all | frequencies |
|
exhibits | applications |
---|---|---|---|---|
manual |
app s | submitted / available | |||||||
---|---|---|---|---|---|---|---|---|
1 |
|
Exhibit D Users Manual per 2 1033 b3 | Users Manual | 757.92 KiB | November 02 2009 | |||
1 | Cover Letter(s) | November 02 2009 | ||||||
1 | Cover Letter(s) | November 02 2009 | ||||||
1 | ID Label/Location Info | November 02 2009 | ||||||
1 | External Photos | November 02 2009 | ||||||
1 | Internal Photos | November 02 2009 | ||||||
1 | Test Setup Photos | November 02 2009 | ||||||
1 | Test Report | November 02 2009 |
1 | Exhibit D Users Manual per 2 1033 b3 | Users Manual | 757.92 KiB | November 02 2009 |
Thank you for buying a PocketWizard MiniTT1/FlexTT5 system for Canon DSLR E-TTL cameras and ashes. To help you get started please read this quick guide and familiarize yourself with the system. Check www.PocketWizard.com for the latest rmware and full user manual, as well as the PocketWizard Utility which enables setting additional features for your ControlTL radio slave. Quick Guide MiniTT1/FlexTT5 for Canon 340 354 MHz, US FCC/IC MiniTT1 Internal Antenna Conguration/Channel 1 Conguration/Channel 2 Power Off TEST/LEARN Button Status LED Battery Compartment
(on bottom) USB Connector
(under rubber cover) Canon-style Hot Shoe with Pass Through Locking Ring
(on bottom foot) FlexTT5 USB Connector (behind antenna) Adjustable Antenna Zone Selector Conguration/Channel 1 Conguration/Channel 2 Power Off TEST/LEARN Button Remote Studio or other ash Triggering Port Remote Camera Triggering Port Lanyard Loop Battery Compartment
(2 AA [IEC:LR6]) 1/4-20 mount
(on bottom) Canon-style Hot Shoe with Pass Through Locking Ring
(on bottom foot) Status LED MAKE IT POSSIBLE READ ME FIRST:
All equipment should be turned OFF when making connections. Unwanted triggering may occur. First exposure after making initial connections/powering on may not be properly exposed. First shot is a camera calibrations shot. Always test twice. Review product manuals for your camera/flash system. For most basic functions when using Canons system or PocketWizards, operation is identical. You may use a FlexTT5 as a transmitter instead of a MiniTT1 in all scenarios. Make sure all PocketWizard units are set to same PocketWizard Channel. PocketWizard Channel is used instead of Canon channel. See LEARN Mode section. E-TTL Basic Wireless E-TTL: MiniTT1 FlexTT5 No ash on Camera 1. Slide MiniTT1 Transmitter onto camera. 2. Slide remote Speedlite onto FlexTT5 Transceiver. Repeat for each remote Speedlite. All remote E-TTL ashes will be treated as one zone of light. 3. Make sure all your PocketWizard units are on the same Channel and trigger normally. This mode is like using Canon ST-E2 (non-ratio mode) or 580EX (I or II, master mode, main ash off, non-ratio) in camera shoe. Basic Wireless E-TTL: MiniTT1 FlexTT5 Flash on Camera 1. Slide MiniTT1 Transmitter onto camera. 2. Slide Canon 580EX Speedlite onto MiniTT1 unit. Set for MASTER = ON. 3. Slide remote Speedlite onto FlexTT5 Transceiver. Repeat for each remote Speedlite. All remote E-TTL ashes will be treated as one zone of light. 4. Make sure all your PocketWizard units are on the same Channel and trigger normally. Ratio Wireless E-TTL: MiniTT1 FlexTT5 Flash on Camera 1. Slide MiniTT1 Transmitter onto camera. 2. Slide Canon 580EX Speedlite onto MiniTT1 unit. Set for MASTER = ON. Enable Zones per ash instructions. Canon Speedlite Transmitter ST-E2 may also be used. 3. Set remote FlexTT5 unit to desired Canon Ratio Zone (A, B, C) using FlexTT5 Zone Switch. 4. Slide remote Speedlite onto FlexTT5 Transceiver. Set for regular E-TTL mode (not SLAVE or MASTER). Repeat for each remote Speedlite. All remote E-TTL ashes on same FlexTT5 Zone will be treated as one zone of light. 5. Adjust ratios using MASTER Speedlite ash controls. 6. Make sure all your PocketWizard units are on the same Channel and trigger normally. Setting Canon E-TTL to normal ash (WIRELESS = OFF) when in shoe of MiniTT1 will disable all remote ash. This operation mirrors Canon functionality. IMPORTANT: Canon ash units set to SLAVE = ON and connected to FlexTT5 units will have slave mode automatically turned off, but will still function as slaves correctly. Set desired Canon Ratio Zone via remote FlexTT5 Zone Switch. PocketWizard Channel is used instead of Canon channel. ISO, aperture, ash exposure compensation (FEC), and other settings will track exposure normally when E-TTL via the PocketWizard ControlTL system. Thank you for purchasing a PocketWizard product, the most advanced photographic wireless control system available. To get the most out of your new product spend some time on www.PocketWizard.com where you will find information on all aspects of your new PocketWizard. Specifically, our Support page contains some vital information and tools for your new PocketWizard. www.pocketwizard.com/support/
CONFIGURATION:
Your new PocketWizard runs on very sophisticated software we call ControlTL. This software can be configured to your specific needs using a PocketWizard Utility program that can be downloaded online. REGISTRATION:
ControlTL software is designed to be Future Proof and will be upgraded from time-to-time. Please register your product online to be notified when updates are available. MANUALS:
Included in the box is a Quick Guide to get you going fast. For the complete story, there is an in-depth manual that can be read or downloaded online. MAKE IT POSSIBLE Have fun pushing the boundaries of your creativity!
