IP adress 192.168.1.200 Net mask 255.255.0.0 Save STEP13 The hub will restart to activate the new settings, and then connect to the existing Wi-Fi network. The LED will ash blue during this phase (about 1 minute). After, will remain xed on blue. The device will disconnect from the hub hotspot. If the connection is unsuccessful see possible causes below STEP14 To use the system:

- connect your device to the existing Wi-Fi network to which the hub was connected

- open the browser and, in the address bar, type the IP address which was saved in step 11 NOTE: it is recommended to create an icon on the homepage of the personal device so you can quickly access the commands; see paragraph 6.1 POSSIBLE REASONS FOR FAILURE TO CONNECT TO AN EXISTING NETWORK Check the values entered in step 11 of this procedure. The following are the most likely causes:

- incorrect network password: verify you have entered the correct network access password

- incorrect IP address: an address already in use, or incorrect address, was entered. See paragraph 6.2

- network not found: verify the Wi-Fi network is available Make a reset (see paragraph 7.1) and do again this procedure from step 2. 7 6 025-FIS18_Smart_GATEWAY 3 - SYSTEM CONFIGURATION 3.1 INTRODUCTION After the procedure in paragraph 2 is complete, the personal device is able to communicate with the hub. The following step creates the various user command interfaces which will appear on the home screen of the application. These interfaces can be either devices or groups. Devices: the term device refers to an interface which is used to drive a load (e.g.: light or roller shutters) Groups: the term groups refers to an interface which is used to drive a set of previously created devices. This is useful for creating a "switch OFF all lights" command or "lower all roller shutters" command. To create devices, see paragraphs 3.2 and 3.3; to create groups, see paragraphs 3.3 and 3.4. NOTE: both devices and groups will appear on the homepage. It is recommended to use the name which is assigned to each interface to distinguish group commands from commands for a single device 3.2a CREATING A DEVICE STEP1 Access the application according to the network conguration performed in paragraph 2 STEP2 Click on "menu". STEP3 Click on "Congure system"

menu Devices Congure system Devices Settings Congure network Congure system STEP6 A list of created devices will appear (the default list has no devices). Click on the "+" button to add devices

+

List of Devices STEP5 Click on "list of devices"

list of devices Congure system LIST OF DEVICES LIST OF GROUPS RESET STEP4*

You will be requested to enter a password; the default password is: 1234. 1234 Password Enter password Conrm Cancel 7 8 025-FIS18_Smart_GATEWAY STEP7 The elds to ll in to create the device will appear:

NAME: the name which will appear on the homepage TYPE OF COMMAND: determines the user command interface and, therefore, the actions which can be perfor-

med. This eld is chosen according to the receiver to be controlled. See the table below ICON: the graphic icon which appears to the side of the device; for graphic purposes only Congure system Name Type of command Icon Save TYPE OF COMMAND On-Off Open-Stop-Close Impulse Dimmer light RGB/RGBW light Tunable white light EXECUTABLE ACTIONS On - Off Open - Stop - Close Impulse On - Off - Intensity setting On - Off - Intensity setting - Colour management On - Off - Intensity setting - Tunable light management STEP8 Click on "save" at the bottom of the page. Saving device Deviced saved STEP9 The application displays the list of updated devices. If you wish to add more devices, return to step 2 of this procedu-

re. If all user command interfaces have been created, go to step 3.2b to associate them with the central receivers. NOTE In step 4 of the procedure, the default values to be used will be suggested. If these were modied previously and cannot be recovered, the system must be reset; see paragraph 7.1. A reset will not delete systems created in the interface (see paragraph 3); it will only reset the network settings