The FCC wants you to know:
WARNING Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy, and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
1. Reorient or relocate the receiving antenna. 2. Increase the separation between the equipment and the receiver. 3. Consult the dealer or an experienced radio or television technician for help. This device complies with Part 15 of the FCC rules and also with RSS-210 of Industry Canada. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. MiniTT1 FCC ID Number: KDS-PW3-004 FlexTT5 FCC ID Number: KDS-PW3-005 MiniTT1 CANADA IC: 2170A-PW3004 FlexTT5 CANADA IC: 2170A-PW3005 V1.0 January 2009 LPF395 MAKE IT POSSIBLE Thank you for buying a PocketWizard MiniTT1/FlexTT5 system for Canon DSLR E-TTL cameras and ashes. To help you get started please read this quick guide and familiarize yourself with the system. Check www.PocketWizard.com for the latest rmware and full user manual, as well as the PocketWizard Utility which enables setting additional features for your ControlTL radio slave. Quick Guide MiniTT1/FlexTT5 for Canon 340 354 MHz, US FCC/IC MiniTT1 Internal Antenna Conguration/Channel 1 Conguration/Channel 2 Power Off TEST/LEARN Button Status LED Battery Compartment
(on bottom) USB Connector
(under rubber cover) Canon-style Hot Shoe with Pass Through Locking Ring
(on bottom foot) FlexTT5 USB Connector (behind antenna) Adjustable Antenna Zone Selector Conguration/Channel 1 Conguration/Channel 2 Power Off TEST/LEARN Button Remote Studio or other ash Triggering Port Remote Camera Triggering Port Lanyard Loop Battery Compartment
(2 AA [IEC:LR6]) 1/4-20 mount
(on bottom) Canon-style Hot Shoe with Pass Through Locking Ring
(on bottom foot) Status LED MAKE IT POSSIBLE READ ME FIRST:
All equipment should be turned OFF when making connections. Unwanted triggering may occur. First exposure after making initial connections/powering on may not be properly exposed. First shot is a camera calibrations shot. Always test twice. Review product manuals for your camera/flash system. For most basic functions when using Canons system or PocketWizards, operation is identical. You may use a FlexTT5 as a transmitter instead of a MiniTT1 in all scenarios. Make sure all PocketWizard units are set to same PocketWizard Channel. PocketWizard Channel is used instead of Canon channel. See LEARN Mode section. E-TTL Basic Wireless E-TTL: MiniTT1 FlexTT5 No ash on Camera 1. Slide MiniTT1 Transmitter onto camera. 2. Slide remote Speedlite onto FlexTT5 Transceiver. Repeat for each remote Speedlite. All remote E-TTL ashes will be treated as one zone of light. 3. Make sure all your PocketWizard units are on the same Channel and trigger normally. This mode is like using Canon ST-E2 (non-ratio mode) or 580EX (I or II, master mode, main ash off, non-ratio) in camera shoe. Basic Wireless E-TTL: MiniTT1 FlexTT5 Flash on Camera 1. Slide MiniTT1 Transmitter onto camera. 2. Slide Canon 580EX Speedlite onto MiniTT1 unit. Set for MASTER = ON. 3. Slide remote Speedlite onto FlexTT5 Transceiver. Repeat for each remote Speedlite. All remote E-TTL ashes will be treated as one zone of light. 4. Make sure all your PocketWizard units are on the same Channel and trigger normally. Ratio Wireless E-TTL: MiniTT1 FlexTT5 Flash on Camera 1. Slide MiniTT1 Transmitter onto camera. 2. Slide Canon 580EX Speedlite onto MiniTT1 unit. Set for MASTER = ON. Enable Zones per ash instructions. Canon Speedlite Transmitter ST-E2 may also be used. 3. Set remote FlexTT5 unit to desired Canon Ratio Zone (A, B, C) using FlexTT5 Zone Switch. 4. Slide remote Speedlite onto FlexTT5 Transceiver. Set for regular E-TTL mode (not SLAVE or MASTER). Repeat for each remote Speedlite. All remote E-TTL ashes on same FlexTT5 Zone will be treated as one zone of light. 5. Adjust ratios using MASTER Speedlite ash controls. 6. Make sure all your PocketWizard units are on the same Channel and trigger normally. Setting Canon E-TTL to normal ash (WIRELESS = OFF) when in shoe of MiniTT1 will disable all remote ash. This operation mirrors Canon functionality. IMPORTANT: Canon ash units set to SLAVE = ON and connected to FlexTT5 units will have slave mode automatically turned off, but will still function as slaves correctly. Set desired Canon Ratio Zone via remote FlexTT5 Zone Switch. PocketWizard Channel is used instead of Canon channel. ISO, aperture, ash exposure compensation (FEC), and other settings will track exposure normally when E-TTL via the PocketWizard ControlTL system. Thank you for buying a PocketWizard MiniTT1/FlexTT5 system for Canon DSLR E-TTL cameras and ashes. To help you get started please read this quick guide and familiarize yourself with the system. Check www.PocketWizard.com for the latest rmware and full user manual, as well as the PocketWizard Utility which enables setting additional features for your ControlTL radio slave. Quick Guide MiniTT1/FlexTT5 for Canon 340 354 MHz, US FCC/IC MiniTT1 Internal Antenna Conguration/Channel 1 Conguration/Channel 2 Power Off TEST/LEARN Button Status LED Battery Compartment
(on bottom) USB Connector
(under rubber cover) Canon-style Hot Shoe with Pass Through Locking Ring
(on bottom foot) FlexTT5 USB Connector (behind antenna) Adjustable Antenna Zone Selector Conguration/Channel 1 Conguration/Channel 2 Power Off TEST/LEARN Button Remote Studio or other ash Triggering Port Remote Camera Triggering Port Lanyard Loop Battery Compartment
(2 AA [IEC:LR6]) 1/4-20 mount
(on bottom) Canon-style Hot Shoe with Pass Through Locking Ring
(on bottom foot) Status LED MAKE IT POSSIBLE READ ME FIRST:
All equipment should be turned OFF when making connections. Unwanted triggering may occur. First exposure after making initial connections/powering on may not be properly exposed. First shot is a camera calibrations shot. Always test twice. Review product manuals for your camera/flash system. For most basic functions when using Canons system or PocketWizards, operation is identical. You may use a FlexTT5 as a transmitter instead of a MiniTT1 in all scenarios. Make sure all PocketWizard units are set to same PocketWizard Channel. PocketWizard Channel is used instead of Canon channel. See LEARN Mode section. E-TTL Basic Wireless E-TTL: MiniTT1 FlexTT5 No ash on Camera 1. Slide MiniTT1 Transmitter onto camera. 2. Slide remote Speedlite onto FlexTT5 Transceiver. Repeat for each remote Speedlite. All remote E-TTL ashes will be treated as one zone of light. 3. Make sure all your PocketWizard units are on the same Channel and trigger normally. This mode is like using Canon ST-E2 (non-ratio mode) or 580EX (I or II, master mode, main ash off, non-ratio) in camera shoe. Basic Wireless E-TTL: MiniTT1 FlexTT5 Flash on Camera 1. Slide MiniTT1 Transmitter onto camera. 2. Slide Canon 580EX Speedlite onto MiniTT1 unit. Set for MASTER = ON. 3. Slide remote Speedlite onto FlexTT5 Transceiver. Repeat for each remote Speedlite. All remote E-TTL ashes will be treated as one zone of light. 