(network name, page address, password). The default password from "step 4" can be changed by accessing "menu-settings-change password". 9 8 025-FIS18_Smart_GATEWAY 3.2b ASSOCIATING THE DEVICE WITH THE RECEIVER After the procedure in paragraph 3.2a is complete, the various devices which have been created will be displayed on the homepage of the application. The next step is to associate each device with the receiver to be driven. The receiver must be accessed to complete this step. PROCEDURE STEP1 Access the receiver and perform the radio programming procedure for the multifunction radio transmitters. See receiver manual. THE LED TURNS ON THE LED TURNS ON Make a short press of the button SMART1 Make a short press of the button related to the output which the transmitter wants to be programmed. SMART4 STEP2 While programming the radio, you will be requested to transmit a command. To transmit the command, select the device on the homepage and transmit any command using the keys available. The receiver ashes three times to conrm programming was successful. LED MAKES 3 FLASHES AND TURNS OFF LED MAKES 3 FLASHES AND TURNS OFF SMART1 SMART4 SELECT THE DEVICE ON THE HOMEPAGE AND TRANSMIT ANY COMMAND USING THE KEYS AVAILABLE 9 10 025-FIS18_Smart_GATEWAY 3.3 DELETING OR MODIFYING A CREATED DEVICE If you wish to delete or modify a created device, change the name, icon or the type of command, perform the following procedure:

STEP1 Access the application according to the network conguration performed in paragraph 2 STEP2 Click on "menu". STEP3 Click on "Congure system"

menu Devices Congure system Devices Settings Congure network Congure system STEP6 A list of created devices will appear. Select the device to be modied STEP5 Premere su lista dispositivi list of devices List of devices Device 1 Congure system LIST OF DEVICES LIST OF GROUPS RESET STEP4*

You will be requested to enter a password; the default password is: 1234. 1234 Password Enter password Conrm Cancel STEP7 Click on "edit to change the settings or "delete" to remove it List of devices Device 1 Edit Delete ATTENTION In step 4 of the procedure, the default values to be used will be suggested. If these were modied previously and cannot be recovered, the system must be reset; see paragraph 7.1. A reset will not delete systems created in the interface (see paragraph 3);

it will only reset the network settings (network name, page address, password). The default password from "step 4" can be changed by accessing

"menu-settings-change password"

11 10 025-FIS18_Smart_GATEWAY 3.4 CREATING A GROUP After creating several devices, a group (comprising several individual devices) can be created to send multiple load commands with a single action. This procedure offers the advantage of creating and modifying groups without having to access the central receivers; the commands will be sent sequentially, i.e. in series. If, for example, the OFF command is sent to a group of three devices, the three lights will power OFF in sequence. To command groups simultaneously, perform the device creation procedure (paragraph 3.2a) and associate all the receivers you wish to be part of the group, rather than a single device (paragraph 3.2b). PROCEDURE:

STEP1 Access the application according to the network conguration performed in paragraph 2 STEP2 Click on "menu". STEP3 Click on "Congure system"

menu Devices Congure system Devices Settings Congure network Congure system STEP6 A list of the created groups will appear (the default list has no devices). Click on the "+" button to add a group

+

List of groups STEP5 Click on "list of groups"

List of groups Congure system LIST OF DEVICES LIST OF GROUPS RESET STEP4*

You will be requested to enter a password; the default password is: 1234. 1234 Password Enter password Conrm Cancel 11 12 025-FIS18_Smart_GATEWAY STEP7 The elds to ll in to create the group will appear:

NAME: the name which will appear on the homepage TYPE OF COMMAND: determines the user command interface and, therefore, the actions which can be perfor-

med. This eld is selected according to the devices which are part of the group: for example, if the group includes a combination of coloured lights and dimmer lights, and a type of command such as "RGB/RGBW lighting" is selected, the dimmer lights will remain unchanged if a colour command is transmitted. Congure system Name Select devices Type of command Icon Save TYPE OF COMMAND On-Off Open-Stop-Close Impulse Dimmer light RGB/RGBW light Tunable white light EXECUTABLE ACTIONS On - Off Open - Stop - Close Impulse On - Off - Intensity setting On - Off - Intensity setting - Colour management On - Off - Intensity setting - Tunable light management STEP8 Click on "save" at the bottom of the page. STEP9 The application displays the list of updated devices. If you wish to add more groups, return to step 2 of this procedure. Saving device Deviced saved ATTENZIONE In step 4 of the procedure, the default values to be used will be suggested. If these were modied previously and cannot be recovered, the system must be reset; see paragraph 7.1. A reset will not delete systems created in the interface (see paragraph 3); it will only reset the network settings