4. Make sure all your PocketWizard units are on the same Channel and trigger normally. Ratio Wireless E-TTL: MiniTT1 FlexTT5 Flash on Camera 1. Slide MiniTT1 Transmitter onto camera. 2. Slide Canon 580EX Speedlite onto MiniTT1 unit. Set for MASTER = ON. Enable Zones per ash instructions. Canon Speedlite Transmitter ST-E2 may also be used. 3. Set remote FlexTT5 unit to desired Canon Ratio Zone (A, B, C) using FlexTT5 Zone Switch. 4. Slide remote Speedlite onto FlexTT5 Transceiver. Set for regular E-TTL mode (not SLAVE or MASTER). Repeat for each remote Speedlite. All remote E-TTL ashes on same FlexTT5 Zone will be treated as one zone of light. 5. Adjust ratios using MASTER Speedlite ash controls. 6. Make sure all your PocketWizard units are on the same Channel and trigger normally. Setting Canon E-TTL to normal ash (WIRELESS = OFF) when in shoe of MiniTT1 will disable all remote ash. This operation mirrors Canon functionality. IMPORTANT: Canon ash units set to SLAVE = ON and connected to FlexTT5 units will have slave mode automatically turned off, but will still function as slaves correctly. Set desired Canon Ratio Zone via remote FlexTT5 Zone Switch. PocketWizard Channel is used instead of Canon channel. ISO, aperture, ash exposure compensation (FEC), and other settings will track exposure normally when E-TTL via the PocketWizard ControlTL system. Thank you for buying a PocketWizard MiniTT1/FlexTT5 system for Canon DSLR E-TTL cameras and ashes. To help you get started please read this quick guide and familiarize yourself with the system. Check www.PocketWizard.com for the latest rmware and full user manual, as well as the PocketWizard Utility which enables setting additional features for your ControlTL radio slave. Quick Guide MiniTT1/FlexTT5 for Canon 340 354 MHz, US FCC/IC MiniTT1 Internal Antenna Conguration/Channel 1 Conguration/Channel 2 Power Off TEST/LEARN Button Status LED Battery Compartment
(on bottom) USB Connector
(under rubber cover) Canon-style Hot Shoe with Pass Through Locking Ring
(on bottom foot) FlexTT5 USB Connector (behind antenna) Adjustable Antenna Zone Selector Conguration/Channel 1 Conguration/Channel 2 Power Off TEST/LEARN Button Remote Studio or other ash Triggering Port Remote Camera Triggering Port Lanyard Loop Battery Compartment
(2 AA [IEC:LR6]) 1/4-20 mount
(on bottom) Canon-style Hot Shoe with Pass Through Locking Ring
(on bottom foot) Status LED MAKE IT POSSIBLE READ ME FIRST:
All equipment should be turned OFF when making connections. Unwanted triggering may occur. First exposure after making initial connections/powering on may not be properly exposed. First shot is a camera calibrations shot. Always test twice. Review product manuals for your camera/flash system. For most basic functions when using Canons system or PocketWizards, operation is identical. You may use a FlexTT5 as a transmitter instead of a MiniTT1 in all scenarios. Make sure all PocketWizard units are set to same PocketWizard Channel. PocketWizard Channel is used instead of Canon channel. See LEARN Mode section. E-TTL Basic Wireless E-TTL: MiniTT1 FlexTT5 No ash on Camera 1. Slide MiniTT1 Transmitter onto camera. 2. Slide remote Speedlite onto FlexTT5 Transceiver. Repeat for each remote Speedlite. All remote E-TTL ashes will be treated as one zone of light. 3. Make sure all your PocketWizard units are on the same Channel and trigger normally. This mode is like using Canon ST-E2 (non-ratio mode) or 580EX (I or II, master mode, main ash off, non-ratio) in camera shoe. Basic Wireless E-TTL: MiniTT1 FlexTT5 Flash on Camera 1. Slide MiniTT1 Transmitter onto camera. 2. Slide Canon 580EX Speedlite onto MiniTT1 unit. Set for MASTER = ON. 3. Slide remote Speedlite onto FlexTT5 Transceiver. Repeat for each remote Speedlite. All remote E-TTL ashes will be treated as one zone of light. 4. Make sure all your PocketWizard units are on the same Channel and trigger normally. Ratio Wireless E-TTL: MiniTT1 FlexTT5 Flash on Camera 1. Slide MiniTT1 Transmitter onto camera. 2. Slide Canon 580EX Speedlite onto MiniTT1 unit. Set for MASTER = ON. Enable Zones per ash instructions. Canon Speedlite Transmitter ST-E2 may also be used. 3. Set remote FlexTT5 unit to desired Canon Ratio Zone (A, B, C) using FlexTT5 Zone Switch. 4. Slide remote Speedlite onto FlexTT5 Transceiver. Set for regular E-TTL mode (not SLAVE or MASTER). Repeat for each remote Speedlite. All remote E-TTL ashes on same FlexTT5 Zone will be treated as one zone of light. 5. Adjust ratios using MASTER Speedlite ash controls. 6. Make sure all your PocketWizard units are on the same Channel and trigger normally. Setting Canon E-TTL to normal ash (WIRELESS = OFF) when in shoe of MiniTT1 will disable all remote ash. This operation mirrors Canon functionality. IMPORTANT: Canon ash units set to SLAVE = ON and connected to FlexTT5 units will have slave mode automatically turned off, but will still function as slaves correctly. Set desired Canon Ratio Zone via remote FlexTT5 Zone Switch. PocketWizard Channel is used instead of Canon channel. ISO, aperture, ash exposure compensation (FEC), and other settings will track exposure normally when E-TTL via the PocketWizard ControlTL system. Thank you for buying a PocketWizard MiniTT1/FlexTT5 system for Canon DSLR E-TTL cameras and ashes. To help you get started please read this quick guide and familiarize yourself with the system. Check www.PocketWizard.com for the latest rmware and full user manual, as well as the PocketWizard Utility which enables setting additional features for your ControlTL radio slave. Quick Guide MiniTT1/FlexTT5 for Canon 340 354 MHz, US FCC/IC MiniTT1 Internal Antenna Conguration/Channel 1 Conguration/Channel 2 Power Off TEST/LEARN Button Status LED Battery Compartment
(on bottom) USB Connector
(under rubber cover) Canon-style Hot Shoe with Pass Through Locking Ring
(on bottom foot) FlexTT5 USB Connector (behind antenna) Adjustable Antenna Zone Selector Conguration/Channel 1 Conguration/Channel 2 Power Off TEST/LEARN Button Remote Studio or other ash Triggering Port Remote Camera Triggering Port Lanyard Loop Battery Compartment
(2 AA [IEC:LR6]) 1/4-20 mount
(on bottom) Canon-style Hot Shoe with Pass Through Locking Ring
(on bottom foot) Status LED MAKE IT POSSIBLE READ ME FIRST:
All equipment should be turned OFF when making connections. Unwanted triggering may occur. First exposure after making initial connections/powering on may not be properly exposed. First shot is a camera calibrations shot. Always test twice. Review product manuals for your camera/flash system. For most basic functions when using Canons system or PocketWizards, operation is identical. You may use a FlexTT5 as a transmitter instead of a MiniTT1 in all scenarios. Make sure all PocketWizard units are set to same PocketWizard Channel. PocketWizard Channel is used instead of Canon channel. See LEARN Mode section. E-TTL Basic Wireless E-TTL: MiniTT1 FlexTT5 No ash on Camera 1. Slide MiniTT1 Transmitter onto camera. 2. Slide remote Speedlite onto FlexTT5 Transceiver. Repeat for each remote Speedlite. All remote E-TTL ashes will be treated as one zone of light. 3. Make sure all your PocketWizard units are on the same Channel and trigger normally. This mode is like using Canon ST-E2 (non-ratio mode) or 580EX (I or II, master mode, main ash off, non-ratio) in camera shoe. Basic Wireless E-TTL: MiniTT1 FlexTT5 Flash on Camera 1. Slide MiniTT1 Transmitter onto camera. 2. Slide Canon 580EX Speedlite onto MiniTT1 unit. Set for MASTER = ON. 3. Slide remote Speedlite onto FlexTT5 Transceiver. Repeat for each remote Speedlite. All remote E-TTL ashes will be treated as one zone of light. 4. Make sure all your PocketWizard units are on the same Channel and trigger normally. Ratio Wireless E-TTL: MiniTT1 FlexTT5 Flash on Camera 1. Slide MiniTT1 Transmitter onto camera. 2. Slide Canon 580EX Speedlite onto MiniTT1 unit. Set for MASTER = ON. Enable Zones per ash instructions. Canon Speedlite Transmitter ST-E2 may also be used. 3. Set remote FlexTT5 unit to desired Canon Ratio Zone (A, B, C) using FlexTT5 Zone Switch. 4. Slide remote Speedlite onto FlexTT5 Transceiver. Set for regular E-TTL mode (not SLAVE or MASTER). Repeat for each remote Speedlite. All remote E-TTL ashes on same FlexTT5 Zone will be treated as one zone of light. 5. Adjust ratios using MASTER Speedlite ash controls. 6. Make sure all your PocketWizard units are on the same Channel and trigger normally. Setting Canon E-TTL to normal ash (WIRELESS = OFF) when in shoe of MiniTT1 will disable all remote ash. This operation mirrors Canon functionality. IMPORTANT: Canon ash units set to SLAVE = ON and connected to FlexTT5 units will have slave mode automatically turned off, but will still function as slaves correctly. Set desired Canon Ratio Zone via remote FlexTT5 Zone Switch. PocketWizard Channel is used instead of Canon channel. ISO, aperture, ash exposure compensation (FEC), and other settings will track exposure normally when E-TTL via the PocketWizard ControlTL system. www.pocketwizard.com LEARN Mode Manual Flash Other Functions Specications Trigger Delay = 0 seconds fast as a wire Batteries: MiniTT1 = CR2450 or CR2354 (100s of hours) Maximum FPS: Up to 12 (varies with camera, E-TTL usage reduces FPS) E-TTL: E-TTL I & E-TTL II (DSLR only, not for lm TTL) Operating Temperature: Above -15 C (5 F) and below 50 C (120 F) Storage Temperature (without battery): Above -30 C (-22 F) and below 85 C (185 F) FlexTT5 = 2 x AA (IEC:LR6) (60 hours) Powerable via USB AC adapter (powering from computer USB port not recommended) This US FCC/Canada IC frequency PocketWizard radio slave is compatible with all US frequency PocketWizard products. It is not frequency compatible with CE or JAPAN PocketWizard products. Verify frequency compatibility before purchasing. 2009 LPA Design, Inc. All rights reserved. Product features and specications are subject to change without notice. PocketWizard, ControlTL, MiniTT1, FlexTT5, HyperSync, ZeroSync, Plus II and MultiMAX are either trademarks or registered trademarks of LPA Design, Inc. All other trademarks contained herein are the property of their respective owners. US Patent: 5,359,375 and Patents Pending V1.0 January 2009 LPF374 For more information on this product, including detailed features, specications and the complete user manual, go to www.pocketwizard.com. This product is covered under a warranty. For more information on the warranty and to register your product, please go to www.pocketwizard.com/support. MAKE IT POSSIBLE Channels can be taught via PocketWizard Utility or from any PocketWizard Transmitter using LEARN mode:
IMPORTANT: Hold units at least 2 feet apart when teaching/learning. 1. Turn MiniTT1 or FlexTT5 unit ON and select Channel to be taught. 2. Press and hold TEST for several seconds until LED blinks amber, then release TEST. 3. Quickly press and hold TEST on teaching Transmitting unit (MiniTT1, FlexTT5, Plus II or MultiMAX). When LED blinks green, channel is learned. Connected ash may 1 green blink = Low Legacy Channel learned (1 through 16) 2 green blinks = High Legacy Channel learned (MultiMAX 17 through 32) 3 green blinks = ControlTL Channel learned (ControlTL 1 through 20) trigger during LEARN. For remote TTL systems, teach MiniTT1 unit to be used as primary transmitter rst, then use it to teach all FlexTT5 units. MiniTT1 and FlexTT5 units send out both ControlTL and Legacy triggers every time they are triggered. For remote TTL to function, ControlTL channel must be learned. If you see only 1 or 2 green blinks, and you desire TTL, teach again with MiniTT1 or FlexTT5 unit. Look for 3 green blinks to verify ControlTL is learned. To teach all units Legacy channels, use Legacy Transmitter as teaching unit for all learning units, including MiniTT1 unit to be used as primary transmitter. To avoid inadvertent ashing from remote units that have already been taught or have already had channel set, turn them OFF. MiniTT1 Plus II, MultiMAX, Integrated, or FlexTT5 connected to manual ash Remote ash with or without TTL ash on camera 1. Slide MiniTT1 Transmitter onto camera. 2. If desired, slide Canon E-TTL Speedlite (MASTER = ON) onto MiniTT1 unit. 3. Make sure all your PocketWizard units are on the same Channel and trigger normally. Note: Manual remote ashes are not calculated as part of the E-TTL exposure. Be sure to set on-camera FEC if remote ash is illuminating same subject as your E-TTL ash. ZeroSync occurs automatically. Trigger as fast as a wire with all PocketWizard radios. Use PocketWizard Utility to engage HyperSync and explore faster than X-sync shutter speeds. See user manual at www.pocketwizard.com for more information. Auto-Relay Mode A FlexTT5 unit in cameras shoe and connected with motor drive cord to P1 can receive a radio trigger, trigger the cameras motor drive which in turn triggers a remote ash. The channel used for relay transmit is 1 higher than taught channel, unless set via PocketWizard Utility. Example: if you taught FlexTT5 unit Channel 3 then relay transmit occurs on Channel 4. Press TEST on hand-held trigger unit to begin relay sequence. RESET to Default Settings RESET A: To reset Learned Channels, hold TEST on power up. LED blinks green twice to indicate reset. Release TEST. Advanced Features set via USB are retained. A: Default Channels C1 = ControlTL Channel 1, Legacy Channel 1 C2 = ControlTL Channel 2, Legacy Channel 2 Green Good battery Amber Warning battery low Red Status LED Normal waiting for trigger operation = short blink every 2 seconds. Normal short blink color indicates Battery Level:
Steady red LED in sync with TEST indicates normal transmission.