(network name, page address, password). The default password from "step 4" can be changed by accessing "menu-settings-change password"

13 12 025-FIS18_Smart_GATEWAY 3.5 DELETING OR MODIFYING A CREATED GROUP If you wish to delete or modify a created device, change the name, icon or the type of command, perform the following procedure:

STEP1 Access the application according to the network conguration performed in paragraph 2 STEP2 Click on "menu". STEP3 Click on "Congure system"

menu Devices Congure system Devices Settings Congure network Congure system STEP6 A list of created groups will appear. Select the group to be modied STEP5 Click on "list of groups"

list of groups List of groups Light group 1 Congure system LIST OF DEVICES LIST OF GROUPS RESET STEP4*

You will be requested to enter a password; the default password is: 1234. 1234 Password Enter password Conrm Cancel STEP7 Click on "edit to change the settings or "delete" to remove it List of groups Light group 1 Edit Delete ATTENZIONE In step 4 of the procedure, the default values to be used will be suggested. If these were modied previously and cannot be recovered, the system must be reset; see paragraph 7.1. A reset will not delete systems created in the interface (see paragraph 3);

it will only reset the network settings (network name, page address, password). The default password from "step 4" can be changed by accessing "menu-set-

tings-change password"

13 14 025-FIS18_Smart_GATEWAY 4 - GENERAL SETTINGS 4.1 EDITING THE GENERAL SETTINGS The following settings can be modied:LINGUA: modica la lingua dei testi dellapplicazione DATA/ORA: serve ad impostare data e ora allinterno dellapplicazione. Questimpostazione necessaria per utilizzare le programmazioni orarie PASSWORD: change the network and system conguration access password; see paragraphs 2 and 3 PROCEDURE STEP1 Access the application according to the network conguration performed in paragraph 2 STEP2 Click on "menu". STEP3 Click on "Settings"

menu Devices Settings Devices Settings Congure network Congure system STEP4 Click on the parameter you wish to modify Settings CHANGE LANGUAGE EDIT DATE/TIME CHANGE PASSWORD Modica Elimina 15 14 025-FIS18_Smart_GATEWAY HOMEPAGE / DEVICES: all created devices and groups are displayed in SCENARIOS: scenarios can be created by inputting different actions in different ZONES: the devices and groups can be divided into zones to facilitate use, see 5 - USER INTERFACE WINDOWS 5.1 INTRODUCTION Once the hub has been congured (paragraph 2), the devices have been created and associated (paragraph 3.2), as well as any groups (paragraph 3.4), the application is ready for use. There are 4 main command screens:

alphabetical order; see paragraph 5.2 paragraph 5.3 devices; see paragraph 5.4 automatically activate at the desired time. See paragraph 5.5 To switch from one screen to another, click on the related icon. The red cursor indicates which screen is active. 5.2 HOMEPAGE/DEVICES The created devices and groups are displayed in alphabetical order on the homepage. Each device will have its own user command interface according to the "type of command" selected during the procedure in paragraph 3.2a. The following example describes each type of interface along with its functionality. NOTE: in the example, the device name which appears on the homepage corresponds to the type of command; the name entered by the user during the procedure in paragraph 3.2 will appear, in a real situation HOURLY PROGRAMMING: actions can be created for devices which Devices Icon of the selected screen Devices Open-Stop-Close Impulse Dimmer Ligh RGB/RGBW light Tunable white light On-Off

%

B G R T C C Type of command "Open-Stop-Close"

Type of command "Impulse"

Device name Device name 15 16 025-FIS18_Smart_GATEWAY Type of command "Dimmer Light"

Type of command On-Off Device name Device name ON OFF ON OFF Intensity Type of command "RGB/RGBW Light"

Device name Color Memo ON OFF Intensity Click on Type of command "Dynamic White Light"

Device name Color Memo ON OFF Click on

<

Device name R:25 G:142 B:191 Save:

Saves light colour setting for the next time it is powered ON White Light:

sets the white light

:

play / stop cycle RGB:

sets the three values for R, G and B Effect speed:

colour settings for the colour cycle Effect speed:

sets the duration of the colour cycle Save:

Saves light temperature setting for the next time it is powered ON Neutral white:

sets the neutral white light Save White light R G B Effect Effect speed

<

Device name Intensity Memo Bianco neutro 17 16 025-FIS18_Smart_GATEWAY 5.3 ZONES The default setting of the zones screen is empty. The user can reorganise the created devices and groups (displayed on the homepage screen) to facilitate access and use. EXAMPLE:

CI create the "living room" zone where I insert both the lights and the roller shutters in the room. I create the "garden" zone which includes the devices located in the garden. PROCEDURE FOR CREATING ZONES STEP1 Click on the zones icon. Only devices which have been divided and organised into zones are displayed. STEP2 Click on the "+" icon. The zones creation menu will open Zones

+

Zones Zone STEP4 The application returns to the "zones" menu and displays the created zones. To create more zones, return to step 2 STEP3 Enter the name of the zone (e.g.: living room) and select the devices and groups which are in the zone;

now click on "save zone". Zones Living room Dimmer light RGB/RGBW light

%

B G R Name of the zone Selection New zone Name Living room List of device Open-Stop/Close Impulse Dimmer light RGB/RGBW light Tunable white lightOn-Off List of groups Ground oor lights List of devices List of groups Save zone Save 17 18 025-FIS18_Smart_GATEWAY PROCEDURE FOR DELETION OR MODIFICATION OF CREATED ZONES If you wish to delete or modify a created zone, change its name or the devices which are a part of the zone, perform the following procedure:

STEP1 Click on the zones icon. Only devices which have been divided and organised into zones are displayed. STEP2 Click on the "pencil" icon. The "gear" icon is displayed next to each zone. pencil gear Zones Living room Dimmer light RGB/RGBW light

%

B G R Zones Living room Dimmer light RGB/RGBW light

%

B G R Zone STEP4 EDIT: modify the values and click on "Save zone"

DELETE: click on the "recycle bin" icon STEP3 Click on the name of the zone you wish to delete or modify. The zone settings menu will be displayed, along with the parameter settings. New zone New zone Nome Living room Name Living room List of device Open-Stop/Close Impulse Dimmer light RGB/RGBW light Tunable white light On-Off List of groups Ground oor lights List of device Open-Stop/Close Impulse Dimmer light RGB/RGBW light Tunable white light On-Off List of groups Ground oor lights Save zone Save zone Save Recycle bin 19 18 025-FIS18_Smart_GATEWAY 5.4 SCENARIOS

"Scenario" commands, or rather a command which brings the status of various devices to the set value, can be created through the procedure described below. Once created, the scenarios can be recalled by clicking on the dedicated key on the scenario interface; see step 6 of the procedure or create a time setting. Scenario commands are sequential (a command is transmitted to one device at a time). EXAMPLE:

SCENARIO 1: the white lights power OFF and the suffused blue light powers ON PROCEDURE FOR CREATING SCENARIOS STEP1 Click on the scenarios icon. Any created scenarios will be displayed. Scenarios STEP2 Click on the "+" icon. The scenarios creation menu will open. Scenarios