(Hold for 10 seconds to teach see LEARN mode) Short red blink in sync with trigger indicates normal reception. Rapid red blinking when not triggering or half-pressing camera indicates error condition. Power off the unit, reseat all connections, and power back on. Very low battery change immediately RESET A & B: To reset all Advanced Features and Learned Channels to FACTORY DEFAULTS, hold TEST on power up for longer than 10 seconds. When LED blinks green 4 times, release. B: Default Advanced Features Auto ISO and Aperture Tracking Enabled Exposure Compensation Center Value = 3.5 HyperSync Offset = -250 microseconds Remote TTL Flash Sleep Mode = Disabled Camera Model = Auto All settings may be congured using the PocketWizard Utility available from www.pocketwizard.com www.pocketwizard.com LEARN Mode Manual Flash Other Functions Specications Trigger Delay = 0 seconds fast as a wire Batteries: MiniTT1 = CR2450 or CR2354 (100s of hours) Maximum FPS: Up to 12 (varies with camera, E-TTL usage reduces FPS) E-TTL: E-TTL I & E-TTL II (DSLR only, not for lm TTL) Operating Temperature: Above -15 C (5 F) and below 50 C (120 F) Storage Temperature (without battery): Above -30 C (-22 F) and below 85 C (185 F) FlexTT5 = 2 x AA (IEC:LR6) (60 hours) Powerable via USB AC adapter (powering from computer USB port not recommended) This US FCC/Canada IC frequency PocketWizard radio slave is compatible with all US frequency PocketWizard products. It is not frequency compatible with CE or JAPAN PocketWizard products. Verify frequency compatibility before purchasing. 2009 LPA Design, Inc. All rights reserved. Product features and specications are subject to change without notice. PocketWizard, ControlTL, MiniTT1, FlexTT5, HyperSync, ZeroSync, Plus II and MultiMAX are either trademarks or registered trademarks of LPA Design, Inc. All other trademarks contained herein are the property of their respective owners. US Patent: 5,359,375 and Patents Pending V1.0 January 2009 LPF374 For more information on this product, including detailed features, specications and the complete user manual, go to www.pocketwizard.com. This product is covered under a warranty. For more information on the warranty and to register your product, please go to www.pocketwizard.com/support. MAKE IT POSSIBLE Channels can be taught via PocketWizard Utility or from any PocketWizard Transmitter using LEARN mode:
IMPORTANT: Hold units at least 2 feet apart when teaching/learning. 1. Turn MiniTT1 or FlexTT5 unit ON and select Channel to be taught. 2. Press and hold TEST for several seconds until LED blinks amber, then release TEST. 3. Quickly press and hold TEST on teaching Transmitting unit (MiniTT1, FlexTT5, Plus II or MultiMAX). When LED blinks green, channel is learned. Connected ash may 1 green blink = Low Legacy Channel learned (1 through 16) 2 green blinks = High Legacy Channel learned (MultiMAX 17 through 32) 3 green blinks = ControlTL Channel learned (ControlTL 1 through 20) trigger during LEARN. For remote TTL systems, teach MiniTT1 unit to be used as primary transmitter rst, then use it to teach all FlexTT5 units. MiniTT1 and FlexTT5 units send out both ControlTL and Legacy triggers every time they are triggered. For remote TTL to function, ControlTL channel must be learned. If you see only 1 or 2 green blinks, and you desire TTL, teach again with MiniTT1 or FlexTT5 unit. Look for 3 green blinks to verify ControlTL is learned. To teach all units Legacy channels, use Legacy Transmitter as teaching unit for all learning units, including MiniTT1 unit to be used as primary transmitter. To avoid inadvertent ashing from remote units that have already been taught or have already had channel set, turn them OFF. MiniTT1 Plus II, MultiMAX, Integrated, or FlexTT5 connected to manual ash Remote ash with or without TTL ash on camera 1. Slide MiniTT1 Transmitter onto camera. 2. If desired, slide Canon E-TTL Speedlite (MASTER = ON) onto MiniTT1 unit. 3. Make sure all your PocketWizard units are on the same Channel and trigger normally. Note: Manual remote ashes are not calculated as part of the E-TTL exposure. Be sure to set on-camera FEC if remote ash is illuminating same subject as your E-TTL ash. ZeroSync occurs automatically. Trigger as fast as a wire with all PocketWizard radios. Use PocketWizard Utility to engage HyperSync and explore faster than X-sync shutter speeds. See user manual at www.pocketwizard.com for more information. Auto-Relay Mode A FlexTT5 unit in cameras shoe and connected with motor drive cord to P1 can receive a radio trigger, trigger the cameras motor drive which in turn triggers a remote ash. The channel used for relay transmit is 1 higher than taught channel, unless set via PocketWizard Utility. Example: if you taught FlexTT5 unit Channel 3 then relay transmit occurs on Channel 4. Press TEST on hand-held trigger unit to begin relay sequence. RESET to Default Settings RESET A: To reset Learned Channels, hold TEST on power up. LED blinks green twice to indicate reset. Release TEST. Advanced Features set via USB are retained. A: Default Channels C1 = ControlTL Channel 1, Legacy Channel 1 C2 = ControlTL Channel 2, Legacy Channel 2 Green Good battery Amber Warning battery low Red Status LED Normal waiting for trigger operation = short blink every 2 seconds. Normal short blink color indicates Battery Level:
Steady red LED in sync with TEST indicates normal transmission.