+

Scenarios STEP5 The application returns to the "scenarios" menu and displays the created scenarios. To create more scenarios, return to step 2. STEP4 Enter the name of the scenario (e.g.: power OFF everything) and select the devices involved and their action. Scenari Total Off New scenario Title Total Off Open-Stop/Close Impulse Dimmer light RGB/RGBW light Tunable white light On-Off Save scenario Title Select device See/edit action settings STEP6 To recall the scenario which has been set, press the "Play" icon on the scenarios screen. To create a time setting which automatically activates the scenario at a scheduled time and day; see paragraph 5.5. Scenarios Total Off Play scenario 20 19 025-FIS18_Smart_GATEWAY PROCEDURE TO DELETE OR MODIFY CREATED SCENARIOS If you wish to delete or modify a created scenario, change its name or the actions of the devices, perform the following procedure:

STEP1 Click on the scenarios icon. Any created scenarios will be displayed. Scenari STEP2 Click on the "pencil" icon. The "gear" icon is displayed next to each scenario. Scenarios Total Off Pensil Gear Scenari STEP4 EDIT: modify the values and click on "Save scenario"

DELETE: click on the "recycle bin" icon STEP3 Click on the name of the zone you wish to delete or modify. The settings menu will be displayed, along with the parameter settings. Edit scenario Title Total Off Open-Stop/Close Impulse Dimmer light RGB/RGBW light Tunable white light On-Off Save scenario Save Recycle bin Title Select device See/edit action settings Edit scenario Title Total Off Open-Stop/Close Impulse Dimmer light RGB/RGBW light Tunable white light On-Off Save scenario 21 20 025-FIS18_Smart_GATEWAY 5.5 PROGRAMMING THE TIMER ATTENTION: To operate correctly, the date and time must be set following the procedure in paragraph 4. ATTENTION: in case of power failure you must updated the time manually, where possible, therefore, it is advisable to connect the hub to a UPS. The following procedure is used to create timer settings, meaning the creation of time setting for the automatic transmis-

sion of one or more commands from a scenario at a scheduled time and day of the week. EXAMPLE: time setting 1: the roller shutters open at 7 A.M., from Monday to Friday PROCEDURE FOR CREATING TIMER SETTINGS STEP1 Click on the timer settings icon. Any created settings will be displayed. STEP2 Click on the "+" icon. The timer settings creation menu will open. Time setting Time setting

+

Time setting STEP4 Click on the "clock" icon. New time setting Title Wake Up List of devices Open-Stop/Close 1 Open-Stop/Close 2 Luce Dimmer Luce RGB/RGBW Luce Bianco dinamico On-Off Time setting Save Clock icon STEP3 Enter the name of the timer setting (e.g.: morning wake up) and select the devices involved and their action. New time setting Title Wake Up List of devices Open-Stop/Close 1 Open-Stop/Close 2 Luce Dimmer Luce RGB/RGBW Luce Bianco dinamico On-Off Time setting Save Title Device setting See/edit action settings STEP5 Set the time and the days you wish the action to be performed and click on the "OK" key to conrm. STEP6 The application returns to the "timer settings" menu. To create other settings, return to step 2. Timer settings can be activated/deactivated. Hour:

scroll through the hours and minutes and click on the selected value Time setting Wake Up Days:

Select the days of the week

"OK" key When min 20 21 22 h 11 12 13 Monday Tuesday Thursday Friday Wednesday Saturday Sunday OK 21 Activate/Deactivate timer setting 22 025-FIS18_Smart_GATEWAY NOTE

- If you wish to create events which automatically activate and deactivate (e.g.: the lights power ON at a set time and power OFF at a later time), create two timer settings.

- Once created, the settings can be activated and deactivated by clicking on the dedicated key on the on the timer settings interface; see step 6 of the procedure.