(Hold for 10 seconds to teach see LEARN mode) Short red blink in sync with trigger indicates normal reception. Rapid red blinking when not triggering or half-pressing camera indicates error condition. Power off the unit, reseat all connections, and power back on. Very low battery change immediately RESET A & B: To reset all Advanced Features and Learned Channels to FACTORY DEFAULTS, hold TEST on power up for longer than 10 seconds. When LED blinks green 4 times, release. B: Default Advanced Features Auto ISO and Aperture Tracking Enabled Exposure Compensation Center Value = 3.5 HyperSync Offset = -250 microseconds Remote TTL Flash Sleep Mode = Disabled Camera Model = Auto All settings may be congured using the PocketWizard Utility available from www.pocketwizard.com www.pocketwizard.com LEARN Mode Manual Flash Other Functions Specications Trigger Delay = 0 seconds fast as a wire Batteries: MiniTT1 = CR2450 or CR2354 (100s of hours) Maximum FPS: Up to 12 (varies with camera, E-TTL usage reduces FPS) E-TTL: E-TTL I & E-TTL II (DSLR only, not for lm TTL) Operating Temperature: Above -15 C (5 F) and below 50 C (120 F) Storage Temperature (without battery): Above -30 C (-22 F) and below 85 C (185 F) FlexTT5 = 2 x AA (IEC:LR6) (60 hours) Powerable via USB AC adapter (powering from computer USB port not recommended) This US FCC/Canada IC frequency PocketWizard radio slave is compatible with all US frequency PocketWizard products. It is not frequency compatible with CE or JAPAN PocketWizard products. Verify frequency compatibility before purchasing. 2009 LPA Design, Inc. All rights reserved. Product features and specications are subject to change without notice. PocketWizard, ControlTL, MiniTT1, FlexTT5, HyperSync, ZeroSync, Plus II and MultiMAX are either trademarks or registered trademarks of LPA Design, Inc. All other trademarks contained herein are the property of their respective owners. US Patent: 5,359,375 and Patents Pending V1.0 January 2009 LPF374 For more information on this product, including detailed features, specications and the complete user manual, go to www.pocketwizard.com. This product is covered under a warranty. For more information on the warranty and to register your product, please go to www.pocketwizard.com/support. MAKE IT POSSIBLE Channels can be taught via PocketWizard Utility or from any PocketWizard Transmitter using LEARN mode:
IMPORTANT: Hold units at least 2 feet apart when teaching/learning. 1. Turn MiniTT1 or FlexTT5 unit ON and select Channel to be taught. 2. Press and hold TEST for several seconds until LED blinks amber, then release TEST. 3. Quickly press and hold TEST on teaching Transmitting unit (MiniTT1, FlexTT5, Plus II or MultiMAX). When LED blinks green, channel is learned. Connected ash may 1 green blink = Low Legacy Channel learned (1 through 16) 2 green blinks = High Legacy Channel learned (MultiMAX 17 through 32) 3 green blinks = ControlTL Channel learned (ControlTL 1 through 20) trigger during LEARN. For remote TTL systems, teach MiniTT1 unit to be used as primary transmitter rst, then use it to teach all FlexTT5 units. MiniTT1 and FlexTT5 units send out both ControlTL and Legacy triggers every time they are triggered. For remote TTL to function, ControlTL channel must be learned. If you see only 1 or 2 green blinks, and you desire TTL, teach again with MiniTT1 or FlexTT5 unit. Look for 3 green blinks to verify ControlTL is learned. To teach all units Legacy channels, use Legacy Transmitter as teaching unit for all learning units, including MiniTT1 unit to be used as primary transmitter. To avoid inadvertent ashing from remote units that have already been taught or have already had channel set, turn them OFF. MiniTT1 Plus II, MultiMAX, Integrated, or FlexTT5 connected to manual ash Remote ash with or without TTL ash on camera 1. Slide MiniTT1 Transmitter onto camera. 2. If desired, slide Canon E-TTL Speedlite (MASTER = ON) onto MiniTT1 unit. 3. Make sure all your PocketWizard units are on the same Channel and trigger normally. Note: Manual remote ashes are not calculated as part of the E-TTL exposure. Be sure to set on-camera FEC if remote ash is illuminating same subject as your E-TTL ash. ZeroSync occurs automatically. Trigger as fast as a wire with all PocketWizard radios. Use PocketWizard Utility to engage HyperSync and explore faster than X-sync shutter speeds. See user manual at www.pocketwizard.com for more information. Auto-Relay Mode A FlexTT5 unit in cameras shoe and connected with motor drive cord to P1 can receive a radio trigger, trigger the cameras motor drive which in turn triggers a remote ash. The channel used for relay transmit is 1 higher than taught channel, unless set via PocketWizard Utility. Example: if you taught FlexTT5 unit Channel 3 then relay transmit occurs on Channel 4. Press TEST on hand-held trigger unit to begin relay sequence. RESET to Default Settings RESET A: To reset Learned Channels, hold TEST on power up. LED blinks green twice to indicate reset. Release TEST. Advanced Features set via USB are retained. A: Default Channels C1 = ControlTL Channel 1, Legacy Channel 1 C2 = ControlTL Channel 2, Legacy Channel 2 Green Good battery Amber Warning battery low Red Status LED Normal waiting for trigger operation = short blink every 2 seconds. Normal short blink color indicates Battery Level:
Steady red LED in sync with TEST indicates normal transmission.
(Hold for 10 seconds to teach see LEARN mode) Short red blink in sync with trigger indicates normal reception. Rapid red blinking when not triggering or half-pressing camera indicates error condition. Power off the unit, reseat all connections, and power back on. Very low battery change immediately RESET A & B: To reset all Advanced Features and Learned Channels to FACTORY DEFAULTS, hold TEST on power up for longer than 10 seconds. When LED blinks green 4 times, release. B: Default Advanced Features Auto ISO and Aperture Tracking Enabled Exposure Compensation Center Value = 3.5 HyperSync Offset = -250 microseconds Remote TTL Flash Sleep Mode = Disabled Camera Model = Auto All settings may be congured using the PocketWizard Utility available from www.pocketwizard.com www.pocketwizard.com LEARN Mode Manual Flash Other Functions Specications Trigger Delay = 0 seconds fast as a wire Batteries: MiniTT1 = CR2450 or CR2354 (100s of hours) Maximum FPS: Up to 12 (varies with camera, E-TTL usage reduces FPS) E-TTL: E-TTL I & E-TTL II (DSLR only, not for lm TTL) Operating Temperature: Above -15 C (5 F) and below 50 C (120 F) Storage Temperature (without battery): Above -30 C (-22 F) and below 85 C (185 F) FlexTT5 = 2 x AA (IEC:LR6) (60 hours) Powerable via USB AC adapter (powering from computer USB port not recommended) This US FCC/Canada IC frequency PocketWizard radio slave is compatible with all US frequency PocketWizard products. It is not frequency compatible with CE or JAPAN PocketWizard products. Verify frequency compatibility before purchasing. 2009 LPA Design, Inc. All rights reserved. Product features and specications are subject to change without notice. PocketWizard, ControlTL, MiniTT1, FlexTT5, HyperSync, ZeroSync, Plus II and MultiMAX are either trademarks or registered trademarks of LPA Design, Inc. All other trademarks contained herein are the property of their respective owners. US Patent: 5,359,375 and Patents Pending V1.0 January 2009 LPF374 For more information on this product, including detailed features, specications and the complete user manual, go to www.pocketwizard.com. This product is covered under a warranty. For more information on the warranty and to register your product, please go to www.pocketwizard.com/support. MAKE IT POSSIBLE Channels can be taught via PocketWizard Utility or from any PocketWizard Transmitter using LEARN mode:
IMPORTANT: Hold units at least 2 feet apart when teaching/learning. 1. Turn MiniTT1 or FlexTT5 unit ON and select Channel to be taught. 2. Press and hold TEST for several seconds until LED blinks amber, then release TEST. 3. Quickly press and hold TEST on teaching Transmitting unit (MiniTT1, FlexTT5, Plus II or MultiMAX). When LED blinks green, channel is learned. Connected ash may 1 green blink = Low Legacy Channel learned (1 through 16) 2 green blinks = High Legacy Channel learned (MultiMAX 17 through 32) 3 green blinks = ControlTL Channel learned (ControlTL 1 through 20) trigger during LEARN. For remote TTL systems, teach MiniTT1 unit to be used as primary transmitter rst, then use it to teach all FlexTT5 units. MiniTT1 and FlexTT5 units send out both ControlTL and Legacy triggers every time they are triggered. For remote TTL to function, ControlTL channel must be learned. If you see only 1 or 2 green blinks, and you desire TTL, teach again with MiniTT1 or FlexTT5 unit. Look for 3 green blinks to verify ControlTL is learned. To teach all units Legacy channels, use Legacy Transmitter as teaching unit for all learning units, including MiniTT1 unit to be used as primary transmitter. To avoid inadvertent ashing from remote units that have already been taught or have already had channel set, turn them OFF. MiniTT1 Plus II, MultiMAX, Integrated, or FlexTT5 connected to manual ash Remote ash with or without TTL ash on camera 1. Slide MiniTT1 Transmitter onto camera. 2. If desired, slide Canon E-TTL Speedlite (MASTER = ON) onto MiniTT1 unit. 3. Make sure all your PocketWizard units are on the same Channel and trigger normally. Note: Manual remote ashes are not calculated as part of the E-TTL exposure. Be sure to set on-camera FEC if remote ash is illuminating same subject as your E-TTL ash. ZeroSync occurs automatically. Trigger as fast as a wire with all PocketWizard radios. Use PocketWizard Utility to engage HyperSync and explore faster than X-sync shutter speeds. See user manual at www.pocketwizard.com for more information. Auto-Relay Mode A FlexTT5 unit in cameras shoe and connected with motor drive cord to P1 can receive a radio trigger, trigger the cameras motor drive which in turn triggers a remote ash. The channel used for relay transmit is 1 higher than taught channel, unless set via PocketWizard Utility. Example: if you taught FlexTT5 unit Channel 3 then relay transmit occurs on Channel 4. Press TEST on hand-held trigger unit to begin relay sequence. RESET to Default Settings RESET A: To reset Learned Channels, hold TEST on power up. LED blinks green twice to indicate reset. Release TEST. Advanced Features set via USB are retained. A: Default Channels C1 = ControlTL Channel 1, Legacy Channel 1 C2 = ControlTL Channel 2, Legacy Channel 2 Green Good battery Amber Warning battery low Red Status LED Normal waiting for trigger operation = short blink every 2 seconds. Normal short blink color indicates Battery Level:
Steady red LED in sync with TEST indicates normal transmission.
(Hold for 10 seconds to teach see LEARN mode) Short red blink in sync with trigger indicates normal reception. Rapid red blinking when not triggering or half-pressing camera indicates error condition. Power off the unit, reseat all connections, and power back on. Very low battery change immediately RESET A & B: To reset all Advanced Features and Learned Channels to FACTORY DEFAULTS, hold TEST on power up for longer than 10 seconds. When LED blinks green 4 times, release. B: Default Advanced Features Auto ISO and Aperture Tracking Enabled Exposure Compensation Center Value = 3.5 HyperSync Offset = -250 microseconds Remote TTL Flash Sleep Mode = Disabled Camera Model = Auto All settings may be congured using the PocketWizard Utility available from www.pocketwizard.com www.pocketwizard.com LEARN Mode Manual Flash Other Functions Specications Trigger Delay = 0 seconds fast as a wire Batteries: MiniTT1 = CR2450 or CR2354 (100s of hours) Maximum FPS: Up to 12 (varies with camera, E-TTL usage reduces FPS) E-TTL: E-TTL I & E-TTL II (DSLR only, not for lm TTL) Operating Temperature: Above -15 C (5 F) and below 50 C (120 F) Storage Temperature (without battery): Above -30 C (-22 F) and below 85 C (185 F) FlexTT5 = 2 x AA (IEC:LR6) (60 hours) Powerable via USB AC adapter (powering from computer USB port not recommended) This US FCC/Canada IC frequency PocketWizard radio slave is compatible with all US frequency PocketWizard products. It is not frequency compatible with CE or JAPAN PocketWizard products. Verify frequency compatibility before purchasing. 2009 LPA Design, Inc. All rights reserved. Product features and specications are subject to change without notice. PocketWizard, ControlTL, MiniTT1, FlexTT5, HyperSync, ZeroSync, Plus II and MultiMAX are either trademarks or registered trademarks of LPA Design, Inc. All other trademarks contained herein are the property of their respective owners. US Patent: 5,359,375 and Patents Pending V1.0 January 2009 LPF374 For more information on this product, including detailed features, specications and the complete user manual, go to www.pocketwizard.com. This product is covered under a warranty. For more information on the warranty and to register your product, please go to www.pocketwizard.com/support. MAKE IT POSSIBLE Channels can be taught via PocketWizard Utility or from any PocketWizard Transmitter using LEARN mode:
IMPORTANT: Hold units at least 2 feet apart when teaching/learning. 1. Turn MiniTT1 or FlexTT5 unit ON and select Channel to be taught. 2. Press and hold TEST for several seconds until LED blinks amber, then release TEST. 3. Quickly press and hold TEST on teaching Transmitting unit (MiniTT1, FlexTT5, Plus II or MultiMAX). When LED blinks green, channel is learned. Connected ash may 1 green blink = Low Legacy Channel learned (1 through 16) 2 green blinks = High Legacy Channel learned (MultiMAX 17 through 32) 3 green blinks = ControlTL Channel learned (ControlTL 1 through 20) trigger during LEARN. For remote TTL systems, teach MiniTT1 unit to be used as primary transmitter rst, then use it to teach all FlexTT5 units. MiniTT1 and FlexTT5 units send out both ControlTL and Legacy triggers every time they are triggered. For remote TTL to function, ControlTL channel must be learned. If you see only 1 or 2 green blinks, and you desire TTL, teach again with MiniTT1 or FlexTT5 unit. Look for 3 green blinks to verify ControlTL is learned. To teach all units Legacy channels, use Legacy Transmitter as teaching unit for all learning units, including MiniTT1 unit to be used as primary transmitter. To avoid inadvertent ashing from remote units that have already been taught or have already had channel set, turn them OFF. MiniTT1 Plus II, MultiMAX, Integrated, or FlexTT5 connected to manual ash Remote ash with or without TTL ash on camera 1. Slide MiniTT1 Transmitter onto camera. 2. If desired, slide Canon E-TTL Speedlite (MASTER = ON) onto MiniTT1 unit. 3. Make sure all your PocketWizard units are on the same Channel and trigger normally. Note: Manual remote ashes are not calculated as part of the E-TTL exposure. Be sure to set on-camera FEC if remote ash is illuminating same subject as your E-TTL ash. ZeroSync occurs automatically. Trigger as fast as a wire with all PocketWizard radios. Use PocketWizard Utility to engage HyperSync and explore faster than X-sync shutter speeds. See user manual at www.pocketwizard.com for more information. Auto-Relay Mode A FlexTT5 unit in cameras shoe and connected with motor drive cord to P1 can receive a radio trigger, trigger the cameras motor drive which in turn triggers a remote ash. The channel used for relay transmit is 1 higher than taught channel, unless set via PocketWizard Utility. Example: if you taught FlexTT5 unit Channel 3 then relay transmit occurs on Channel 4. Press TEST on hand-held trigger unit to begin relay sequence. RESET to Default Settings RESET A: To reset Learned Channels, hold TEST on power up. LED blinks green twice to indicate reset. Release TEST. Advanced Features set via USB are retained. A: Default Channels C1 = ControlTL Channel 1, Legacy Channel 1 C2 = ControlTL Channel 2, Legacy Channel 2 Green Good battery Amber Warning battery low Red Status LED Normal waiting for trigger operation = short blink every 2 seconds. Normal short blink color indicates Battery Level:
Steady red LED in sync with TEST indicates normal transmission.