- the commands transmitted by the hub are sequential (e.g.: if the action consists of powering OFF three lights, they will be powered OFF one at a time). PROCEDURE TO DELETE OR MODIFY CREATED TIMER SETTINGS If you wish to delete or modify created timer settings, change its name, the actions of the devices or the automatic time settings, perform the following procedure:

STEP1 Click on the timer settings icon. Any created settings will be displayed. STEP2 Click on the "pencil" icon. The "gear"

icon is displayed next to each setting. Time setting Time setting Wake Up Gear Programming the timer STEP4 EDIT: modify the values and click on "Save"

DELETE: click on the "recycle bin" icon STEP3 Click on the name of the setting you wish to delete or modify. The settings menu will be displayed, along with the parameter settings. New time setting Title Wake Up List of devices Open-Stop/Close 1 Open-Stop/Close 2 Luce Dimmer Luce RGB/RGBW Luce Bianco dinamico On-Off Time setting Save Title Device setting See/edit action settings New time setting Titolo Wake Up List of devices Open-Stop/Close 1 Open-Stop/Close 2 Luce Dimmer Luce RGB/RGBW Luce Bianco dinamico On-Off Time setting Save 23 22 025-FIS18_Smart_GATEWAY 6 - FURTHER DETAILS 6.1 CREATING A QUICK ACCESS COMMAND The creation of a quick access command for the application makes it easier to use. The procedure differs depending on the type of device in use. Several examples are described below:

ANDROID 1 - Start up Chrome for Android and open the application page according to the settings in paragraph 2 2 - Click on the "Menu" button in Chrome, then click on "add to home screen". 3 - Give the link a name and Chrome will then add it to the homepage. Almost all other Android compatible browsers have this feature; in Firefox for Android, for example, simply click on the menu button, then Page, and Add to Home. IPHONE, IPAD, AND IPOD TOUCH 1 - Start up Safari on the Apple iOS and open the application page according to the settings in paragraph 2 2 - Click on the Share button in the toolbar of the browser (the rectangle with an arrow facing upwards which is located in the upper part of an iPad display, and in the lower part of an iPhone or iPod Touch display) and click on "Add to Home"

3 - You will be requested to assign a name to the link before clicking the Add button. Other browsers, such as Chrome for iOS, do not have this function due to the limitations of iOS. WINDOWS 1 - Start up Chrome and open the application page according to the settings in paragraph 2 2 - Click on the options icon (the three dots located at the top of the display, to the right of the address bar), click on More tools, then click "Add to desktop". With Internet Explorer, simply click on the settings icon (the gear icon located at the top of the display, to the right of the address bar), then click on "Add site to Start menu". 23 24 025-FIS18_Smart_GATEWAY 6.2 VERIFY THE NETWORK IP ADDRESS Using a Smartphone connected to the existing network, the IP address of your network can be displayed. ANDROID 1 - Open the settings menu to view the available network connections 2 - Verify you are connected to the network for which you want to know the address, then click on the network name to display the information 3 - Display the "IP Address"

When the hub is connecting, the IP address which contains the same rst three numbers as those displayed, and the

nal modied number, must be used (see the example). If you do not know an available address to enter as the nal number, try using numbers from 150 to 250. EXAMPLE:

IP address displayed:

IP address to enter in the hub:

192.168.1.6 192.168.1.200 IPHONE, IPAD, E IPOD TOUCH 1 - Open the settings menu to view the available network connections 2 - Verify you are connected to the network for which you want to know the address, then click on the "info" icon to the right of the network name 3 - Scroll through the menu until "IP Address" is displayed When the hub is connecting, the IP address which contains the same rst three numbers as those displayed, and the

nal modied number, must be used (see the example). If you do not know an available address to enter as the nal number, try using numbers from 150 to 250. EXAMPLE:

IP address displayed:

IP address to enter in the hub:

192.168.1.6 192.168.1.200 25 24 025-FIS18_Smart_GATEWAY 7 - RESET THE SYSTEM 7.1 RESET THE NETWORK CONFIGURATION This procedure deletes the network congurations set under paragraph 2, then the hub restarts in hotspot mode with the default passwords. The default password to access the network and system conguration will also be reset. NOTE: any devices groups, zones, scenarios and timer settings will be deleted STEP1 Press and hold the reset key until the LED begins to ash STEP2 Press and release the key again. The LED ashes quickly and powers OFF RESET KEY RESET KEY PRESS FOR 8 SECONDS SHORT PRESS Following this procedure, the values will be those indicated in the procedures from paragraph 2 and 3 of this manual. 25 26 025-FIS18_Smart_GATEWAY 7.2 RESET THE SYSTEM CONFIGURATION This procedure deletes any devices, groups, zones, scenarios and timer settings. STEP1 Access the application according to the network conguration performed in paragraph 2 STEP2 Click on "menu". STEP3 Click on "Congure system"

menu Devices Congure system Devices Settings Congure network Congure system STEP6 Click on Reset STEP5 Click on "Reset"

STEP4*

You will be requested to enter a password; the default password is: 1234. 1234 Password Enter password Conrm Cancel Reset Congura impianto LISTA DISPOSITIVI LISTA GRUPPI RESET Reset Impianto Delete all Devices, Groups, Zones, Scenarios and Time settings?

Reset Reset STEP7 The system will be restored Reset system System restored ATTENZIONE In step 4 of the procedure, the default values to be used will be suggested. If these were modied previously and cannot be recovered, the system must be reset; see paragraph 7.1. A reset will not delete systems created in the interface (see paragraph 3); it will only reset the network settings (network name, page address, password). The default password from "step 4" can be changed by accessing "menu-set-

tings-change password". 27 26 025-FIS18_Smart_GATEWAY FCC NOTE:

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. NOTE: THE GRANTEE IS NOT RESPONSIBLE FOR ANY CHANGES OR MODIFICATIONS NOT EXPRESSLY APPROVED BY THE PARTY RESPONSIBLE FOR COMPLIANCE. SUCH MODIFICATIONS COULD VOID THE USERS AUTHORITY TO OPERATE THE EQUIPMENT. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

-- Reorient or relocate the receiving antenna.

-- Increase the separation between the equipment and receiver.

-- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

-- Consult the dealer or an experienced radio/TV technician for help. The device has been evaluated to meet general RF exposure environment. To maintain compliance with FCC's RF exposure guidelines, the distance must be at least 20cm between the radiator and your body, and fully supported by the operating and installation configurations of the transmitter and its antenna. WARNING Save these instructions.The instructions for use must be scrupulously complied with during installation and use. TECHNICAL DATA

- Rating for protection against dust, solid objects and moisture: IP20 (Standard Ref. EN 60529 EN 60598-1) KEY TO SYMBOLS (for EUROPE) Appliance in class III. The power appliance must be very low voltage security. Use only power supplies guaranteed SELV or SELV equivalent. (Standard Ref. EN 61347-2-13). DEMOLITION AND DISPOSAL OF THE LIGHTING APPLIANCE The appliance should be considered as EEE (electrical and electronic equipment) and must be disposed of as such. The symbol shown below indicates that at the end of its life the equipment is to be considered WEEE (waste electrical and electronic equipment). As such the appliance may not be disposed of as mixed municipal waste, but must be taken to the special collection centres set up by the local authorities or by the manufacturers, who will arrange for the separate collection of WEEE. When purchasing a new appliance, an old appliance to be disposed of may also be handed over to the distributor. Contact the competent authorities or the distributor/manufacturer for further information on the matter. MAINTENANCE In case of failure, replace the whole set. 025-FIS18_Smart_GATEWAY 28

Reference No.: WTF19F01003151W Page 1 of 2 Test Setup For Radiated Emission (30MHz to 1GHz) Test Setup For Radiated Emission (Above 1GHz) Waltek Services (Foshan) Co.,Ltd. http://www.waltek.com.cn Reference No.: WTF19F01003151W Page 2 of 2 Test Setup For Conducted Emission Waltek Services (Foshan) Co.,Ltd. http://www.waltek.com.cn