(Hold for 10 seconds to teach see LEARN mode) Short red blink in sync with trigger indicates normal reception. Rapid red blinking when not triggering or half-pressing camera indicates error condition. Power off the unit, reseat all connections, and power back on. Very low battery change immediately RESET A & B: To reset all Advanced Features and Learned Channels to FACTORY DEFAULTS, hold TEST on power up for longer than 10 seconds. When LED blinks green 4 times, release. B: Default Advanced Features Auto ISO and Aperture Tracking Enabled Exposure Compensation Center Value = 3.5 HyperSync Offset = -250 microseconds Remote TTL Flash Sleep Mode = Disabled Camera Model = Auto All settings may be congured using the PocketWizard Utility available from www.pocketwizard.com
frequency | equipment class | purpose | ||
---|---|---|---|---|
1 | 2009-02-11 | 340 ~ 354 | DSR - Part 15 Remote Control/Security Device Transceiver | Original Equipment |
app s | Applicant Information | |||||
---|---|---|---|---|---|---|
1 | Effective |
2009-02-11
|
||||
1 | Applicant's complete, legal business name |
Lab Partners Associates Inc
|
||||
1 | FCC Registration Number (FRN) |
0006223671
|
||||
1 | Physical Address |
21 Gregory Drive
|
||||
1 |
South Burlington, Vermont 05403
|
|||||
1 |
United States
|
|||||
app s | TCB Information | |||||
1 | TCB Application Email Address |
d******@elitetest.com
|
||||
1 | TCB Scope |
A1: Low Power Transmitters below 1 GHz (except Spread Spectrum), Unintentional Radiators, EAS (Part 11) & Consumer ISM devices
|
||||
app s | FCC ID | |||||
1 | Grantee Code |
KDS
|
||||
1 | Equipment Product Code |
PW3-005
|
||||
app s | Person at the applicant's address to receive grant or for contact | |||||
1 | Name |
B**** B********
|
||||
1 | Title |
General Manager
|
||||
1 | Telephone Number |
802-7********
|
||||
1 | Fax Number |
802-6********
|
||||
1 |
b******@lpadesign.com
|
|||||
app s | Technical Contact | |||||
1 | Firm Name |
Retlif Testing Laboratories
|
||||
1 | Name |
S******** W********
|
||||
1 | Physical Address |
101 New Boston Road
|
||||
1 |
Goffstown, New Hampshire 03045
|
|||||
1 |
United States
|
|||||
1 | Telephone Number |
603-4******** Extension:
|
||||
1 | Fax Number |
603-4********
|
||||
1 |
s******@retlif.com
|
|||||
app s | Non Technical Contact | |||||
1 | Firm Name |
Retlif Testing Laboratories
|
||||
1 | Name |
S****** W********
|
||||
1 | Physical Address |
101 New Boston Road
|
||||
1 |
Goffstown, New Hampshire 03045
|
|||||
1 |
United States
|
|||||
1 | Telephone Number |
603-4******** Extension:
|
||||
1 | Fax Number |
603-4********
|
||||
1 |
s******@retlif.com
|
|||||
app s | Confidentiality (long or short term) | |||||
1 | Does this application include a request for confidentiality for any portion(s) of the data contained in this application pursuant to 47 CFR § 0.459 of the Commission Rules?: | Yes | ||||
1 | Long-Term Confidentiality Does this application include a request for confidentiality for any portion(s) of the data contained in this application pursuant to 47 CFR § 0.459 of the Commission Rules?: | No | ||||
if no date is supplied, the release date will be set to 45 calendar days past the date of grant. | ||||||
app s | Cognitive Radio & Software Defined Radio, Class, etc | |||||
1 | Is this application for software defined/cognitive radio authorization? | No | ||||
1 | Equipment Class | DSR - Part 15 Remote Control/Security Device Transceiver | ||||
1 | Description of product as it is marketed: (NOTE: This text will appear below the equipment class on the grant) | Remote Control Flash Transceiver | ||||
1 | Related OET KnowledgeDataBase Inquiry: Is there a KDB inquiry associated with this application? | No | ||||
1 | Modular Equipment Type | Does not apply | ||||
1 | Purpose / Application is for | Original Equipment | ||||
1 | Composite Equipment: Is the equipment in this application a composite device subject to an additional equipment authorization? | No | ||||
1 | Related Equipment: Is the equipment in this application part of a system that operates with, or is marketed with, another device that requires an equipment authorization? | No | ||||
1 | Is there an equipment authorization waiver associated with this application? | No | ||||
1 | If there is an equipment authorization waiver associated with this application, has the associated waiver been approved and all information uploaded? | No | ||||
app s | Test Firm Name and Contact Information | |||||
1 | Firm Name |
Retlif Testing Laboratories
|
||||
1 | Name |
S******** W****
|
||||
1 | Telephone Number |
603-4********
|
||||
1 | Fax Number |
603-4********
|
||||
1 |
m******@retlif.com
|
|||||
Equipment Specifications | |||||||||||||||||||||||||||||||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
Line | Rule Parts | Grant Notes | Lower Frequency | Upper Frequency | Power Output | Tolerance | Emission Designator | Microprocessor Number | |||||||||||||||||||||||||||||||||
1 | 1 | 15.231 | 340.00000000 | 354.00000000 |
some individual PII (Personally Identifiable Information) available on the public forms may be redacted, original source may include additional details
This product uses the FCC Data API but is not endorsed or certified by the FCC